12d1:14dc Huawei Technologies Co., Ltd. E33372 LTE/UMTS/GSM HiLink Modem/Networkcard, Huawei Technologies Co., Ltd. E353/E3131 (Mass storage mode)

gistfile1.txt

sudo usb_modeswitch -v 12d1 -p 1f01 -V 12d1 -P 14DC -J 

# Bus 001 Device 028: ID 12d1:14dc Huawei Technologies Co., Ltd. E33372 LTE/UMTS/GSM HiLink Modem/Networkcard
# Bus 001 Device 027: ID 12d1:1f01 Huawei Technologies Co., Ltd. E353/E3131 (Mass storage mode)

sudo usb_modeswitch -h                                                                                                                                                     15s  Thu 23 Nov 2017 00:13:05 SAST

 * usb_modeswitch: handle USB devices with multiple modes
 * Version 2.5.1 (C) Josua Dietze 2017
 * Based on libusb1/libusbx

 ! PLEASE REPORT NEW CONFIGURATIONS !


Usage: usb_modeswitch [<params>] [-c filename]

 -h, --help                    this help
 -e, --version                 print version information and exit
 -j, --find-mbim               return config no. with MBIM interface, exit

 -v, --default-vendor NUM      vendor ID of original mode (mandatory)
 -p, --default-product NUM     product ID of original mode (mandatory)
 -V, --target-vendor NUM       target mode vendor ID (optional)
 -P, --target-product NUM      target mode product ID (optional)
 -C, --target-class NUM        target mode device class (optional)
 -b, --bus-num NUM             system bus number of device (for hard ID)
 -g, --device-num NUM          system device number (for hard ID)
 -m, --message-endpoint NUM    direct the message transfer there (optional)
 -M, --message-content <msg>   message to send (hex number as string)
 -2 <msg>, -3 <msg>            additional messages to send (-n recommended)
 -w, --release-delay NUM       wait NUM ms before releasing the interface
 -n, --need-response           obsolete, no effect (always on)
 -r, --response-endpoint NUM   read response from there (optional)
 -K, --std-eject               send standard EJECT sequence
 -d, --detach-only             detach the active driver, no further action
 -H, --huawei-mode             apply a special procedure
 -J, --huawei-new-mode         apply a special procedure
 -X, --huawei-alt-mode         apply a special procedure
 -S, --sierra-mode             apply a special procedure
 -O, --sony-mode               apply a special procedure
 -G, --gct-mode                apply a special procedure
 -N, --sequans-mode            apply a special procedure
 -A, --mobileaction-mode       apply a special procedure
 -T, --kobil-mode              apply a special procedure
 -L, --cisco-mode              apply a special procedure
 -B, --qisda-mode              apply a special procedure
 -E, --quanta-mode             apply a special procedure
 -F, --pantech-mode NUM        apply a special procedure, pass NUM through
 -Z, --blackberry-mode         apply a special procedure
 -U, --option-mode             apply a special procedure
 -R, --reset-usb               reset the device after all other actions
 -Q, --quiet                   don't show progress or error messages
 -W, --verbose                 print all settings and debug output
 -D, --sysmode                 specific result and syslog message
 -s, --success <seconds>       switching result check with timeout
 -I, --inquire                 obsolete, no effect

 -c, --config-file <filename>  load long configuration from file

 -t, --stdinput                read long configuration from stdin

 -f, --long-config <text>      get long configuration from string

 -i, --interface NUM           select initial USB interface (default 0)
 -u, --configuration NUM       select USB configuration
 -a, --altsetting NUM          select alternative USB interface setting