Last active
September 14, 2017 06:05
-
-
Save morimolymoly/60fe120b5f425419634c890fa40d7dbb to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
m | |
1. HiZ | |
2. 1-WIRE | |
3. UART | |
4. I2C | |
5. SPI | |
6. 2WIRE | |
7. 3WIRE | |
8. LCD | |
9. DIO | |
x. exit(without change) | |
(1)>3 | |
Set serial port speed: (bps) | |
1. 300 | |
2. 1200 | |
3. 2400 | |
4. 4800 | |
5. 9600 | |
6. 19200 | |
7. 38400 | |
8. 57600 | |
9. 115200 | |
10. BRG raw value | |
(1)>8 | |
Data bits and parity: | |
1. 8, NONE *default | |
2. 8, EVEN | |
3. 8, ODD | |
4. 9, NONE | |
(1)> | |
Stop bits: | |
1. 1 *default | |
2. 2 | |
(1)> | |
Receive polarity: | |
1. Idle 1 *default | |
2. Idle 0 | |
(1)> | |
Select output type: | |
1. Open drain (H=Hi-Z, L=GND) | |
2. Normal (H=3.3V, L=GND) | |
(1)>2 | |
Ready | |
UART>(2) | |
Raw UART input | |
Any key to exit | |
U-Boot 1.1.3 (Feb 25 2009 - 17:15:59) | |
Board: Ralink APSoC DRAM: 16 MB | |
relocate_code Pointer at: 80fa8000 | |
flash_protect ON: from 0xBF000000 to 0xBF024F2F | |
protect on 0 | |
protect on 1 | |
protect on 2 | |
protect on 3 | |
protect on 4 | |
protect on 5 | |
protect on 6 | |
protect on 7 | |
protect on 8 | |
protect on 9 | |
flash_protect ON: from 0xBF030000 to 0xBF03FFFF | |
protect on 10 | |
============================================ | |
Ralink UBoot Version: 3.2 | |
-------------------------------------------- | |
ASIC 3052_MP2 (Port5<->None) | |
DRAM COMPONENT: 128Mbits | |
DRAM BUS: 16BIT | |
Total memory: 16 MBytes | |
Date:Feb 25 2009 Time:17:15:59 | |
============================================ | |
icache: sets:256, ways:4, linesz:32 ,total:32768 | |
dcache: sets:128, ways:4, linesz:32 ,total:16384 | |
##### The CPU freq = 320 MHZ #### | |
SDRAM bus set to 16 bit | |
SDRAM size =16 Mbytes | |
Please choose the operation: | |
1: Load system code to SDRAM via TFTP. | |
2: Load system code then write to Flash via TFTP. | |
3: Boot system code via Flash (default). | |
4: Entr boot command line interface. | |
9: Load Boot Loader code then write to Flash via TFTP. | |
You choosed 3 | |
0 | |
3: System Boot system code via Flash. | |
eth_register | |
Eth0 (10/100-M) | |
enetvar=ethaddr,Eth addr:00:AA:BB:CC:DD:10 | |
00:AA:BB:CC:DD:10: | |
eth_current->name = Eth0 (10/100-M) | |
## Booting image at bf050000 ... | |
Image Name: Linux Kernel Image | |
Created: 2009-02-26 3:36:39 UTC | |
System Control Status = 0x03400000 | |
Image Type: MIPS Linux Kernel Image (lzma compressed) | |
Data Size: 3391424 Bytes = 3.2 MB | |
Load Address: 80000000 | |
Entry Point: 80382000 | |
Verifying Checksum ... OK | |
Uncompressing Kernel Image ... OK | |
No initrd | |
## Transferring control to Linux (at address 80382000) ... | |
## Giving linux memsize in MB, 16 | |
Starting kernel ... | |
LINUX started... | |
THIS IS ASIC | |
Linux version 2.6.21 (root@localhost.localdomain) (gcc version 3.3.6) #50 Thu Feb 26 11:33:32 CST 2009 | |
The CPU feqenuce set to 320 MHz | |
CPU revision is: 0001964c | |
Determined physical RAM map: | |
memory: 01000000 @ 00000000 (usable) | |
Built 1 zonelists. Total pages: 4064 | |
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock2 | |
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. | |
Primary data cache 16kB, 4-way, linesize 32 bytes. | |
Synthesized TLB refill handler (20 instructions). | |
Synthesized TLB load handler fastpath (32 instructions). | |
Synthesized TLB store handler fastpath (32 instructions). | |
Synthesized TLB modify handler fastpath (31 instructions). | |
Cache parity protection disabled | |
cause = 80000c, status = 1100ff00 | |
PID hash table entries: 64 (order: 6, 256 bytes) | |
calculating r4koff... 00138800(1280000) | |
