Skip to content

Instantly share code, notes, and snippets.

Embed
What would you like to do?
PlayStation Classic boot log
Watchdog Status: 0 , boot from normal
mt_pll_init +
CLK_GATING_CTRL1:d891923e
after set, CLK_GATING_CTRL1:d891923e
CLK_GATING_CTRL2:7afdbf10
[PWRAP] pmic ID: 2092.
[EMI] MDL number = 0
[EMI] PCDDR3
Vcore HV NV LV, Vdram HV NV LV
0x5f 0x48 0x3f, 0xc 0x0 0x3
get dram size from AUXADC1 0 0
[EMI] Use Common DDR3 x32 emi settings
[EMI] Config emi settings:
EMI_CONA=0x2012, EMI_CONH=0x3
EMI_RANK0=0x40000000, EMI_RANK1=0x0
EMI_CONA=0x2012
EMI_CONF=0x4210000
EMI_CONH=0x3
[DramcSwImpedanceCal] FINAL: DRVP=7, DRVN=6
PCDDR3 Pinmux 0
SSC OFF
DRAM Clock: 1584MHz
[Write Leveling]
WriteLevelingMoveDQSInsteadOfCLK
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
WL Clk delay = 0, CA CLK delay = 0
No need to update CA/CS delay because the CLK delay is small than CA training.
Final Clk output delay = 0
R0 FINAL: WriteLeveling DQS:(2, 0) OEN:(1, 2) DQS0 delay = 36
R0 FINAL: WriteLeveling DQS:(2, 0) OEN:(1, 2) DQS1 delay = 35
R0 FINAL: WriteLeveling DQS:(2, 0) OEN:(1, 2) DQS2 delay = 33
R0 FINAL: WriteLeveling DQS:(2, 0) OEN:(1, 2) DQS3 delay = 33
[DramcWriteLeveling] ====Done====
[Gating]
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
[Byte 0]First pass (1, 3, 12)
[Byte 1]First pass (1, 3, 12)
[Byte 2]First pass (1, 3, 12)
[Byte 3]First pass (1, 3, 12)
[Byte 3]Bigger pass win(1, 5, 4) Pass tap=56
[Byte 0]Bigger pass win(1, 5, 5) Pass tap=57
[Byte 2]Bigger pass win(1, 5, 5) Pass tap=57
[Byte 1]Bigger pass win(1, 5, 6) Pass tap=58
===============================================================================
dqs input gating widnow, final delay value
Frequency=1600 rank=0
===============================================================================
R0 FINAL: GW best DQS0 P0 delay(2T, 0.5T, PI) = (1, 4, 8) [tap = 57]
R0 FINAL: GW best DQS1 P0 delay(2T, 0.5T, PI) = (1, 4, 9) [tap = 58]
R0 FINAL: GW best DQS2 P0 delay(2T, 0.5T, PI) = (1, 4, 8) [tap = 57]
R0 FINAL: GW best DQS3 P0 delay(2T, 0.5T, PI) = (1, 4, 8) [tap = 56]
R0 FINAL: GW best DQS0 P1 delay(2T, 0.5T, PI) = (1, 6, 8)
R0 FINAL: GW best DQS1 P1 delay(2T, 0.5T, PI) = (1, 6, 9)
R0 FINAL: GW best DQS2 P1 delay(2T, 0.5T, PI) = (1, 6, 8)
R0 FINAL: GW best DQS3 P1 delay(2T, 0.5T, PI) = (1, 6, 8)
[DramcRxdqsGatingCal] ====Done====
[DATLAT]
DATLAT Default value = 0xf
5, 0xFFFFFFFF, sum=0
6, 0xFFFFFFFF, sum=0
7, 0xFFFFFFFF, sum=0
8, 0xFFFFFFFF, sum=0
9, 0xFFFFFFFF, sum=0
10, 0xFFFFFFFF, sum=0
11, 0xFFFFFFFF, sum=0
12, 0xFFFFFFFF, sum=0
13, 0x0, sum=1
14, 0x0, sum=2
15, 0x0, sum=3
16, 0x0, sum=4
17, 0x0, sum=5
pattern=5 first_step=13 total pass=6 best_step=15
R0 FINAL: DATLAT = 15 [13 ~ 18]
[DramcRxdatlatCal] ====Done====
[RX]
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
RX Window Sum 951
R0 FINAL: RX Bit 0, 14 (-2 ~ 30) 33
R0 FINAL: RX Bit 1, 14 (-1 ~ 29) 31
R0 FINAL: RX Bit 2, 15 (-1 ~ 31) 33
R0 FINAL: RX Bit 3, 14 (-1 ~ 29) 31
R0 FINAL: RX Bit 4, 14 (2 ~ 27) 26
R0 FINAL: RX Bit 5, 14 (-1 ~ 30) 32
R0 FINAL: RX Bit 6, 14 (0 ~ 29) 30
R0 FINAL: RX Bit 7, 14 (-1 ~ 29) 31
R0 FINAL: RX Bit 8, 14 (0 ~ 29) 30
R0 FINAL: RX Bit 9, 15 (-1 ~ 31) 33
R0 FINAL: RX Bit 10, 16 (1 ~ 31) 31
R0 FINAL: RX Bit 11, 14 (0 ~ 29) 30
R0 FINAL: RX Bit 12, 15 (0 ~ 30) 31
R0 FINAL: RX Bit 13, 15 (-1 ~ 31) 33
R0 FINAL: RX Bit 14, 14 (0 ~ 29) 30
R0 FINAL: RX Bit 15, 14 (-1 ~ 29) 31
R0 FINAL: RX Bit 16, 17 (2 ~ 33) 32
R0 FINAL: RX Bit 17, 16 (0 ~ 32) 33
R0 FINAL: RX Bit 18, 16 (1 ~ 32) 32
R0 FINAL: RX Bit 19, 17 (1 ~ 33) 33
R0 FINAL: RX Bit 20, 14 (-1 ~ 30) 32
R0 FINAL: RX Bit 21, 16 (1 ~ 32) 32
R0 FINAL: RX Bit 22, 15 (0 ~ 30) 31
R0 FINAL: RX Bit 23, 16 (0 ~ 32) 33
R0 FINAL: RX Bit 24, 13 (-1 ~ 28) 30
R0 FINAL: RX Bit 25, 16 (3 ~ 30) 28
R0 FINAL: RX Bit 26, 15 (2 ~ 29) 28
R0 FINAL: RX Bit 27, 15 (2 ~ 28) 27
R0 FINAL: RX Bit 28, 15 (2 ~ 29) 28
R0 FINAL: RX Bit 29, 15 (1 ~ 30) 30
R0 FINAL: RX Bit 30, 16 (2 ~ 30) 29
R0 FINAL: RX Bit 31, 16 (2 ~ 30) 29
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
DQS Delay :
DQS0 = 0, DQS1 = 0, DQS2 = 0, DQS3 = 0
DQM Delay :
DQM0 = 14, DQM1 = 14, DQM2 = 15, DQM3 = 15
DQ Delay :
DQ0 =14, DQ1 =14, DQ2 =15, DQ3 =14
DQ4 =14, DQ5 =14, DQ6 =14, DQ7 =14
DQ8 =14, DQ9 =15, DQ10 =16, DQ11 =14
DQ12 =15, DQ13 =15, DQ14 =14, DQ15 =14
DQ16 =17, DQ17 =16, DQ18 =16, DQ19 =17
DQ20 =14, DQ21 =16, DQ22 =15, DQ23 =16
DQ24 =13, DQ25 =16, DQ26 =15, DQ27 =15
DQ28 =15, DQ29 =15, DQ30 =16, DQ31 =16
________________________________________________________________________
[DramcRxWindowPerbitCal] ====Done====
[TX]
[DramcTxWindowPerbitCal] Frequency=1600, Rank=0, calType=2
[DramcTxWindowPerbitCal] Begin, TX DQ(2, 0), DQ OEN(1, 2)
TX Window Sum 849
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
R0 FINAL: TX Bit0 (38~64) 27 51, Bit8 (39~64) 26 51, Bit16 (37~63) 27 50, Bit24 (35~61) 27 48
R0 FINAL: TX Bit1 (37~64) 28 50, Bit9 (39~65) 27 52, Bit17 (36~62) 27 49, Bit25 (38~63) 26 50
R0 FINAL: TX Bit2 (38~64) 27 51, Bit10 (39~65) 27 52, Bit18 (37~63) 27 50, Bit26 (37~62) 26 49
R0 FINAL: TX Bit3 (37~63) 27 50, Bit11 (38~64) 27 51, Bit19 (36~63) 28 49, Bit27 (37~61) 25 49
R0 FINAL: TX Bit4 (39~63) 25 51, Bit12 (38~63) 26 50, Bit20 (35~62) 28 48, Bit28 (38~62) 25 50
R0 FINAL: TX Bit5 (40~64) 25 52, Bit13 (38~64) 27 51, Bit21 (37~63) 27 50, Bit29 (36~62) 27 49
R0 FINAL: TX Bit6 (38~63) 26 50, Bit14 (38~62) 25 50, Bit22 (35~62) 28 48, Bit30 (36~63) 28 49
R0 FINAL: TX Bit7 (38~63) 26 50, Bit15 (39~62) 24 50, Bit23 (38~64) 27 51, Bit31 (38~63) 26 50
==================================================================
Byte0, PI DQ Delay 51 Delay2 51
Final DQ PI Delay(LargeUI, SmallUI, PI) =(2 ,0, 51)
OEN DQ PI Delay(LargeUI, SmallUI, PI) =(1 ,2, 51)
Byte1, PI DQ Delay 51 Delay2 50
Final DQ PI Delay(LargeUI, SmallUI, PI) =(2 ,0, 50)
OEN DQ PI Delay(LargeUI, SmallUI, PI) =(1 ,2, 50)
Byte2, PI DQ Delay 49 Delay2 50
Final DQ PI Delay(LargeUI, SmallUI, PI) =(2 ,0, 50)
OEN DQ PI Delay(LargeUI, SmallUI, PI) =(1 ,2, 50)
Byte3, PI DQ Delay 49 Delay2 49
Final DQ PI Delay(LargeUI, SmallUI, PI) =(2 ,0, 49)
OEN DQ PI Delay(LargeUI, SmallUI, PI) =(1 ,2, 49)
[DramcTxWindowPerbitCal] ====Done====
[DramcRxdqsGatingPostProcess] p->frequency 1600
[DramcRxdqsGatingPostProcess] s1ChangeDQSINCTL 0, reg_TX_dly_DQSgated_min 3, u1TXDLY_Cal_min 3
Settings after calibration ...
=== [DramcRunTimeConfig] ===
ZQCS_ENABLE: ON
LOWPOWER_GOLDEN_SETTINGS(DCM): ON
SPM_CONTROL_AFTERK: ON
TEMP_SENSOR_ENABLE: OFF
ENABLE_PER_BANK_REFRESH: OFF
HW_SAVE_FOR_SR: OFF
=========================
0:dram_rank_size:40000000
dram size 0x40000000.
[MEM] complex R/W mem test pass
CLK_MUX_REG =0x27109726
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
phase: [map:1ffffff] [maxlen:25] [final:8]
Final cmd pad delay: 8
[MSDC] DMA DAT CRC error(8000h)
[MSDC]<CHECKME> Unexpected INT(0x8000)
[MSDC] DMA DAT CRC error(8000h)
[MSDC] DMA DAT CRC error(8000h)
[MSDC] DMA DAT CRC error(8000h)
[MSDC] DMA DAT CRC error(8000h)
[MSDC] DMA DAT CRC error(8000h)
phase: [map:3ffffff] [maxlen:26] [final:8]
Final data pad delay: 8
[eMMC] Size: 14910 MB, Max.Speed: 200000 kHz, blklen(512), nblks(30535680), ro(0)
starting app fitboot
block devices:
mmc0, size 15634268160, bsize 512, ref 11, label <null> (no erase geometry)
mmc0p1, size 8388608, bsize 512, ref 2, label BOOTIMG1 (no erase geometry)
mmc0p2, size 8388608, bsize 512, ref 2, label BOOTIMG2 (no erase geometry)
mmc0p3, size 524288, bsize 512, ref 2, label SEC_RO (no erase geometry)
mmc0p4, size 524288, bsize 512, ref 2, label MISC (no erase geometry)
mmc0p5, size 2097152, bsize 512, ref 2, label TEE1 (no erase geometry)
mmc0p6, size 2097152, bsize 512, ref 2, label TEE2 (no erase geometry)
mmc0p7, size 209715200, bsize 512, ref 2, label ROOTFS1 (no erase geometry)
mmc0p8, size 41943040, bsize 512, ref 2, label ROOTFS2 (no erase geometry)
mmc0p9, size 15032385536, bsize 512, ref 2, label GAADATA (no erase geometry)
mmc0p10, size 327614464, bsize 512, ref 2, label USRDATA (no erase geometry)
mmc0boot0, size 4194304, bsize 512, ref 1, label <null> (no erase geometry)
mmc0boot1, size 4194304, bsize 512, ref 1, label <null> (no erase geometry)
mmc0rpmb, size 4194304, bsize 512, ref 2, label <null> (no erase geometry)
fastboot_init()
[USB] udc_start_cond
MT_USB0_IRQ_ID: 104
Watchdog Status: 0 , boot from normal
mt_pll_init +
CLK_GATING_CTRL1:d891923e
after set, CLK_GATING_CTRL1:d891923e
CLK_GATING_CTRL2:7afdbf10
[PWRAP] pmic ID: 2092.
[EMI] MDL number = 0
[EMI] PCDDR3
Vcore HV NV LV, Vdram HV NV LV
0x5f 0x48 0x3f, 0xc 0x0 0x3
get dram size from AUXADC1 0 0
[EMI] Use Common DDR3 x32 emi settings
[EMI] Config emi settings:
EMI_CONA=0x2012, EMI_CONH=0x3
EMI_RANK0=0x40000000, EMI_RANK1=0x0
EMI_CONA=0x2012
EMI_CONF=0x4210000
EMI_CONH=0x3
[DramcSwImpedanceCal] FINAL: DRVP=7, DRVN=6
PCDDR3 Pinmux 0
SSC OFF
DRAM Clock: 1584MHz
[Write Leveling]
WriteLevelingMoveDQSInsteadOfCLK
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
WL Clk delay = 0, CA CLK delay = 0
No need to update CA/CS delay because the CLK delay is small than CA training.
Final Clk output delay = 0
R0 FINAL: WriteLeveling DQS:(2, 0) OEN:(1, 2) DQS0 delay = 37
R0 FINAL: WriteLeveling DQS:(2, 0) OEN:(1, 2) DQS1 delay = 36
R0 FINAL: WriteLeveling DQS:(2, 0) OEN:(1, 2) DQS2 delay = 33
R0 FINAL: WriteLeveling DQS:(2, 0) OEN:(1, 2) DQS3 delay = 33
[DramcWriteLeveling] ====Done====
[Gating]
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
[Byte 0]First pass (1, 3, 12)
[Byte 1]First pass (1, 3, 12)
[Byte 2]First pass (1, 3, 12)
[Byte 3]First pass (1, 3, 12)
[Byte 0]Bigger pass win(1, 5, 5) Pass tap=57
[Byte 3]Bigger pass win(1, 5, 5) Pass tap=57
[Byte 2]Bigger pass win(1, 5, 6) Pass tap=58
[Byte 1]Bigger pass win(1, 5, 7) Pass tap=59
===============================================================================
dqs input gating widnow, final delay value
Frequency=1600 rank=0
===============================================================================
R0 FINAL: GW best DQS0 P0 delay(2T, 0.5T, PI) = (1, 4, 8) [tap = 57]
R0 FINAL: GW best DQS1 P0 delay(2T, 0.5T, PI) = (1, 4, 9) [tap = 59]
R0 FINAL: GW best DQS2 P0 delay(2T, 0.5T, PI) = (1, 4, 9) [tap = 58]
R0 FINAL: GW best DQS3 P0 delay(2T, 0.5T, PI) = (1, 4, 8) [tap = 57]
R0 FINAL: GW best DQS0 P1 delay(2T, 0.5T, PI) = (1, 6, 8)
R0 FINAL: GW best DQS1 P1 delay(2T, 0.5T, PI) = (1, 6, 9)
R0 FINAL: GW best DQS2 P1 delay(2T, 0.5T, PI) = (1, 6, 9)
R0 FINAL: GW best DQS3 P1 delay(2T, 0.5T, PI) = (1, 6, 8)
[DramcRxdqsGatingCal] ====Done====
[DATLAT]
DATLAT Default value = 0xf
5, 0xFFFFFFFF, sum=0
6, 0xFFFFFFFF, sum=0
7, 0xFFFFFFFF, sum=0
8, 0xFFFFFFFF, sum=0
9, 0xFFFFFFFF, sum=0
10, 0xFFFFFFFF, sum=0
11, 0xFFFFFFFF, sum=0
12, 0xFFFFFFFF, sum=0
13, 0x200000, sum=0
14, 0x0, sum=1
15, 0x0, sum=2
16, 0x0, sum=3
17, 0x0, sum=4
18, 0x0, sum=5
pattern=5 first_step=14 total pass=6 best_step=16
R0 FINAL: DATLAT = 16 [14 ~ 19]
[DramcRxdatlatCal] ====Done====
[RX]
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
RX Window Sum 944
R0 FINAL: RX Bit 0, 14 (-2 ~ 30) 33
R0 FINAL: RX Bit 1, 13 (-2 ~ 29) 32
R0 FINAL: RX Bit 2, 15 (-1 ~ 31) 33
R0 FINAL: RX Bit 3, 13 (-2 ~ 29) 32
R0 FINAL: RX Bit 4, 14 (2 ~ 27) 26
R0 FINAL: RX Bit 5, 14 (-1 ~ 30) 32
R0 FINAL: RX Bit 6, 15 (1 ~ 29) 29
R0 FINAL: RX Bit 7, 13 (-2 ~ 29) 32
R0 FINAL: RX Bit 8, 15 (0 ~ 30) 31
R0 FINAL: RX Bit 9, 15 (-1 ~ 31) 33
R0 FINAL: RX Bit 10, 16 (1 ~ 31) 31
R0 FINAL: RX Bit 11, 14 (0 ~ 29) 30
R0 FINAL: RX Bit 12, 15 (0 ~ 30) 31
R0 FINAL: RX Bit 13, 15 (-1 ~ 31) 33
R0 FINAL: RX Bit 14, 14 (0 ~ 29) 30
R0 FINAL: RX Bit 15, 14 (-1 ~ 29) 31
R0 FINAL: RX Bit 16, 17 (2 ~ 33) 32
R0 FINAL: RX Bit 17, 16 (1 ~ 32) 32
R0 FINAL: RX Bit 18, 16 (1 ~ 32) 32
R0 FINAL: RX Bit 19, 17 (1 ~ 33) 33
R0 FINAL: RX Bit 20, 15 (0 ~ 30) 31
R0 FINAL: RX Bit 21, 17 (2 ~ 32) 31
R0 FINAL: RX Bit 22, 15 (1 ~ 30) 30
R0 FINAL: RX Bit 23, 16 (1 ~ 32) 32
R0 FINAL: RX Bit 24, 14 (1 ~ 28) 28
R0 FINAL: RX Bit 25, 17 (4 ~ 30) 27
R0 FINAL: RX Bit 26, 15 (2 ~ 29) 28
R0 FINAL: RX Bit 27, 15 (3 ~ 28) 26
R0 FINAL: RX Bit 28, 15 (2 ~ 29) 28
R0 FINAL: RX Bit 29, 16 (2 ~ 30) 29
R0 FINAL: RX Bit 30, 16 (2 ~ 30) 29
R0 FINAL: RX Bit 31, 16 (2 ~ 30) 29
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
DQS Delay :
DQS0 = 0, DQS1 = 0, DQS2 = 0, DQS3 = 0
DQM Delay :
DQM0 = 13, DQM1 = 14, DQM2 = 16, DQM3 = 15
DQ Delay :
DQ0 =14, DQ1 =13, DQ2 =15, DQ3 =13
DQ4 =14, DQ5 =14, DQ6 =15, DQ7 =13
DQ8 =15, DQ9 =15, DQ10 =16, DQ11 =14
DQ12 =15, DQ13 =15, DQ14 =14, DQ15 =14
DQ16 =17, DQ17 =16, DQ18 =16, DQ19 =17
DQ20 =15, DQ21 =17, DQ22 =15, DQ23 =16
DQ24 =14, DQ25 =17, DQ26 =15, DQ27 =15
DQ28 =15, DQ29 =16, DQ30 =16, DQ31 =16
________________________________________________________________________
[DramcRxWindowPerbitCal] ====Done====
[TX]
[DramcTxWindowPerbitCal] Frequency=1600, Rank=0, calType=2
[DramcTxWindowPerbitCal] Begin, TX DQ(2, 0), DQ OEN(1, 2)
TX Window Sum 856
===============================================================================
Dram Type= 4, Freqency= 1600, rank 0
odt_onoff= 0, Byte mode= 0, Read_DBI= 0, Write DBI= 0
===============================================================================
R0 FINAL: TX Bit0 (38~65) 28 51, Bit8 (40~65) 26 52, Bit16 (37~63) 27 50, Bit24 (35~61) 27 48
R0 FINAL: TX Bit1 (38~65) 28 51, Bit9 (41~67) 27 54, Bit17 (36~62) 27 49, Bit25 (38~63) 26 50
R0 FINAL: TX Bit2 (39~67) 29 53, Bit10 (41~68) 28 54, Bit18 (37~63) 27 50, Bit26 (37~62) 26 49
R0 FINAL: TX Bit3 (38~65) 28 51, Bit11 (40~65) 26 52, Bit19 (36~63) 28 49, Bit27 (37~61) 25 49
R0 FINAL: TX Bit4 (40~65) 26 52, Bit12 (40~65) 26 52, Bit20 (35~61) 27 48, Bit28 (38~62) 25 50
R0 FINAL: TX Bit5 (41~65) 25 53, Bit13 (40~65) 26 52, Bit21 (37~63) 27 50, Bit29 (36~62) 27 49
R0 FINAL: TX Bit6 (39~65) 27 52, Bit14 (39~65) 27 52, Bit22 (35~62) 28 48, Bit30 (36~62) 27 49
R0 FINAL: TX Bit7 (39~65) 27 52, Bit15 (41~65) 25 53, Bit23 (38~64) 27 51, Bit31 (38~63) 26 50
==================================================================
Byte0, PI DQ Delay 52 Delay2 53
Final DQ PI Delay(LargeUI, SmallUI, PI) =(2 ,0, 53)
OEN DQ PI Delay(LargeUI, SmallUI, PI) =(1 ,2, 53)
Byte1, PI DQ Delay 53 Delay2 53
Final DQ PI Delay(LargeUI, SmallUI, PI) =(2 ,0, 53)
OEN DQ PI Delay(LargeUI, SmallUI, PI) =(1 ,2, 53)
Byte2, PI DQ Delay 49 Delay2 49
Final DQ PI Delay(LargeUI, SmallUI, PI) =(2 ,0, 49)
OEN DQ PI Delay(LargeUI, SmallUI, PI) =(1 ,2, 49)
Byte3, PI DQ Delay 49 Delay2 49
Final DQ PI Delay(LargeUI, SmallUI, PI) =(2 ,0, 49)
OEN DQ PI Delay(LargeUI, SmallUI, PI) =(1 ,2, 49)
[DramcTxWindowPerbitCal] ====Done====
[DramcRxdqsGatingPostProcess] p->frequency 1600
[DramcRxdqsGatingPostProcess] s1ChangeDQSINCTL 0, reg_TX_dly_DQSgated_min 3, u1TXDLY_Cal_min 3
Settings after calibration ...
=== [DramcRunTimeConfig] ===
ZQCS_ENABLE: ON
LOWPOWER_GOLDEN_SETTINGS(DCM): ON
SPM_CONTROL_AFTERK: ON
TEMP_SENSOR_ENABLE: OFF
ENABLE_PER_BANK_REFRESH: OFF
HW_SAVE_FOR_SR: OFF
=========================
0:dram_rank_size:40000000
dram size 0x40000000.
[MEM] complex R/W mem test pass
CLK_MUX_REG =0x27109726
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
[MSDC] cmd21 CRCERR! (0x400)
phase: [map:1ffffff] [maxlen:25] [final:8]
Final cmd pad delay: 8
[MSDC] DMA DAT CRC error(8000h)
[MSDC]<CHECKME> Unexpected INT(0x8000)
[MSDC] DMA DAT CRC error(8000h)
[MSDC] DMA DAT CRC error(8000h)
[MSDC] DMA DAT CRC error(8000h)
[MSDC] DMA DAT CRC error(8000h)
[MSDC] DMA DAT CRC error(8000h)
phase: [map:3ffffff] [maxlen:26] [final:8]
Final data pad delay: 8
[eMMC] Size: 14910 MB, Max.Speed: 200000 kHz, blklen(512), nblks(30535680), ro(0)
starting app fitboot
open MISC successfully
lastboot = 0, use A = 0, use B = 0, current = 0
***last succeed boot from A system,upgrade B failed or no upgrade B***
***now boot from system A***
choose first boot partition:BOOTIMG1 , tee choose: TEE1
0:dram_rank_size:40000000
dram size 0x40000000.
0:dram_rank_size:40000000
dram size 0x40000000.
0:dram_rank_size:40000000
dram size 0x40000000.
0:dram_rank_size:40000000
dram size 0x40000000.
Partition [DTBO] is not exist.
LK run time: 1170085 (us)
jump to tz 0x42ff6000
[teeloader] tl jump to atf!
[ATF](0)[1.170976]INFO: Kernel is AArch32
[ATF](0)[1.172283]NOTICE: BL3-1: v1.2(debug):99621ed
[ATF](0)[1.172857]NOTICE: BL3-1: Built : 16:37:18, Sep 1 2018
[ATF](0)[1.173557]NOTICE: BL31: v1.2(debug):99621ed
[ATF](0)[1.174138]NOTICE: BL31: Built : 16:37:18, Sep 1 2018
[ATF](0)[1.174829]INFO: [spmc_init]change to SPMC mode !!!
[ATF](0)[1.175511]INFO: ARM GICv2 driver initialized
[ATF](0)[1.176123]INFO: BL31: Initializing runtime services
[ATF](0)[1.176822]INFO: BL31: Initializing BL32
EMI_MPUS = 20000160, EMI_MPUT = 400fffb0
[DAPC] [TEE] dapc_register_ext_handler is called by Type_2B slave(5)
[ATF](0)[1.178806]INFO: BL31: Preparing for EL3 exit to normal world
[ATF](0)[1.179574]INFO: Entry point address = 0x41e00000
[ATF](0)[1.180231]INFO: SPSR = 0x1d3
[ 0.000000] <0>-(0)[0:swapper]Booting Linux on physical CPU 0x0
[ 0.000000] <0>-(0)[0:swapper]Initializing cgroup subsys cpu
[ 0.000000] <0>-(0)[0:swapper]Initializing cgroup subsys cpuacct
[ 0.000000] <0>-(0)[0:swapper]Linux version 4.4.22 (mtk@b02b676401a1) (gcc version 6.2.0 (GCC) ) #1 SMP PREEMPT Sun Sep 9 15:21:14 UTC 2018
[ 0.000000] <0>-(0)[0:swapper]CPU: ARMv7 Processor [410fd041] revision 1 (ARMv7), cr=10c0383d
[ 0.000000] <0>-(0)[0:swapper]CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] <0>-(0)[0:swapper]Machine model: MT8167
[ 0.000000] <0>-(0)[0:swapper]earlycon: Early serial console at MMIO32 0x11005000 (options '')
[ 0.000000] <0>-(0)[0:swapper]bootconsole [uart0] enabled
[ 0.000000] <0>-(0)[0:swapper][PHY layout]atf-reserved-memory@43000000 : 0x43000000 - 0x4302ffff (0x30000)
[ 0.000000] <0>-(0)[0:swapper][PHY layout]mtee-reserved-memory : 0x7fd00000 - 0x7fffffff (0x300000)
[ 0.000000] <0>-(0)[0:swapper]Memory policy: Data cache writealloc
[ 0.000000] <0>-(0)[0:swapper][PHY layout]kernel : 0x40000000 - 0x42ffffff (0x03000000)
[ 0.000000] <0>-(0)[0:swapper][PHY layout]kernel : 0x43030000 - 0x7fcfffff (0x3ccd0000)
[ 0.000000] <0>-(0)[0:swapper]psci: probing for conduit method from DT.
[ 0.000000] <0>-(0)[0:swapper]psci: PSCIv1.0 detected in firmware.
[ 0.000000] <0>-(0)[0:swapper]psci: Using standard PSCI v0.2 function IDs
[ 0.000000] <0>-(0)[0:swapper]psci: Trusted OS migration not required
[ 0.000000] <0>-(0)[0:swapper]PERCPU: Embedded 13 pages/cpu @dffa5000 s21580 r8192 d23476 u53248
[ 0.000000] <0>-(0)[0:swapper]Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260288
[ 0.000000] <0>-(0)[0:swapper][cpu_ntf] <00>c00b668c (page_alloc_cpu_notify)
[ 0.000000] <0>-(0)[0:swapper]Kernel command line: console=tty0 console=ttyS0,921600n1 earlycon=uart8250,mmio32,0x11005000 root=/dev/mmcblk0p7 fsck.repair=yes rootwait vmalloc=496M androidboot.hardware=aud8516p1_linux
[ 0.000000] <0>-(0)[0:swapper]PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] <0>-(0)[0:swapper]Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] <0>-(0)[0:swapper]Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] <0>-(0)[0:swapper]Memory: 1024564K/1045312K available (7407K kernel code, 441K rwdata, 2876K rodata, 308K init, 579K bss, 20748K reserved, 0K cma-reserved, 513024K highmem)
[ 0.000000] <0>-(0)[0:swapper]Virtual kernel memory layout:
[ 0.000000] <0> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] <0> fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] <0> vmalloc : 0xe1000000 - 0xff800000 ( 488 MB)
[ 0.000000] <0> lowmem : 0xc0000000 - 0xe0800000 ( 520 MB)
[ 0.000000] <0> pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] <0> modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] <0> .text : 0xc0008000 - 0xc0a13000 (10284 kB)
[ 0.000000] <0> .init : 0xc0a13000 - 0xc0a60000 ( 308 kB)
[ 0.000000] <0> .data : 0xc0a60000 - 0xc0ace7f0 ( 442 kB)
[ 0.000000] <0> .bss : 0xc0ad0000 - 0xc0b60e64 ( 580 kB)
[ 0.000000] <0>-(0)[0:swapper][cpu_ntf] <00>c00e3f04 (slab_cpuup_callback)
[ 0.000000] <0>-(0)[0:swapper]SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] <0>-(0)[0:swapper/0][cpu_ntf] <00>c004f030 (sched_ilb_notifier)
[ 0.000000] <0>-(0)[0:swapper/0]Preemptible hierarchical RCU implementation.
[ 0.000000] <0>-(0)[0:swapper/0] Build-time adjustment of leaf fanout to 32.
[ 0.000000] <0>-(0)[0:swapper/0][cpu_ntf] <00>c0078300 (rcu_cpu_notify)
[ 0.000000] <0>-(0)[0:swapper/0][cpu_ntf] <00>c020449c (radix_tree_callback)
[ 0.000000] <0>-(0)[0:swapper/0]NR_IRQS:16 nr_irqs:16 16
[ 0.000000] <0>-(0)[0:swapper/0][cpu_ntf] <00>c02233c4 (gic_secondary_init)
[ 0.000000] <0>-(0)[0:swapper/0][cpu_ntf] <00>c007b99c (timer_cpu_notify)
[ 0.000000] <0>-(0)[0:swapper/0][cpu_ntf] <00>c007d778 (hrtimer_cpu_notify)
[ 0.000000] <0>-(0)[0:swapper/0][cpu_ntf] <00>c050d6b0 (arch_timer_cpu_notify)
[ 0.000000] <0>-(0)[0:swapper/0]Architected cp15 timer(s) running at 13.00MHz (virt).
[ 0.000000] <0>-(0)[0:swapper/0]clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[ 0.000006] <0>-(0)[0:swapper/0]sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.001282] <0>-(0)[0:swapper/0]Switching to timer-based delay loop, resolution 76ns
[ 0.002384] <0>-(0)[0:swapper/0]clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 147020034397 ns
[ 0.004097] <0>-(0)[0:swapper/0][cpu_ntf] <00>c008eb7c (hotplug_cfd)
[ 0.004995] <0>.(0)[0:swapper/0]Console: colour dummy device 80x30
[ 0.007158] <0>.(0)[0:swapper/0]console [tty0] enabled
[ 0.007888] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[ 0.009280] <0>.(0)[0:swapper/0]pid_max: default: 32768 minimum: 301
[ 0.010180] <0>.(0)[0:swapper/0][cpu_ntf] <00>c0114d90 (buffer_cpu_notify)
[ 0.011101] <0>.(0)[0:swapper/0]Security Framework initialized
[ 0.011909] <0>.(0)[0:swapper/0]Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.013035] <0>.(0)[0:swapper/0]Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.014378] <0>.(0)[0:swapper/0][cpu_ntf] <00>c00badd8 (ratelimit_handler)
[ 0.015545] CPU: Testing write buffer coherency: ok
[ 0.016227] <0>.(0)[0:swapper/0][cpu_ntf] <00>c0027ecc (smpboot_thread_call)
[ 0.017264] <0>-(0)[0:swapper/0]init_heavy_tlb start.
[ 0.017953] <0>-(0)[0:swapper/0]init_heavy_tlb: cpu=0 thresh_l=2147483647 thresh_h=358 max_capaicy=1024
[ 0.019215] <0>-(0)[0:swapper/0]init_heavy_tlb: cpu=1 thresh_l=2147483647 thresh_h=358 max_capaicy=1024
[ 0.020475] <0>-(0)[0:swapper/0]init_heavy_tlb: cpu=2 thresh_l=2147483647 thresh_h=358 max_capaicy=1024
[ 0.021736] <0>-(0)[0:swapper/0]init_heavy_tlb: cpu=3 thresh_l=2147483647 thresh_h=358 max_capaicy=1024
[ 0.023082] <0>.(0)[1:swapper/0]CPU0: update cpu_capacity 1024
[ 0.023869] <0>.(0)[1:swapper/0]CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.024894] <0>.(0)[1:swapper/0]Setting up static identity map for 0x40008280 - 0x400082d8
[ 0.026019] <0>.(0)[1:swapper/0][cpu_ntf] <00>c002c118 (cpu_callback)
[ 0.033054] <0>.(0)[1:swapper/0][cpu_ntf] <00>c003dc58 (workqueue_cpu_up_callback)
[ 0.034079] <0>.(0)[1:swapper/0][cpu_ntf] <00>c003df28 (workqueue_cpu_down_callback)
[ 0.063117] <0>.(0)[1:swapper/0][cpu_ntf] <00>c00482e8 (migration_call)
[ 0.064009] <0>.(0)[1:swapper/0][cpu_ntf] <00>c0045aec (sched_cpu_active)
[ 0.064921] <0>.(0)[1:swapper/0][cpu_ntf] <00>c0045abc (sched_cpu_inactive)
[ 0.076608] <0>.(0)[1:swapper/0]BOOTPROF: 76.600230: ON
[ 0.078385] <0>.(0)[1:swapper/0]init_get_max_DRAM_size done. phone_dram_sz: 0x0, kernel_mem_sz: 0x40000000
[ 0.080087] <0>.(0)[1:swapper/0][BOOT_REASON] 'boot_reason=' is not found
[ 0.081401] <0>.(0)[1:swapper/0]'atag,devinfo' is not found
[ 0.103403] <0>-(1)[0:swapper/1]CPU1: update cpu_capacity 1024
[ 0.103411] <0>-(1)[0:swapper/1]CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.104086] <0>-(2)[0:swapper/2]CPU2: update cpu_capacity 1024
[ 0.104094] <0>-(2)[0:swapper/2]CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.104729] <0>-(3)[0:swapper/3]CPU3: update cpu_capacity 1024
[ 0.104737] <0>-(3)[0:swapper/3]CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.104836] <0>.(0)[1:swapper/0]Brought up 4 CPUs
[ 0.110794] <0>.(0)[1:swapper/0]SMP: Total of 4 processors activated (104.00 BogoMIPS).
[ 0.111871] <0>.(0)[1:swapper/0]CPU: All CPU(s) started in SVC mode.
[ 0.112889] <0>.(0)[1:swapper/0][cpu_ntf] <00>c00451cc (sched_domains_numa_masks_update)
[ 0.114008] <0>.(0)[1:swapper/0][cpu_ntf] <00>c004ce04 (cpuset_cpu_active)
[ 0.114931] <0>.(0)[1:swapper/0][cpu_ntf] <00>c004ce5c (cpuset_cpu_inactive)
[ 0.115876] <0>.(0)[1:swapper/0][cpu_ntf] <00>c0046a9c (hotplug_hrtick)
[ 0.117212] <0>.(0)[1:swapper/0]devtmpfs: initialized
[ 0.118085] <0>.(0)[1:swapper/0][cpu_ntf] <00>c02b82e4 (device_hotplug_notifier)
[ 0.127847] VFP support v0.3:
[ 0.128242] <0>.(0)[1:swapper/0][cpu_ntf] <00>c000a51c (vfp_hotplug)
[ 0.129133] <0>.(0)[1:swapper/0]implementor 41 architecture 3 part 40 variant 4 rev 1
[ 0.130497] <0>.(0)[1:swapper/0]clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.132275] <0>.(0)[1:swapper/0]pinctrl core: initialized pinctrl subsystem
[ 0.134062] <0>.(0)[1:swapper/0][BOOT_COMMON] 'atag,boot' is not found
[ 0.135120] <0>.(0)[1:swapper/0]zone_movable_cma: uninited cma, start zone_movable_cma fail!
[ 0.136591] <0>.(0)[1:swapper/0]NET: Registered protocol family 16
[ 0.137770] <0>.(0)[1:swapper/0]DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.139420] <0>.(0)[1:swapper/0][SPM] spm_base = e106a000
[ 0.140150] <0>.(0)[1:swapper/0][SPM] spm_irq_0 = 21, spm_irq_1 = 22, spm_irq_2 = 23, spm_irq_3 = 24
[ 0.141746] <0>.(0)[1:swapper/0][MTK_CPUIDLE] error: cannot find node [mediatek,mt8167-consys]
[ 0.142905] <0>.(0)[1:swapper/0][MTK_CPUIDLE] error: cannot property_read [mediatek,mt8167-consys]
[ 0.174168] <1>.(1)[1:swapper/0]cpuidle: using governor mtk_governor
[ 0.175030] <1>.(1)[1:swapper/0]BOOTPROF: 175.024615:initcall: init_mtk_governor 30.683538ms
[ 0.178634] <1>-(1)[1:swapper/0]genirq: Setting trigger mode 2 for irq 31 failed (mtk_sysirq_set_type+0x0/0x9c)
[ 0.185539] <1>.(1)[1:swapper/0]irq: no irq domain found for /soc/pwrap@1000f000/mt6392 !
[ 0.187904] <1>.(1)[1:swapper/0]iommu: Adding device 14001000.rdma to group 0
[ 0.189269] <1>.(1)[1:swapper/0]iommu: Adding device d5af20.wdma to group 1
[ 0.190360] <1>.(1)[1:swapper/0]iommu: Adding device d5b308.wrot to group 2
[ 0.191689] <1>.(1)[1:swapper/0]iommu: Adding device 14007000.disp_ovl0 to group 3
[ 0.192904] <1>.(1)[1:swapper/0]iommu: Adding device 14009000.disp_rdma0 to group 4
[ 0.194145] <1>.(1)[1:swapper/0]iommu: Adding device 1400a000.disp_rdma1 to group 5
[ 0.195383] <1>.(1)[1:swapper/0]iommu: Adding device 1400b000.disp_wdma0 to group 6
[ 0.199104] <1>.(1)[1:swapper/0]iommu: Adding device 15009000.codec to group 7
[ 0.200611] <1>.(1)[1:swapper/0]iommu: Adding device 16000000.codec to group 8
[ 0.201770] <1>.(1)[1:swapper/0]iommu: Adding device 16000000.vcu to group 9
[ 0.202863] <1>.(1)[1:swapper/0]iommu: Adding device soc:vcu@1 to group 10
[ 0.203937] <1>.(1)[1:swapper/0]iommu: Adding device soc:vcu@2 to group 11
[ 0.205020] <1>.(1)[1:swapper/0]iommu: Adding device soc:vidcap@0 to group 12
[ 0.208088] <1>.(1)[1:swapper/0]irq: no irq domain found for /soc/pwrap@1000f000/mt6392 !
[ 0.210279] <1>.(1)[1:swapper/0]iommu: Adding device soc:pseudo-m4u to group 13
[ 0.211565] <1>.(1)[1:swapper/0]iommu: Adding device soc:pseudo-m4u-larb0 to group 14
[ 0.213066] <1>.(1)[1:swapper/0]iommu: Adding device soc:pseudo-m4u-larb1 to group 15
[ 0.214371] <1>.(1)[1:swapper/0]iommu: Adding device soc:pseudo-m4u-larb2 to group 16
[ 0.216239] <1>.(1)[1:swapper/0]BOOTPROF: 216.233692:initcall: customize_machine 39.716538ms
[ 0.217499] <1>.(1)[1:swapper/0]hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.218806] <1>.(1)[1:swapper/0]hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.221035] <1>.(1)[1:swapper/0]mtk_pctrl_init------ ok
[ 0.222025] <1>.(1)[1:swapper/0][SPM] PWAKE_EN:1, PCMWDT_EN:0, BYPASS_SYSPWREQ:0, I2C_CHANNEL:2
[ 0.223196] <1>.(1)[1:swapper/0][SLP] SLEEP_DPIDLE_EN:1, REPLACE_DEF_WAKESRC:0, SUSPEND_LOG_EN:1
[ 0.224571] <1>.(1)[1:swapper/0]### CIRQ init done. ###
[ 0.225836] <1>.(1)[1:swapper/0][DAPC] [TEE] dapc_register_ext_handler is called by Type_2B slave(0)
[ 0.227327] <1>.(1)[1:swapper/0][TZ_M4U]sec_pt_va=0x0x10a74000, pa=0x7fe74000, align=0x4000
[ 0.228458] <1>.(1)[1:swapper/0][TZ_M4U]check port security larb_base: 0xf4016000 0x0
[ 0.229518] <1>.(1)[1:swapper/0][TZ_M4U]check port security larb_base: 0xf5001000 0x0
[ 0.230578] <1>.(1)[1:swapper/0][TZ_M4U]check port security larb_base: 0xf6010000 0x0
[ 0.231648] <1>.(1)[1:swapper/0][TZ_M4U]init done.(secva0x10a26020-0x10a26020 pa0x7fe26020 sz2M)
[ 0.232834] <1>.(1)[1:swapper/0][DAPC] [TEE] dapc_register_ext_handler is called by Type_2B slave(3)
[ 0.234064] <1>.(1)[1:swapper/0][DAPC] [TEE] dapc_register_ext_handler is called by Type_2B slave(2)
[ 0.235294] <1>.(1)[1:swapper/0][DAPC] [TEE] dapc_register_ext_handler is called by Type_2B slave(6)
[ 0.248241] <1>.(1)[1:swapper/0][cpu_ntf] <00>c01ec344 (blk_cpu_notify)
[ 0.249141] <1>.(1)[1:swapper/0][cpu_ntf] <00>c01ec9c0 (blk_iopoll_cpu_notify)
[ 0.250126] <1>.(1)[1:swapper/0][cpu_ntf] <00>c01f19bc (blk_mq_main_cpu_notify)
[ 0.251116] <1>.(1)[1:swapper/0][cpu_ntf] <00>c01ef4f4 (blk_mq_queue_reinit_notify)
[ 0.252633] <0>.(0)[1:swapper/0]mtk-8250-dma: Missing dma-requests property, using 127.
[ 0.256477] <0>.(0)[1:swapper/0]SCSI subsystem initialized
[ 0.257332] <0>.(0)[1:swapper/0]usbcore: registered new interface driver usbfs
[ 0.258354] <0>.(0)[1:swapper/0]usbcore: registered new interface driver hub
[ 0.259382] <0>.(0)[1:swapper/0]usbcore: registered new device driver usb
[ 0.260567] <0>.(0)[1:swapper/0]Linux cec interface: v0.10
[ 0.261344] <0>.(0)[1:swapper/0]Linux video capture interface: v2.00
[ 0.262615] <0>.(0)[1:swapper/0]mtk_smi_common_probe 14017000.smi
[ 0.263723] <0>.(0)[1:swapper/0]mtk_smi_larb_probe 14016000.larb
[ 0.264662] <0>.(0)[1:swapper/0]mtk_smi_larb_probe 15001000.larb
[ 0.265593] <0>.(0)[1:swapper/0]mtk_smi_larb_probe 16010000.larb
[ 0.266417] <0>.(0)[1:swapper/0]mtk-iommu 10203000.m4u: bound 14016000.larb (ops mtk_smi_larb_component_ops)
[ 0.267740] <0>.(0)[1:swapper/0]mtk-iommu 10203000.m4u: bound 15001000.larb (ops mtk_smi_larb_component_ops)
[ 0.269063] <0>.(0)[1:swapper/0]mtk-iommu 10203000.m4u: bound 16010000.larb (ops mtk_smi_larb_component_ops)
[ 0.271138] <0>.(0)[1:swapper/0]Advanced Linux Sound Architecture Driver Initialized.
[ 0.272673] <0>.(0)[1:swapper/0][cpu_ntf] <00>c05b2ed8 (dev_cpu_callback)
[ 0.274387] <0>.(0)[1:swapper/0]clocksource: Switched to clocksource arch_sys_counter
[ 0.284614] <0>.(0)[1:swapper/0][ION]ion_init()
[ 0.285489] <0>.(0)[1:swapper/0][ION]ion_drv_probe() heap_nr=6
[ 0.286418] <0>.(0)[1:swapper/0]ion_heap_create: Heap type is disabled: 1
[ 0.287331] <0>.(0)[1:swapper/0]ion_mtk_heap_create: error creating heap ion_system_contig_heap type 1 base 0 size 0
[ 0.288913] <0>.(0)[1:swapper/0][ION]ion_sec_heap_create enter ion_sec_heap_create
[ 0.290153] <0>.(0)[1:swapper/0]NET: Registered protocol family 2
[ 0.291434] <0>.(0)[1:swapper/0]TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.292650] <0>.(0)[1:swapper/0]TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.293793] <0>.(0)[1:swapper/0]TCP: Hash tables configured (established 4096 bind 4096)
[ 0.294943] <0>.(0)[1:swapper/0]UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.295977] <0>.(0)[1:swapper/0]UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.297181] <0>.(0)[1:swapper/0]NET: Registered protocol family 1
[ 0.301047] <0>.(0)[1:swapper/0]futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.302179] <0>.(0)[1:swapper/0]audit: initializing netlink subsys (disabled)
[ 0.303165] <0>.(0)[1:swapper/0]audit: type=2000 audit(0.280:1): initialized
[ 0.304400] <0>.(0)[1:swapper/0][cpu_ntf] <00>c00be2f8 (cpu_callback)
[ 0.310364] <0>.(0)[1:swapper/0]VFS: Disk quotas dquot_6.6.0
[ 0.311250] <0>.(0)[1:swapper/0]VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.313502] <0>.(0)[1:swapper/0]Registering sdcardfs 0.1
[ 0.314820] <0>.(0)[1:swapper/0]fuse init (API version 7.23)
[ 0.319302] <0>.(0)[1:swapper/0]io scheduler noop registered
[ 0.320073] <0>.(0)[1:swapper/0]io scheduler deadline registered
[ 0.320906] <0>.(0)[1:swapper/0]io scheduler cfq registered (default)
[ 0.321806] <0>.(0)[1:swapper/0][cpu_ntf] <00>c021e6b4 (percpu_counter_hotcpu_callback)
[ 0.329140] <0>.(0)[1:swapper/0]Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.330782] <0>-(0)[1:swapper/0]mt-pmic-pwrap 1000f000.pwrap: unexpected interrupt int=0x1
[ 0.332369] <0>.(0)[1:swapper/0]mt6577-uart 11005000.serial: gpio20 request failed
[ 0.433621] <0>.(0)[1:swapper/0]console [ttyS0] disabled
[ 0.454503] <0>.(0)[1:swapper/0]11005000.serial: ttyS0 at MMIO 0x11005000 (irq = 50, base_baud = 1625000) is a ST16650V2
[ 0.456215] <0>.(0)[1:swapper/0]BOOTPROF: 456.209000:probe: probe=platform_drv_probe drv=mt6577-uart(c0a85b18) 123.862308ms
[ 0.457987] <0>.(0)[1:swapper/0]BOOTPROF: 457.982231:initcall: mtk8250_platform_driver_init 125.784231ms
[ 0.459801] <0>.(0)[1:swapper/0]mtk_rng 1020c000.rng: registered RNG driver
[ 0.460883] <3>.(3)[82:hwrng]random: nonblocking pool is initialized
[ 0.460950] <3>.(0)[1:swapper/0][drm] Initialized drm 1.1.0 20060810
[ 0.460962] <3>.(0)[1:swapper/0]register driver: 0 mediatek-ddp
[ 0.461212] <3>.(0)[1:swapper/0]mediatek-ddp 14015000.mm_mutex: Failed to get clock
[ 0.461414] <3>.(0)[1:swapper/0]register driver: 1 mediatek-disp-ovl
[ 0.461956] <3>.(0)[1:swapper/0]register driver: 2 mediatek-disp-rdma
[ 0.462610] <3>.(0)[1:swapper/0]register driver: 3 mediatek-dpi
[ 0.462896] <3>.(0)[1:swapper/0]mediatek-dpi 14019000.disp_dpi1: mtk_dpi_probe
[ 0.463053] <3>.(0)[1:swapper/0]mediatek-dpi 14019000.disp_dpi1: Waiting for bridge or panel driver
[ 0.463282] <3>.(0)[1:swapper/0]register driver: 4 mediatek-drm
[ 0.463482] <3>.(0)[1:swapper/0]mediatek-drm 14000000.mmsys: Waiting for cmdq device /soc/mmsys@14000000
[ 0.463681] <3>.(0)[1:swapper/0]register driver: 5 mtk-dsi
[ 0.464024] <3>.(0)[1:swapper/0]register driver: 6 mediatek-mipi-tx
[ 0.464366] <3>.(0)[1:swapper/0]register driver: 7 mediatek-drm-lvds
[ 0.464583] <3>.(0)[1:swapper/0]register driver: 8 mediatek-mt8173-lvds-tx
[ 0.465040] <3>.(0)[1:swapper/0]mediatek-hdmi-phy 10018300.hdmi-phy: Using default TX DRV impedance: 4.2k/36
[ 0.466243] <3>.(0)[1:swapper/0]mediatek-drm-hdmi 1401b000.hdmi: mtk_drm_hdmi_probe
[ 0.466358] <3>.(0)[1:swapper/0][drm] hdmi-audio-codec driver bound to HDMI
[ 0.466624] <3>.(0)[1:swapper/0]hdmi_oc_uevent_init start
[ 0.472308] <3>.(0)[1:swapper/0]loop: module loaded
[ 0.472910] <3>.(0)[1:swapper/0]zram: Added device: zram0
[ 0.473279] <3>.(0)[1:swapper/0]proc regulator for cpu0 not ready, retry.
[ 0.473294] <3>.(0)[1:swapper/0]mt8167-cpufreq mt8167-cpufreq: failed to initialize dvfs info for cpu0
[ 0.473995] <3>.(0)[1:swapper/0]gpufreq soc:mtgpu_freq: cannot get reg-vgpu
[ 0.474477] <3>.(0)[1:swapper/0]MT_SCHED: Init complete, device major number = 250
[ 0.474496] <3>.(0)[1:swapper/0][cpu_ntf] <00>c02ec080 (sched_cpu_notify)
[ 0.475149] <3>.(0)[1:swapper/0][MT AUXADC_probe3] get device tree info : start !!
[ 0.475258] <3>.(0)[1:swapper/0][AUXADC_AP] find node failed
[ 0.475262] <3>.(0)[1:swapper/0][MT AUXADC_AP] adc_channel_info_init : done !!
[ 0.475284] <3>.(0)[1:swapper/0]proc_create auxadc_debug_proc_fops
[ 0.475864] <3>.(0)[1:swapper/0]PSEUDO M4Udma mapping df8d78c0
[ 0.476352] <3>.(0)[1:swapper/0][PWM] get PWM1-main clock, df037d00
[ 0.476363] <3>.(0)[1:swapper/0][PWM] get PWM2-main clock, df037d80
[ 0.476375] <3>.(0)[1:swapper/0][PWM] get PWM3-main clock, df037e00
[ 0.476387] <3>.(0)[1:swapper/0][PWM] get PWM4-main clock, df037e80
[ 0.476402] <3>.(0)[1:swapper/0][PWM] get PWM5-main clock, df037f00
[ 0.476417] <3>.(0)[1:swapper/0][PWM] get PWM-HCLK-main clock, df037f80
[ 0.476438] <3>.(0)[1:swapper/0][PWM] get PWM-main clock, dfb50000
[ 0.476653] <3>.(0)[1:swapper/0][Accdet]accdet_mod_init begin!
[ 0.477544] <3>.(0)[1:swapper/0][Accdet]platform_driver_register done!
[ 0.477548] <3>.(0)[1:swapper/0][Accdet]accdet_mod_init done!
[ 0.477976] <3>.(0)[1:swapper/0]musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.478177] <3>.(0)[1:swapper/0][BOOT_COMMON] [create_sysfs] No atag,meta found !
[ 0.478353] <3>.(0)[1:swapper/0][DFRC] start to initialize fps policy
[ 0.478357] <3>.(0)[1:swapper/0][DFRC] register fps policy device
[ 0.478470] <3>.(0)[1:swapper/0][DFRC] register fps policy driver
[ 0.478712] <3>.(0)[1:swapper/0][DFRC] dfrc_init_kernel_policy
[ 0.478720] <3>.(0)[1:swapper/0][DFRC] reg_fps_policy: reg policy[3]
[ 0.478727] <3>.(0)[1:swapper/0][DFRC] reg_fps_policy: reg policy[2]
[ 0.478734] <3>.(0)[1:swapper/0][DFRC] reg_fps_policy: reg policy[4]
[ 0.478741] <3>.(0)[1:swapper/0][DFRC] reg_fps_policy: reg policy[5]
[ 0.479040] <3>.(0)[1:swapper/0]@mt_gpufreq_get_freq_by_idx: GPU DVFS not ready!
[ 0.479045] <3>.(0)[1:swapper/0]@mt_gpufreq_get_freq_by_idx: GPU DVFS not ready!
[ 0.479049] <3>.(0)[1:swapper/0]@mt_gpufreq_get_freq_by_idx: GPU DVFS not ready!
[ 0.482836] <3>.(0)[1:swapper/0][BLOCK_TAG] blockio: fail to allocate mtk_btag_pagelogger
[ 0.485761] <3>.(0)[1:swapper/0][GCPU] [GCPU_TA_Serivce] [68] Init Done:0!
[ 0.485763] <3>.(0)[1:swapper/0]------------[ cut here ]------------
[ 0.485776] <3>.(0)[1:swapper/0]WARNING: CPU: 0 PID: 1 at /work/pvt1.3/src/kernel/linux/v4.4/drivers/base/core.c:595 device_create_file+0x68/0x90()
[ 0.485780] <3>.(0)[1:swapper/0]Attribute state: write permission without 'store'
[ 0.485785] <3>.(0)[1:swapper/0]Modules linked in:
[ 0.485793] <3>-(0)[1:swapper/0]CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.22 #1
[ 0.485797] <3>-(0)[1:swapper/0]Hardware name: Generic DT based system
[ 0.485818] <3>-(0)[1:swapper/0][<c0016284>] (unwind_backtrace) from [<c0013204>] (show_stack+0x10/0x14)
[ 0.485831] <3>-(0)[1:swapper/0][<c0013204>] (show_stack) from [<c01ffa7c>] (dump_stack+0x70/0x8c)
[ 0.485844] <3>-(0)[1:swapper/0][<c01ffa7c>] (dump_stack) from [<c0027ae8>] (warn_slowpath_common+0x80/0xac)
[ 0.485855] <3>-(0)[1:swapper/0][<c0027ae8>] (warn_slowpath_common) from [<c0027b40>] (warn_slowpath_fmt+0x2c/0x3c)
[ 0.485867] <3>-(0)[1:swapper/0][<c0027b40>] (warn_slowpath_fmt) from [<c02b1f50>] (device_create_file+0x68/0x90)
[ 0.485881] <3>-(0)[1:swapper/0][<c02b1f50>] (device_create_file) from [<c050cbf4>] (switch_dev_register+0x8c/0xf4)
[ 0.485893] <3>-(0)[1:swapper/0][<c050cbf4>] (switch_dev_register) from [<c0a2f29c>] (mtk_cooler_fps_init+0xd8/0x2f4)
[ 0.485904] <3>-(0)[1:swapper/0][<c0a2f29c>] (mtk_cooler_fps_init) from [<c00098e4>] (do_one_initcall+0x5c/0x1fc)
[ 0.485915] <3>-(0)[1:swapper/0][<c00098e4>] (do_one_initcall) from [<c0a13da4>] (kernel_init_freeable+0x190/0x1d8)
[ 0.485927] <3>-(0)[1:swapper/0][<c0a13da4>] (kernel_init_freeable) from [<c0708498>] (kernel_init+0x8/0xf8)
[ 0.485938] <3>-(0)[1:swapper/0][<c0708498>] (kernel_init) from [<c000f858>] (ret_from_fork+0x14/0x3c)
[ 0.485956] <3>.(0)[1:swapper/0]---[ end trace c0b378dc805d7773 ]---
[ 0.485965] <3>.(0)[1:swapper/0]------------[ cut here ]------------
[ 0.485974] <3>.(0)[1:swapper/0]WARNING: CPU: 0 PID: 1 at /work/pvt1.3/src/kernel/linux/v4.4/drivers/base/core.c:595 device_create_file+0x68/0x90()
[ 0.485978] <3>.(0)[1:swapper/0]Attribute name: write permission without 'store'
[ 0.485983] <3>.(0)[1:swapper/0]Modules linked in:
[ 0.485990] <3>-(0)[1:swapper/0]CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 4.4.22 #1
[ 0.485994] <3>-(0)[1:swapper/0]Hardware name: Generic DT based system
[ 0.486006] <3>-(0)[1:swapper/0][<c0016284>] (unwind_backtrace) from [<c0013204>] (show_stack+0x10/0x14)
[ 0.486016] <3>-(0)[1:swapper/0][<c0013204>] (show_stack) from [<c01ffa7c>] (dump_stack+0x70/0x8c)
[ 0.486027] <3>-(0)[1:swapper/0][<c01ffa7c>] (dump_stack) from [<c0027ae8>] (warn_slowpath_common+0x80/0xac)
[ 0.486038] <3>-(0)[1:swapper/0][<c0027ae8>] (warn_slowpath_common) from [<c0027b40>] (warn_slowpath_fmt+0x2c/0x3c)
[ 0.486049] <3>-(0)[1:swapper/0][<c0027b40>] (warn_slowpath_fmt) from [<c02b1f50>] (device_create_file+0x68/0x90)
[ 0.486060] <3>-(0)[1:swapper/0][<c02b1f50>] (device_create_file) from [<c050cc08>] (switch_dev_register+0xa0/0xf4)
[ 0.486071] <3>-(0)[1:swapper/0][<c050cc08>] (switch_dev_register) from [<c0a2f29c>] (mtk_cooler_fps_init+0xd8/0x2f4)
[ 0.486081] <3>-(0)[1:swapper/0][<c0a2f29c>] (mtk_cooler_fps_init) from [<c00098e4>] (do_one_initcall+0x5c/0x1fc)
[ 0.486091] <3>-(0)[1:swapper/0][<c00098e4>] (do_one_initcall) from [<c0a13da4>] (kernel_init_freeable+0x190/0x1d8)
[ 0.486101] <3>-(0)[1:swapper/0][<c0a13da4>] (kernel_init_freeable) from [<c0708498>] (kernel_init+0x8/0xf8)
[ 0.486111] <3>-(0)[1:swapper/0][<c0708498>] (kernel_init) from [<c000f858>] (ret_from_fork+0x14/0x3c)
[ 0.486115] <3>.(0)[1:swapper/0]---[ end trace c0b378dc805d7774 ]---
[ 0.486274] <3>.(0)[1:swapper/0]tscpu_thermal_probe
[ 0.486441] <3>.(0)[1:swapper/0][Power/CPU_Thermal] [Thermal calibration] buf[0]=0x29048567, buf[1]=0x859d53f1, buf[2]=0x42aafe00
[ 0.491805] <3>.(0)[1:swapper/0]atf_log: inited
[ 0.491807] <3>.(0)[1:swapper/0]No atf_log_buffer!
[ 0.491820] <3>.(0)[1:swapper/0]atf_logger: probe of atf_logger failed with error -1
[ 0.492249] <3>.(0)[1:swapper/0][xo] dts default cap code: 0x0
[ 0.492281] <3>.(0)[1:swapper/0][xo] default cap_code: 0x30
[ 0.492286] <3>.(0)[1:swapper/0][xo] get xo efuse: a6000000
[ 0.512403] <3>.(0)[1:swapper/0][xo] current cap_code: 0x26
[ 0.512434] <3>.(0)[1:swapper/0][Preloader] BSI read: [0x25] = 0x6aab
[ 0.512456] <3>.(0)[1:swapper/0][Preloader] BSI read: [0x29] = 0x1
[ 0.512578] <3>.(0)[1:swapper/0][Preloader] BSI read: [0x29] = 0x0
[ 0.512590] <3>.(0)[1:swapper/0][xo] status: 0xf
[ 0.512626] <3>.(0)[1:swapper/0][xo] current cap code: 0x26
[ 0.512646] <3>.(0)[1:swapper/0]BOOTPROF: 512.640308:probe: probe=platform_drv_probe drv=mt_dts_xo(c0a94250) 20.473692ms
[ 0.512809] <3>.(0)[1:swapper/0]BOOTPROF: 512.804462:initcall: mt_xo_init 20.729538ms
[ 0.513604] <3>.(0)[1:swapper/0][Power/PMIC] MT6392 PMIC CID=0x2092
[ 0.513612] <3>.(0)[1:swapper/0][Power/PMIC] MT6392 Debug Status: Reg[0x7a]=0x0
[ 0.513620] <3>.(0)[1:swapper/0][Power/PMIC] MT6392 Debug Status: Reg[0x7c]=0x0
[ 0.514007] <3>.(0)[1:swapper/0][Power/PMIC] low power setting done...
[ 0.514027] <3>.(0)[1:swapper/0][Power/PMIC] MT6392 Reg[0x11a]=0x3b
[ 0.514034] <3>.(0)[1:swapper/0][Power/PMIC] MT6392 Reg[0x136]=0x1
[ 0.514042] <3>.(0)[1:swapper/0][pmic_buck_oc_enable] MT6392_BUCK_OC_CON0 0x258 = 0x6
[ 0.514063] <3>.(0)[1:swapper/0][pmic_buck_oc_enable] Clear Buck OC Flag, MT6392_BUCK_OC_CON0 0x258 = 0x0
[ 0.514079] <3>.(0)[1:swapper/0][pmic_buck_oc_enable] Enable Buck OC shutdown function...
[ 0.514114] <3>.(0)[1:swapper/0][pmic_ldo_cali_sw_bonding] Done...................
[ 0.514134] <3>.(0)[1:swapper/0][Power/PMIC] MT6392 Reg[0x70]=0x52
[ 0.514143] <3>.(0)[1:swapper/0][Power/PMIC] MT6392 Probe Done...................
[ 0.514326] <3>.(0)[1:swapper/0]mt6392-regulator mt6392-regulator: Chip ID = 0x2092
[ 0.523088] <3>.(0)[1:swapper/0]pinctrl doesnot have inter
[ 0.523772] <3>.(0)[1:swapper/0]Power/PMIC_Thermal: Reg(0x666)=0x4fca, Reg(0x668)=0x6
[ 0.525098] <3>.(0)[1:swapper/0]mt6397-misc mt6397-misc: enable 32k clock output!!!
[ 0.527340] <3>.(0)[1:swapper/0]tun: Universal TUN/TAP device driver, 1.6
[ 0.527345] <3>.(0)[1:swapper/0]tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.527828] <3>.(0)[1:swapper/0]usbcore: registered new interface driver usb-storage
[ 0.527879] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-alauda
[ 0.527918] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-cypress
[ 0.527956] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-datafab
[ 0.527998] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-freecom
[ 0.528036] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-isd200
[ 0.528074] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-jumpshot
[ 0.528113] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-karma
[ 0.528152] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-onetouch
[ 0.528190] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-sddr09
[ 0.528229] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-sddr55
[ 0.528267] <3>.(0)[1:swapper/0]usbcore: registered new interface driver ums-usbat
[ 0.528353] <3>.(0)[1:swapper/0]usbcore: registered new interface driver usbserial
[ 0.528397] <3>.(0)[1:swapper/0]usbcore: registered new interface driver option
[ 0.528432] <3>.(0)[1:swapper/0]usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.528480] <3>.(0)[1:swapper/0]usbcore: registered new interface driver trancevibrator
[ 0.529211] <3>.(0)[1:swapper/0]mousedev: PS/2 mouse device common for all mice
[ 0.533120] <3>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=5
[ 0.536168] <3>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=0
[ 0.539213] <3>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=0
[ 0.541256] <3>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=5
[ 0.544302] <3>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=3982
[ 0.544314] <3>.(0)[1:swapper/0][RTC] bbpu = 0x1, con = 0x84a7
[ 0.544321] <3>.(0)[1:swapper/0]rtc_first_boot_init
[ 1.550641] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=5
[ 1.554648] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=0
[ 1.558651] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=5
[ 1.561649] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=0
[ 1.565650] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=0
[ 1.579616] <0>.(0)[1:swapper/0][RTC] dcxo mode
[ 1.583277] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=5
[ 1.587279] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=0
[ 1.591280] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=0
[ 1.594278] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=5
[ 1.598291] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x0, ouput=4062
[ 1.599306] <0>.(0)[1:swapper/0][RTC] EOSC_Cali: TOP_CKCON1=0x40c0
[ 1.605180] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x24cf, ouput=811
[ 1.611248] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x24c7, ouput=688
[ 1.617315] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x24cb, ouput=750
[ 1.623383] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x24cd, ouput=781
[ 1.629462] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x24ce, ouput=796
[ 1.635530] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x24cd, ouput=781
[ 1.641598] <0>.(0)[1:swapper/0][RTC] get_frequency_meter: input=0x24ce, ouput=797
[ 1.642629] <0>.(0)[1:swapper/0][RTC] EOSC cali val = 0x24ce
[ 1.648181] <0>.(0)[1:swapper/0][RTC] MT6392_TOP_CKTST2 = 0x10
[ 1.649931] <0>.(0)[1:swapper/0][RTC] irqsta = 0x0, pdn1 = 0x0, pdn2 = 0x201, spar0 = 0xc0, spar1 = 0x800
[ 1.651239] <0>.(0)[1:swapper/0][RTC] new_spare0 = 0x0, new_spare1 = 0x1, new_spare2 = 0x1, new_spare3 = 0x1
[ 1.652578] <0>.(0)[1:swapper/0][RTC] bbpu = 0x1, con = 0x4a6, cali = 0x0
[ 1.653549] <0>.(0)[1:swapper/0][RTC] spar0 = 0xc0
[ 1.654311] <0>.(0)[1:swapper/0][RTC] rtc_bbpu_power_on done and bbpu = 0xd
[ 1.655627] <0>.(0)[1:swapper/0]mt6397-rtc mt6397-rtc: rtc core: registered mt6397-rtc as rtc0
[ 1.656811] <0>.(0)[1:swapper/0]BOOTPROF: 1656.805542:probe: probe=platform_drv_probe drv=mt6397-rtc(c0a9e9d0) 1126.813310ms
[ 1.658440] <0>.(0)[1:swapper/0]BOOTPROF: 1658.434849:initcall: mtk_rtc_driver_init 1128.844310ms
[ 1.661059] <0>.(0)[1:swapper/0]lirc_dev: IR Remote Control driver registered, major 246
[ 1.662180] <0>.(0)[1:swapper/0]IR Sharp protocol handler initialized
[ 1.663057] <0>.(0)[1:swapper/0]IR XMP protocol handler initialized
[ 1.664246] <0>.(0)[1:swapper/0]mtk_vcu 16000000.vcu: vcu iommudom: df8d1e4c,vcuid:0
[ 1.665498] <0>.(0)[1:swapper/0]mtk_vcu soc:vcu@1: vcu iommudom: df8d1e4c,vcuid:1
[ 1.666681] <0>.(0)[1:swapper/0]mtk_vcu soc:vcu@2: vcu iommudom: df8d1e4c,vcuid:2
[ 1.668880] <0>.(0)[1:swapper/0][MTK_V4L2] level=0 mtk_vcodec_probe(),351: decoder registered as /dev/video0
[ 1.671296] <0>.(0)[1:swapper/0][MTK_V4L2] level=0 mtk_vcodec_probe(),386: encoder registered as /dev/video1
[ 1.673090] <0>.(0)[1:swapper/0]mtk-mdp 14001000.rdma: Waiting cmdq driver ready...
[ 1.674521] <0>.(0)[1:swapper/0]usbcore: registered new interface driver uvcvideo
[ 1.675542] <0>.(0)[1:swapper/0]USB Video Class driver (1.1.1)
[ 1.676404] <0>.(0)[1:swapper/0]MTK_WDT_NONRST_REG(0)
[ 1.677418] <0>.(0)[1:swapper/0]mtk-wdt 10007000.toprgu: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.679007] <0>.(0)[1:swapper/0]device-mapper: uevent: version 1.0.3
[ 1.680132] <0>.(0)[1:swapper/0]device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 1.681773] <0>.(0)[1:swapper/0]cpuidle: enable-method property 'psci' found operations
[ 1.683068] <0>.(0)[1:swapper/0]cpuidle: enable-method property 'psci' found operations
[ 1.684353] <0>.(0)[1:swapper/0]cpuidle: enable-method property 'psci' found operations
[ 1.685664] <0>.(0)[1:swapper/0]cpuidle: enable-method property 'psci' found operations
[ 1.688248] <0>.(0)[1:swapper/0]mtk-msdc 11120000.mmc: Regulator set error -22: 3300000 - 3300000
[ 1.724429] <0>.(0)[1:swapper/0]BOOTPROF: 1724.422465:probe: probe=platform_drv_probe drv=mtk-msdc(c0aa365c) 36.618539ms
[ 1.726436] <0>.(0)[1:swapper/0]BOOTPROF: 1726.431234:initcall: mt_msdc_driver_init 39.359692ms
[ 1.728287] <2>.(2)[1:swapper/0][msdc][msdc_debug_proc_init]: create /proc/msdc_debug
[ 1.729359] <2>.(2)[1:swapper/0][msdc][msdc_debug_proc_init]: create /proc/msdc_help
[ 1.730967] <2>.(2)[1:swapper/0]hidraw: raw HID events driver (C) Jiri Kosina
[ 1.733220] <2>.(2)[1:swapper/0]usbcore: registered new interface driver usbhid
[ 1.734218] <2>.(2)[1:swapper/0]usbhid: USB HID core driver
[ 1.735268] <2>.(2)[1:swapper/0]ashmem: initialized
[ 1.737942] <2>.(2)[1:swapper/0]usbcore: registered new interface driver snd-usb-audio
[ 1.741031] <2>.(2)[1:swapper/0]mtk-afe-pcm 11140000.audio-controller: MTK AFE driver initialized.
[ 1.742622] <2>.(2)[1:swapper/0](NULL device *): mt8167_evb_dev_probe
[ 1.743510] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: mt8167_evb_gpio_probe
[ 1.744490] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: mt8167_evb_gpio_probe Can't find pinctrl state default -19
[ 1.745860] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: mt8167_evb_gpio_probe Can't find pinctrl state extamp_on -19
[ 1.747251] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: mt8167_evb_gpio_probe Can't find pinctrl state extamp_off -19
[ 1.774118] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> DL1 mapping ok
[ 1.775389] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> VUL mapping ok
[ 1.776609] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: i2s-hifi <-> HDMI mapping ok
[ 1.777736] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> AWB mapping ok
[ 1.779008] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> DL2 mapping ok
[ 1.780256] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> DAI mapping ok
[ 1.781479] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> TDM_IN mapping ok
[ 1.782701] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> I2S mapping ok
[ 1.783888] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> 2ND I2S mapping ok
[ 1.785135] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: mt8167-codec-dai <-> INT ADDA mapping ok
[ 1.786361] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> HDMIO mapping ok
[ 1.787563] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> DL Input mapping ok
[ 1.788808] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> MRG BT mapping ok
[ 1.790029] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> PCM0 mapping ok
[ 1.791222] <2>.(2)[1:swapper/0]mt8167-mt6392 sound: snd-soc-dummy-dai <-> TDM_IN_IO mapping ok
[ 1.793160] <2>.(2)[1:swapper/0]hdmi-audio-codec hdmi-audio-codec: ASoC: Failed to create Playback debugfs file
[ 1.796346] <2>.(2)[1:swapper/0]BOOTPROF: 1796.338311:probe: probe=platform_drv_probe drv=mt8167-mt6392(c0aadd50) 53.710770ms
[ 1.798045] <2>.(2)[1:swapper/0]BOOTPROF: 1798.039927:initcall: mt8167_evb_mach_driver_init 55.639462ms
[ 1.799532] <2>.(2)[1:swapper/0]Mirror/redirect action on
[ 1.800291] <2>.(2)[1:swapper/0]u32 classifier
[ 1.800898] <2>.(2)[1:swapper/0] Performance counters on
[ 1.801654] <2>.(2)[1:swapper/0] input device check on
[ 1.802386] <2>.(2)[1:swapper/0] Actions configured
[ 1.803102] <2>.(2)[1:swapper/0]Netfilter messages via NETLINK v0.30.
[ 1.804022] <2>.(2)[1:swapper/0]nf_conntrack version 0.5.0 (16008 buckets, 64032 max)
[ 1.805518] <2>.(2)[1:swapper/0]ctnetlink v0.93: registering with nfnetlink.
[ 1.806988] <2>.(2)[1:swapper/0]xt_time: kernel timezone is -0000
[ 1.807970] <2>.(2)[1:swapper/0]ipip: IPv4 over IPv4 tunneling driver
[ 1.809520] <2>.(2)[1:swapper/0]ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.810607] <2>.(2)[1:swapper/0]arp_tables: (C) 2002 David S. Miller
[ 1.811487] <2>.(2)[1:swapper/0]Initializing XFRM netlink socket
[ 1.812881] <2>.(2)[1:swapper/0]NET: Registered protocol family 10
[ 1.814798] <2>.(2)[1:swapper/0]mip6: Mobile IPv6
[ 1.815464] <2>.(2)[1:swapper/0]ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.816601] <2>.(2)[1:swapper/0]sit: IPv6 over IPv4 tunneling driver
[ 1.818539] <2>.(2)[1:swapper/0]NET: Registered protocol family 17
[ 1.819398] <2>.(2)[1:swapper/0]NET: Registered protocol family 15
[ 1.820272] <2>.(2)[1:swapper/0]bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.822233] <2>.(2)[1:swapper/0]Bridge firewalling registered
[ 1.823019] <2>.(2)[1:swapper/0]8021q: 802.1Q VLAN Support v1.8
[ 1.824108] <2>.(2)[1:swapper/0]Registering SWP/SWPB emulation handler
[ 1.825618] <2>.(2)[1:swapper/0]bootconsole [uart0] disabled
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
You can’t perform that action at this time.