Skip to content

Instantly share code, notes, and snippets.

@musashino205

musashino205/WG2600HP bootlog with firmware partition

Created May 11, 2018 16:58
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save musashino205/ef9330744572717aac320b7abae52649 to your computer and use it in GitHub Desktop.
Save musashino205/ef9330744572717aac320b7abae52649 to your computer and use it in GitHub Desktop.
Download ZIP
WG2600HP bootlog when unified the "kernel" and "rootfs" to firmware partition
Raw
WG2600HP bootlog with firmware partition
U-Boot 2012.07 [Standard IPQ806X.LN,local] (Mar 26 2015 - 13:53:09)
smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
NAND: ipq_nand: unknown NAND device manufacturer: 0 device: 0
ipq_nand: failed to identify device
SF: Detected S25FL256S with page size 64 KiB, total 32 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x2000000
32 MiB
MMC:
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
PRODUCTDATA CRC Verify OK.
Net: MAC1 addr:c0:25:a2:ef:1e:25
athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
MAC2 addr:c0:25:a2:ef:1e:24
eth0, eth1
post start
SF: Detected S25FL256S with page size 64 KiB, total 32 MiB
DRAM Test ..... PASS
Timer test .... PASS
FLASH CHKSUM .. PASS
LAN Test ......
LoopBack count 0 ..
PASS
Package TYPE = 0x01
post success
now booting auto ...
MMC Device 0 not found
MMC Device 0 not found
Loading from nand1, offset 0x860000
Image Name: ARM OpenWrt Linux-4.9.96
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1992060 Bytes = 1.9 MiB
Load Address: 42208000
Entry Point: 42208000
Automatic boot of image at addr 0x44000000 ...
Image Name: ARM OpenWrt Linux-4.9.96
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1992060 Bytes = 1.9 MiB
Load Address: 42208000
Entry Point: 42208000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
info: "mtdparts" not set
Using machid 0x1260 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.96 (musashino205@Taiha.Net) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r0+6893-bb6888a) ) #0 SMP Fri May 11 15:32:14 2018
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt:Machine model: NEC Aterm WG2600HP
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 13 pages/cpu @ddc07000 s20940 r8192 d24116 u53248
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line:
[ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 root=mtd:rootfs rootfstype=squashfs reboot=0 root=mtd:rootfs rootfstype=squashfs reboot=0
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 481164K/491520K available (3799K kernel code, 234K rwdata, 1208K rodata, 240K init, 240K bss, 10356K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xde800000 - 0xff800000 ( 528 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde000000 ( 480 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc05bdf78 (3800 kB)
[ 0.000000] .init : 0xc070c000 - 0xc0748000 ( 240 kB)
[ 0.000000] .data : 0xc0748000 - 0xc0782940 ( 235 kB)
[ 0.000000] .bss : 0xc0784000 - 0xc07c0268 ( 241 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns
[ 0.000006] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns
[ 0.000020] Switching to timer-based delay loop, resolution 160ns
[ 0.000203] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500)
[ 0.000223] pid_max: default: 32768 minimum: 301
[ 0.000325] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000965] CPU: Testing write buffer coherency: ok
[ 0.001252] Setting up static identity map for 0x42208280 - 0x422082d8
[ 0.004601] Brought up 2 CPUs
[ 0.004618] SMP: Total of 2 processors activated (25.00 BogoMIPS).
[ 0.004629] CPU: All CPU(s) started in SVC mode.
[ 0.016008] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0
[ 0.016208] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.016234] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.016313] pinctrl core: initialized pinctrl subsystem
[ 0.017548] NET: Registered protocol family 16
[ 0.017794] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.041400] cpuidle: using governor ladder
[ 0.072416] cpuidle: using governor menu
[ 0.074445] qcom_rpm 108000.rpm: could not find pctldev for node /soc/pinmux@800000/i2c4_pinmux, deferring probe
[ 0.114765] msm_bus_fabric_init_driver
[ 0.115875] usbcore: registered new interface driver usbfs
[ 0.115981] usbcore: registered new interface driver hub
[ 0.116070] usbcore: registered new device driver usb
[ 0.116131] pps_core: LinuxPPS API ver. 1 registered
[ 0.116144] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.116176] PTP clock support registered
[ 0.118021] clocksource: Switched to clocksource dg_timer
[ 0.121969] NET: Registered protocol family 2
[ 0.122523] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.122569] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.122621] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.122677] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.122699] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.122886] NET: Registered protocol family 1
[ 0.124398] No memory allocated for crashlog
[ 0.124787] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.131140] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.131154] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.137736] io scheduler noop registered
[ 0.137753] io scheduler deadline registered (default)
[ 0.139264] 1b500000.pci supply vdda not found, using dummy regulator
[ 0.139372] 1b500000.pci supply vdda_phy not found, using dummy regulator
[ 0.139470] 1b500000.pci supply vdda_refclk not found, using dummy regulator
[ 0.140234] OF: PCI: host bridge /soc/pci@1b500000 ranges:
[ 0.140277] OF: PCI: IO 0x0fe00000..0x0fefffff -> 0x0fe00000
[ 0.140313] OF: PCI: MEM 0x08000000..0x0fdfffff -> 0x08000000
[ 0.248500] qcom-pcie 1b500000.pci: link up
[ 0.248692] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.248716] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.248736] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff])
[ 0.248751] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.249298] PCI: bus0: Fast back to back transfers disabled
[ 0.251416] PCI: bus1: Fast back to back transfers disabled
[ 0.251768] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff]
[ 0.251793] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.251920] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.251945] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.252825] 1b700000.pci supply vdda not found, using dummy regulator
[ 0.252925] 1b700000.pci supply vdda_phy not found, using dummy regulator
[ 0.253010] 1b700000.pci supply vdda_refclk not found, using dummy regulator
[ 0.253752] OF: PCI: host bridge /soc/pci@1b700000 ranges:
[ 0.253788] OF: PCI: IO 0x31e00000..0x31efffff -> 0x31e00000
[ 0.253810] OF: PCI: MEM 0x2e000000..0x31dfffff -> 0x2e000000
[ 0.363836] qcom-pcie 1b700000.pci: link up
[ 0.364007] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.364028] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.364044] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.364509] PCI: bus0: Fast back to back transfers disabled
[ 0.366718] PCI: bus1: Fast back to back transfers disabled
[ 0.367202] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.367224] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.367353] pci 0001:00:00.0: PCI bridge to [bus 01-ff]
[ 0.367372] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.370394] L2 @ QSB rate. Forcing new rate.
[ 0.370612] L2 @ 384000 KHz
[ 0.371207] CPU0 @ 800000 KHz
[ 0.371219] CPU1 @ QSB rate. Forcing new rate.
[ 0.371347] CPU1 @ 384000 KHz
[ 0.373981] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 0.375390] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[ 0.376850] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.377735] msm_serial 16340000.serial: msm_serial: detected port #0
[ 0.377832] msm_serial 16340000.serial: uartclk = 7372800
[ 0.377913] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 167, base_baud = 460800) is a MSM
[ 0.377950] msm_serial: console setup on port #0
[ 1.093181] console [ttyMSM0] enabled
[ 1.097887] msm_serial: driver initialized
[ 1.109230] loop: module loaded
[ 1.110596] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 1.112394] m25p80 spi32766.0: s25fl256s1 (32768 Kbytes)
[ 1.118737] 15 fixed-partitions partitions found on MTD device spi32766.0
[ 1.123856] Creating 15 MTD partitions on "spi32766.0":
[ 1.130623] 0x000000000000-0x000000020000 : "SBL1"
[ 1.136669] 0x000000020000-0x000000040000 : "MIBIB"
[ 1.141661] 0x000000040000-0x000000080000 : "SBL2"
[ 1.146336] 0x000000080000-0x000000100000 : "SBL3"
[ 1.151275] 0x000000100000-0x000000110000 : "DDRCONFIG"
[ 1.155978] 0x000000110000-0x000000120000 : "SSD"
[ 1.161175] 0x000000120000-0x0000001a0000 : "TZ"
[ 1.165958] 0x0000001a0000-0x000000220000 : "RPM"
[ 1.170752] 0x000000220000-0x0000002a0000 : "APPSBL"
[ 1.175247] 0x0000002a0000-0x0000002b0000 : "APPSBLENV"
[ 1.180337] 0x0000002b0000-0x0000002e0000 : "PRODUCTDATA"
[ 1.185206] 0x0000002e0000-0x000000320000 : "ART"
[ 1.190927] 0x000000320000-0x000000360000 : "TP"
[ 1.195503] 0x000000360000-0x000000860000 : "TINY"
[ 1.200237] 0x000000860000-0x000002000000 : "firmware"
[ 1.214415] random: fast init done
[ 1.276240] no rootfs found after FIT image in "firmware"
[ 1.277115] libphy: GPIO Bitbanged MDIO: probed
[ 1.306720] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 2.218384] libphy: Fixed MDIO Bus: probed
[ 2.218417] libphy: mdio_driver_register: qca8k
[ 2.223213] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.225802] Ring mode enabled
[ 2.231081] DMA HW capability register supported[ 2.233960] Enhanced/Alternate descriptors
[ 2.239601] Enabled extended descriptors
[ 2.242560] RX Checksum Offload Engine supported
[ 2.246727] COE Type 2
[ 2.251473] TX Checksum insertion supported
[ 2.253670] Wake-Up On Lan supported
[ 2.258185] Enable RX Mitigation via HW Watchdog Timer
[ 2.263670] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 2.266778] Ring mode enabled
[ 2.272072] DMA HW capability register supported[ 2.274939] Enhanced/Alternate descriptors
[ 2.280580] Enabled extended descriptors
[ 2.283538] RX Checksum Offload Engine supported
[ 2.287705] COE Type 2
[ 2.292459] TX Checksum insertion supported
[ 2.294649] Wake-Up On Lan supported
[ 2.299238] Enable RX Mitigation via HW Watchdog Timer
[ 2.303476] i2c /dev entries driver
[ 2.308658] Calibration not found.
[ 2.311236] qcom-tsens 900000.thermal-sensor: tsens calibration failed
[ 2.315751] Speed bin: 0
[ 2.321300] PVS bin: 1
[ 2.325688] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.326124] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations
[ 2.333886] sdhci: Secure Digital Host Controller Interface driver
[ 2.340664] sdhci: Copyright(c) Pierre Ossman
[ 2.346823] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.353006] NET: Registered protocol family 10
[ 2.358484] NET: Registered protocol family 17
[ 2.361515] 8021q: 802.1Q VLAN Support v1.8
[ 2.365716] Registering SWP/SWPB emulation handler
[ 2.382279] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342
[ 2.393680] s1a: Bringing 0uV into 1050000-1050000uV
[ 2.394003] s1b: Bringing 0uV into 1050000-1050000uV
[ 2.397990] s2a: Bringing 0uV into 800000-800000uV
[ 2.403019] s2b: Bringing 0uV into 800000-800000uV
[ 2.408316] thermal thermal_zone0: failed to read out thermal zone (-110)
[ 2.413845] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
[ 2.419497] of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:1, -19
[ [ 2.436424] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 2.436446] Please append a correct "root=" boot option; here are the available partitions:
[ 2.442958] 1f00 128 mtdblock0 [ 2.451091] (driver?)
[ 2.456241] 1f01 128 mtdblock1 [ 2.457461] (driver?)
[ 2.462584] 1f02 256 mtdblock2 [ 2.463805] (driver?)
[ 2.468996] 1f03 512 mtdblock3 [ 2.470148] (driver?)
[ 2.475270] 1f04 64 mtdblock4 [ 2.476492] (driver?)
[ 2.481614] 1f05 64 mtdblock5 [ 2.482835] (driver?)
[ 2.487955] 1f06 512 mtdblock6 [ 2.489235] (driver?)
[ 2.494298] 1f07 512 mtdblock7 [ 2.495519] (driver?)
[ 2.500641] 1f08 512 mtdblock8 [ 2.501862] (driver?)
[ 2.506984] 1f09 64 mtdblock9 [ 2.508204] (driver?)
[ 2.513328] 1f0a 192 mtdblock10 [ 2.514549] (driver?)
[ 2.519758] 1f0b 256 mtdblock11 [ 2.520980] (driver?)
[ 2.526187] 1f0c 256 mtdblock12 [ 2.527407] (driver?)
[ 2.532617] 1f0d 5120 mtdblock13 [ 2.533838] (driver?)
[ 2.539098] 1f0e 24192 mtdblock14 [ 2.540267] (driver?)
[ 2.545475] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 2.546716] CPU1: stopping
[ 2.554955] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.9.96 #0
[ 2.557641] Hardware name: Generic DT based system
[ 2.563500] [<c02155d8>] (unwind_backtrace) from [<c0211fd0>] (show_stack+0x10/0x14)
[ 2.568343] [<c0211fd0>] (show_stack) from [<c0394e34>] (dump_stack+0x7c/0x9c)
[ 2.576237] [<c0394e34>] (dump_stack) from [<c021494c>] (handle_IPI+0xdc/0x184)
[ 2.583266] [<c021494c>] (handle_IPI) from [<c0209424>] (gic_handle_irq+0x80/0x8c)
[ 2.590476] [<c0209424>] (gic_handle_irq) from [<c021294c>] (__irq_svc+0x6c/0x90)
[ 2.598100] Exception stack(0xdd473f90 to 0xdd473fd8)
[ 2.605662] 3f80: 00000001 00000000 00000000 c021a480
[ 2.610713] 3fa0: ffffe000 00000000 c074afe4 00000002 00000000 c074b034 c0745a30 00000001
[ 2.618867] 3fc0: 00000000 dd473fe0 c020f574 c020f564 60000013 ffffffff
[ 2.627025] [<c021294c>] (__irq_svc) from [<c020f564>] (arch_cpu_idle+0x1c/0x38)
[ 2.633447] [<c020f564>] (arch_cpu_idle) from [<c024f68c>] (cpu_startup_entry+0x108/0x1ac)
[ 2.641080] [<c024f68c>] (cpu_startup_entry) from [<422094cc>] (0x422094cc)
[ 2.649141] Rebooting in 1 seconds..
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment