Most of programs will not accept an email using just @localhost as domain.
So, edit /etc/hosts file to make the domain localhost.com point to your machine, including this content to the file:
127.0.0.1 localhost.com
Paul paul1522
😷
raelgc
/ Email Server (Linux, Unix, Mac).md
Last active
July 20, 2024 22:07
Setup a Local Only SMTP Email Server (Linux, Unix, Mac)
Jooshboy
/ battery_info.sh
Created
January 7, 2016 18:15
Gets battery status information from an AXP209 PMU via I2C
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| #!/bin/sh | |
| # This program gets the battery info from PMU | |
| # Voltage and current charging/discharging | |
| # | |
| # Nota : temperature can be more than real because of self heating | |
| ####################################################################### | |
| # Copyright (c) 2014 by RzBo, Bellesserre, France | |
| # | |
| # Permission is granted to use the source code within this | |
| # file in whole or in part for any use, personal or commercial, |
Jooshboy
/ power_status.sh
Created
January 7, 2016 18:16
Returns AC connection status from an AXP209 PMU via I2C
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| #!/bin/sh | |
| # This program gets the power status (AC IN or BAT) | |
| # I2C interface with AXP209 | |
| # | |
| ####################################################################### | |
| # Copyright (c) 2014 by RzBo, Bellesserre, France | |
| # | |
| # Permission is granted to use the source code within this | |
| # file in whole or in part for any use, personal or commercial, | |
| # without restriction or limitation. |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Found in this post: https://www.reddit.com/r/PrintrBot/comments/3jm8bc/start_gcode_does_not_extrudeandmove_but_the_code/ | |
| Use this to reset, center, and auto-extrudea small bit before printing. | |
| G90 ; Explicitly force absolute positioning in case it was not reset previously. | |
| G28 ; Home all axes. | |
| G29 ; Auto-level the bed. | |
| G0 X0 Y0 Z0.15 F9000 ; Move to the front-left part of the bed. | |
| M109 S{print_temperature} ; Set and wait for extruder temperature. | |
| G92 E0 ; Zero the extruder. |
noygal
/ Windows Subsystem for Linux version 1 and 2 (WSL) - node install guide.md
Last active
February 21, 2024 23:17
Installing node via windows subsystem for linux
UPDATE (Fall 2020): This gist is an updated version to the Windows 10 Fall Creators Update - Installing Node.js on Windows Subsystem for Linux (WSL) guide, I usually just keep here notes, configuration or short guides for personal use, it was nice to know it also helps other ppl, I hope this one too.
Windows updated windows subsystem for linux to version 2, as the F.A.Q stated you can still use WSL version 1 side by side with version 2. I'm not sure about existing WSL machines surviving the upgrade process, but as always backup and 🤞. NOTE: WSL version 1 is not replace/deprecated, and there ar
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| //@version=3 | |
| study("BarTzar", overlay=true) | |
| //Variables to get percentage open/close | |
| breadth = high - low //this is the bar range | |
| closeBreadth = close - low // this is the closing | |
| barCloseBreadth = closeBreadth / breadth | |
| //supDayThresh = input(40, minval=0, maxval=100, title="Threshold for support") |
This is a very basic TinyMCE component. It uses 'entangle'. This allows you to link a Livewire and Alpine property to eachother. If one value changes, the other does too.
Add tinymce.blade.php to views/components/input. This can be another
component folder too if you prefer, but keep in mind that you should also
luzhuomi
/ pocketchip_debian10.md
Last active
July 12, 2024 15:04
A tutorial to upgrade NXT pocket C.H.I.P to Debian Buster
The purpose of this tutorial is to walk through the required steps to upgrade NXT chip (or pocketchip) from debian jessie to debian buster.
If you would like to start your Chip from scratch, follow the steps in the Preparation section.
A linux host machine, recommended Ubuntu 18.04. However I managed to do it with 20.10 with some tweak.