Created
January 29, 2010 07:53
-
-
Save oraccha/289542 to your computer and use it in GitHub Desktop.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| \/ | __ _ _ ____ _____| | | | |
| |\/| |/ _` | '__\ \ / / _ \ | | | |
| | | | (_| | | \ V / __/ | | | |
|_| |_|\__,_|_| \_/ \___|_|_| | |
_ _ ____ _ | |
| | | | | __ ) ___ ___ | |_ | |
| | | |___| _ \ / _ \ / _ \| __| | |
| |_| |___| |_) | (_) | (_) | |_ | |
\___/ |____/ \___/ \___/ \__| | |
** MARVELL BOARD: SHEEVA PLUG LE | |
U-Boot 1.1.4 (Sep 7 2009 - 20:21:09) Marvell version: 3.4.16 | |
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE60 | |
Soc: 88F6281 A0 (DDR2) | |
CPU running @ 1200Mhz L2 running @ 400Mhz | |
SysClock = 400Mhz , TClock = 200Mhz | |
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 | |
DRAM CS[0] base 0x00000000 size 256MB | |
DRAM CS[1] base 0x10000000 size 256MB | |
DRAM Total size 512MB 16bit width | |
Flash: 0 kB | |
Addresses 8M - 0M are saved for the U-Boot usage. | |
Mem malloc Initialization (8M - 7M): Done | |
NAND:512 MB | |
CPU : Marvell Feroceon (Rev 1) | |
Streaming disabled | |
Write allocate disabled | |
USB 0: host mode | |
PEX 0: interface detected no Link. | |
Net: egiga0 [PRIME], egiga1 | |
Hit any key to stop autoboot: 0 | |
NAND read: device 0 offset 0x100000, size 0x400000 | |
Reading data from 0x4f5800 -- 100% complete. | |
4194304 bytes read: OK | |
## Booting image at 00800000 ... | |
Image Name: Linux-2.6.22.18 | |
Created: 2009-03-19 9:18:16 UTC | |
Image Type: ARM Linux Kernel Image (uncompressed) | |
Data Size: 2106696 Bytes = 2 MB | |
Load Address: 00008000 | |
Entry Point: 00008000 | |
Verifying Checksum ... OK | |
OK | |
Starting kernel ... | |
Uncompressing Linux............................................................. | |
....................................................................... done, bo | |
oting the kernel. | |
Linux version 2.6.22.18 (dhaval@devbox) (gcc version 4.2.1) #1 Thu Mar 19 14:46: | |
22 IST 2009 | |
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 | |
Machine: Feroceon-KW | |
Using UBoot passing parameters structure | |
Memory policy: ECC disabled, Data cache writeback | |
CPU0: D VIVT write-back cache | |
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets | |
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets | |
Built 1 zonelists. Total pages: 130048 | |
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uI | |
mage),0x1fb00000@0x500000(rootfs) rw root=/dev/mtdblock1 rw ip=10.4.50.4:10.4.50 | |
.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none | |
PID hash table entries: 2048 (order: 11, 8192 bytes) | |
Console: colour dummy device 80x30 | |
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) | |
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) | |
Memory: 256MB 256MB 0MB 0MB = 512MB total | |
Memory: 515456KB available (3864K code, 257K data, 104K init) | |
Mount-cache hash table entries: 512 | |
CPU: Testing write buffer coherency: ok | |
NET: Registered protocol family 16 | |
CPU Interface | |
------------- | |
SDRAM_CS0 ....base 00000000, size 256MB | |
SDRAM_CS1 ....base 10000000, size 256MB | |
SDRAM_CS2 ....disable | |
SDRAM_CS3 ....disable | |
PEX0_MEM ....base e8000000, size 128MB | |
PEX0_IO ....base f2000000, size 1MB | |
INTER_REGS ....base f1000000, size 1MB | |
NFLASH_CS ....base fa000000, size 2MB | |
SPI_CS ....base f4000000, size 16MB | |
BOOT_ROM_CS ....no such | |
DEV_BOOTCS ....no such | |
CRYPT_ENG ....base f0000000, size 2MB | |
Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- SHEEVA PLUG Soc | |
: 88F6281 A0 LE | |
Detected Tclk 200000000 and SysClk 400000000 | |
MV Buttons Device Load | |
Marvell USB EHCI Host controller #0: c08b8600 | |
PEX0 interface detected no Link. | |
PCI: bus0: Fast back to back transfers enabled | |
SCSI subsystem initialized | |
usbcore: registered new interface driver usbfs | |
usbcore: registered new interface driver hub | |
usbcore: registered new device driver usb | |
NET: Registered protocol family 2 | |
Time: kw_clocksource clocksource has been installed. | |
IP route cache hash table entries: 16384 (order: 4, 65536 bytes) | |
TCP established hash table entries: 65536 (order: 7, 524288 bytes)TCP bind hash table entries: 65536 (order: 6, 262144 bytes) | |
TCP: Hash tables configured (established 65536 bind 65536) | |
TCP reno registered | |
RTC registered | |
Use the XOR engines (acceleration) for enhancing the following functions: | |
o RAID 5 Xor calculation | |
o kernel memcpy | |
o kenrel memzero | |
Number of XOR engines to use: 4 | |
cesadev_init(c000c894) | |
mvCesaInit: sessions=640, queue=64, pSram=f0000000 | |
Warning: TS unit is powered off. | |
MV Buttons Driver Load | |
NTFS driver 2.1.28 [Flags: R/O]. | |
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. | |
io scheduler noop registered | |
io scheduler anticipatory registered (default) | |
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled | |
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A | |
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A | |
Loading Marvell Ethernet Driver: | |
o Cached descriptors in DRAM | |
o DRAM SW cache-coherency | |
o Single RX Queue support - ETH_DEF_RXQ=0 | |
o Single TX Queue support - ETH_DEF_TXQ=0 | |
o TCP segmentation offload enabled | |
o Receive checksum offload enabled | |
o Transmit checksum offload enabled | |
o Network Fast Processing (Routing) supported | |
o Driver ERROR statistics enabled | |
o Driver INFO statistics enabled | |
o Proc tool API enabled | |
o Rx descripors: q0=128 | |
o Tx descripors: q0=532 | |
o Loading network interface(s): | |
o eth0, ifindex = 1, GbE port = 0 | |
o eth1, ifindex = 2, GbE port = 1 | |
mvFpRuleDb (dfd00000): 16384 entries, 65536 bytes | |
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI | |
Copyright (c) 1999-2006 Intel Corporation. | |
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI | |
e100: Copyright(c) 1999-2006 Intel Corporation | |
Integrated Sata device found | |
scsi0 : Marvell SCSI to SATA adapter | |
scsi1 : Marvell SCSI to SATA adapter | |
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ | |
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) | |
Scanning device for bad blocks | |
2 cmdlinepart partitions found on MTD device nand_mtd | |
Using command line partition definition | |
Creating 2 MTD partitions on "nand_mtd": | |
0x00100000-0x00500000 : "uImage" | |
0x00500000-0x20000000 : "rootfs" | |
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI | |
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 | |
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 | |
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 | |
usb usb1: configuration #1 chosen from 1 choice | |
hub 1-0:1.0: USB hub found | |
hub 1-0:1.0: 1 port detected | |
USB Universal Host Controller Interface driver v3.0 | |
usbcore: registered new interface driver usblp | |
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver | |
Initializing USB Mass Storage driver... | |
usbcore: registered new interface driver usb-storage | |
USB Mass Storage support registered. | |
mice: PS/2 mouse device common for all mice | |
i2c /dev entries driver | |
Linux telephony interface: v1.00 | |
Marvell Telephony Driver: | |
mvBoardVoiceAssembleModeGet: TDM not supported(boardId=0x9) | |
assembly=-1,irq=-1 | |
mp_check_config: Error, invalid voice assembley mode | |
md: linear personality registered for level -1 | |
md: raid0 personality registered for level 0 | |
md: raid1 personality registered for level 1 | |
raid6: int32x1 97 MB/s | |
raid6: int32x2 114 MB/s | |
raid6: int32x4 122 MB/s | |
raid6: int32x8 110 MB/s | |
raid6: using algorithm int32x4 (122 MB/s) | |
md: raid6 personality registered for level 6 | |
md: raid5 personality registered for level 5 | |
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 | |
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 | |
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 | |
usb usb1: configuration #1 chosen from 1 choice | |
hub 1-0:1.0: USB hub found | |
hub 1-0:1.0: 1 port detected | |
USB Universal Host Controller Interface driver v3.0 | |
usbcore: registered new interface driver usblp | |
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver | |
Initializing USB Mass Storage driver... | |
usbcore: registered new interface driver usb-storage | |
USB Mass Storage support registered. | |
mice: PS/2 mouse device common for all mice | |
i2c /dev entries driver | |
Linux telephony interface: v1.00 | |
Marvell Telephony Driver: | |
mvBoardVoiceAssembleModeGet: TDM not supported(boardId=0x9) | |
assembly=-1,irq=-1 | |
mp_check_config: Error, invalid voice assembley mode | |
md: linear personality registered for level -1 | |
md: raid0 personality registered for level 0 | |
md: raid1 personality registered for level 1 | |
raid6: int32x1 97 MB/s | |
raid6: int32x2 114 MB/s | |
raid6: int32x4 122 MB/s | |
raid6: int32x8 110 MB/s | |
raid6: using algorithm int32x4 (122 MB/s) | |
md: raid6 personality registered for level 6 | |
md: raid5 personality registered for level 5 | |
md: raid4 personality registered for level 4 | |
raid5: measuring checksumming speed | |
arm4regs : 1084.000 MB/sec | |
8regs : 754.800 MB/sec | |
32regs : 899.600 MB/sec | |
raid5: using function: arm4regs (1084.000 MB/sec) | |
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com | |
dm_crypt using the OCF package. | |
sdhci: Secure Digital Host Controller Interface driver | |
sdhci: Copyright(c) Pierre Ossman | |
mvsdmmc: irq =28 start f1090000 | |
mvsdmmc: no IRQ detect | |
usbcore: registered new interface driver usbhid | |
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver | |
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC). | |
mvCLAudioCodecRegGet: Error while reading register! | |
mvCLAudioCodecInit: Error - Invalid Cirrus Logic chip/rev ID! | |
Error - Cannot initialize audio decoder.at address =0xff<6>ALSA device list: | |
#0: Marvell mv88fx_snd ALSA driver | |
TCP cubic registered | |
NET: Registered protocol family 1 | |
NET: Registered protocol family 17 | |
eth0: link down | |
eth0: started | |
IP-Config: Complete: | |
device=eth0, addr=10.4.50.4, mask=255.255.255.0, gw=10.4.50.5, | |
host=DB88FXX81, domain=, nis-domain=(none), | |
bootserver=10.4.50.5, rootserver=10.4.50.5, rootpath= | |
md: Autodetecting RAID arrays. | |
md: autorun ... | |
md: ... autorun DONE. | |
eth0: link up, full duplex, speed 1 Gbps | |
Empty flash at 0x087dd338 ends at 0x087dd800 | |
Empty flash at 0x0b24221c ends at 0x0b242800 | |
Empty flash at 0x178038bc ends at 0x17804000 | |
VFS: Mounted root (jffs2 filesystem). | |
Freeing init memory: 104K | |
* Setting preliminary keymap... [ OK ] | |
* Setting the system clock | |
* Starting basic networking... [ OK ] | |
* Starting kernel event manager... [ OK ] | |
* Loading hardware drivers... [ OK ] | |
* Setting the system clock | |
* Loading kernel modules... | |
* Loading manual drivers... [ OK ] | |
* Setting kernel variables (/etc/sysctl.conf)... [ OK ] | |
* Setting kernel variables (/etc/sysctl.d/10-console-messages.conf)... [ OK ] | |
* Setting kernel variables (/etc/sysctl.d/10-network-security.conf)... [ OK ] | |
* Setting kernel variables (/etc/sysctl.d/10-process-security.conf)... error: "vm.mmap_min_addr" is an unknown key | |
[fail] | |
* Setting kernel variables (/etc/sysctl.d/10-tcp-timestamps-workaround.conf)... [ OK ] | |
* Activating swap... [ OK ] | |
FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory | |
FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory | |
* Starting early crypto disks... [ OK ] | |
FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory | |
FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory | |
* Starting remaining crypto disks... [ OK ] | |
* Checking file systems... fsck 1.41.3 (12-Oct-2008) | |
[ OK ] | |
* Mounting local filesystems... [ OK ] | |
* Activating swapfile swap... [ OK ] | |
* Configuring network interfaces... [ OK ] | |
* Setting up console font and keymap... [ OK ] | |
* Starting system log daemon... | |
* Starting kernel log daemon... [ OK ] | |
* Starting OpenBSD Secure Shell server sshd [ OK ] | |
* Starting periodic command scheduler crond [ OK ] | |
fat: exports duplicate symbol fat_add_entries (owned by kernel) | |
insmod: error inserting '/boot/fat.ko': -1 Invalid module format | |
Ubuntu jaunty (development branch) debian ttyS0 | |
debian login: root | |
Password: | |
Last login: Thu Feb 17 01:07:34 UTC 2000 on ttyS0 | |
Linux debian 2.6.22.18 #1 Thu Mar 19 14:46:22 IST 2009 armv5tejl | |
The programs included with the Ubuntu system are free software; | |
the exact distribution terms for each program are described in the | |
individual files in /usr/share/doc/*/copyright. | |
Ubuntu comes with ABSOLUTELY NO WARRANTY, to the extent permitted by | |
applicable law. | |
To access official Ubuntu documentation, please visit: | |
http://help.ubuntu.com/ | |
root@debian:~# |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment