vkBasalt for FSR improvement

vkBasalt.conf

#effects is a colon seperated list of effect to use
#e.g.: effects = fxaa:cas
#effects will be run in order from left to right
#one effect can be run multiple times e.g. smaa:smaa:cas
#cas    - Contrast Adaptive Sharpening
#dls    - Denoised Luma Sharpening
#fxaa   - Fast Approximate Anti-Aliasing
#smaa   - Enhanced Subpixel Morphological Antialiasing
#lut    - Color LookUp Table
effects = smaa:dls

reshadeTexturePath = "/path/to/reshade-shaders/Textures"
reshadeIncludePath = "/path/to/reshade-shaders/Shaders"
depthCapture = off

#toggleKey toggles the effects on/off
toggleKey = Home

#enableOnLaunch sets if the effects are emabled when started
enableOnLaunch = True

#casSharpness specifies the amount of sharpning in the CAS shader.
#0.0 less sharp, less artefacts, but not off
#1.0 maximum sharp more artefacts
#Everything in between is possible
#negative values sharpen even less, up to -1.0 make a visible difference
casSharpness = 0.3

#dlsSharpness specifies the amount of sharpening in the Denoised Luma Sharpening shader.
#Increase to sharpen details within the image.
#0.0 less sharp, less artefacts, but not off
#1.0 maximum sharp more artefacts
dlsSharpness = 0.5

#dlsDenoise specifies the amount of denoising in the Denoised Luma Sharpening shader.
#Increase to limit how intensely film grain within the image gets sharpened.
#0.0 min
#1.0 max
dlsDenoise = 0.8

#fxaaQualitySubpix can effect sharpness.
#1.00 - upper limit (softer)
#0.75 - default amount of filtering
#0.50 - lower limit (sharper, less sub-pixel aliasing removal)
#0.25 - almost off
#0.00 - completely off
fxaaQualitySubpix = 0.75

#fxaaQualityEdgeThreshold is the minimum amount of local contrast required to apply algorithm.
#0.333 - too little (faster)
#0.250 - low quality
#0.166 - default
#0.125 - high quality 
#0.063 - overkill (slower)
fxaaQualityEdgeThreshold = 0.1

#fxaaQualityEdgeThresholdMin trims the algorithm from processing darks.
#0.0833 - upper limit (default, the start of visible unfiltered edges)
#0.0625 - high quality (faster)
#0.0312 - visible limit (slower)
#Special notes: due to the current implementation you
#Likely want to set this to zero.
#As colors that are mostly not-green
#will appear very dark in the green channel!
#Tune by looking at mostly non-green content,
#then start at zero and increase until aliasing is a problem.
fxaaQualityEdgeThresholdMin = 0.0312

#smaaEdgeDetection changes the edge detection shader
#luma  - default
#color - might catch more edges, but is more expensive
smaaEdgeDetection = luma

#smaaThreshold specifies the threshold or sensitivity to edges
#Lowering this value you will be able to detect more edges at the expense of performance.
#Range: [0, 0.5]
#0.1 is a reasonable value, and allows to catch most visible edges.
#0.05 is a rather overkill value, that allows to catch 'em all.
smaaThreshold = 0.05

#smaaMaxSearchSteps specifies the maximum steps performed in the horizontal/vertical pattern searches
#Range: [0, 112]
#4  - low
#8  - medium
#16 - high
#32 - ultra
smaaMaxSearchSteps = 32

#smaaMaxSearchStepsDiag specifies the maximum steps performed in the diagonal pattern searches
#Range: [0, 20]
#0  - low, medium
#8  - high
#16 - ultra
smaaMaxSearchStepsDiag = 16

#smaaCornerRounding specifies how much sharp corners will be rounded
#Range: [0, 100]
#25 is a reasonable value
smaaCornerRounding = 25

#lutFile is the path to the LUT file that will be used
#supported are .CUBE files and .png with width == height * height
lutFile = "/path/to/lut"