CPU frequency 320.00 MHz | |
Using 160.000 MHz high precision timer. | |
Console: colour dummy device 80x25 | |
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) | |
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
Memory: 12040k/16384k available (2779k kernel code, 4344k reserved, 808k data, 124k init, 0k highmem) | |
Mount-cache hash table entries: 512 | |
NET: Registered protocol family 16 | |
Time: MIPS clocksource has been installed. | |
NET: Registered protocol family 2 | |
IP route cache hash table entries: 1024 (order: 0, 4096 bytes) | |
TCP established hash table entries: 512 (order: 0, 4096 bytes) | |
TCP bind hash table entries: 512 (order: -1, 2048 bytes) | |
TCP: Hash tables configured (established 512 bind 512) | |
TCP reno registered | |
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher | |
squashfs: LZMA suppport for slax.org by jro | |
io scheduler noop registered (default) | |
FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB | |
Ralink gpio driver initialized | |
StatusLEDThread pid : 113 | |
Initialziing the INTERNET LED control module ... successful | |
Initialziing the WSC LED control module ... successful | |
Initialziing the LED control module ... successful | |
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled | |
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A | |
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A | |
loop: loaded (max 8 devices) | |
GDMA1_MAC_ADRH -- : 0x00000000 | |
GDMA1_MAC_ADRL -- : 0x00000000 | |
Ralink APSoC Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocated, mtu = 1600! | |
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256 | |
GDMA1_MAC_ADRH -- : 0x00000000 | |
GDMA1_MAC_ADRL -- : 0x000a79e2 | |
PROC INIT OK! | |
GTK :: To segment the WAN/LAN as LLLLW, Port 0 ~ 4 ... successfully | |
PPP generic driver version 2.4.2 | |
PPP BSD Compression module registered | |
NET: Registered protocol family 24 | |
2860 version : 1.9.0.0 (Feb 26 2009) | |
=== pAd = c0000000, size = 485872 === | |
<-- RTMPAllocAdapterBlock, Status=0 | |
ralink flash device: 0x1000000 at 0xbf000000 | |
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank | |
Amd/Fujitsu Extended Query Table at 0x0040 | |
number of CFI chips: 1 | |
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. | |
Creating 5 MTD partitions on "Ralink SoC physically mapped flash": | |
0x00000000-0x00050000 : "uBoot" | |
mtd: Giving out device 0 to uBoot | |
0x00050000-0x00190000 : "Linux Kernel" | |
mtd: Giving out device 1 to Linux Kernel | |
0x00190000-0x003e0000 : "RootFS" | |
mtd: Giving out device 2 to RootFS | |
0x003e0000-0x003f0000 : "NVRAM" | |
mtd: Giving out device 3 to NVRAM | |
0x003f0000-0x00400000 : "NVRAM_FACTORY" | |
mtd: Giving out device 4 to NVRAM_FACTORY | |
block2mtd: version $Revision: 1.1.1.1 $ | |
nf_conntrack version 0.5.0 (128 buckets, 1024 max) | |
GRE over IPv4 tunneling driver | |
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Fully Cone | |
ClusterIP Version 0.8 loaded successfully | |
arp_tables: (C) 2002 David S. Miller | |
TCP cubic registered | |
NET: Registered protocol family 1 | |
NET: Registered protocol family 17 | |
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> | |
All bugs added by David S. Miller <davem@redhat.com> | |
VFS: Mounted root (squashfs filesystem) readonly. | |
Freeing unused kernel memory: 124k freed | |
(main)331 | |
Algorithmics/MIPS FPU Emulator v1.5 | |
init: cannot open inittab | |
toks= /bin/sh (null) (null) (null) | |
tty= console | |
termcap= linux | |
BusyBox v1.8.2 (2009-02-26 11:34:39 CST) built-in shell (ash) | |
Enter 'help' for a list of built-in commands. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment