Created
April 6, 2017 14:36
-
-
Save nebbian/c28abcd39053342671e9e1030bece50c to your computer and use it in GitHub Desktop.
Configuration for Delta mini on Re-Arm
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # Smoothieboard configuration file, see http://smoothieware.org/configuring-smoothie | |
| # NOTE Lines must not exceed 132 characters, and '#' characters mean what follows is ignored | |
| ## Robot module configurations : general handling of movement G-codes and slicing into moves | |
| # Basic motion configuration | |
| default_feed_rate 4000 # Default speed (mm/minute) for G1/G2/G3 moves | |
| default_seek_rate 4000 # Default speed (mm/minute) for G0 moves | |
| mm_per_arc_segment 0.0 # Fixed length for line segments that divide arcs, 0 to disable | |
| #mm_per_line_segment 5 # Cut lines into segments this size | |
| mm_max_arc_error 0.01 # The maximum error for line segments that divide arcs 0 to disable | |
| # note it is invalid for both the above be 0 | |
| # if both are used, will use largest segment length based on radius | |
| delta_segments_per_second 100 # For deltas only, number of segments per second, set to 0 to disable | |
| # and use mm_per_line_segment | |
| # Arm solution configuration : Cartesian robot. Translates mm positions into stepper positions | |
| # See http://smoothieware.org/stepper-motors | |
| alpha_steps_per_mm 640 # Steps per mm for alpha ( X ) stepper and tower | |
| beta_steps_per_mm 640 # Steps per mm for beta ( Y ) stepper and tower | |
| gamma_steps_per_mm 640 # Steps per mm for gamma ( Z ) stepper and tower | |
| # Delta configuration | |
| # See http://smoothieware.org/delta | |
| arm_solution linear_delta # Selects the linear delta arm solution | |
| arm_length 217.8 # This is the length of an arm from hinge to hinge | |
| arm_radius 112.41 # This is the horizontal distance from hinge to hinge when the effector is centered | |
| # Endstop trim options | |
| alpha_trim -3.158 # Software trim for alpha stepper endstop (in mm) | |
| beta_trim -2.154 # Software trim for beta stepper endstop (in mm) | |
| gamma_trim 0 # Software trim for gamma stepper endstop (in mm) | |
| delta_tower1_angle -0.23 # Angle offset for tower 1 (alpha) | |
| delta_tower2_angle -0.25 # Angle offset for tower 2 (beta) | |
| delta_tower3_angle 0.0 # Angle offset for tower 3 (gamma) | |
| # Planner module configuration : Look-ahead and acceleration configuration | |
| # See http://smoothieware.org/motion-control | |
| acceleration 3000 # Acceleration in mm/second/second. | |
| #z_acceleration 500 # Acceleration for Z only moves in mm/s^2, 0 uses acceleration which is the default. DO NOT SET ON A DELTA | |
| junction_deviation 0.05 # See http://smoothieware.org/motion-control#junction-deviation | |
| #z_junction_deviation 0.0 # For Z only moves, -1 uses junction_deviation, zero disables junction_deviation on z moves DO NOT SET ON A DELTA | |
| # Cartesian axis speed limits | |
| x_axis_max_speed 30000 # Maximum speed in mm/min | |
| y_axis_max_speed 30000 # Maximum speed in mm/min | |
| z_axis_max_speed 30000 # Maximum speed in mm/min | |
| # Stepper module configuration | |
| # Pins are defined as ports, and pin numbers, appending "!" to the number will invert a pin | |
| # See http://smoothieware.org/pin-configuration and http://smoothieware.org/pinout | |
| alpha_step_pin 2.1 # Pin for alpha stepper step signal | |
| alpha_dir_pin 0.11! # Pin for alpha stepper direction, add '!' to reverse direction | |
| alpha_en_pin 0.10 # Pin for alpha enable pin | |
| alpha_current 1.5 # X stepper motor current | |
| alpha_max_rate 30000.0 # Maximum rate in mm/min | |
| beta_step_pin 2.2 # Pin for beta stepper step signal | |
| beta_dir_pin 0.20! # Pin for beta stepper direction, add '!' to reverse direction | |
| beta_en_pin 0.19 # Pin for beta enable | |
| beta_current 1.5 # Y stepper motor current | |
| beta_max_rate 30000.0 # Maxmimum rate in mm/min | |
| gamma_step_pin 2.3 # Pin for gamma stepper step signal | |
| gamma_dir_pin 0.22! # Pin for gamma stepper direction, add '!' to reverse direction | |
| gamma_en_pin 0.21 # Pin for gamma enable | |
| gamma_current 1.5 # Z stepper motor current | |
| gamma_max_rate 30000.0 # Maximum rate in mm/min | |
| ## Extruder module configuration | |
| # See http://smoothieware.org/extruder | |
| extruder.hotend.enable true # Whether to activate the extruder module at all. All configuration is ignored if false | |
| extruder.hotend.steps_per_mm 418.5 # Steps per mm for extruder stepper | |
| extruder.hotend.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves | |
| extruder.hotend.acceleration 500 # Acceleration for the stepper motor mm/sec² | |
| extruder.hotend.max_speed 50 # Maximum speed in mm/s | |
| extruder.hotend.step_pin 2.0 # Pin for extruder step signal | |
| extruder.hotend.dir_pin 0.5! # Pin for extruder dir signal ( add '!' to reverse direction ) | |
| extruder.hotend.en_pin 0.4 # Pin for extruder enable signal | |
| # Extruder offset | |
| #extruder.hotend.x_offset 0 # X offset from origin in mm | |
| #extruder.hotend.y_offset 0 # Y offset from origin in mm | |
| #extruder.hotend.z_offset 0 # Z offset from origin in mm | |
| # Firmware retract settings when using G10/G11, these are the defaults if not defined, must be defined for each extruder if not using the defaults | |
| #extruder.hotend.retract_length 3 # Retract length in mm | |
| #extruder.hotend.retract_feedrate 45 # Retract feedrate in mm/sec | |
| #extruder.hotend.retract_recover_length 0 # Additional length for recover | |
| #extruder.hotend.retract_recover_feedrate 8 # Recover feedrate in mm/sec (should be less than retract feedrate) | |
| #extruder.hotend.retract_zlift_length 0 # Z-lift on retract in mm, 0 disables | |
| #extruder.hotend.retract_zlift_feedrate 6000 # Z-lift feedrate in mm/min (Note mm/min NOT mm/sec) | |
| delta_current 1.5 # First extruder stepper motor current | |
| # Second extruder module configuration | |
| #extruder.hotend2.enable true # Whether to activate the extruder module at all. All configuration is ignored if false | |
| #extruder.hotend2.steps_per_mm 140 # Steps per mm for extruder stepper | |
| #extruder.hotend2.default_feed_rate 600 # Default rate ( mm/minute ) for moves where only the extruder moves | |
| #extruder.hotend2.acceleration 500 # Acceleration for the stepper motor, as of 0.6, arbitrary ratio | |
| #extruder.hotend2.max_speed 50 # mm/s | |
| #extruder.hotend2.step_pin 2.8 # Pin for extruder step signal | |
| #extruder.hotend2.dir_pin 2.13 # Pin for extruder dir signal ( add '!' to reverse direction ) | |
| #extruder.hotend2.en_pin 4.29 # Pin for extruder enable signal | |
| #extruder.hotend2.x_offset 0 # x offset from origin in mm | |
| #extruder.hotend2.y_offset 25.0 # y offset from origin in mm | |
| #extruder.hotend2.z_offset 0 # z offset from origin in mm | |
| #epsilon_current 1.5 # Second extruder stepper motor current | |
| ## Laser module configuration | |
| # See http://smoothieware.org/laser | |
| laser_module_enable false # Whether to activate the laser module at all | |
| laser_module_pwm_pin 2.7 # This pin will be PWMed to control the laser. | |
| # Only pins 2.0, 2.1, 2.2, 2.3, 2.4, 2.5, 1.18, 1.20, 1.21, 1.23, 1.24, 1.26, 3.25 and 3.26 | |
| # can be used since laser requires hardware PWM, see http://smoothieware.org/pinout | |
| #laser_module_ttl_pin 1.30 # This pin turns on when the laser turns on, and off when the laser turns off. | |
| #laser_module_maximum_power 1.0 # This is the maximum duty cycle that will be applied to the laser | |
| #laser_module_minimum_power 0.0 # This is a value just below the minimum duty cycle that keeps the laser | |
| # active without actually burning. | |
| #laser_module_default_power 0.8 # This is the default laser power that will be used for cuts if a power has not been specified. The value is a scale between | |
| # the maximum and minimum power levels specified above | |
| #laser_module_pwm_period 20 # This sets the pwm frequency as the period in microseconds | |
| ## Temperature control configuration | |
| # See http://smoothieware.org/temperaturecontrol | |
| # First hotend configuration | |
| temperature_control.hotend.enable true # Whether to activate this ( "hotend" ) module at all. | |
| temperature_control.hotend.thermistor_pin 0.23 # Pin for the thermistor to read | |
| temperature_control.hotend.heater_pin 2.5 # Pin that controls the heater, set to nc if a readonly thermistor is being defined | |
| temperature_control.hotend.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#toc5 | |
| #temperature_control.hotend.beta 4066 # Or set the beta value | |
| temperature_control.hotend.set_m_code 104 # M-code to set the temperature for this module | |
| temperature_control.hotend.set_and_wait_m_code 109 # M-code to set-and-wait for this module | |
| temperature_control.hotend.designator T # Designator letter for this module | |
| #temperature_control.hotend.max_temp 270 # Set maximum temperature - Will prevent heating above 300 by default | |
| #temperature_control.hotend.min_temp 0 # Set minimum temperature - Will prevent heating below if set | |
| # Safety control is enabled by default and can be overidden here, the values show the defaults | |
| # See http://smoothieware.org/temperaturecontrol#runaway | |
| #temperature_control.hotend.runaway_heating_timeout 900 # How long it can take to heat up, max is 2040 seconds. | |
| temperature_control.hotend.runaway_cooling_timeout 40 # How long it can take to cool down if temp is set lower, max is 2040 seconds | |
| #temperature_control.hotend.runaway_range 20 # How far from the set temperature it can wander, max setting is 63°C | |
| # PID configuration | |
| # See http://smoothieware.org/temperaturecontrol#pid | |
| temperature_control.hotend.p_factor 46.3 # P ( proportional ) factor | |
| temperature_control.hotend.i_factor 3.402 # I ( integral ) factor | |
| temperature_control.hotend.d_factor 157 # D ( derivative ) factor | |
| #temperature_control.hotend.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v. | |
| # Second hotend configuration | |
| #temperature_control.hotend2.enable true # Whether to activate this ( "hotend" ) module at all. | |
| #temperature_control.hotend2.thermistor_pin 0.25 # Pin for the thermistor to read | |
| #temperature_control.hotend2.heater_pin 1.23 # Pin that controls the heater | |
| #temperature_control.hotend2.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor | |
| ##temperature_control.hotend2.beta 4066 # or set the beta value | |
| #temperature_control.hotend2.set_m_code 104 # M-code to set the temperature for this module | |
| #temperature_control.hotend2.set_and_wait_m_code 109 # M-code to set-and-wait for this module | |
| #temperature_control.hotend2.designator T1 # Designator letter for this module | |
| #temperature_control.hotend2.p_factor 13.7 # P ( proportional ) factor | |
| #temperature_control.hotend2.i_factor 0.097 # I ( integral ) factor | |
| #temperature_control.hotend2.d_factor 24 # D ( derivative ) factor | |
| #temperature_control.hotend2.max_pwm 64 # Max pwm, 64 is a good value if driving a 12v resistor with 24v. | |
| temperature_control.bed.enable true # Whether to activate this ( "hotend" ) module at all. | |
| temperature_control.bed.thermistor_pin 0.24 # Pin for the thermistor to read | |
| temperature_control.bed.heater_pin 2.7 # Pin that controls the heater | |
| temperature_control.bed.thermistor EPCOS100K # See http://smoothieware.org/temperaturecontrol#thermistor | |
| #temperature_control.bed.beta 3974 # Or set the beta value | |
| temperature_control.bed.set_m_code 140 # M-code to set the temperature for this module | |
| temperature_control.bed.set_and_wait_m_code 190 # M-code to set-and-wait for this module | |
| temperature_control.bed.designator B # Designator letter for this module | |
| temperature_control.bed.pwm_frequency 1 # PWM frequency for the bed | |
| temperature_control.bed.p_factor 100 # P ( proportional ) factor | |
| temperature_control.bed.i_factor 5 # I ( integral ) factor | |
| temperature_control.bed.i_max 70 # Max I clamp | |
| temperature_control.bed.d_factor 100 # D ( derivative ) factor | |
| temperature_control.bed.max_pwm 255 | |
| # Bang-bang ( simplified ) control | |
| # See http://smoothieware.org/temperaturecontrol#bang-bang | |
| #temperature_control.bed.bang_bang true # Set to true to use bang bang control rather than PID | |
| #temperature_control.bed.hysteresis 0.5 # Set to the temperature in degrees C to use as hysteresis | |
| ## Switch modules | |
| # See http://smoothieware.org/switch | |
| # Switch module for fan control | |
| switch.fan.enable true # Enable this module | |
| switch.fan.input_on_command M106 # Command that will turn this switch on | |
| switch.fan.input_off_command M107 # Command that will turn this switch off | |
| switch.fan.output_pin 2.4 # Pin this module controls | |
| switch.fan.output_type pwm # PWM output settable with S parameter in the input_on_comand | |
| #switch.fan.max_pwm 255 # Set max pwm for the pin default is 255 | |
| #switch.misc.enable true # Enable this module | |
| #switch.misc.input_on_command M42 # Command that will turn this switch on | |
| #switch.misc.input_off_command M43 # Command that will turn this switch off | |
| #switch.misc.output_pin 2.4 # Pin this module controls | |
| #switch.misc.output_type digital # Digital means this is just an on or off pin | |
| switch.servo1.enable true # Enable servo1 | |
| switch.servo1.output_pin 1.20 # SER1 pin | |
| switch.servo1.output_type hwpwm # PWM output | |
| switch.servo1.startup_value 0 # Start with servo disabled | |
| switch.servo1.max_pwm 100 # Max PWM | |
| switch.servo1.pwm_period_ms 20 # PWM period | |
| switch.servo1.input_on_command M280 # G code to set PWM period. M280 S5 is full one direction, S7.5 would be midway, S10 is the other extreme. | |
| switch.servo1.input_off_command M280 # G code to set PWM period | |
| switch.servo1.fail_safe_set_to 0 | |
| ## Temperatureswitch | |
| # See http://smoothieware.org/temperatureswitch | |
| # Automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes | |
| # Useful to turn on a fan or water pump to cool the hotend | |
| #temperatureswitch.hotend.enable true # | |
| #temperatureswitch.hotend.designator T # first character of the temperature control designator to use as the temperature sensor to monitor | |
| #temperatureswitch.hotend.switch misc # select which switch to use, matches the name of the defined switch | |
| #temperatureswitch.hotend.threshold_temp 60.0 # temperature to turn on (if rising) or off the switch | |
| #temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals | |
| #temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals | |
| ## Endstops | |
| # See http://smoothieware.org/endstops | |
| endstops_enable true # The endstop module is enabled by default and can be disabled here | |
| delta_homing true # Forces all three axis to home a the same time regardless of what is specified in G28 | |
| alpha_min_endstop nc #1.24!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground | |
| alpha_max_endstop 1.25!^ # Pin to read max endstop, uncomment this and comment the above if using max endstops | |
| alpha_homing_direction home_to_max # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop | |
| alpha_max 0 # This gets loaded as the current position after homing when home_to_max is set | |
| beta_min_endstop nc #1.26!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground | |
| beta_max_endstop 1.27!^ # Pin to read max endstop, uncomment this and comment the above if using max endstops | |
| beta_homing_direction home_to_max # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop | |
| beta_max 0 # This gets loaded as the current position after homing when home_to_max is set | |
| gamma_min_endstop nc #1.29!^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground | |
| gamma_max_endstop 1.28!^ # Pin to read max endstop, uncomment this and comment the above if using max endstops | |
| gamma_homing_direction home_to_max # Or set to home_to_max and set alpha_max and uncomment the alpha_max_endstop | |
| gamma_max 218.24 # This gets loaded as the current position after homing when home_to_max is set | |
| # For 161 steps/mm, use 216.88 as gamma max. For 160 steps/mm use 218.24 | |
| alpha_max_travel 1000 # Max travel in mm for alpha/X axis when homing | |
| beta_max_travel 1000 # Max travel in mm for beta/Y axis when homing | |
| gamma_max_travel 1000 # Max travel in mm for gamma/Z axis when homing | |
| # Endstops home at their fast feedrate first, then once the endstop is found they home again at their slow feedrate for accuracy | |
| alpha_fast_homing_rate_mm_s 70 # Alpha tower fast homing feedrate in mm/second | |
| alpha_slow_homing_rate_mm_s 10 # Alpha tower slow homing feedrate in mm/second | |
| beta_fast_homing_rate_mm_s 70 # Beta tower fast homing feedrate in mm/second | |
| beta_slow_homing_rate_mm_s 10 # Beta tower slow homing feedrate in mm/second | |
| gamma_fast_homing_rate_mm_s 70 # Gamma tower fast homing feedrate in mm/second | |
| gamma_slow_homing_rate_mm_s 10 # Gamma tower slow homing feedrate in mm/second | |
| alpha_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for alpha/X | |
| beta_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for beta/Y | |
| gamma_homing_retract_mm 5 # Distance to retract from the endstop after it is hit for gamma/Z | |
| # Endstop debouncing options | |
| #endstop_debounce_count 100 # Uncomment if you get noise on your endstops, default is 100 | |
| #endstop_debounce_ms 1 # Uncomment if you get noise on your endstops, default is 1 millisecond debounce | |
| # End of endstop config | |
| # Delete the above endstop section and uncomment next line and copy and edit Snippets/abc-endstop.config file to enable endstops for ABC axis | |
| #include abc-endstop.config | |
| ## Z-probe | |
| # See http://smoothieware.org/zprobe | |
| zprobe.enable true # Set to true to enable a zprobe | |
| zprobe.probe_pin 1.29^ # Pin probe is attached to, if NC remove the ! | |
| zprobe.slow_feedrate 5 # Mm/sec probe feed rate | |
| #zprobe.debounce_count 100 # Set if noisy | |
| zprobe.fast_feedrate 70 # Move feedrate mm/sec | |
| zprobe.probe_height 15 # How much above bed to start probe | |
| #gamma_min_endstop nc # Normally 1.28. Change to nc to prevent conflict, | |
| # Levelling strategy | |
| # Example for the delta calibration strategy | |
| leveling-strategy.delta-calibration.enable true # Enable basic delta calibration | |
| leveling-strategy.delta-calibration.radius 85 # the probe radius | |
| leveling-strategy.delta-calibration.initial_height 20 # Height to stop the initial fast move down | |
| # Example for the delta grid leveling strategy | |
| leveling-strategy.delta-grid.enable true # Enable grid leveling | |
| leveling-strategy.delta-grid.radius 90 # Grid radius in millimeters | |
| leveling-strategy.delta-grid.size 7 # Grid size, must be an odd number | |
| leveling-strategy.delta-grid.do_home true # Whether to home before calibration | |
| leveling-strategy.delta-grid.save true # Whether to automatically save the grid | |
| leveling-strategy.delta-grid.initial_height 20 # Height at which to start probling | |
| # Panel | |
| # See http://smoothieware.org/panel | |
| panel.enable true # set to true to enable the panel code | |
| # Reprap discount GLCD with ribbon cables, and 5V broken out | |
| panel.lcd reprap_discount_glcd # set type of panel | |
| panel.spi_channel 0 # set spi channel to use P0_18,P0_15 MOSI,SCLK | |
| panel.spi_cs_pin 0.16 # set spi chip select | |
| panel.encoder_a_pin 3.25!^ # encoder pin | |
| panel.encoder_b_pin 3.26!^ # encoder pin | |
| panel.click_button_pin 2.11!^ # click button | |
| panel.encoder_resolution 4 # override number of clicks to move 1 item (default is 4) | |
| #panel.button_pause_pin 1.22!^ # kill/pause set one of these for the auxilliary button on viki2 | |
| #panel.back_button_pin 1.22!^ # back button recommended to use this on EXP1 | |
| panel.buzz_pin 1.30 # pin for buzzer on EXP2 | |
| panel.external_sd true # set to true if there is an extrernal sdcard on the panel | |
| panel.external_sd.spi_channel 0 # set spi channel the sdcard is on | |
| panel.external_sd.spi_cs_pin 1.23 # set spi chip select for the sdcard | |
| panel.external_sd.sdcd_pin 1.31!^ # sd detect signal (set to nc if no sdcard detect) | |
| panel.menu_offset 1 # some panels will need 1 here | |
| # Example for reprap discount GLCD | |
| # on glcd EXP1 is to left and EXP2 is to right, pin 1 is bottom left, pin 2 is top left etc. | |
| # +5v is EXP1 pin 10, Gnd is EXP1 pin 9 | |
| #panel.lcd reprap_discount_glcd # | |
| #panel.spi_channel 0 # SPI channel to use ; GLCD EXP1 Pins 3,5 (MOSI, SCLK) | |
| #panel.spi_cs_pin 0.16 # SPI chip select ; GLCD EXP1 Pin 4 | |
| #panel.encoder_a_pin 3.25!^ # Encoder pin ; GLCD EXP2 Pin 3 | |
| #panel.encoder_b_pin 3.26!^ # Encoder pin ; GLCD EXP2 Pin 5 | |
| #panel.click_button_pin 1.30!^ # Click button ; GLCD EXP1 Pin 2 | |
| #panel.buzz_pin 1.31 # Pin for buzzer ; GLCD EXP1 Pin 1 | |
| #panel.back_button_pin 2.11!^ # Back button ; GLCD EXP2 Pin 8 | |
| panel.alpha_jog_feedrate 6000 # X jogging feedrate in mm/min | |
| panel.beta_jog_feedrate 6000 # Y jogging feedrate in mm/min | |
| panel.gamma_jog_feedrate 6000 # Z jogging feedrate in mm/min | |
| panel.hotend_temperature 195 # Temp to set hotend when preheat is selected | |
| panel.bed_temperature 65 # Temp to set bed when preheat is selected | |
| ## Custom menus : Example of a custom menu entry, which will show up in the Custom entry. | |
| # NOTE _ gets converted to space in the menu and commands, | is used to separate multiple commands | |
| custom_menu.power_on.enable true # | |
| custom_menu.power_on.name Power_on # | |
| custom_menu.power_on.command M80 # | |
| custom_menu.power_off.enable true # | |
| custom_menu.power_off.name Power_off # | |
| custom_menu.power_off.command M81 # | |
| custom_menu.probe_retract.enable true # | |
| custom_menu.probe_retract.name Probe_retract # | |
| custom_menu.probe_retract.command M280_S10 # | |
| custom_menu.probe_deploy.enable true # | |
| custom_menu.probe_deploy.name Probe_deploy # | |
| custom_menu.probe_deploy.command M280_S4 # | |
| custom_menu.calibrate_delta.enable true # | |
| custom_menu.calibrate_delta.name Calibrate_delta # | |
| custom_menu.calibrate_delta.command M280_S4|G28|G32|M280_S10|G28 # | |
| custom_menu.set_z_zero.enable true # | |
| custom_menu.set_z_zero.name Set_Z_0 # | |
| custom_menu.set_z_zero.command M665_Z0 # | |
| custom_menu.save_settings.enable true # | |
| custom_menu.save_settings.name Save_settings # | |
| custom_menu.save_settings.command M500 # | |
| # RE-ARM specific settings do not change | |
| currentcontrol_module_enable false # | |
| digipot_max_current 2.4 # max current | |
| digipot_factor 106.0 # factor for converting current to digipot value | |
| leds_disable true # disable using leds after config loaded | |
| # network settings | |
| network.enable false # enable the ethernet network services | |
| network.webserver.enable true # enable the webserver | |
| network.telnet.enable true # enable the telnet server | |
| network.plan9.enable true # enable the plan9 network filesystem | |
| network.ip_address 10.0.1.100 # the IP address | |
| network.ip_mask 255.255.255.0 # the ip mask | |
| network.ip_gateway 10.0.1.60 # the gateway address | |
| #network.mac_override xx.xx.xx.xx.xx.xx # Override the mac address, only do this if you have a conflict | |
| ## System configuration | |
| # Serial communications configuration ( baud rate defaults to 9600 if undefined ) | |
| # For communication over the UART port, *not* the USB/Serial port | |
| uart0.baud_rate 115200 # Baud rate for the default hardware ( UART ) serial port | |
| second_usb_serial_enable false # This enables a second USB serial port | |
| #leds_disable true # Disable using leds after config loaded | |
| #play_led_disable true # Disable the play led | |
| # Kill button maybe assigned to a different pin, set to the onboard pin by default | |
| # See http://smoothieware.org/killbutton | |
| kill_button_enable true # Set to true to enable a kill button | |
| kill_button_pin 1.22!^ # Kill button pin. default is same as pause button 2.12 (2.11 is another good choice) | |
| #msd_disable false # Disable the MSD (USB SDCARD), see http://smoothieware.org/troubleshooting#disable-msd | |
| #dfu_enable false # For linux developers, set to true to enable DFU | |
| # Only needed on a smoothieboard | |
| # See http://smoothieware.org/currentcontrol | |
| currentcontrol_module_enable true # Control stepper motor current via the configuration file |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment