Last active
December 30, 2015 06:18
-
-
Save nullnilaki/7788109 to your computer and use it in GitHub Desktop.
OpenBSD/sgi TEZRO log
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sgi TEZRO | |
001c01-L1>power up | |
returning to console mode 001c01 CPU0, <CTRL_T> to escape to L1 | |
Starting PROM Boot process | |
WARNING: xbow_base: 0x9200000000000000 link: 13 Widget present, but link not alive! | |
WARNING: xbow_base: 0x9200000000000000 link: 13 Widget present, but link not alive! | |
IP35 PROM SGI Version 6.210 built 02:33:51 PM Aug 26, 2004 | |
*** Mixed standard and premium memory: | |
*** Treating all as standard. | |
Testing/Initializing memory ............... DONE | |
Copying PROM code to memory ............... DONE | |
Discovering local IO ...................... WARNING: xbow_base: 0x9200000000000000 link: 13 Widget present, but link not alive! | |
WARNING: xbow_base: 0x9200000000000000 link: 13 Widget present, but link not alive! | |
pcibus_sanity: WARNING ** Target IOC3 not initialized . . forcing initialization ** | |
DONE | |
Discovering NUMAlink connectivity ......... | |
Local hub NUMAlink is down. | |
*** Local network link down | |
DONE | |
Found 1 objects (1 hubs, 0 routers) in 5891 usec | |
Waiting for peers to complete discovery.... DONE | |
No other nodes present; becoming global master | |
Global master is /hw/rack/001/bay/01 | |
Intializing any CPUless nodes.............. DONE | |
Checking partitioning information ......... DONE | |
No other nodes present; becoming partition master | |
Local slave entering slave loop | |
Local slave entering slave loop | |
Local slave entering slave loop | |
Loading BASEIO prom ....................... DONE | |
BASEIO PROM Monitor SGI Version 6.210 built 02:30:38 PM Aug 26, 2004 (BE64) | |
4 CPUs on 1 nodes found. | |
Automatic update of PROM environment disabled | |
Graphics diagnostics | |
Odyssey board #0 found on nasid 0 | |
Running Odyssey xtalk sanity diag... | |
Board version 1 - Buzz revision 3B | |
On board sdram size: 128 Mb | |
Cas latency: CAS 3 | |
4 banks by sdram module | |
Running Odyssey Buzz registers diag... | |
Device passed diagnostics | |
Installing PROM Device drivers ............ | |
On-board (IO9) tigon3 1000BaseT interface | |
Base I/O Ethernet set to /dev/ethernet/tg0 | |
Installing Graphics Console... | |
graphics install: searching for pipe 0 | |
Probing IOC4 ATA adapter 2 | |
IOC4 RevId = 79 | |
Detected Vendor id/Product MATSHITA DVD-ROM SR-8588 | |
Walking SCSI Adapter 0, (pci id 3) | |
1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s) | |
Walking SCSI Adapter 1, (pci id 3) | |
1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s) | |
Initializing PROM Device drivers .......... | |
Initializing Base I/O Ethernet Interface...Failed. MII Status Register = 0x7949 | |
Done. | |
---------------Interface Configuration Summary---------------- | |
ASIC|Revision|MAC Address : 5701|B5|08:00:69:13:ea:b8 | |
Link Negotiation|Advertisement : On|<H10 F10 H100 F100 F1000> | |
Link|Speed|Duplex|Rx/Tx FlowCtrl: Down|10|Half|Off/Off | |
-------------------------------------------------------------- | |
DONE | |
Cannot connect to keyboard -- check the cable. | |
Cannot open /dev/input/ioc4pckm0 for input | |
Cannot connect to keyboard -- check the cable. | |
Cannot open /dev/input/ioc4pckm0 for input | |
Checking hardware inventory ............... | |
***Warning: Board in module 001c01 is missing or disabled | |
It previously contained a IBRICK board, barcode NCC044 laser 73858e | |
***Warning: Found a new New Type board in module 001c01, serial | |
Please use the 'update' command from the PROM Monitor to update the inventory | |
DONE | |
**** System Configuration and Diagnostics Summary **** | |
CONFIG: | |
No. of NODEs enabled = 1 | |
No. of NODEs disabled = 0 | |
No. of CPUs enabled = 4 | |
No. of CPUs disabled = 0 | |
Mem enabled = 4096 MB | |
Mem disabled = 0 MB | |
No. of RTRs enabled = 0 | |
No. of RTRs disabled = 0 | |
DIAG RESULTS: | |
/hw/module/001c01/brick/xtalk/13: IO link bad | |
**** End System Configuration and Diagnostics Summary **** | |
System Maintenance Menu | |
1) Start System | |
2) Install System Software | |
3) Run Diagnostics | |
4) Recover System | |
5) Enter Command Monitor | |
Option? 5 | |
Command Monitor. Type "exit" to return to the menu. | |
>> hinv | |
System SGI-IP35 | |
4 800 MHz IP35 Processors | |
Main memory size: 4096 Mbytes | |
Graphics Controller | |
PCI IOC4: in slot 1, (adapter 0) | |
PCI Gigabit Ethernet (tigon3) Controller 1 | |
Integral SCSI controller 2: Version IOC4 ATA | |
CDROM: unit 0 on SCSI Controller 2, (cdrom(2,0,7)) | |
Integral SCSI controller 0: Version Qlogic 12160 | |
Integral SCSI controller 1: Version Qlogic 12160 | |
>> hinv -v | |
IP35 Node Board, Module 001c01 | |
ASIC BEDROCK Rev 2, 200 MHz, (nasid 0) | |
Processor A: 800 MHz R16000 Rev 2.2 | |
Secondary Cache 4MB 400MHz Tap 0xa , (cpu 0) | |
R16010FPC Rev 2.2 | |
Processor B: 800 MHz R16000 Rev 2.2 | |
Secondary Cache 4MB 400MHz Tap 0xa , (cpu 1) | |
R16010FPC Rev 2.2 | |
Processor C: 800 MHz R16000 Rev 2.2 | |
Secondary Cache 4MB 400MHz Tap 0xa , (cpu 2) | |
R16010FPC Rev 2.2 | |
Processor D: 800 MHz R16000 Rev 2.2 | |
Secondary Cache 4MB 400MHz Tap 0xa , (cpu 3) | |
R16010FPC Rev 2.2 | |
Memory on board, 4096 MBytes (Standard) | |
Bank 0, 1024 MBytes (Premium) <-- (Software Bank 0) | |
Bank 1, 1024 MBytes (Premium) | |
Bank 2, 512 MBytes (Standard) | |
Bank 3, 512 MBytes (Standard) | |
Bank 4, 512 MBytes (Standard) | |
Bank 5, 512 MBytes (Standard) | |
New Type Bridge, Module 001c01 | |
IXBRICK Bridge, Module 001c01 | |
ASIC BRIDGE Rev 3, (widget 11) | |
adapter ID (Vendor 1077 Device 2312 class c subclass c) | |
(pci id 1 function 0) | |
adapter ID (Vendor 1077 Device 2312 class c subclass c) | |
(pci id 1 function 1) | |
IXBRICK Bridge, Module 001c01 | |
ASIC BRIDGE Rev 3, (widget 11) | |
adapter ID (Vendor 1077 Device 2312 class c subclass c) | |
(pci id 2 function 0) | |
adapter ID (Vendor 1077 Device 2312 class c subclass c) | |
(pci id 2 function 1) | |
IXBRICK Bridge, Module 001c01 | |
ASIC BRIDGE Rev 3, (widget 15) | |
adapter IOC4 Rev 4f | |
(pci id 1) | |
adapter IOC4-ATA Rev 4f | |
(pci id 1) | |
peripheral CDROM, BUS 0, ID 0, MATSHITA DVD-ROM SR-8588 | |
adapter ID (Vendor 104c Device ac28 class 6 subclass 6) | |
(pci id 2) | |
adapter PCI (SCSI interface) Rev 6 | |
(pci id 3) | |
adapter GigE Rev 15 | |
(pci id 4) | |
IXBRICK Bridge, Module 001c01 | |
ASIC BRIDGE Rev 3, (widget 15) | |
adapter RAD | |
(pci id 1) | |
adapter ID (Vendor 1077 Device 1240 class 1 subclass 1) | |
(pci id 3) | |
ASIC XBOW Rev 3, on CBrick, Module 001c01 | |
ODYSSEY Graphics Board, Module 001c01 | |
>> hinv -mv | |
Usage: hinv [-v] [-m] [-mvvv] [-g PATH]: | |
Display hardware inventory | |
>> hinv -mvvv | |
location: /hw/rack/001/bay/01 | |
Part:030-1956-002;Name:IP53_4CPU;Serial:NCG100;Revision:-B;Group:ff;Capability:ffffffff;Variety:ff;Laser:000000005423b110; | |
location: /hw/rack/001/bay/01 | |
Part:030-1881-006;Name:WS_INT_53;Serial:NAA342;Revision:-A;Group:ff;Capability:ffffffff;Variety:ff;Laser:0000000053ec3442; | |
location: /hw/rack/001/bay/01 | |
Part:030-1881-006;Name:WS_INT_53;Serial:NAA342;Revision:-A;Group:ff;Capability:ffffffff;Variety:ff;Laser:0000000053ec3442; | |
location: /hw/rack/001/bay/01 | |
Part:030-1884-002;Name:ODY128B1_2;Serial:MZF948;Revision:-D;Group:ff;Capability:ffffffff;Variety:ff;Laser:0000000052d5f6e8; | |
location: /hw/rack/001/bay/01 | |
Part:030-1881-006;Name:WS_INT_53;Serial:NAA342;Revision:-A;Group:ff;Capability:ffffffff;Variety:ff;Laser:0000000053ec3442; | |
location: /hw/rack/001/bay/01 | |
Part:030-1881-006;Name:WS_INT_53;Serial:NAA342;Revision:-A;Group:ff;Capability:ffffffff;Variety:ff;Laser:0000000053ec3442; | |
>> exit | |
System Maintenance Menu | |
1) Start System | |
2) Install System Software | |
3) Run Diagnostics | |
4) Recover System | |
5) Enter Command Monitor | |
Option? 2 | |
Installing System Software... | |
Press <Esc> to return to the menu. | |
1) Remote Directory 2)[Local CD-ROM] | |
*a) Local SCSI CD-ROM drive 0, on controller 2 | |
Enter 1-2 to select source type, a to select the source, <esc> to quit, | |
or <enter> to start: | |
Insert the installation CD-ROM, then press <enter>: | |
OpenBSD/sgi-IP27 ARCBios boot version 1.4 | |
arg 0: scsi(2)cdrom(0)partition(8)sash64 | |
arg 1: OSLoadOptions=mini | |
arg 2: ConsoleIn=/dev/tty/hubtty0 | |
arg 3: ConsoleOut=/dev/tty/hubtty0 | |
arg 4: SystemPartition=dksc(0,1,8) | |
arg 5: OSLoader=sash | |
arg 6: OSLoadPartition=dksc(0,1,0) | |
arg 7: OSLoadFilename=unix | |
Boot: scsi(2)cdrom(0)partition(0)/bsd.rd.IP27 | |
9173168+677136 [58+216624+130463]=0x9b9c50 | |
ARCS64 Firmware | |
Found SGI-IP35, setting up. | |
Machine is in M mode. |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment