Starfive VisionFive2 power up serial output after the necessary flashcp

gistfile1.txt

picocom v3.1

port is        : /dev/ttyUSB0
flowcontrol    : none
baudrate is    : 115200
parity is      : none
databits are   : 8
stopbits are   : 1
escape is      : C-a
local echo is  : no
noinit is      : no
noreset is     : no
hangup is      : no
nolock is      : no
send_cmd is    : sz -vv
receive_cmd is : rz -vv -E
imap is        : 
omap is        : 
emap is        : crcrlf,delbs,
logfile is     : none
initstring     : none
exit_after is  : not set
exit is        : no

Type [C-a] [C-h] to see available commands
Terminal ready

U-Boot SPL 2021.10 (May 09 2024 - 22:45:24 +0800)
LPDDR4: 8G version: g8ad50857.
Trying to boot from SPI

OpenSBI v1.2
   ____                    _____ ____ _____
  / __ \                  / ____|  _ \_   _|
 | |  | |_ __   ___ _ __ | (___ | |_) || |
 | |  | | '_ \ / _ \ '_ \ \___ \|  _ < | |
 | |__| | |_) |  __/ | | |____) | |_) || |_
  \____/| .__/ \___|_| |_|_____/|___\0/_____|
        | |
        |_|

Platform Name             : StarFive VisionFive V2
Platform Features         : medeleg
Platform HART Count       : 5
Platform IPI Device       : aclint-mswi
Platform Timer Device     : aclint-mtimer @ 4000000Hz
Platform Console Device   : uart8250
Platform HSM Device       : ---
Platform PMU Device       : ---
Platform Reboot Device    : pm-reset
Platform Shutdown Device  : pm-reset
Platform Suspend Device   : ---
Firmware Base             : 0x40000000
Firmware Size             : 392 KB
Firmware RW Offset        : 0x40000
Runtime SBI Version       : 1.0

Domain0 Name              : root
Domain0 Boot HART         : 1
Domain0 HARTs             : 0*,1*,2*,3*,4*
Domain0 Region00          : 0x0000000002000000-0x000000000200ffff M: (I,R,W) S/U: ()
Domain0 Region01          : 0x0000000040000000-0x000000004003ffff M: (R,X) S/U: ()
Domain0 Region02          : 0x0000000040040000-0x000000004007ffff M: (R,W) S/U: ()
Domain0 Region03          : 0x0000000000000000-0xffffffffffffffff M: (R,W,X) S/U: (R,W,X)
Domain0 Next Address      : 0x0000000040200000
Domain0 Next Arg1         : 0x0000000042200000
Domain0 Next Mode         : S-mode
Domain0 SysReset          : yes
Domain0 SysSuspend        : yes

Boot HART ID              : 1
Boot HART Domain          : root
Boot HART Priv Version    : v1.11
Boot HART Base ISA        : rv64imafdcbx
Boot HART ISA Extensions  : none
Boot HART PMP Count       : 8
Boot HART PMP Granularity : 4096
Boot HART PMP Address Bits: 34
Boot HART MHPM Count      : 2
Boot HART MIDELEG         : 0x0000000000000222
Boot HART MEDELEG         : 0x000000000000b109


U-Boot 2021.10 (May 09 2024 - 22:45:24 +0800), Build: jenkins-github_visionfive2_6.6-1

CPU:   rv64imacu_zba_zbb
Model: StarFive VisionFive V2
DRAM:  8 GiB
MMC:   sdio0@16010000: 0, sdio1@16020000: 1
Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment

StarFive EEPROM format v2

--------EEPROM INFO--------
Vendor : StarFive Technology Co., Ltd.
Product full SN: VF7110B1-2253-D008E000-00002621
data version: 0x2
PCB revision: 0xb2
BOM revision: A
Ethernet MAC0 address: 6c:cf:39:00:36:43
Ethernet MAC1 address: 6c:cf:39:00:36:44
--------EEPROM INFO--------

In:    serial
Out:   serial
Err:   serial
Model: StarFive VisionFive V2
Net:   eth0: ethernet@16030000, eth1: ethernet@16040000
Hit any key to stop autoboot:  2  1  0 
switch to partitions #0, OK
mmc1 is current device
Try booting from MMC1 ...
Failed to load 'vf2_uEnv.txt'
## Warning: Input data exceeds 1048576 bytes - truncated
## Info: input data size = 1048578 = 0x100002
## Error: "boot2" not defined
Card did not respond to voltage select! : -110
starfive_pcie pcie@2B000000: Port link up.
starfive_pcie pcie@2B000000: Starfive PCIe bus probed.
PCI: Failed autoconfig bar 10
starfive_pcie pcie@2C000000: Port link down.
starfive_pcie pcie@2C000000: Starfive PCIe bus probed.
PCI: Failed autoconfig bar 10

Device 0: unknown device

Device 0: unknown device
Tring booting distro ...
switch to partitions #0, OK
mmc1 is current device
Try booting from MMC1 ...
419 bytes read in 4 ms (101.6 KiB/s)
Retrieving file: /extlinux/extlinux.conf
1386 bytes read in 7 ms (193.4 KiB/s)
U-Boot menu
1:	Debian GNU/Linux bookworm/sid 6.6.20-starfive
2:	Debian GNU/Linux bookworm/sid 6.6.20-starfive (rescue target)
3:	Debian GNU/Linux bookworm/sid 5.15.0-starfive
4:	Debian GNU/Linux bookworm/sid 5.15.0-starfive (rescue target)
Enter choice: 1:	Debian GNU/Linux bookworm/sid 6.6.20-starfive
Retrieving file: /initrd.img-6.6.20-starfive
10402331 bytes read in 454 ms (21.9 MiB/s)
Retrieving file: /vmlinuz-6.6.20-starfive
9521399 bytes read in 417 ms (21.8 MiB/s)
append: root=/dev/mmcblk1p4 rw console=tty0 console=ttyS0,115200 earlycon rootwait stmmaceth=chain_mode:1 selinux=0
Retrieving file: /dtbs/6.6.20/starfive/jh7110-starfive-visionfive-2-v1.3b.dtb
54960 bytes read in 12 ms (4.4 MiB/s)
   Uncompressing Kernel Image
## Flattened Device Tree blob at 46000000
   Booting using the fdt blob at 0x46000000
   Using Device Tree in place at 0000000046000000, end 00000000460106af

Starting kernel ...

clk u5_dw_i2c_clk_core already disabled
clk u5_dw_i2c_clk_apb already disabled
[    0.000000] Linux version 6.6.20-starfive (root@leo-virtual-machine) (riscv64-unknown-linux-gnu-gcc (g2ee5e430018) 12.2.0, GNU ld (GNU Binutils) 2.40.0.20230214) #1 SMP Sun May  5 22:39:25 CST 2024
[    0.000000] Machine model: StarFive VisionFive 2 v1.3B
[    0.000000] SBI specification v1.0 detected
[    0.000000] SBI implementation ID=0x1 Version=0x10002
[    0.000000] SBI TIME extension detected
[    0.000000] SBI IPI extension detected
[    0.000000] SBI RFENCE extension detected
[    0.000000] SBI SRST extension detected
[    0.000000] earlycon: uart0 at MMIO32 0x0000000010000000 (options '115200n8')
[    0.000000] printk: bootconsole [uart0] enabled
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 1536 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] OF: reserved mem: 0x0000000070000000..0x00000000cfffffff (1572864 KiB) map reusable linux,cma
[    0.000000] OF: reserved mem: 0x0000000040000000..0x000000004007ffff (512 KiB) nomap non-reusable opensbi@40000000
[    0.000000] OF: reserved mem: 0x0000000069c00000..0x000000006bbffffe (32767 KiB) map non-reusable xrpbuffer@f0000000
[    0.000000] OF: reserved mem: 0x000000006ce00000..0x000000006e3fffff (22528 KiB) map non-reusable e24@c0000000
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000023fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000004007ffff]
[    0.000000]   node   0: [mem 0x0000000040080000-0x000000023fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000023fffffff]
[    0.000000] SBI HSM extension detected
[    0.000000] CPU with hartid=0 is not available
[    0.000000] Falling back to deprecated "riscv,isa"
[    0.000000] riscv: base ISA extensions acdfim
[    0.000000] riscv: ELF capabilities acdfim
[    0.000000] percpu: Embedded 19 pages/cpu s39864 r8192 d29768 u77824
[    0.000000] Kernel command line: root=/dev/mmcblk1p4 rw console=tty0 console=ttyS0,115200 earlycon rootwait stmmaceth=chain_mode:1 selinux=0
[    0.000000] Unknown kernel command line parameters "selinux=0", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2068480
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB)
[    0.000000] Memory: 6512796K/8388608K available (11564K kernel code, 5045K rwdata, 6144K rodata, 2213K init, 764K bss, 302948K reserved, 1572864K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] rcu: 	RCU debug extended QS entry/exit.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] riscv-intc: 64 local interrupts mapped
[    0.000000] plic: interrupt-controller@c000000: mapped 136 interrupts with 4 handlers for 9 contexts.
[    0.000000] riscv: providing IPIs using SBI IPI extension
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404240 ns
[    0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns
[    0.009038] Console: colour dummy device 80x25
[    0.013916] printk: console [tty0] enabled
[    0.018975] Calibrating delay loop (skipped), value calculated using timer frequency.. 8.00 BogoMIPS (lpj=40000)
[    0.030170] pid_max: default: 32768 minimum: 301
[    0.035541] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.044021] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.053721] CPU node for /cpus/cpu@0 exist but the possible cpu range is :0-3
[    0.062837] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.071264] riscv: ELF compat mode unsupported
[    0.071274] ASID allocator disabled (0 bits)
[    0.080983] rcu: Hierarchical SRCU implementation.
[    0.086258] rcu: 	Max phase no-delay instances is 1000.
[    0.092279] EFI services will not be available.
[    0.097649] smp: Bringing up secondary CPUs ...
[    0.157308] cpu1: Ratio of byte access time to unaligned word access is 0.01, unaligned accesses are slow
[    0.227344] cpu2: Ratio of byte access time to unaligned word access is 0.01, unaligned accesses are slow
[    0.297381] cpu3: Ratio of byte access time to unaligned word access is 0.01, unaligned accesses are slow
[    0.307998] smp: Brought up 1 node, 4 CPUs
[    0.314962] devtmpfs: initialized
[    0.327263] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.338103] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.384670] pinctrl core: initialized pinctrl subsystem
[    0.391646] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.398933] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    0.406914] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.416153] thermal_sys: Registered thermal governor 'step_wise'
[    0.416200] cpuidle: using governor menu
[    0.482849] cpu0: Ratio of byte access time to unaligned word access is 0.01, unaligned accesses are slow
[    0.493844] CCACHE: DataError @ 0x00000000.08040110
[    0.499280] CCACHE: DataFail @ 0x00000000.08040270
[    0.504667] CCACHE: 8 banks, 16 ways, sets/bank=256, bytes/block=64
[    0.511555] CCACHE: max_line=2047, 64 bytes/line, 131072 bytes/way
[    0.518362] CCACHE: Index of the largest way enabled: 15
[    0.524197] pL2CACHE_PMU: perfmon-counters: 64 for CPU 0
[    0.530188] pL2CACHE_PMU: perfmon-counters: 64 for CPU 1
[    0.536159] pL2CACHE_PMU: perfmon-counters: 64 for CPU 2
[    0.542144] pL2CACHE_PMU: perfmon-counters: 64 for CPU 3
[    0.554964] platform soc: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
[    0.577481] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[    0.584969] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
[    0.591853] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[    0.599317] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
[    0.607486] SCSI subsystem initialized
[    0.612023] usbcore: registered new interface driver usbfs
[    0.618082] usbcore: registered new interface driver hub
[    0.623967] usbcore: registered new device driver usb
[    0.629805] mc: Linux media interface: v0.10
[    0.634560] videodev: Linux video capture interface: v2.00
[    0.640985] Advanced Linux Sound Architecture Driver Initialized.
[    0.648238] Bluetooth: Core ver 2.22
[    0.652191] NET: Registered PF_BLUETOOTH protocol family
[    0.658044] Bluetooth: HCI device and connection manager initialized
[    0.665028] Bluetooth: HCI socket layer initialized
[    0.670399] Bluetooth: L2CAP socket layer initialized
[    0.675961] Bluetooth: SCO socket layer initialized
[    0.681821] vgaarb: loaded
[    0.685121] clocksource: Switched to clocksource riscv_clocksource
[    0.692245] FS-Cache: Loaded
[    0.705252] NET: Registered PF_INET protocol family
[    0.711767] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.731993] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.741664] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.750207] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.759725] TCP bind hash table entries: 65536 (order: 10, 4194304 bytes, linear)
[    0.774534] TCP: Hash tables configured (established 65536 bind 65536)
[    0.782054] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
[    0.790061] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
[    0.798720] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.805540] RPC: Registered named UNIX socket transport module.
[    0.812048] RPC: Registered udp transport module.
[    0.817236] RPC: Registered tcp transport module.
[    0.822401] RPC: Registered tcp-with-tls transport module.
[    0.828439] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.836917] PCI: CLS 0 bytes, default 64
[    0.841676] Unpacking initramfs...
[    0.842530] Initialise system trusted keyrings
[    0.850571] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[    0.858313] NFS: Registering the id_resolver key type
[    0.863927] Key type id_resolver registered
[    0.868550] Key type id_legacy registered
[    0.872994] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.880380] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    0.888547] ntfs: driver 2.1.32 [Flags: R/W].
[    0.893388] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.900440] fuse: init (API version 7.39)
[    0.983473] NET: Registered PF_ALG protocol family
[    0.988802] Key type asymmetric registered
[    0.993312] Asymmetric key parser 'x509' registered
[    0.998775] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.006926] io scheduler mq-deadline registered
[    1.011920] io scheduler kyber registered
[    1.016415] io scheduler bfq registered
[    1.106282] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    1.119910] random: crng init done
[    1.141121] loop: module loaded
[    1.147720] spi-nor spi0.0: gd25lq128d (16384 Kbytes)
[    2.535561] Freeing initrd memory: 10156K
[    2.558885] 4 fixed-partitions partitions found on MTD device 13010000.spi.0
[    2.566688] Creating 4 MTD partitions on "13010000.spi.0":
[    2.572727] 0x000000000000-0x000000080000 : "spl"
[    2.579602] 0x0000000f0000-0x000000100000 : "uboot-env"
[    2.586840] 0x000000100000-0x000000500000 : "uboot"
[    2.593671] 0x000000600000-0x000001000000 : "reserved-data"
[    2.604075] CAN device driver interface
[    2.609561] starfive-dwmac 16030000.ethernet: User ID: 0x41, Synopsys ID: 0x52
[    2.617554] starfive-dwmac 16030000.ethernet: 	DWMAC4/5
[    2.623304] starfive-dwmac 16030000.ethernet: DMA HW capability register supported
[    2.631651] starfive-dwmac 16030000.ethernet: RX Checksum Offload Engine supported
[    2.639992] starfive-dwmac 16030000.ethernet: Wake-Up On Lan supported
[    2.647257] starfive-dwmac 16030000.ethernet: TSO supported
[    2.653388] starfive-dwmac 16030000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.662303] starfive-dwmac 16030000.ethernet: Enabled L3L4 Flow TC (entries=1)
[    2.670268] starfive-dwmac 16030000.ethernet: Enabled RFS Flow TC (entries=10)
[    2.678229] starfive-dwmac 16030000.ethernet: TSO feature enabled
[    2.684932] starfive-dwmac 16030000.ethernet: Using 40/40 bits DMA host/device width
[    2.710188] starfive-dwmac 16040000.ethernet: User ID: 0x41, Synopsys ID: 0x52
[    2.718199] starfive-dwmac 16040000.ethernet: 	DWMAC4/5
[    2.723951] starfive-dwmac 16040000.ethernet: DMA HW capability register supported
[    2.732306] starfive-dwmac 16040000.ethernet: RX Checksum Offload Engine supported
[    2.740652] starfive-dwmac 16040000.ethernet: Wake-Up On Lan supported
[    2.747920] starfive-dwmac 16040000.ethernet: TSO supported
[    2.754052] starfive-dwmac 16040000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    2.762970] starfive-dwmac 16040000.ethernet: Enabled L3L4 Flow TC (entries=1)
[    2.770933] starfive-dwmac 16040000.ethernet: Enabled RFS Flow TC (entries=10)
[    2.778895] starfive-dwmac 16040000.ethernet: TSO feature enabled
[    2.785614] starfive-dwmac 16040000.ethernet: Using 40/40 bits DMA host/device width
[    2.809676] Intel(R) Wireless WiFi driver for Linux
[    2.817482] usbcore: registered new interface driver uas
[    2.823367] usbcore: registered new interface driver usb-storage
[    2.845570] starfive-rtc 17040000.rtc: registered as rtc0
[    2.851535] starfive-rtc 17040000.rtc: setting system clock to 2001-01-01T00:00:00 UTC (978307200)
[    2.861522] i2c_dev: i2c /dev entries driver
[    2.866662] Error: Driver 'imx219' is already registered, aborting...
[    2.873794] usbcore: registered new interface driver uvcvideo
[    2.882943] sdhci: Secure Digital Host Controller Interface driver
[    2.889781] sdhci: Copyright(c) Pierre Ossman
[    2.894616] Synopsys Designware Multimedia Card Interface Driver
[    2.901551] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.909205] clocksource: jh7110-timer.ch0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    2.920464] clocksource: jh7110-timer.ch1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    2.931728] clocksource: jh7110-timer.ch2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    2.942974] clocksource: jh7110-timer.ch3: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    2.954469] usbcore: registered new interface driver usbhid
[    2.960626] usbhid: USB HID core driver
[    2.964881] SPI driver st-accel-spi has no spi_device_id for st,lis302dl-spi
[    2.972668] SPI driver st-accel-spi has no spi_device_id for st,lis3lv02dl-accel
[    2.980816] SPI driver st-accel-spi has no spi_device_id for st,lis3dh-accel
[    2.988581] SPI driver st-accel-spi has no spi_device_id for st,lsm330d-accel
[    2.996438] SPI driver st-accel-spi has no spi_device_id for st,lsm330dl-accel
[    3.004381] SPI driver st-accel-spi has no spi_device_id for st,lsm330dlc-accel
[    3.012436] SPI driver st-accel-spi has no spi_device_id for st,lis331dlh-accel
[    3.020485] SPI driver st-accel-spi has no spi_device_id for st,lsm330-accel
[    3.028251] SPI driver st-accel-spi has no spi_device_id for st,lsm303agr-accel
[    3.036302] SPI driver st-accel-spi has no spi_device_id for st,lis2dh12-accel
[    3.044246] SPI driver st-accel-spi has no spi_device_id for st,lng2dm-accel
[    3.052011] SPI driver st-accel-spi has no spi_device_id for st,h3lis331dl-accel
[    3.060157] SPI driver st-accel-spi has no spi_device_id for st,lis331dl-accel
[    3.068120] SPI driver st-accel-spi has no spi_device_id for st,lsm303c-accel
[    3.076234] riscv-pmu-sbi: SBI PMU extension is available
[    3.082196] riscv-pmu-sbi: 16 firmware and 4 hardware counters
[    3.088641] riscv-pmu-sbi: Perf sampling/filtering is not supported as sscof extension is not available
[    3.099388] usbcore: registered new interface driver snd-usb-audio
[    3.114280] NET: Registered PF_INET6 protocol family
[    3.121258] Segment Routing with IPv6
[    3.125361] In-situ OAM (IOAM) with IPv6
[    3.129777] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    3.136967] NET: Registered PF_PACKET protocol family
[    3.142528] can: controller area network core
[    3.147421] NET: Registered PF_CAN protocol family
[    3.152698] can: raw protocol
[    3.156004] can: broadcast manager protocol
[    3.160614] can: netlink gateway - max_hops=1
[    3.165673] Bluetooth: RFCOMM TTY layer initialized
[    3.171049] Bluetooth: RFCOMM socket layer initialized
[    3.176747] Bluetooth: RFCOMM ver 1.11
[    3.180884] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.186745] Bluetooth: BNEP filters: protocol multicast
[    3.192498] Bluetooth: BNEP socket layer initialized
[    3.198066] lib80211: common routines for IEEE802.11 drivers
[    3.204376] 9pnet: Installing 9P2000 support
[    3.209190] Key type dns_resolver registered
[    3.235674] Loading compiled-in X.509 certificates
[    3.276923] @@ dev ptr:ffffffd8c0179000/1500/1
[    3.282138] PVR_K:  1: Read BVNC 36.50.54.182 from HW device registers
[    3.289392] PVR_K:  1: RGX Device registered BVNC 36.50.54.182 with 1 core in the system
[    3.304282] PVR_K:  1: RGX Firmware image 'rgx.fw.36.50.54.182' loaded
[    3.316079] PVR_K:  1: Shader binary image 'rgx.sh.36.50.54.182' loaded
[    3.326364] [drm] Initialized pvr 1.19.6345021 20170530 for 18000000.gpu on minor 0
[    3.335419] pl08xdmac 16008000.dma-controller: initialized 8 virtual memcpy channels
[    3.343960] pl08xdmac 16008000.dma-controller: initialized 16 virtual slave channels
[    3.354382] debugfs: Directory '16008000.dma-controller' with parent 'dmaengine' already present!
[    3.364176] pl08xdmac 16008000.dma-controller: DMA: PL080 rev0 at 0x16008000 irq 33
[    3.373464] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    3.383587] starfive-jh7110-sys-pinctrl 13040000.pinctrl: StarFive GPIO chip registered 64 GPIOs
[    3.394366] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    3.404408] starfive-jh7110-aon-pinctrl 17020000.pinctrl: StarFive GPIO chip registered 4 GPIOs
[    3.414901] pcie-starfive 940000000.pcie: host bridge /soc/pcie@940000000 ranges:
[    3.423208] pcie-starfive 940000000.pcie:      MEM 0x0030000000..0x0037ffffff -> 0x0030000000
[    3.432617] pcie-starfive 940000000.pcie:      MEM 0x0900000000..0x093fffffff -> 0x0900000000
[    3.675144] pcie-starfive 940000000.pcie: port link up
[    3.682126] pcie-starfive 940000000.pcie: PCI host bridge to bus 0000:00
[    3.689552] pci_bus 0000:00: root bus resource [bus 00-ff]
[    3.695610] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    3.703173] pci_bus 0000:00: root bus resource [mem 0x900000000-0x93fffffff pref]
[    3.711451] pci 0000:00:00.0: [1556:1111] type 01 class 0x060400
[    3.718153] pci 0000:00:00.0: supports D1 D2
[    3.722853] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    3.733710] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[    3.740367] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    3.747944] pci 0000:01:00.0: PME# supported from D0 D3cold
[    3.754302] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    3.761615] pci 0000:00:00.0: BAR 8: assigned [mem 0x30000000-0x300fffff]
[    3.769102] pci 0000:01:00.0: BAR 0: assigned [mem 0x30000000-0x30000fff 64bit]
[    3.777175] pci 0000:00:00.0: PCI bridge to [bus 01]
[    3.782640] pci 0000:00:00.0:   bridge window [mem 0x30000000-0x300fffff]
[    3.790225] pci 0000:01:00.0: enabling device (0000 -> 0002)
[    3.796779] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    3.802554] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[    3.811056] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000000000000890
[    3.821657] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    3.827435] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    3.835597] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    3.843268] hub 1-0:1.0: USB hub found
[    3.847461] hub 1-0:1.0: 1 port detected
[    3.852914] hub 2-0:1.0: USB hub found
[    3.857117] hub 2-0:1.0: 4 ports detected
[    3.862870] pcie-starfive 9c0000000.pcie: host bridge /soc/pcie@9c0000000 ranges:
[    3.871178] pcie-starfive 9c0000000.pcie:      MEM 0x0038000000..0x003fffffff -> 0x0038000000
[    3.880617] pcie-starfive 9c0000000.pcie:      MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[    4.145144] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    4.315173] usb usb2-port2: over-current condition
[    4.328025] hub 1-1:1.0: USB hub found
[    4.332314] hub 1-1:1.0: 4 ports detected
[    4.475501] usb 2-3: new SuperSpeed USB device number 2 using xhci_hcd
[    4.515362] hub 2-3:1.0: USB hub found
[    4.520317] hub 2-3:1.0: 4 ports detected
[    4.850743] usb 2-3.1: new SuperSpeed USB device number 3 using xhci_hcd
[    5.125302] pcie-starfive 9c0000000.pcie: port link down
[    5.132292] pcie-starfive 9c0000000.pcie: PCI host bridge to bus 0001:00
[    5.139713] pci_bus 0001:00: root bus resource [bus 00-ff]
[    5.145774] pci_bus 0001:00: root bus resource [mem 0x38000000-0x3fffffff]
[    5.153338] pci_bus 0001:00: root bus resource [mem 0x980000000-0x9bfffffff pref]
[    5.161631] pci 0001:00:00.0: [1556:1111] type 01 class 0x060400
[    5.168331] pci 0001:00:00.0: supports D1 D2
[    5.173031] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    5.184076] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
[    5.191400] pci 0001:00:00.0: PCI bridge to [bus 01]
[    5.203000] dw_axi_dmac_platform 16050000.dma-controller: DesignWare AXI DMA Controller, 4 channels
[    5.214131] printk: console [ttyS0] disabled
[    5.239483] 10000000.serial: ttyS0 at MMIO 0x10000000 (irq = 62, base_baud = 1500000) is a 16550A
[    5.249316] printk: console [ttyS0] enabled
[    5.249316] printk: console [ttyS0] enabled
[    5.258124] printk: bootconsole [uart0] disabled
[    5.258124] printk: bootconsole [uart0] disabled
[    5.272114] jh7110-crypto 16000000.crypto: will run requests pump with realtime priority
[    5.272696] dwmmc_starfive 16020000.mmc: IDMAC supports 32-bit address mode.
[    5.282521] ssp-pl022 10060000.spi: ARM PL022 driver, device ID: 0x00041022
[    5.287392] dwmmc_starfive 16020000.mmc: Using internal DMA controller.
[    5.294344] ssp-pl022 10060000.spi: mapped registers from 0x0000000010060000 to 00000000bd07b881
[    5.300929] dwmmc_starfive 16020000.mmc: Version ID is 290a
[    5.310977] ssp-pl022 10060000.spi: will use autosuspend for runtime pm, delay 100ms
[    5.315347] dwmmc_starfive 16020000.mmc: DW MMC controller at irq 66,32 bit host data width,32 deep fifo
[    5.332621] seeed_panel 2-0045: Unknown Atmel firmware revision: 0x00
[    5.332894] tinker_ft5406 2-0038: Address = 0x38
[    5.339328] mmc_host mmc1: card is polling.
[    5.343713] tinker_ft5406 2-0038: width = 800, height = 480, reverse = 1
[    5.354866] tinker_ft5406 2-0038: i2c read error, -121
[    5.360041] tinker_ft5406 2-0038: Checking touch ic failed
[    5.365556] tinker_ft5406: probe of 2-0038 failed with error -121
[    5.371963] Goodix-TS 2-0014: supply AVDD28 not found, using dummy regulator
[    5.379199] Goodix-TS 2-0014: supply VDDIO not found, using dummy regulator
[    5.505288] Goodix-TS 2-0014: Error reading 1 bytes from 0x8140: -121
[    5.525146] usb 1-1.3: new high-speed USB device number 3 using xhci_hcd
[    5.545274] Goodix-TS 2-0014: Error reading 1 bytes from 0x8140: -121
[    5.585141] Goodix-TS 2-0014: I2C communication failure: -121
[    5.585154] mmc_host mmc1: Bus speed (slot 0) = 49500000Hz (slot req 400000Hz, actual 399193HZ div = 62)
[    5.591058] Goodix-TS: probe of 2-0014 failed with error -121
[    5.606652] starfive_jadard 2-0019: no 4lane connect!!!!
[    5.613062] axp20x-i2c 5-0036: AXP20x variant AXP15060 found
[    5.622344] axp20x-i2c 5-0036: AXP20X driver loaded
[    5.628706] imx219 6-0010: supply VANA not found, using dummy regulator
[    5.635528] imx219 6-0010: supply VDIG not found, using dummy regulator
[    5.642224] imx219 6-0010: supply VDDL not found, using dummy regulator
[    5.656449] imx219 6-0010: Error reading reg 0x   0: -121
[    5.661870] imx219 6-0010: failed to read chip id 219
[    5.667185] imx219: probe of 6-0010 failed with error -121
[    5.673044] imx708 6-001a: supply VANA1 not found, using dummy regulator
[    5.679922] imx708 6-001a: supply VANA2 not found, using dummy regulator
[    5.686729] imx708 6-001a: supply VDIG not found, using dummy regulator
[    5.693452] imx708 6-001a: supply VDDL not found, using dummy regulator
[    5.704006] hub 1-1.3:1.0: USB hub found
[    5.708260] hub 1-1.3:1.0: 4 ports detected
[    5.712627] imx708 6-001a: failed to read chip id 708, with error -5
[    5.719727] imx708: probe of 6-001a failed with error -5
[    5.725384] ov4689 6-0036: supply DOVDD not found, using dummy regulator
[    5.732233] ov4689 6-0036: supply AVDD not found, using dummy regulator
[    5.738972] ov4689 6-0036: supply DVDD not found, using dummy regulator
[    5.745949] ov4689 6-0036: ov4689_read_reg: error: reg=300a
[    5.751547] ov4689 6-0036: ov4689_check_chip_id: failed to read chip identifier
[    5.759115] ov4689: probe of 6-0036 failed with error -121
[    5.764786] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe begin
[    5.771094] sf-mipi-dphy-tx 295e0000.mipi-dphy: ===> sf_dphy_probe enter, 442 
[    5.778554] sf-mipi-dphy-tx 295e0000.mipi-dphy: control ECO
[    5.784178] sf-mipi-dphy-tx 295e0000.mipi-dphy: supply mipi_1p8 not found, using dummy regulator
[    5.793277] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe end
[    5.799744] cdns-dsi 295d0000.mipi: dsi_sys_clk = 297000000
[    5.805693] cdns-dsi 295d0000.mipi: starfive dsi bind end
[    5.814866] dwmmc_starfive 16010000.mmc: IDMAC supports 32-bit address mode.
[    5.821976] dwmmc_starfive 16010000.mmc: Using internal DMA controller.
[    5.822800] jh7110-vin 19800000.vin_sysctl: stfcamss probe enter!
[    5.828603] dwmmc_starfive 16010000.mmc: Version ID is 290a
[    5.836108] jh7110-vin 19800000.vin_sysctl: stfcamss probe success!
[    5.840281] dwmmc_starfive 16010000.mmc: DW MMC controller at irq 89,32 bit host data width,32 deep fifo
[    5.846803] of_cfs_init
[    5.856045] mmc_host mmc1: Bus speed (slot 0) = 49500000Hz (slot req 50000000Hz, actual 49500000HZ div = 0)
[    5.856228] mmc_host mmc0: card is non-removable.
[    5.858446] of_cfs_init: OK
[    5.868205] mmc1: new high speed SDHC card at address 59b4
[    5.872887] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    5.876414] mmcblk1: mmc1:59b4       29.8 GiB
[    5.895763] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    5.900116]  mmcblk1: p1 p2 p3 p4
[    5.902076] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[    5.913545] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid
[    6.095220] mmc_host mmc0: Bus speed (slot 0) = 49500000Hz (slot req 400000Hz, actual 399193HZ div = 62)
[    6.145210] usb 1-1.3.3: new low-speed USB device number 4 using xhci_hcd
[    6.322383] input: PixArt USB Optical Mouse as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3.3/1-1.3.3:1.0/0003:093A:2510.0001/input/input0
[    6.339664] hid-generic 0003:093A:2510.0001: input: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:01:00.0-1.3.3/input0
[    6.351837] clk: Disabling unused clocks
[    6.359343] starfive display-subsystem: bound 29400000.dc8200 (ops 0xffffffff810a8560)
[    6.367295] innohdmi-starfive 29590000.hdmi: inno hdmi bind begin
[    6.374086] innohdmi-starfive 29590000.hdmi: [drm:inno_hdmi_bind] registered Inno HDMI I2C bus driver success
[    6.384215] innohdmi-starfive 29590000.hdmi: HDMI&AUDIO register done.
[    6.390765] innohdmi-starfive 29590000.hdmi: inno hdmi bind end
[    6.396693] starfive display-subsystem: bound 29590000.hdmi (ops 0xffffffff810a93d0)
[    6.404436] vs-simple-encoder dsi-output: encoder_bind begin
[    6.410148] no panel, -517
[    6.412860] vs-simple-encoder dsi-output: encoder_bind error
[    6.418537] starfive display-subsystem: bound dsi-output (ops 0xffffffff810a9018)
[    6.426499] [drm] Initialized starfive 1.0.0 20191101 for display-subsystem on minor 1
[    6.475185] usb 1-1.3.4: new low-speed USB device number 5 using xhci_hcd
[    6.497263] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate rate 148500000 tmdsclk 148500000
[    6.497279] innohdmi-starfive 29590000.hdmi: inno_hdmi_phy_clk_set_rate hdmi->pre_cfg->pixclock = 148500000
[    6.600497] Console: switching to colour frame buffer device 240x67
[    6.602667] mmc_host mmc0: Bus speed (slot 0) = 49500000Hz (slot req 300000Hz, actual 298192HZ div = 83)
[    6.662197] input: SEMICO USB Keyboard as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.0/0003:1A2C:40E2.0002/input/input1
[    6.663472] starfive display-subsystem: [drm] fb0: starfivedrmfb frame buffer device
[    6.723936] ALSA device list:
[    6.726987]   #0: Starfive-PWMDAC-Sound-Card
[    6.733374] Freeing unused kernel image (initmem) memory: 2212K
[    6.739457] Run /init as init process
[    6.745693] hid-generic 0003:1A2C:40E2.0002: input: USB HID v1.10 Keyboard [SEMICO USB Keyboard] on usb-0000:01:00.0-1.3.4/input0
Loading, please wait...
[    6.770803] input: SEMICO USB Keyboard Consumer Control as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.1/0003:1A2C:40E2.0003/input/input2
Starting systemd-udevd version 252.4-1
[    6.865493] input: SEMICO USB Keyboard System Control as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.1/0003:1A2C:40E2.0003/input/input3
[    6.883769] input: SEMICO USB Keyboard as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4:1.1/0003:1A2C:40E2.0003/input/input5
[    6.901888] hid-generic 0003:1A2C:40E2.0003: input: USB HID v1.10 Keyboard [SEMICO USB Keyboard] on usb-0000:01:00.0-1.3.4/input1
[    7.075170] mmc_host mmc0: Bus speed (slot 0) = 49500000Hz (slot req 200000Hz, actual 199596HZ div = 124)
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... [-1;-1f[    7.595219] mmc_host mmc0: Bus speed (slot 0) = 49500000Hz (slot req 100000Hz, actual 99798HZ div = 248)
done.

Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.

Begin: Running /scripts/local-premount ... done.

Warning: fsck not present, so skipping root file system

[    7.870607] mmc0: Failed to initialize a non-removable card
[    8.225270] EXT4-fs (mmcblk1p4): recovery complete
[    8.238553] EXT4-fs (mmcblk1p4): mounted filesystem ed0bb0e3-07db-45e7-a1e8-e8402c7c8e1c r/w with ordered data mode. Quota mode: disabled.
done.

Begin: Running /scripts/local-bottom ... done.

Begin: Running /scripts/init-bottom ... done.

[    8.925452] systemd[1]: System time before build time, advancing clock.
[    9.028306] systemd[1]: systemd 252.4-1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    9.061144] systemd[1]: Detected architecture riscv64.


Welcome to Debian GNU/Linux bookworm/sid[    9.073711] systemd[1]: Hostname set to <saratoga-vf2>.
[0m!



[    9.748769] systemd[1]: Queued start job for default target Graphical Interface.
[    9.759977] systemd[1]: Created slice Slice /system/getty.
[    9.766645] systemd[1]: Created slice Slice /system/modprobe.
[    9.773215] systemd[1]: Created slice Slice /system/serial-getty.
[  OK  ] Created slic[    9.781945] systemd[1]: Created slice User and Session Slice.
e Slice[    9.788475] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
 /system/getty[[    9.797629] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
0m.

[  OK  ] Create[    9.809416] systemd[1]: Reached target Local Integrity Protected Volumes.
d slice Slice /system/m[    9.818442] systemd[1]: Reached target User and Group Name Lookups.
odprobe.

[[    9.826405] systemd[1]: Reached target Remote File Systems.
  OK  [0[    9.833462] systemd[1]: Reached target Slice Units.
m] Created slice[    9.839771] systemd[1]: Reached target Swaps.
 Slice [    9.845370] systemd[1]: Reached target Local Verity Protected Volumes.
/system/serial-getty.

[[0[    9.854828] systemd[1]: Listening on initctl Compatibility Named Pipe.
;32m  OK  ] Created slice User and Session Slice.

[  OK  ] Started[    9.870083] systemd[1]: Journal Audit Socket was skipped because of an unmet condition check (ConditionSecurity=audit).
 Forward Password R…u[    9.882972] systemd[1]: Listening on Journal Socket (/dev/log).
ests to Wall Dir[    9.890719] systemd[1]: Listening on Journal Socket.
ectory Watch.

[  OK[    9.897766] systemd[1]: Listening on udev Control Socket.
  ] Set up automount [0;1;3[    9.905932] systemd[1]: Listening on udev Kernel Socket.
9mArbitrary…s File System Automount Point.

[  OK  ] Reached target Local Integrity Protected Volumes.

[  OK  ] Reached target User and Group Name Lookups.

[  OK  ] Reached target Remote File Systems.

[  OK  ] Reached target Slice Units.

[  OK  ] Reached target Swaps.

[  OK  ] Reached target Local Verity Protected Volumes.

[  OK  ] Listening on initctl Compatibility Named Pipe.

[  OK  ] Listening on Journal Sock[    9.965948] systemd[1]: Mounting Huge Pages File System...
et (/dev/log).

[  OK  ] Listening on Journal Socket.

[  OK  ] Listeni[    9.981376] systemd[1]: Mounting POSIX Message Queue File System...
ng on udev Control Socket.

[[0;3[    9.991312] systemd[1]: Mounting Kernel Debug File System...
2m  OK  ] Li[    9.999177] systemd[1]: Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
stening on udev Kernel Socket.

         Mounting [   10.015902] systemd[1]: Starting Create List of Static Device Nodes...
Huge Pages File System...

       [   10.027253] systemd[1]: Starting Load Kernel Module configfs...
  Mounting POSIX Message Queue File System...

   [   10.038039] systemd[1]: Starting Load Kernel Module drm...
      Mounting Kernel Debug File System...

         Starting Create List[   10.048874] systemd[1]: Starting Load Kernel Module efi_pstore...
 of Static Device Nodes...

         Starting Load Kernel Module configfs...

         Starting Load Kernel Module drm...

         Starting [[   10.071114] systemd[1]: Starting Load Kernel Module fuse...
0;1;39mLoad Kernel Module efi_pstore...

         Starting Load Kernel Module fuse...

[   10.096057] systemd[1]: Starting Journal Service...
         Starting Journal Service...

[   10.122777] systemd[1]: Starting Load Kernel Modules...
[   10.141147] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting Load Kernel Modules...

         Starting Remount Root and Kernel File Systems...

[   10.176415] systemd[1]: Repartition Root Disk was skipped because no trigger condition checks were met.
[   10.194805] systemd[1]: Starting Coldplug All udev Devices...
[   10.213820] systemd[1]: Mounted Huge Pages File System.
         Starting Coldplug All udev Devices...

[  OK  ] Mounted Huge Pages File System.

[   10.240297] systemd[1]: Mounted POSIX Message Queue File System.
[   10.253874] systemd[1]: Mounted Kernel Debug File System.
[  OK  ] Mounted POSIX Message Queue File System.

[  OK  ] Mounted Kernel Debug File System.

[   10.274649] systemd[1]: Started Journal Service.
[  OK  ] Started Journal Service.

[  OK  ] Finished Create List of Static Device Nodes.

[  OK  ] Finished Load Kernel Module configfs.

[  OK  ] Finished Load Kernel Module drm.

[  OK  ] Finished Load Kernel Module efi_pstore.

[  OK  ] Finished Load Kernel Module fuse.

[  OK  ] Finished Load Kernel Modules.

[  OK  ] Finished Remount Root and Kernel File Systems.

         Mounting FUSE Control File System...

         Mounting Kernel Configuration File System...

         Starting Flush Journal to Persistent Storage...

[   10.435869] systemd-journald[217]: Received client request to flush runtime journal.
[   10.446175] systemd-journald[217]: File /var/log/journal/2f1736059b304274b2bd24e609e12d9b/system.journal corrupted or uncleanly shut down, renaming and replacing.
         Starting Load/Save Random Seed...

         Starting Apply Kernel Variables...

         Starting Create System Users...

[  OK  ] Mounted FUSE Control File System.

[  OK  ] Mounted Kernel Configuration File System.

[  OK  ] Finished Load/Save Random Seed.

[  OK  ] Finished Coldplug All udev Devices.

         Starting Helper to synchronize boot up for ifupdown...

[  OK  ] Finished Apply Kernel Variables.

[  OK  ] Finished Create System Users.

[  OK  ] Finished Helper to synchronize boot up for ifupdown.

         Starting Create Static Device Nodes in /dev...

[  OK  ] Finished Flush Journal to Persistent Storage.

[  OK  ] Finished Create Static Device Nodes in /dev.

[  OK  ] Reached target Preparation for Local File Systems.

[  OK  ] Set up automount EFI System Partition Automount.

[  OK  ] Reached target Local File Systems.

         Starting Raise network interfaces...

         Starting Tell Plymouth To Write Out Runtime Data...

         Starting Set Up Additional Binary Formats...

         Starting Create Volatile Files and Directories...

         Starting Rule-based Manage…for Device Events and Files...

[  OK  ] Finished Tell Plymouth To Write Out Runtime Data.

         Mounting Arbitrary Executable File Formats File System...

[  OK  ] Mounted Arbitrary Executable File Formats File System.

[  OK  ] Finished Set Up Additional Binary Formats.

[  OK  ] Finished Create Volatile Files and Directories.

         Starting Network Time Synchronization...

         Starting Record System Boot/Shutdown in UTMP...

[  OK  ] Finished Raise network interfaces.

[  OK  ] Finished Record System Boot/Shutdown in UTMP.

[  OK  ] Started Rule-based Manager for Device Events and Files.

         Starting Show Plymouth Boot Screen...

[  OK  ] Found device /dev/ttyS0.

[   12.240767] systemd-journald[217]: Oldest entry in /var/log/journal/2f1736059b304274b2bd24e609e12d9b/system.journal is older than the configured file retention duration (1month), suggesting rotation.
[  OK  ] Started Network Time Synchronization.

[   12.302518] systemd-journald[217]: /var/log/journal/2f1736059b304274b2bd24e609e12d9b/system.journal: Journal header limits reached or header out-of-date, rotating.
[  OK  ] Started Show Plymouth Boot Screen.

[  OK  ] Started Forward Password R…s to Plymouth Directory Watch.

[  OK  ] Reached target Local Encrypted Volumes.

[  OK  ] Reached target Path Units.

[  OK  ] Reached target System Initialization.

[  OK  ] Started Daily Cleanup of Temporary Directories.

[  OK  ] Reached target System Time Set.

[  OK  ] Started Daily apt download activities.

[  OK  ] Started Daily apt upgrade and clean activities.

[  OK  ] Started Daily dpkg database backup timer.

[  OK  ] Started Periodic ext4 Onli…ata Check for All Filesystems.

[  OK  ] Started Daily exim4-base housekeeping.

[  OK  ] Started Discard unused blocks once a week.

[  OK  ] Started Daily rotation of log files.

[  OK  ] Started Daily man-db regeneration.

[  OK  ] Reached target Timer Units.

[  OK  ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.

[  OK  ] Listening on D-Bus System Message Bus Socket.

[  OK  ] Reached target Socket Units.

[  OK  ] Reached target Basic System.

         Starting Accounts Service...

         Starting Avahi mDNS/DNS-SD Stack...

         Starting Bluetooth management mechanism...

[  OK  ] Started Regular background program processing daemon.

         Starting D-Bus System Message Bus...

         Starting Remove Stale Onli…t4 Metadata Check Snapshots...

         Starting Authorization Manager...

         Starting Power Profiles daemon...

         Starting Switcheroo Control Proxy service...

         Starting User Login Management...

         Starting Disk Manager...

[   13.400337] vdec: loading out-of-tree module taints kernel.
[   13.432921] cnm_jpu 13090000.jpu: init device.
[   13.446919] SUCCESS alloc_chrdev_region
[   13.456795] vdec 130a0000.vpu_dec: device init.
[   13.467064] SUCCESS alloc_chrdev_region
[  OK  ] Created slice Slice /system/systemd-fsck.

[  OK  ] Reached target Hardware activated USB gadget.

[  OK  ] Listening on fsck to fsckd communication Socket.

[  OK  ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.

         Starting File System Check on /dev/mmcblk1p3...

[  OK  ] Started File System Check Daemon to report status.

[  OK  ] Started D-Bus System Message Bus.

         Starting Network Manager...

         Starting WPA supplicant...

[  OK  ] Started Avahi mDNS/DNS-SD Stack.

[  OK  ] Started User Login Management.

[  OK  ] Started Switcheroo Control Proxy service.

[   14.549162] alsactl[339]: memfd_create() called without MFD_EXEC or MFD_NOEXEC_SEAL set
[   14.549162] alsactl[338]: memfd_create() called without MFD_EXEC or MFD_NOEXEC_SEAL set
[  OK  ] Started Authorization Manager.

[  OK  ] Started Accounts Service.

[  OK  ] Started Power Profiles daemon.

         Starting Modem Manager...

         Starting Save/Restore Sound Card State...

[  OK  ] Finished Save/Restore Sound Card State.

[  OK  ] Reached target Sound Card.

[  OK  ] Started WPA supplicant.

[  OK  ] Finished File System Check on /dev/mmcblk1p3.

         Mounting EFI System Partition Automount...

[  OK  ] Mounted EFI System Partition Automount.

[  OK  ] Started Disk Manager.

[  OK  ] Started Network Manager.

[  OK  ] Reached target Network.

         Starting Network Manager Wait Online...

         Starting OpenBSD Secure Shell server...

         Starting Permit User Sessions...

[  OK  ] Started Modem Manager.

[  OK  ] Finished Permit User Sessions.

         Starting GNOME Display Manager...

         Starting Hold until boot process finishes up...

         Starting Hostname Service...

[  OK  ] Started Hostname Service.

         Starting Network Manager Script Dispatcher Service...

[  OK  ] Started GNOME Display Manager.

[  OK  ] Started OpenBSD Secure Shell server.

[  OK  ] Started Network Manager Script Dispatcher Service.

[   16.794890] starfive-dwmac 16030000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   16.797159] starfive-dwmac 16030000.ethernet eth0: PHY [stmmac-0:00] driver [YT8531 Gigabit Ethernet] (irq=POLL)
[   16.797183] dwmac4: Master AXI performs fixed burst length
[   16.797197] starfive-dwmac 16030000.ethernet eth0: No Safety Features support found
[   16.797216] starfive-dwmac 16030000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   16.798035] starfive-dwmac 16030000.ethernet eth0: configuring for phy/rgmii-id link mode
[   16.861402] starfive-dwmac 16040000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[   16.906747] starfive-dwmac 16040000.ethernet eth1: PHY [stmmac-1:00] driver [YT8531 Gigabit Ethernet] (irq=POLL)
[   16.926182] dwmac4: Master AXI performs fixed burst length
[   16.926211] starfive-dwmac 16040000.ethernet eth1: No Safety Features support found
[   16.926235] starfive-dwmac 16040000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[   16.937729] starfive-dwmac 16040000.ethernet eth1: configuring for phy/rgmii-id link mode
[   19.918388] starfive-dwmac 16030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx


Debian GNU/Linux bookworm/sid saratoga-vf2 ttyS0

saratoga-vf2 login: [   36.395261] mipi_0p9: disabling

** read zero bytes from stdin **

Terminating...
Thanks for using picocom