pauloromeira/tlp

## tlp
# ------------------------------------------------------------------------------
# tlp - Parameters for power saving
# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html

# dir: /etc/default/tlp

# Hint: some features are disabled by default, remove the leading # to enable
# them.

# Set to 0 to disable, 1 to enable TLP.
TLP_ENABLE=1

# Operation mode when no power supply can be detected: AC, BAT
# Concerns some desktop and embedded hardware only.
TLP_DEFAULT_MODE=AC

# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE
# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC
TLP_PERSISTENT_DEFAULT=0

# Seconds laptop mode has to wait after the disk goes idle before doing a sync.
# Non-zero value enables, zero disables laptop mode.
DISK_IDLE_SECS_ON_AC=0
DISK_IDLE_SECS_ON_BAT=2

# Dirty page values (timeouts in secs).
MAX_LOST_WORK_SECS_ON_AC=15
MAX_LOST_WORK_SECS_ON_BAT=60

# Hint: CPU parameters below are disabled by default, remove the leading #
# to enable them, otherwise kernel default values are used.

# Select a CPU frequency scaling governor.
# Intel Core i processor with intel_pstate driver:
#   powersave(*), performance
# Older hardware with acpi-cpufreq driver:
#   ondemand(*), powersave, performance, conservative, schedutil
# (*) is recommended.
# Hint: use tlp-stat -p to show the active driver and available governors.
# Important:
#   You *must* disable your distribution's governor settings or conflicts will
#   occur. ondemand is sufficient for *almost all* workloads, you should know
#   what you're doing!
#CPU_SCALING_GOVERNOR_ON_AC=powersave
#CPU_SCALING_GOVERNOR_ON_BAT=powersave

# Set the min/max frequency available for the scaling governor.
# Possible values strongly depend on your CPU. For available frequencies see
# the output of tlp-stat -p.
#CPU_SCALING_MIN_FREQ_ON_AC=0
#CPU_SCALING_MAX_FREQ_ON_AC=0
#CPU_SCALING_MIN_FREQ_ON_BAT=0
#CPU_SCALING_MAX_FREQ_ON_BAT=0

# Set energy performance hints (HWP) for Intel P-state governor:
#   default, performance, balance_performance, balance_power, power
# Values are given in order of increasing power saving.
# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required.
CPU_HWP_ON_AC=balance_performance
CPU_HWP_ON_BAT=balance_power

# Set Intel P-state performance: 0..100 (%)
# Limit the max/min P-state to control the power dissipation of the CPU.
# Values are stated as a percentage of the available performance.
# Requires an Intel Core i processor with intel_pstate driver.
#CPU_MIN_PERF_ON_AC=0
#CPU_MAX_PERF_ON_AC=100
#CPU_MIN_PERF_ON_BAT=0
#CPU_MAX_PERF_ON_BAT=30

# Set the CPU "turbo boost" feature: 0=disable, 1=allow
# Requires an Intel Core i processor.
# Important:
# - This may conflict with your distribution's governor settings
# - A value of 1 does *not* activate boosting, it just allows it
#CPU_BOOST_ON_AC=1
#CPU_BOOST_ON_BAT=0

# Minimize number of used CPU cores/hyper-threads under light load conditions
SCHED_POWERSAVE_ON_AC=0
SCHED_POWERSAVE_ON_BAT=1

# Kernel NMI Watchdog:
#   0=disable (default, saves power), 1=enable (for kernel debugging only)
NMI_WATCHDOG=0

# Change CPU voltages aka "undervolting" - Kernel with PHC patch required
# Frequency voltage pairs are written to:
#   /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
# CAUTION: only use this, if you thoroughly understand what you are doing!
#PHC_CONTROLS="F:V F:V F:V F:V"

# Set CPU performance versus energy savings policy:
#   performance, normal, powersave
# Requires kernel module msr and x86_energy_perf_policy from linux-tools
ENERGY_PERF_POLICY_ON_AC=performance
ENERGY_PERF_POLICY_ON_BAT=powersave

# Hard disk devices; separate multiple devices with spaces (default: sda).
# Devices can be specified by disk ID also (lookup with: tlp diskid).
DISK_DEVICES="sda sdb"

# Hard disk advanced power management level: 1..254, 255 (max saving, min, off)
# Levels 1..127 may spin down the disk; 255 allowable on most drives.
# Separate values for multiple disks with spaces. Use the special value 'keep'
# to keep the hardware default for the particular disk.
DISK_APM_LEVEL_ON_AC="254 254"
DISK_APM_LEVEL_ON_BAT="128 128"

# Hard disk spin down timeout:
#   0:        spin down disabled
#   1..240:   timeouts from 5s to 20min (in units of 5s)
#   241..251: timeouts from 30min to 5.5 hours (in units of 30min)
# See 'man hdparm' for details.
# Separate values for multiple disks with spaces. Use the special value 'keep'
# to keep the hardware default for the particular disk.
#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"

# Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq);
# Separate values for multiple disks with spaces. Use the special value 'keep'
# to keep the kernel default scheduler for the particular disk.
#DISK_IOSCHED="cfq cfq"

# SATA aggressive link power management (ALPM):
#   min_power, medium_power, max_performance
SATA_LINKPWR_ON_AC=max_performance
SATA_LINKPWR_ON_BAT=min_power

# Exclude SATA host devices from link power management.
# Separate multiple hosts with spaces.
#SATA_LINKPWR_BLACKLIST="host1"

# Runtime Power Management for AHCI controllers and disks:
#   on=disable, auto=enable
# EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss
#AHCI_RUNTIME_PM_ON_AC=on
#AHCI_RUNTIME_PM_ON_BAT=on

# Seconds of inactivity before disk is suspended
AHCI_RUNTIME_PM_TIMEOUT=15

# PCI Express Active State Power Management (PCIe ASPM):
#   default, performance, powersave
PCIE_ASPM_ON_AC=performance
PCIE_ASPM_ON_BAT=powersave

# Radeon graphics clock speed (profile method): low, mid, high, auto, default;
# auto = mid on BAT, high on AC; default = use hardware defaults.
# (Kernel >= 2.6.35 only, open-source radeon driver explicitly)
RADEON_POWER_PROFILE_ON_AC=high
RADEON_POWER_PROFILE_ON_BAT=low

# Radeon dynamic power management method (DPM): battery, performance
# (Kernel >= 3.11 only, requires boot option radeon.dpm=1)
RADEON_DPM_STATE_ON_AC=performance
RADEON_DPM_STATE_ON_BAT=battery

# Radeon DPM performance level: auto, low, high; auto is recommended.
RADEON_DPM_PERF_LEVEL_ON_AC=auto
RADEON_DPM_PERF_LEVEL_ON_BAT=auto

# WiFi power saving mode: on=enable, off=disable; not supported by all adapters.
WIFI_PWR_ON_AC=off
WIFI_PWR_ON_BAT=on

# Disable wake on LAN: Y/N
WOL_DISABLE=Y

# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
# A value of 0 disables, >=1 enables power saving.
SOUND_POWER_SAVE_ON_AC=0
SOUND_POWER_SAVE_ON_BAT=1

# Disable controller too (HDA only): Y/N
SOUND_POWER_SAVE_CONTROLLER=Y

# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.
# Drive can be powered on again by releasing (and reinserting) the eject lever
# or by pressing the disc eject button on newer models.
# Note: an UltraBay/MediaBay hard disk is never powered off.
BAY_POWEROFF_ON_AC=0
BAY_POWEROFF_ON_BAT=0
# Optical drive device to power off (default sr0).
BAY_DEVICE="sr0"

# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable
RUNTIME_PM_ON_AC=on
RUNTIME_PM_ON_BAT=auto

# Exclude PCI(e) device adresses the following list from Runtime PM
# (separate with spaces). Use lspci to get the adresses (1st column).
#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"

# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM.
# Default when unconfigured is "amdgpu nouveau nvidia radeon" which
# prevents accidential power-on of dGPU in hybrid graphics setups.
# Use "" to disable the feature completely.
# Separate multiple drivers with spaces.
#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon"

# Set to 0 to disable, 1 to enable USB autosuspend feature.
USB_AUTOSUSPEND=1

# Exclude listed devices from USB autosuspend (separate with spaces).
# Use lsusb to get the ids.
# Note: input devices (usbhid) are excluded automatically
#USB_BLACKLIST="1111:2222 3333:4444"

# Bluetooth devices are excluded from USB autosuspend:
#   0=do not exclude, 1=exclude
USB_BLACKLIST_BTUSB=0

# Phone devices are excluded from USB autosuspend:
#   0=do not exclude, 1=exclude (enable charging)
USB_BLACKLIST_PHONE=0

# WWAN devices are excluded from USB autosuspend:
#   0=do not exclude, 1=exclude
USB_BLACKLIST_WWAN=1

# Include listed devices into USB autosuspend even if already excluded
# by the blacklists above (separate with spaces).
# Use lsusb to get the ids.
#USB_WHITELIST="1111:2222 3333:4444"

# Set to 1 to disable autosuspend before shutdown, 0 to do nothing
# (workaround for USB devices that cause shutdown problems).
#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1

# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
# on system startup: 0=disable, 1=enable.
# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
#   are ignored when this is enabled!
RESTORE_DEVICE_STATE_ON_STARTUP=0

# Radio devices to disable on startup: bluetooth, wifi, wwan.
# Separate multiple devices with spaces.
#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan"

# Radio devices to enable on startup: bluetooth, wifi, wwan.
# Separate multiple devices with spaces.
#DEVICES_TO_ENABLE_ON_STARTUP="wifi"

# Radio devices to disable on shutdown: bluetooth, wifi, wwan
# (workaround for devices that are blocking shutdown).
#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"

# Radio devices to enable on shutdown: bluetooth, wifi, wwan
# (to prevent other operating systems from missing radios).
#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"

# Radio devices to enable on AC: bluetooth, wifi, wwan
#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"

# Radio devices to disable on battery: bluetooth, wifi, wwan
#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan"

# Radio devices to disable on battery when not in use (not connected):
# bluetooth, wifi, wwan
#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"

# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
# required). Charging starts when the remaining capacity falls below the
# START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value.
# Main / Internal battery (values in %)
START_CHARGE_THRESH_BAT0=75
STOP_CHARGE_THRESH_BAT0=85
# Ultrabay / Slice / Replaceable battery (values in %)
#START_CHARGE_THRESH_BAT1=75
#STOP_CHARGE_THRESH_BAT1=80

# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable
#RESTORE_THRESHOLDS_ON_BAT=1

# ------------------------------------------------------------------------------
# tlp-rdw - Parameters for the radio device wizard
# Possible devices: bluetooth, wifi, wwan

# Hints:
# - Parameters are disabled by default, remove the leading # to enable them.
# - Separate multiple radio devices with spaces.

# Radio devices to disable on connect.
DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"

# Radio devices to enable on disconnect.
DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""

# Radio devices to enable/disable when docked.
#DEVICES_TO_ENABLE_ON_DOCK=""
#DEVICES_TO_DISABLE_ON_DOCK=""

# Radio devices to enable/disable when undocked.
#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
#DEVICES_TO_DISABLE_ON_UNDOCK=""
	# ------------------------------------------------------------------------------
	# tlp - Parameters for power saving
	# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html

	# dir: /etc/default/tlp

	# Hint: some features are disabled by default, remove the leading # to enable
	# them.

	# Set to 0 to disable, 1 to enable TLP.
	TLP_ENABLE=1

	# Operation mode when no power supply can be detected: AC, BAT
	# Concerns some desktop and embedded hardware only.
	TLP_DEFAULT_MODE=AC

	# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE
	# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC
	TLP_PERSISTENT_DEFAULT=0

	# Seconds laptop mode has to wait after the disk goes idle before doing a sync.
	# Non-zero value enables, zero disables laptop mode.
	DISK_IDLE_SECS_ON_AC=0
	DISK_IDLE_SECS_ON_BAT=2

	# Dirty page values (timeouts in secs).
	MAX_LOST_WORK_SECS_ON_AC=15
	MAX_LOST_WORK_SECS_ON_BAT=60

	# Hint: CPU parameters below are disabled by default, remove the leading #
	# to enable them, otherwise kernel default values are used.

	# Select a CPU frequency scaling governor.
	# Intel Core i processor with intel_pstate driver:
	# powersave(*), performance
	# Older hardware with acpi-cpufreq driver:
	# ondemand(*), powersave, performance, conservative, schedutil
	# (*) is recommended.
	# Hint: use tlp-stat -p to show the active driver and available governors.
	# Important:
	# You must disable your distribution's governor settings or conflicts will
	# occur. ondemand is sufficient for almost all workloads, you should know
	# what you're doing!
	#CPU_SCALING_GOVERNOR_ON_AC=powersave
	#CPU_SCALING_GOVERNOR_ON_BAT=powersave

	# Set the min/max frequency available for the scaling governor.
	# Possible values strongly depend on your CPU. For available frequencies see
	# the output of tlp-stat -p.
	#CPU_SCALING_MIN_FREQ_ON_AC=0
	#CPU_SCALING_MAX_FREQ_ON_AC=0
	#CPU_SCALING_MIN_FREQ_ON_BAT=0
	#CPU_SCALING_MAX_FREQ_ON_BAT=0

	# Set energy performance hints (HWP) for Intel P-state governor:
	# default, performance, balance_performance, balance_power, power
	# Values are given in order of increasing power saving.
	# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required.
	CPU_HWP_ON_AC=balance_performance
	CPU_HWP_ON_BAT=balance_power

	# Set Intel P-state performance: 0..100 (%)
	# Limit the max/min P-state to control the power dissipation of the CPU.
	# Values are stated as a percentage of the available performance.
	# Requires an Intel Core i processor with intel_pstate driver.
	#CPU_MIN_PERF_ON_AC=0
	#CPU_MAX_PERF_ON_AC=100
	#CPU_MIN_PERF_ON_BAT=0
	#CPU_MAX_PERF_ON_BAT=30

	# Set the CPU "turbo boost" feature: 0=disable, 1=allow
	# Requires an Intel Core i processor.
	# Important:
	# - This may conflict with your distribution's governor settings
	# - A value of 1 does not activate boosting, it just allows it
	#CPU_BOOST_ON_AC=1
	#CPU_BOOST_ON_BAT=0

	# Minimize number of used CPU cores/hyper-threads under light load conditions
	SCHED_POWERSAVE_ON_AC=0
	SCHED_POWERSAVE_ON_BAT=1

	# Kernel NMI Watchdog:
	# 0=disable (default, saves power), 1=enable (for kernel debugging only)
	NMI_WATCHDOG=0

	# Change CPU voltages aka "undervolting" - Kernel with PHC patch required
	# Frequency voltage pairs are written to:
	# /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
	# CAUTION: only use this, if you thoroughly understand what you are doing!
	#PHC_CONTROLS="F:V F:V F:V F:V"

	# Set CPU performance versus energy savings policy:
	# performance, normal, powersave
	# Requires kernel module msr and x86_energy_perf_policy from linux-tools
	ENERGY_PERF_POLICY_ON_AC=performance
	ENERGY_PERF_POLICY_ON_BAT=powersave

	# Hard disk devices; separate multiple devices with spaces (default: sda).
	# Devices can be specified by disk ID also (lookup with: tlp diskid).
	DISK_DEVICES="sda sdb"

	# Hard disk advanced power management level: 1..254, 255 (max saving, min, off)
	# Levels 1..127 may spin down the disk; 255 allowable on most drives.
	# Separate values for multiple disks with spaces. Use the special value 'keep'
	# to keep the hardware default for the particular disk.
	DISK_APM_LEVEL_ON_AC="254 254"
	DISK_APM_LEVEL_ON_BAT="128 128"

	# Hard disk spin down timeout:
	# 0: spin down disabled
	# 1..240: timeouts from 5s to 20min (in units of 5s)
	# 241..251: timeouts from 30min to 5.5 hours (in units of 30min)
	# See 'man hdparm' for details.
	# Separate values for multiple disks with spaces. Use the special value 'keep'
	# to keep the hardware default for the particular disk.
	#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
	#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"

	# Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq);
	# Separate values for multiple disks with spaces. Use the special value 'keep'
	# to keep the kernel default scheduler for the particular disk.
	#DISK_IOSCHED="cfq cfq"

	# SATA aggressive link power management (ALPM):
	# min_power, medium_power, max_performance
	SATA_LINKPWR_ON_AC=max_performance
	SATA_LINKPWR_ON_BAT=min_power

	# Exclude SATA host devices from link power management.
	# Separate multiple hosts with spaces.
	#SATA_LINKPWR_BLACKLIST="host1"

	# Runtime Power Management for AHCI controllers and disks:
	# on=disable, auto=enable
	# EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss
	#AHCI_RUNTIME_PM_ON_AC=on
	#AHCI_RUNTIME_PM_ON_BAT=on

	# Seconds of inactivity before disk is suspended
	AHCI_RUNTIME_PM_TIMEOUT=15

	# PCI Express Active State Power Management (PCIe ASPM):
	# default, performance, powersave
	PCIE_ASPM_ON_AC=performance
	PCIE_ASPM_ON_BAT=powersave

	# Radeon graphics clock speed (profile method): low, mid, high, auto, default;
	# auto = mid on BAT, high on AC; default = use hardware defaults.
	# (Kernel >= 2.6.35 only, open-source radeon driver explicitly)
	RADEON_POWER_PROFILE_ON_AC=high
	RADEON_POWER_PROFILE_ON_BAT=low

	# Radeon dynamic power management method (DPM): battery, performance
	# (Kernel >= 3.11 only, requires boot option radeon.dpm=1)
	RADEON_DPM_STATE_ON_AC=performance
	RADEON_DPM_STATE_ON_BAT=battery

	# Radeon DPM performance level: auto, low, high; auto is recommended.
	RADEON_DPM_PERF_LEVEL_ON_AC=auto
	RADEON_DPM_PERF_LEVEL_ON_BAT=auto

	# WiFi power saving mode: on=enable, off=disable; not supported by all adapters.
	WIFI_PWR_ON_AC=off
	WIFI_PWR_ON_BAT=on

	# Disable wake on LAN: Y/N
	WOL_DISABLE=Y

	# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
	# A value of 0 disables, >=1 enables power saving.
	SOUND_POWER_SAVE_ON_AC=0
	SOUND_POWER_SAVE_ON_BAT=1

	# Disable controller too (HDA only): Y/N
	SOUND_POWER_SAVE_CONTROLLER=Y

	# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.
	# Drive can be powered on again by releasing (and reinserting) the eject lever
	# or by pressing the disc eject button on newer models.
	# Note: an UltraBay/MediaBay hard disk is never powered off.
	BAY_POWEROFF_ON_AC=0
	BAY_POWEROFF_ON_BAT=0
	# Optical drive device to power off (default sr0).
	BAY_DEVICE="sr0"

	# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable
	RUNTIME_PM_ON_AC=on
	RUNTIME_PM_ON_BAT=auto

	# Exclude PCI(e) device adresses the following list from Runtime PM
	# (separate with spaces). Use lspci to get the adresses (1st column).
	#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"

	# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM.
	# Default when unconfigured is "amdgpu nouveau nvidia radeon" which
	# prevents accidential power-on of dGPU in hybrid graphics setups.
	# Use "" to disable the feature completely.
	# Separate multiple drivers with spaces.
	#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon"

	# Set to 0 to disable, 1 to enable USB autosuspend feature.
	USB_AUTOSUSPEND=1

	# Exclude listed devices from USB autosuspend (separate with spaces).
	# Use lsusb to get the ids.
	# Note: input devices (usbhid) are excluded automatically
	#USB_BLACKLIST="1111:2222 3333:4444"

	# Bluetooth devices are excluded from USB autosuspend:
	# 0=do not exclude, 1=exclude
	USB_BLACKLIST_BTUSB=0

	# Phone devices are excluded from USB autosuspend:
	# 0=do not exclude, 1=exclude (enable charging)
	USB_BLACKLIST_PHONE=0

	# WWAN devices are excluded from USB autosuspend:
	# 0=do not exclude, 1=exclude
	USB_BLACKLIST_WWAN=1

	# Include listed devices into USB autosuspend even if already excluded
	# by the blacklists above (separate with spaces).
	# Use lsusb to get the ids.
	#USB_WHITELIST="1111:2222 3333:4444"

	# Set to 1 to disable autosuspend before shutdown, 0 to do nothing
	# (workaround for USB devices that cause shutdown problems).
	#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1

	# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
	# on system startup: 0=disable, 1=enable.
	# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
	# are ignored when this is enabled!
	RESTORE_DEVICE_STATE_ON_STARTUP=0

	# Radio devices to disable on startup: bluetooth, wifi, wwan.
	# Separate multiple devices with spaces.
	#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan"

	# Radio devices to enable on startup: bluetooth, wifi, wwan.
	# Separate multiple devices with spaces.
	#DEVICES_TO_ENABLE_ON_STARTUP="wifi"

	# Radio devices to disable on shutdown: bluetooth, wifi, wwan
	# (workaround for devices that are blocking shutdown).
	#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"

	# Radio devices to enable on shutdown: bluetooth, wifi, wwan
	# (to prevent other operating systems from missing radios).
	#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"

	# Radio devices to enable on AC: bluetooth, wifi, wwan
	#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"

	# Radio devices to disable on battery: bluetooth, wifi, wwan
	#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan"

	# Radio devices to disable on battery when not in use (not connected):
	# bluetooth, wifi, wwan
	#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"

	# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
	# required). Charging starts when the remaining capacity falls below the
	# START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value.
	# Main / Internal battery (values in %)
	START_CHARGE_THRESH_BAT0=75
	STOP_CHARGE_THRESH_BAT0=85
	# Ultrabay / Slice / Replaceable battery (values in %)
	#START_CHARGE_THRESH_BAT1=75
	#STOP_CHARGE_THRESH_BAT1=80

	# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable
	#RESTORE_THRESHOLDS_ON_BAT=1

	# ------------------------------------------------------------------------------
	# tlp-rdw - Parameters for the radio device wizard
	# Possible devices: bluetooth, wifi, wwan

	# Hints:
	# - Parameters are disabled by default, remove the leading # to enable them.
	# - Separate multiple radio devices with spaces.

	# Radio devices to disable on connect.
	DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
	DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
	DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"

	# Radio devices to enable on disconnect.
	DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
	DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
	DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""

	# Radio devices to enable/disable when docked.
	#DEVICES_TO_ENABLE_ON_DOCK=""
	#DEVICES_TO_DISABLE_ON_DOCK=""

	# Radio devices to enable/disable when undocked.
	#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
	#DEVICES_TO_DISABLE_ON_UNDOCK=""