Skip to content

Instantly share code, notes, and snippets.

@n-west
Created Jan 2, 2014
Embed
What would you like to do?
A bootlog that triggers kernel panic on first attempt booting custom insulaudit distro.
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.5.7
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1786136 Bytes = 1.7 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.5.7 (nathan@commlabbuild) (gcc version 4.8.2 (GCC) ) #1 PREEMPT Wed Jan 1 19:52:13 CST 2014
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Gumstix Overo
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 130816
[ 0.000000] free_area_init_node: node 0, pgdat c03a82c4, node_mem_map c03fb000
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 129792 pages, LIFO batch:31
[ 0.000000] OMAP3630 ES1.2 (l2cache neon isp 192mhz_clk )
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129792
[ 0.000000] Kernel command line: debug console=ttyO2,115200n8 mpurate=500 vram=12M omapfb.mode=dvi:1024x768MR-16@60 omapdss.def_disp=dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 1048576 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 511MB = 511MB total
[ 0.000000] Memory: 513624k/513624k available, 10664k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0344000 (3312 kB)
[ 0.000000] .init : 0xc0344000 - 0xc036bd1c ( 160 kB)
[ 0.000000] .data : 0xc036c000 - 0xc03a8ee0 ( 244 kB)
[ 0.000000] .bss : 0xc03a8f04 - 0xc03fabcc ( 328 kB)
[ 0.000000] NR_IRQS:474
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms
[ 0.000000] OMAP clocksource: 32k_counter at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000183] Calibrating delay loop... 597.64 BogoMIPS (lpj=2334720)
[ 0.039093] pid_max: default: 4096 minimum: 301
[ 0.039306] Mount-cache hash table entries: 512
[ 0.039947] Initializing cgroup subsys debug
[ 0.039978] Initializing cgroup subsys cpuacct
[ 0.039978] Initializing cgroup subsys memory
[ 0.040039] Initializing cgroup subsys devices
[ 0.040039] Initializing cgroup subsys freezer
[ 0.040039] Initializing cgroup subsys perf_event
[ 0.040100] CPU: Testing write buffer coherency: ok
[ 0.040374] Setting up static identity map for 0x802bd8e0 - 0x802bd938
[ 0.041229] devtmpfs: initialized
[ 0.042785] ttyO2 used as console in debug mode uart2 clocks will not be gated
[ 0.045349] dummy:
[ 0.045654] NET: Registered protocol family 16
[ 0.045989] GPMC revision 5.0
[ 0.046020] gpmc: irq-20 could not claim: err -22
[ 0.047485] OMAP GPIO hardware version 2.5
[ 0.048858] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.052459] _omap_mux_get_by_name: Could not find signal uart4_rx.uart4_rx
[ 0.058227] Reprogramming SDRC clock to 400000000 Hz
[ 0.058227] dpll3_m2_clk rate change failed: -22
[ 0.059509] usbhs_omap: alias fck already exists
[ 0.066223] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.068939] Switched to new clocking rate (Crystal/Core/MPU): 26.0/400/500 MHz
[ 0.069122] OMAP DMA hardware revision 5.0
[ 0.073425] bio: create slab <bio-0> at 0
[ 0.074127] fixed-dummy:
[ 0.074218] reg-fixed-voltage reg-fixed-voltage.0: fixed-dummy supplying 0uV
[ 0.074707] usbcore: registered new interface driver usbfs
[ 0.074798] usbcore: registered new interface driver hub
[ 0.075012] usbcore: registered new device driver usb
[ 0.086059] omap_i2c omap_i2c.1: bus 1 rev1.4.0 at 2600 kHz
[ 0.088714] twl 1-0048: PIH (irq 7) chaining IRQs 320..328
[ 0.088836] twl 1-0048: power (irq 325) chaining IRQs 328..335
[ 0.089477] twl4030_gpio twl4030_gpio: gpio (irq 320) chaining IRQs 336..353
[ 0.090087] VUSB1V5: override min_uV, 1 -> 1500000
[ 0.090118] VUSB1V5: override max_uV, 2147483647 -> 1500000
[ 0.090148] VUSB1V5: 1500 mV normal standby
[ 0.090606] VUSB1V8: override min_uV, 1 -> 1800000
[ 0.090606] VUSB1V8: override max_uV, 2147483647 -> 1800000
[ 0.090637] VUSB1V8: 1800 mV normal standby
[ 0.091064] VUSB3V1: override min_uV, 1 -> 3100000
[ 0.091094] VUSB3V1: override max_uV, 2147483647 -> 3100000
[ 0.091094] VUSB3V1: 3100 mV normal standby
[ 0.092834] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.093261] vdd_mpu_iva: 600 <--> 1450 mV normal
[ 0.093719] vdd_core: 600 <--> 1450 mV normal
[ 0.094299] VMMC1: 1850 <--> 3150 mV at 3150 mV normal standby
[ 0.094848] VDVI: 1800 mV normal standby
[ 0.109497] omap_i2c omap_i2c.3: bus 3 rev1.4.0 at 400 kHz
[ 0.110168] omap-iommu omap-iommu.0: isp registered
[ 0.111114] Switching to clocksource 32k_counter
[ 0.124816] usbhs_omap usbhs_omap: xclk60mhsp2_ck set parentfailed error:-22
[ 0.125549] NET: Registered protocol family 2
[ 0.125885] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.126495] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.126983] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.127227] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.127227] TCP: reno registered
[ 0.127258] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.127288] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.127624] NET: Registered protocol family 1
[ 0.133117] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.133148] io scheduler noop registered
[ 0.133148] io scheduler deadline registered (default)
[ 0.133911] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
[ 0.134429] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
[ 0.135009] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
[ 0.786407] console [ttyO2] enabled
[ 0.790557] omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3
[ 0.807495] brd: module loaded
[ 0.815521] loop: module loaded
[ 0.820953] twl4030_madc twl4030_madc: clk disabled, enabling
[ 0.828765] smsc911x: Driver version 2008-10-21
[ 0.835479] smsc911x-mdio: probed
[ 0.839172] smsc911x smsc911x.0: eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=smsc911x-0:01, irq=-1)
[ 0.850189] smsc911x smsc911x.0: eth0: MAC Address: 00:15:c9:29:04:13
[ 0.857025] smsc911x: Driver version 2008-10-21
[ 0.862365] usbcore: registered new interface driver asix
[ 0.868133] usbcore: registered new interface driver cdc_ether
[ 0.874420] usbcore: registered new interface driver cdc_ncm
[ 0.880401] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.887420] ehci-omap.0 supply hsusb1 not found, using dummy regulator
[ 1.900360] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 1.906341] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[ 1.914276] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 1.931671] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 1.937835] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.945037] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.952636] usb usb1: Product: OMAP-EHCI Host Controller
[ 1.958251] usb usb1: Manufacturer: Linux 3.5.7 ehci_hcd
[ 1.963867] usb usb1: SerialNumber: ehci-omap.0
[ 1.969451] hub 1-0:1.0: USB hub found
[ 1.973449] hub 1-0:1.0: 3 ports detected
[ 2.002014] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 2.014038] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 2.025329] musb-hdrc: MHDRC RTL version 1.800
[ 2.030090] musb-hdrc: setup fifo_mode 4
[ 2.034240] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 2.040222] musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
[ 2.050598] i2c /dev entries driver
[ 2.055603] voltdm_scale: No voltage scale API registered for vdd_mpu_iva
[ 2.062774] platform mpu.0: omap_target: unable to scale voltage up.
[ 2.069732] cpuidle: using governor ladder
[ 2.074127] cpuidle: using governor menu
[ 2.078613] omap_hsmmc omap_hsmmc.0: Failed to get debounce clk
[ 2.084899] omap_hsmmc.0 supply vmmc_aux not found, using dummy regulator
[ 2.092559] Unable to handle kernel NULL pointer dereference at virtual address 00000014
[ 2.101013] pgd = c0004000
[ 2.103851] [00000014] *pgd=00000000
[ 2.107574] Internal error: Oops - BUG: 5 [#1] PREEMPT ARM
[ 2.113311] Modules linked in:
[ 2.116485] CPU: 0 Not tainted (3.5.7 #1)
[ 2.121032] pc : [<c02bbc20>] lr : [<c0183c38>] psr: 60000093
[ 2.121032] sp : df82dd90 ip : df82ddb8 fp : df82ddb4
[ 2.133026] r10: 60000013 r9 : 00000000 r8 : df9a2bc0
[ 2.138488] r7 : c03aaf30 r6 : df81ab80 r5 : df82c010 r4 : 00000000
[ 2.145294] r3 : 00000000 r2 : 00000000 r1 : df82ddbc r0 : 00000000
[ 2.152130] Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 2.159851] Control: 10c5387d Table: 80004019 DAC: 00000015
[ 2.165832] Process swapper (pid: 1, stack limit = 0xdf82c2f0)
[ 2.171936] Stack: (0xdf82dd90 to 0xdf82e000)
[ 2.176483] dd80: df82ddb4 df82dda0 c02bbdb0 c02bbbb4
[ 2.185028] dda0: df89b000 df89b000 df82dddc df82ddb8 c0185c30 c0183c2c 001dc130 001c3a90
[ 2.193572] ddc0: 00000001 00192d50 df99e800 001dc130 df82de04 df82dde0 c01fd8bc c0185b94
[ 2.202117] dde0: fa002000 df99ea40 df9a2bc0 00000007 00000001 df857608 df82de2c df82de08
[ 2.210662] de00: c020deb0 c01fd820 df8550c0 00000050 df857608 df857600 df99ea40 c020de24
[ 2.219207] de20: df82de74 df82de30 c02b705c c020de30 df9a83c0 df99ea40 00000001 df9a8400
[ 2.227752] de40: c03a8f40 00000000 df82de64 df857608 df85763c c03f80fc c03a2494 c03a8f40
[ 2.236297] de60: 00000000 df82c038 df82de84 df82de78 c01ae8e8 c02b6974 df82dea4 df82de88
[ 2.244842] de80: c01ad6d8 c01ae8d8 df857608 df85763c c03a2494 c039fd58 df82dec4 df82dea8
[ 2.253387] dea0: c01ad8cc c01ad63c c01ad85c 00000000 c03a2494 c01ad85c df82deec df82dec8
[ 2.261932] dec0: c01abd00 c01ad868 df8087d8 df871df0 c015ced0 c03a2494 df9a9bc0 00000000
[ 2.270477] dee0: df82defc df82def0 c01ad234 c01abc98 df82df2c df82df00 c01ace08 c01ad220
[ 2.279022] df00: c030142e c035e2cc df82df2c c03a2494 c0364af4 c036ba1c c035e2cc c03a8f40
[ 2.287567] df20: df82df54 df82df30 c01ade44 c01acd30 00000000 00000006 c0364af4 c036ba1c
[ 2.296112] df40: c035e2cc c03a8f40 df82df64 df82df58 c01aedc8 c01addbc df82df74 df82df68
[ 2.304656] df60: c035e2e0 c01aed88 df82dfb4 df82df78 c00086f4 c035e2d8 00000006 00000006
[ 2.313201] df80: 00000049 c03434fc c004d614 00000006 c0364af4 c036ba1c c03a8f40 c03a8f40
[ 2.321746] dfa0: 00000049 00000000 df82dff4 df82dfb8 c03449c8 c0008668 00000006 00000006
[ 2.330291] dfc0: c0344264 c034483c c0032424 00000013 00000000 c034483c c0032424 00000013
[ 2.338836] dfe0: 00000000 00000000 00000000 df82dff8 c0032424 c0344848 40014424 00004400
[ 2.347381] Backtrace:
[ 2.349914] Function entered at [<c0183c20>] from [<c0185c30>]
[ 2.356018] r4:df89b000
[ 2.358642] Function entered at [<c0185b88>] from [<c01fd8bc>]
[ 2.364746] r7:001dc130 r6:df99e800 r5:00192d50 r4:00000001
[ 2.370666] Function entered at [<c01fd814>] from [<c020deb0>]
[ 2.376770] r8:df857608 r7:00000001 r6:00000007 r5:df9a2bc0 r4:df99ea40
r3:fa002000
[ 2.384948] Function entered at [<c020de24>] from [<c02b705c>]
[ 2.391052] r9:c020de24 r8:df99ea40$X������� ttyO���
[ 2.487609] r6:df857608 r5:00000050
r4:df8550c0
[ 2.492523] Function entered at [<c02b6968>] from [<c01ae8e8>]
[ 2.498626] Function entered at [<c01ae8cc>] from [<c01ad6d8>]
[ 2.504730] Function entered at [<c01ad630>] from [<c01ad8cc>]
[ 2.510803] r7:c039fd58 r6:c03a2494 r5:df85763c r4:df857608
[ 2.516723] Function entered at [<c01ad85c>] from [<c01abd00>]
[ 2.522827] r6:c01ad85c r5:c03a2494 r4:00000000 r3:c01ad85c
[ 2.528747] Function entered at [<c01abc8c>] from [<c01ad234>]
[ 2.534820] r6:00000000 r5:df9a9bc0 r4:c03a2494
[ 2.539642] Function entered at [<c01ad214>] from [<c01ace08>]
[ 2.545745] Function entered at [<c01acd24>] from [<c01ade44>]
[ 2.551818] r8:c03a8f40 r7:c035e2cc r6:c036ba1c r5:c0364af4 r4:c03a2494
[ 2.558837] Function entered at [<c01addb0>] from [<c01aedc8>]
[ 2.564941] r8:c03a8f40 r7:c035e2cc r6:c036ba1c r5:c0364af4 r4:00000006
r3:00000000
[ 2.573150] Function entered at [<c01aed7c>] from [<c035e2e0>]
[ 2.579223] Function entered at [<c035e2cc>] from [<c00086f4>]
[ 2.585327] Function entered at [<c000865c>] from [<c03449c8>]
[ 2.591400] Function entered at [<c034483c>] from [<c0032424>]
[ 2.597503] r9:00000000 r8:00000000 r7:00000013 r6:c0032424 r5:c034483c
r4:00000000
[ 2.605712] Code: f10c0080 e5972000 e3520000 1a000003 (e5942014)
[ 2.612121] ---[ end trace 55bf8497fc26d3c6 ]---
[ 2.616943] note: swapper[1] exited with preempt_count 1
[ 2.622528] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 2.622528]
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment