v-core pro config.g

config.g

; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Jan 31 2020 14:54:13 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90                                                   ; send absolute coordinates...
M83                                                   ; ...but relative extruder moves
M550 P"vcore-pro"                                        ; set printer name

M669 K1                                               ; select CoreXY mode

; Drives
M569 P0.0 S0                                          ; physical drive 0.0 goes backwards (X)
M569 P0.1 S0                                          ; physical drive 0.1 goes backwards (Y)
M569 P0.3 S1                                          ; physical drive 0.3 goes forwards  (Z1)
M569 P0.4 S1                                          ; physical drive 0.4 goes forwards  (Z2)
M569 P0.5 S1                                          ; physical drive 0.5 goes forwards  (Z3)
M569 P10.0 S1                                         ; physical drive 10.0 goes forwards (E -- tool board)
M584 X0.0 Y0.1 Z0.3:0.4:0.5                           ; set drive mapping -- 3HC
M584 E10.0                                            ; set drive mapping -- tool board
M350 X16 Y16 Z16 E16 I1                               ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z1600.00 E415.00                  ; set steps per mm

M566 X900.00 Y900.00 Z60.00 E600.00 P1                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00               ; set maximum speeds (mm/min)
M201 X6000.00 Y6000.00 Z20.00 E120.00                 ; set accelerations (mm/s^2)


M906 X800 Y800 Z800 E1000 I30                         ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                               ; Set idle timeout

; Axis Limits
M208 X-150 Y-150 Z0 S1                                ; set axis minima
M208 X150 Y150 Z330 S0                                ; set axis maxima
M206 X-10 Y-10

; Endstops
M574 X1 Y2 S3 ; use stall guard for  XY endstops (X min, y max)
M574 Z1 S2                                            ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P8 C"10.io1.in" H5 F120 T6000                    ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X-35 Y0 Z1.0                                 ; set Z probe trigger value, offset and trigger height
M557 X-140:140 Y-140:140 P6                           ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138 A"Bed"   ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 Q10                                ; create bed heater output on out2 and map it to sensor 0
M143 H0 S120                                          ; set temperature limit for heater 0 to 120C
M307 H0 B1 S1.00                                      ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                               ; map heated bed to heater 0

M308 S1 P"10.temp0" Y"thermistor" B4725 C7.06e-8  A"Tool 0" ; Semitec on toolboard with address 10
M950 H1 C"10.out0" T1                                 ; create nozzle heater output on out1 and map it to sensor 1
M143 H1 S295                                          ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00                                      ; disable bang-bang mode for heater  and set PWM limit

; Fans
M950 F0 C"10.out1" Q500                                  ; create fan 0 on pin out3 and set its frequency
M106 P0 S0 H-1                                        ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"10.out2" Q500                                  ; create fan 1 on pin out4 and set its frequency
M106 P1 S1 H1 T45                                     ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                      ; define tool 0
G10 P0 X0 Y0 Z0                                       ; set tool 0 axis offsets
G10 P0 R0 S0                                          ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Adjustment screw positions
; M671 X-155:-155:155:155 Y-155:155:155:-155
; Z Lead Screw positions
M671 X-180:0:180 Y-50:210:-50


; Load config-override.g
M501

; Linear Advance
M572 D0 S0.03

; PanelDue
M575 P1 B57600 S1
M575 P1 B57600 S1