Last active
July 28, 2022 19:47
-
-
Save mikejr83/fa3bbd32c5b5d4217281881ceab9dfa5 to your computer and use it in GitHub Desktop.
Various Custom G-Code for the Artist-D in Prusa Slicer
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
G91 ;Relative positioning | |
G0 E-2 F2700 ;Retract a bit | |
G0 E-2 Z0.2 F2400 ;Retract and raise Z | |
G0 X5 Y5 F3000 ;Wipe out | |
G0 Z10 ;Raise Z more | |
G90 ;Absolute positionning | |
G0 Y310 ;Present print | |
M106 S0 ;Turn-off fan | |
M104 S0 T0 ;Turn-off hotend 1 | |
M104 S0 T1 ;Turn-off hotend 2 | |
M140 S0 ;Turn-off bed | |
G28X ; Home x-carriages | |
M605 S1 ; Reset to auto-park | |
M84 X Y E ;Disable all steppers but Z |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
G91 ;Relative positioning | |
G0 E-2 F2700 ;Retract a bit | |
G0 E-2 Z0.2 F2400 ;Retract and raise Z | |
G0 X5 Y5 F3000 ;Wipe out | |
G0 Z10 ;Raise Z more | |
G90 ;Absolute positionning | |
{if current_extruder==0} | |
G0 X0 Y310 ;Present print | |
{else} | |
G0 X310 Y310 ;Present print | |
{endif} | |
M106 S0 ;Turn-off fan | |
M104 S0 T0 ;Turn-off hotend 1 | |
M104 S0 T1 ;Turn-off hotend 2 | |
M140 S0 ;Turn-off bed | |
G28X ; Home x-carriages | |
M84 X Y E ;Disable all steppers but Z |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
; -- BEGIN - DUPLICATION MODE INITIALIZATION -- | |
M605 S1 ; AUTO-PARK MODE | |
T0 ; SET TOOL 0 | |
G28 ; HOME ALL AXIS | |
M605 S2 X155 ; SET DUPLICATION MODE AND NOZZLE OFFSET | |
G28 X ; HOME X AXIS | |
G1 X77.5 ; SET BOTH EXTRUDERS TO THE MIDDLE OF THEIR PRINT AREA | |
; -- END - DUPLICATION MODE INITIALIZATION | |
M140 S[first_layer_bed_temperature] ; Set Heat Bed temperature | |
M104 S[first_layer_temperature] ; Set Extruder temperature | |
M190 S[first_layer_bed_temperature] ; Wait for Heat Bed temperature | |
G1 Z15.0 F6000 ;Move the platform down 15mm | |
;Prime the extruder | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X10 Y20 Z0.3 F5000.0 ; Move to start position | |
M109 S[first_layer_temperature] ; Wait for Extruder temperature | |
G1 X10 Y200.0 Z0.2 F1500.0 E15 ; Draw the first line | |
G1 X10.3 Y200.0 Z0.2 F5000.0 ; Move to side a little | |
G1 X10.3 Y20 Z0.2 F1500.0 E30 ; Draw the second line | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X14 Y20 Z0.2 F5000.0 ; Move over to prevent blob squish |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
; -- BEGIN - MIRROR MODE INITIALIZATION -- | |
M605 S1 | |
T0 | |
G28 | |
M605 S2 X155 | |
G28 X | |
G1 X77.5 | |
M605 S3 X155 | |
; -- END - MIRROR MODE INITIALIZATION | |
M140 S[first_layer_bed_temperature] ; Set Heat Bed temperature | |
M104 S[first_layer_temperature] ; Set Extruder temperature | |
M190 S[first_layer_bed_temperature] ; Wait for Heat Bed temperature | |
G1 Z15.0 F6000 ;Move the platform down 15mm | |
;Prime the extruder | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X10 Y20 Z0.3 F5000.0 ; Move to start position | |
M109 S[first_layer_temperature] ; Wait for Extruder temperature | |
G1 X10 Y200.0 Z0.2 F1500.0 E15 ; Draw the first line | |
G1 X10.3 Y200.0 Z0.2 F5000.0 ; Move to side a little | |
G1 X10.3 Y20 Z0.2 F1500.0 E30 ; Draw the second line | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X14 Y20 Z0.2 F5000.0 ; Move over to prevent blob squish |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
M605S1 ; Set to auto-park | |
T[initial_tool] | |
M140 S[first_layer_bed_temperature] ; Set Heat Bed temperature | |
M104 S[first_layer_temperature_[initial_tool]] ; Set Extruder temperature | |
G28 ;Home | |
M190 S[first_layer_bed_temperature] ; Wait for Heat Bed temperature | |
G1 Z15.0 F6000 ;Move the platform down 15mm | |
;Prime the extruder | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X10 Y20 Z0.3 F5000.0 ; Move to start position | |
M109 S[first_layer_temperature_[initial_tool]] ; Wait for Extruder temperature | |
G1 X10 Y200.0 Z0.2 F1500.0 E15 ; Draw the first line | |
G1 X10.3 Y200.0 Z0.2 F5000.0 ; Move to side a little | |
G1 X10.3 Y20 Z0.2 F1500.0 E30 ; Draw the second line | |
G92 E0 ; Reset Extruder | |
G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed | |
G1 X14 Y20 Z0.2 F5000.0 ; Move over to prevent blob squish |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
; TOOL CHANGE ---START--- | |
T[next_extruder] | |
{if current_extruder != next_extruder} | |
M104 S175 T[current_extruder] | |
{endif} | |
{if layer_num==0} | |
M109 S[first_layer_temperature_[next_extruder]] T[next_extruder] ; Wait for Extruder temperature | |
{else} | |
M109 S[temperature_[next_extruder]] T[next_extruder] ; Wait for Extruder temperature | |
{endif} | |
; TOOL CHANGE ---END--- |
@jpswensen We have a good set of guys running the artist over on our Discord: https://discord.gg/vJ6GxxKW "3D Misfits". Please come and ask any questions. We'll be glad to help you out.
@mikejr83 , I tried to join that group and it just gave a "Whoops. Unable to accept invite" error. I am wonder if the group has been closed?
Try this link https://discord.gg/Y9Q7Ubew8v
…On Mon, Jul 18, 2022, 5:58 PM John P. Swensen ***@***.***> wrote:
***@***.**** commented on this gist.
------------------------------
@mikejr83 <https://github.com/mikejr83> , I tried to join that group and
it just gave a "Whoops. Unable to accept invite" error. I am wonder if the
group has been closed?
—
Reply to this email directly, view it on GitHub
<https://gist.github.com/fa3bbd32c5b5d4217281881ceab9dfa5#gistcomment-4236646>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AAY5UP3VPXESQPGY2FM6JB3VUXHOTANCNFSM44FUNQBA>
.
You are receiving this because you were mentioned.Message ID:
***@***.***
.com>
That one didn’t work either. Here is a link.
… On Jul 18, 2022, at 3:22 PM, Mike ***@***.***> wrote:
@mikejr83 commented on this gist.
Try this link https://discord.gg/Y9Q7Ubew8v
On Mon, Jul 18, 2022, 5:58 PM John P. Swensen ***@***.***>
wrote:
> ***@***.**** commented on this gist.
> ------------------------------
>
> @mikejr83 <https://github.com/mikejr83> , I tried to join that group and
> it just gave a "Whoops. Unable to accept invite" error. I am wonder if the
> group has been closed?
>
> —
> Reply to this email directly, view it on GitHub
> <https://gist.github.com/fa3bbd32c5b5d4217281881ceab9dfa5#gistcomment-4236646>,
> or unsubscribe
> <https://github.com/notifications/unsubscribe-auth/AAY5UP3VPXESQPGY2FM6JB3VUXHOTANCNFSM44FUNQBA>
> .
> You are receiving this because you were mentioned.Message ID:
> ***@***.***
> .com>
>
—
Reply to this email directly, view it on GitHub <https://gist.github.com/fa3bbd32c5b5d4217281881ceab9dfa5#gistcomment-4236652>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AAFQKJGDFX3WVAIFZTGVDK3VUXKJJANCNFSM44FUNQBA>.
You are receiving this because you were mentioned.
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Thank you so much! I think that will help me get up and running quickly. I am going to try and tune some of them for PLA and PVA dissolvable support. I will come back and post my results here if I get a good combination.