config.g

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Sun Aug 04 2019 19:23:55 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
G90                                         ; Send absolute coordinates...
M83                                         ; ...but relative extruder moves
M665 L360.22:360.22:360.22 R160 B125 H411.7 X0 Y0 Z0 diagonal rod length, delta radius, printable radius and homed height
M666 X0 Y0 Z0                               ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 P"Frankenkossel"                       ; Set machine name
M552 S1                                     ; Enable network

M586 P0 S1                                  ; Enable HTTP
M586 P1 S0                                  ; Disable FTP
M586 P2 S0                                  ; Disable Telnet

; Drives
M569 P0 S1                                  ; Physical drive 0 goes forwards
M569 P1 S1                                  ; Physical drive 1 goes forwards
M569 P2 S1                                  ; Physical drive 2 goes forwards
M569 P3 S0                                  ; Physical drive 3 goes backwards (extruder)
M350 X16 Y16 Z16 E16 I1                     ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E141.00             ; Set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00    ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; Set maximum speeds (mm/min)
M201 X2000.00 Y2000.00 Z2000.00 E2000.00    ; Set accelerations (mm/s^2)
M906 X1000.00 Y1000.00 Z1000.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                     ; Set idle timeout

; Axis Limits
M208 Z0:410.45                              ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S1                            ; Set active high endstops

; Z-Probe
M558 P5 R0.4 H3 F360 T6000                 ; Set Z probe type to effector and the dive height + speeds
G31 P500 X0 Y0 Z -0.199                    ; Set Z probe trigger value, offset and trigger height
M557 R111 S20                              ; Define mesh grid

; Heaters
M307 H0 B0 S1.00                            ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R4700                 ; Set thermistor + ADC parameters for heater 0
M143 H0 S80                                 ; Set temperature limit for heater 0 to 80C
M305 P1 T100000 B4725 C7.06e-8              ; Set thermistor + ADC parameters for heater 1

M143 H1 S240                                ; Set temperature limit for heater 1 to 240C

; Fans
M106 P0 S0 I0 F500 H T45                    ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45                   ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45                   ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 S"Nozzle" D0 H1                     ; Define tool 0
G10 P0 X0 Y0 Z0                             ; Set tool 0 axis offsets
G10 P0 R0 S0                                ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured

; Miscellaneous
T0                                          ; Select first tool
M80                                         ; ATX Power on

; load values from config-override.g
M501