Created
May 31, 2016 23:44
-
-
Save mrjohannchang/03c78eaec5c6eccf2572c6478c5d45e7 to your computer and use it in GitHub Desktop.
Boot log
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
U-Boot 1.1.3 (Nov 15 2013 - 16:45:31) | |
Board: Ralink APSoC DRAM: 64 MB | |
relocate_code Pointer at: 83fb4000 | |
enable ephy clock...done. rf reg 29 = 5 | |
SSC disabled. | |
****************************** | |
Software System Reset Occurred | |
****************************** | |
spi_wait_nsec: 29 | |
spi device id: c2 20 17 c2 20 (2017c220) | |
find flash: MX25L6405D | |
raspi_read: from:30000 len:1000 | |
raspi_read: from:30000 len:1000 | |
============================================ | |
Ralink UBoot Version: 4.1.2.0 | |
-------------------------------------------- | |
ASIC 7620_MP (Port5<->None) | |
DRAM component: 512 Mbits DDR, width 16 | |
DRAM bus: 16 bit | |
Total memory: 64 MBytes | |
Flash component: SPI Flash | |
Date:Nov 15 2013 Time:16:45:31 | |
============================================ | |
icache: sets:512, ways:4, linesz:32 ,total:65536 | |
dcache: sets:256, ways:4, linesz:32 ,total:32768 | |
##### The CPU freq = 580 MHZ #### | |
estimate memory size =64 Mbytes | |
Please choose the operation: | |
1: Load system code to SDRAM via TFTP. | |
2: Load system code then write to Flash via TFTP. | |
3: Boot system code via Flash (default). | |
4: Entr boot command line interface. | |
7: Load Boot Loader code then write to Flash via Serial. | |
9: Load Boot Loader code then write to Flash via TFTP. | |
0 | |
3: System Boot system code via Flash. | |
## Booting image at bc050000 ... | |
raspi_read: from:50000 len:40 | |
Image Name: MIPS OpenWrt Linux-3.18.29 | |
Image Type: MIPS Linux Kernel Image (lzma compressed) | |
Data Size: 1139713 Bytes = 1.1 MB | |
Load Address: 80000000 | |
Entry Point: 80000000 | |
raspi_read: from:50040 len:116401 | |
Verifying Checksum ... OK | |
Uncompressing Kernel Image ... OK | |
No initrd | |
## Transferring control to Linux (at address 80000000) ... | |
## Giving linux memsize in MB, 64 | |
Starting kernel ... | |
[ 0.000000] Linux version 3.18.29 (changyuheng@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49363) ) #2 Tue May 31 13:33:54 PDT 2016 | |
[ 0.000000] Board has DDR2 | |
[ 0.000000] Analog PMU set to hw control | |
[ 0.000000] Digital PMU set to hw control | |
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:3 | |
[ 0.000000] bootconsole [early0] enabled | |
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) | |
[ 0.000000] MIPS: machine is Flo I2CD | |
[ 0.000000] Determined physical RAM map: | |
[ 0.000000] memory: 04000000 @ 00000000 (usable) | |
[ 0.000000] Initrd not found or empty - disabling initrd | |
[ 0.000000] Zone ranges: | |
[ 0.000000] Normal [mem 0x00000000-0x03ffffff] | |
[ 0.000000] Movable zone start for each node | |
[ 0.000000] Early memory node ranges | |
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff] | |
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] | |
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. | |
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes | |
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 | |
[ 0.000000] Kernel command line: console=ttyS1,57600 rootfstype=squashfs,jffs2 | |
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) | |
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) | |
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) | |
[ 0.000000] Writing ErrCtl register=0007e014 | |
[ 0.000000] Readback ErrCtl register=0007e014 | |
[ 0.000000] Memory: 61360K/65536K available (2517K kernel code, 130K rwdata, 516K rodata, 156K init, 186K bss, 4176K reserved) | |
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 | |
[ 0.000000] NR_IRQS:256 | |
[ 0.000000] CPU Clock: 580MHz | |
[ 0.000000] systick: running - mult: 214748, shift: 32 | |
[ 0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) | |
[ 0.070000] pid_max: default: 32768 minimum: 301 | |
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.090000] pinctrl core: initialized pinctrl subsystem | |
[ 0.100000] NET: Registered protocol family 16 | |
[ 0.440000] mt7620-pci 10140000.pcie: PCIE0 no card, disable it(RST&CLK) | |
[ 0.450000] mt7620-pci: probe of 10140000.pcie failed with error -1 | |
[ 0.470000] rt2880_gpio 10000600.gpio: registering 24 gpios | |
[ 0.480000] rt2880_gpio 10000600.gpio: registering 24 irq handlers | |
[ 0.490000] Switched to clocksource systick | |
[ 0.500000] NET: Registered protocol family 2 | |
[ 0.500000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.520000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.530000] TCP: Hash tables configured (established 1024 bind 1024) | |
[ 0.540000] TCP: reno registered | |
[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes) | |
[ 0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) | |
[ 0.570000] NET: Registered protocol family 1 | |
[ 0.580000] rt-timer 10000100.timer: maximum frequency is 2441Hz | |
[ 0.600000] futex hash table entries: 256 (order: -1, 3072 bytes) | |
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
[ 0.640000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | |
[ 0.660000] msgmni has been set to 119 | |
[ 0.670000] io scheduler noop registered | |
[ 0.670000] io scheduler deadline registered (default) | |
[ 0.680000] ralink-usb-phy usbphy: invalid resource | |
[ 0.690000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled | |
[ 0.710000] 10000500.uart: ttyS0 at MMIO 0x10000500 (irq = 13, base_baud = 2500000) is a 16550A | |
[ 0.730000] console [ttyS1] disabled | |
[ 0.730000] 10000c00.uartlite: ttyS1 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A | |
[ 0.750000] console [ttyS1] enabled | |
[ 0.750000] console [ttyS1] enabled | |
[ 0.760000] bootconsole [early0] disabled | |
[ 0.760000] bootconsole [early0] disabled | |
[ 0.790000] m25p80 spi32766.0: found mx25l6405d, expected en25q64 | |
[ 0.800000] m25p80 spi32766.0: mx25l6405d (8192 Kbytes) | |
[ 0.810000] 4 ofpart partitions found on MTD device spi32766.0 | |
[ 0.820000] Creating 4 MTD partitions on "spi32766.0": | |
[ 0.830000] 0x000000000000-0x000000030000 : "u-boot" | |
[ 0.840000] 0x000000030000-0x000000040000 : "u-boot-env" | |
[ 0.850000] 0x000000040000-0x000000050000 : "factory" | |
[ 0.860000] 0x000000050000-0x000000800000 : "firmware" | |
[ 0.940000] 2 uimage-fw partitions found on MTD device firmware | |
[ 0.950000] 0x000000050000-0x000000166441 : "kernel" | |
[ 0.960000] 0x000000166441-0x000000800000 : "rootfs" | |
[ 0.970000] mtd: device 5 (rootfs) set to be root filesystem | |
[ 0.980000] 1 squashfs-split partitions found on MTD device rootfs | |
[ 0.990000] 0x000000720000-0x000000800000 : "rootfs_data" | |
[ 1.010000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex) | |
[ 1.030000] ralink_soc_eth 10100000.ethernet: generated random MAC address 8a:fa:cb:74:9b:fa | |
[ 1.040000] libphy: mdio: probed | |
[ 1.050000] ralink_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=03a2940d, driver=Generic PHY] | |
[ 1.070000] ralink_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=0000ffff, driver=Generic PHY] | |
[ 1.100000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver | |
[ 1.110000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 | |
[ 1.120000] rt2880_wdt 10000120.watchdog: Initialized | |
[ 1.130000] TCP: cubic registered | |
[ 1.140000] NET: Registered protocol family 17 | |
[ 1.150000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. | |
[ 1.180000] 8021q: 802.1Q VLAN Support v1.8 | |
[ 1.200000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. | |
[ 1.220000] Freeing unused kernel memory: 156K (80319000 - 80340000) | |
[ 4.340000] init: Console is alive | |
[ 4.350000] init: - watchdog - | |
[ 7.730000] exFAT: Version 1.2.9 | |
[ 7.780000] MTK MSDC device init. | |
[ 7.830000] mtk-sd: MediaTek MT6575 MSDC Driver | |
[ 7.840000] sdhci: Secure Digital Host Controller Interface driver | |
[ 7.850000] sdhci: Copyright(c) Pierre Ossman | |
[ 7.860000] sdhci-pltfm: SDHCI platform and OF driver helper | |
[ 7.910000] mmc0: BKOPS_EN bit is not set | |
[ 7.930000] mmc0: new high speed MMC card at address 0001 | |
[ 7.940000] mmcblk0: mmc0:0001 OHO10C 7.28 GiB | |
[ 7.950000] mmcblk0boot0: mmc0:0001 OHO10C partition 1 4.00 MiB | |
[ 7.960000] mmcblk0boot1: mmc0:0001 OHO10C partition 2 4.00 MiB | |
[ 7.970000] mmcblk0: p1 p2 | |
[ 8.440000] init: - preinit - | |
[ 8.970000] 8021q: adding VLAN 0 to HW filter on device eth0 | |
[ 9.030000] random: mktemp urandom read with 19 bits of entropy available | |
Press the [f] key and hit [enter] to enter failsafe mode | |
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | |
[ 10.620000] ralink_soc_eth 10100000.ethernet eth0: port 4 link up (10Mbps/Half duplex) | |
[ 10.630000] ralink_soc_eth 10100000.ethernet eth0: port 5 link up (10Mbps/Half duplex) | |
[ 12.230000] mount_root: loading kmods from internal overlay | |
[ 13.490000] jffs2: notice: (330) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead. | |
[ 13.520000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab | |
[ 13.550000] block: extroot: not configured | |
[ 13.730000] jffs2: notice: (327) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead. | |
[ 14.700000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab | |
[ 14.720000] block: extroot: not configured | |
[ 14.730000] mount_root: switching to jffs2 overlay | |
[ 14.770000] procd: - early - | |
[ 14.780000] procd: - watchdog - | |
[ 15.690000] ralink_soc_eth 10100000.ethernet eth0: port 4 link down | |
[ 15.700000] ralink_soc_eth 10100000.ethernet eth0: port 5 link down | |
[ 15.820000] procd: - ubus - | |
[ 16.830000] procd: - init - | |
Please press Enter to activate this console. | |
[ 18.370000] random: nonblocking pool is initialized | |
[ 18.720000] NET: Registered protocol family 10 | |
[ 18.740000] ntfs: driver 2.1.31 [Flags: R/O MODULE]. | |
[ 18.770000] ip6_tables: (C) 2000-2006 Netfilter Core Team | |
[ 18.800000] Netfilter messages via NETLINK v0.30. | |
[ 18.810000] ip_set: protocol 6 | |
[ 19.690000] | |
[ 19.690000] | |
[ 19.690000] === pAd = c050f000, size = 649088 === | |
[ 19.690000] | |
[ 19.710000] <-- RTMPAllocTxRxRingMemory, Status=0 | |
[ 19.720000] <-- RTMPAllocAdapterBlock, Status=0 | |
[ 19.730000] AP Driver version-2.7.1.6 | |
[ 19.760000] fuse init (API version 7.23) | |
[ 19.780000] ip_tables: (C) 2000-2006 Netfilter Core Team | |
[ 19.820000] nf_conntrack version 0.5.0 (961 buckets, 3844 max) | |
[ 19.870000] xt_time: kernel timezone is -0000 | |
[ 21.280000] RX DESC a31ef000 size = 2048 | |
[ 21.290000] RTMP_TimerListAdd: add timer obj c057e020! | |
[ 21.300000] RTMP_TimerListAdd: add timer obj c054bdc8! | |
[ 21.310000] RTMP_TimerListAdd: add timer obj c054bd9c! | |
[ 21.320000] RTMP_TimerListAdd: add timer obj c054bd70! | |
[ 21.330000] RTMP_TimerListAdd: add timer obj c0554b8c! | |
[ 21.340000] RTMP_TimerListAdd: add timer obj c0554ca8! | |
[ 21.350000] RTMP_TimerListAdd: add timer obj c0554bb8! | |
[ 21.360000] RTMP_TimerListAdd: add timer obj c054c4f4! | |
[ 21.370000] RTMP_TimerListAdd: add timer obj c05144b8! | |
[ 21.380000] RTMP_TimerListAdd: add timer obj c054c204! | |
[ 21.500000] APSDCapable[0]=0 | |
[ 21.510000] APSDCapable[1]=0 | |
[ 21.510000] APSDCapable[2]=0 | |
[ 21.520000] APSDCapable[3]=0 | |
[ 21.530000] APSDCapable[4]=0 | |
[ 21.530000] APSDCapable[5]=0 | |
[ 21.540000] APSDCapable[6]=0 | |
[ 21.540000] APSDCapable[7]=0 | |
[ 21.550000] APSDCapable[8]=0 | |
[ 21.550000] APSDCapable[9]=0 | |
[ 21.560000] APSDCapable[10]=0 | |
[ 21.570000] APSDCapable[11]=0 | |
[ 21.570000] APSDCapable[12]=0 | |
[ 21.580000] APSDCapable[13]=0 | |
[ 21.580000] APSDCapable[14]=0 | |
[ 21.590000] APSDCapable[15]=0 | |
[ 21.600000] default ApCliAPSDCapable[0]=0 | |
[ 21.800000] Key1Str is Invalid key length(0) or Type(0) | |
[ 21.810000] Key2Str is Invalid key length(0) or Type(0) | |
[ 21.820000] Key3Str is Invalid key length(0) or Type(0) | |
[ 21.830000] Key4Str is Invalid key length(0) or Type(0) | |
[ 21.850000] 1. Phy Mode = 9 | |
[ 21.860000] 2. Phy Mode = 9 | |
[ 21.870000] E2PROM: D0 target power=0xff20 | |
[ 21.870000] E2PROM: 40 MW Power Delta= 0 | |
[ 21.880000] 3. Phy Mode = 9 | |
[ 21.890000] AntCfgInit: primary/secondary ant 0/1 | |
Initialize RF Central Registers for E2 !!! | |
[ 21.910000] Initialize RF Central Registers for E3 !!! | |
[ 21.920000] Initialize RF Channel Registers for E2 !!! | |
[ 21.930000] Initialize RF Channel Registers for E3 !!! | |
[ 21.940000] Initialize RF DCCal Registers for E2 !!! | |
[ 21.950000] Initialize RF DCCal Registers for E3 !!! | |
[ 21.960000] D1 = 1, D2 = 8, CalCode = 16 !!! | |
[ 21.970000] RT6352_Temperature_Init : BBPR49 = 0x1 | |
[ 21.980000] RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff7 | |
[ 21.990000] Current Temperature from BBP_R49=0xfffffffb | |
[ 22.000000] TX BW Filter Calibration !!! | |
[ 22.130000] RX BW Filter Calibration !!! | |
[ 22.360000] LOFT Calibration Done! | |
[ 22.360000] IQCalibration Start! | |
[ 22.380000] IQCalibration Done! CH = 0, (gain= f, phase=3d) | |
[ 22.390000] IQCalibration Start! | |
[ 22.410000] IQCalibration Done! CH = 1, (gain= 1, phase=3f) | |
[ 22.420000] TX IQ Calibration Done! | |
[ 22.470000] MCS Set = ff ff 00 00 00 | |
[ 22.550000] Main bssid = 00:0c:43:76:20:58 | |
[ 22.560000] <==== rt28xx_init, Status=0 | |
[ 22.570000] 0x1300 = 00064380 | |
[ 28.050000] 8021q: adding VLAN 0 to HW filter on device eth0 | |
[ 28.090000] device eth0.1 entered promiscuous mode | |
[ 28.100000] device eth0 entered promiscuous mode | |
[ 28.150000] br-lan: port 1(eth0.1) entered forwarding state | |
[ 28.160000] br-lan: port 1(eth0.1) entered forwarding state | |
[ 28.910000] ralink_soc_eth 10100000.ethernet eth0: port 4 link up (10Mbps/Half duplex) | |
[ 28.920000] ralink_soc_eth 10100000.ethernet eth0: port 5 link up (10Mbps/Half duplex) | |
[ 28.950000] RX DESC a31ef000 size = 2048 | |
[ 28.990000] RTMP_TimerListAdd: add timer obj c057e020! | |
[ 29.000000] RTMP_TimerListAdd: add timer obj c054bdc8! | |
[ 29.010000] RTMP_TimerListAdd: add timer obj c054bd9c! | |
[ 29.020000] RTMP_TimerListAdd: add timer obj c054bd70! | |
[ 29.030000] RTMP_TimerListAdd: add timer obj c0554b8c! | |
[ 29.040000] RTMP_TimerListAdd: add timer obj c0554ca8! | |
[ 29.060000] RTMP_TimerListAdd: add timer obj c0554bb8! | |
[ 29.070000] RTMP_TimerListAdd: add timer obj c054c4f4! | |
[ 29.080000] RTMP_TimerListAdd: add timer obj c05144b8! | |
[ 29.090000] RTMP_TimerListAdd: add timer obj c054c204! | |
[ 29.210000] APSDCapable[0]=0 | |
[ 29.210000] APSDCapable[1]=0 | |
[ 29.220000] APSDCapable[2]=0 | |
[ 29.220000] APSDCapable[3]=0 | |
[ 29.230000] APSDCapable[4]=0 | |
[ 29.230000] APSDCapable[5]=0 | |
[ 29.240000] APSDCapable[6]=0 | |
[ 29.250000] APSDCapable[7]=0 | |
[ 29.250000] APSDCapable[8]=0 | |
[ 29.260000] APSDCapable[9]=0 | |
[ 29.260000] APSDCapable[10]=0 | |
[ 29.270000] APSDCapable[11]=0 | |
[ 29.270000] APSDCapable[12]=0 | |
[ 29.280000] APSDCapable[13]=0 | |
[ 29.290000] APSDCapable[14]=0 | |
[ 29.290000] APSDCapable[15]=0 | |
[ 29.300000] default ApCliAPSDCapable[0]=0 | |
[ 29.310000] Key1Str is Invalid key length(0) or Type(0) | |
[ 29.320000] Key2Str is Invalid key length(0) or Type(0) | |
[ 29.330000] Key3Str is Invalid key length(0) or Type(0) | |
[ 29.340000] Key4Str is Invalid key length(0) or Type(0) | |
[ 29.370000] 1. Phy Mode = 9 | |
[ 29.370000] 2. Phy Mode = 9 | |
[ 29.380000] E2PROM: D0 target power=0xff20 | |
[ 29.390000] E2PROM: 40 MW Power Delta= 0 | |
[ 29.390000] 3. Phy Mode = 9 | |
[ 29.400000] AntCfgInit: primary/secondary ant 0/1 | |
Initialize RF Central Registers for E2 !!! | |
[ 29.420000] Initialize RF Central Registers for E3 !!! | |
[ 29.430000] Initialize RF Channel Registers for E2 !!! | |
[ 29.440000] Initialize RF Channel Registers for E3 !!! | |
[ 29.450000] Initialize RF DCCal Registers for E2 !!! | |
[ 29.460000] Initialize RF DCCal Registers for E3 !!! | |
[ 29.470000] D1 = -1, D2 = 6, CalCode = 16 !!! | |
[ 29.480000] RT6352_Temperature_Init : BBPR49 = 0xffffffff | |
[ 29.490000] RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 | |
[ 29.510000] Current Temperature from BBP_R49=0xfffffffa | |
[ 29.520000] TX BW Filter Calibration !!! | |
[ 29.640000] RX BW Filter Calibration !!! | |
[ 29.870000] LOFT Calibration Done! | |
[ 29.880000] IQCalibration Start! | |
[ 29.890000] IQCalibration Done! CH = 0, (gain= 0, phase=3f) | |
[ 29.900000] IQCalibration Start! | |
[ 29.920000] IQCalibration Done! CH = 1, (gain= f, phase=3e) | |
[ 29.930000] TX IQ Calibration Done! | |
[ 29.980000] RTMPSetPhyMode: channel is out of range, use first channel=0 | |
[ 30.000000] MCS Set = ff ff 00 00 01 | |
[ 30.040000] SYNC - BBP R4 to 20MHz.l | |
[ 30.160000] br-lan: port 1(eth0.1) entered forwarding state | |
[ 32.770000] Main bssid = 00:0c:43:76:20:58 | |
[ 32.770000] <==== rt28xx_init, Status=0 | |
[ 32.780000] 0x1300 = 00064380 | |
[ 33.510000] device ra0 entered promiscuous mode | |
[ 33.520000] br-lan: port 2(ra0) entered forwarding state | |
[ 33.530000] br-lan: port 2(ra0) entered forwarding state | |
[ 35.530000] br-lan: port 2(ra0) entered forwarding state |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment