Skip to content

Instantly share code, notes, and snippets.

Show Gist options
  • Save pdp7/09995be1e30df0a04b9b9cd31420f9d5 to your computer and use it in GitHub Desktop.
Save pdp7/09995be1e30df0a04b9b9cd31420f9d5 to your computer and use it in GitHub Desktop.
boot log for emmc support in 6.5-rc3 on BeagleV Ahead
brom_ver 8
[APP][E] protocol_connect failed, exit.
Starting download of 963784 bytes
downloading of 963784 bytes finished
U-Boot SPL 2020.01-ga239460ff5e5 (Jul 28 2023 - 17:39:55 -0700)
FM[1] lpddr4x singlerank freq=3733 64bit dbi_off=n sdram init
ddr initialized, jump to uboot
image has no header
U-Boot 2020.01-ga239460ff5e5 (Jul 28 2023 - 17:39:55 -0700)
CPU: rv64imafdcvsu
Model: T-HEAD c910 light
DRAM: 4 GiB
C910 CPU FREQ: 750MHz
AHB2_CPUSYS_HCLK FREQ: 250MHz
AHB3_CPUSYS_PCLK FREQ: 125MHz
PERISYS_AHB_HCLK FREQ: 250MHz
PERISYS_APB_PCLK FREQ: 62MHz
GMAC PLL POSTDIV FREQ: 1000MHZ
DPU0 PLL POSTDIV FREQ: 1188MHZ
DPU1 PLL POSTDIV FREQ: 1188MHZ
MMC: sdhci@ffe7080000: 0, sd@ffe7090000: 1
Loading Environment from MMC... OK
Error reading output register
Warning: cannot get lcd-en GPIO
LCD panel cannot be found : -121
splash screen startup cost 15 ms
In: serial
Out: serial
Err: serial
## Resetting to default environment
Saving Environment to MMC... Writing to MMC(0)... OK
Writing GPT: success!
dwc3_gadget_start maximum_speed:5 revision:0x5533330b
dwc3_gadget_start DWC3_DCFG:0x80804
dwc3_gadget_conndone_interrupt speed:0 dwc3_dsts:0x20000
dwc3_gadget_conndone_interrupt speed:0 dwc3_dsts:0x311f0
Writing GPT: success!
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
Starting download of 963784 bytes
request 00000000ffa60500 was not queued to ep1in-bulk
.......
downloading of 963784 bytes finished
request 00000000ffa60500 was not queued to ep1in-bulk
MMC write: dev # 0, block # 0, count 1883 ... 1883 blocks written: OK
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
Starting download of 12742908 bytes
request 00000000ffa60500 was not queued to ep1in-bulk
..........................................................................
.......................
downloading of 12742908 bytes finished
request 00000000ffa60500 was not queued to ep1in-bulk
cmd_parameter: boot, imagesize: 12742908
Flashing sparse image at offset 4096
Flashing Sparse Image
........ wrote 199229440 bytes to 'boot'
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
Starting download of 62914560 bytes
request 00000000ffa60500 was not queued to ep1in-bulk
..........................................................................
..........................................................................
..........................................................................
..........................................................................
..........................................................................
..........................................................................
....................................
downloading of 62914560 bytes finished
request 00000000ffa60500 was not queued to ep1in-bulk
cmd_parameter: root, imagesize: 62914560
Flashing Raw Image
........ wrote 62914560 bytes to 'root'
request 00000000ffa60500 was not queued to ep1in-bulk
request 00000000ffa60500 was not queued to ep1in-bulk
Booting kernel at 0x0000000010000000...
Wrong Image Format for command
ERROR: can't get kernel image!
resetting ...
brom_ver 8
[APP][E] protocol_connect failed, exit.
U-Boot SPL 2020.01-ga239460ff5e5 (Jul 28 2023 - 17:39:55 -0700)
FM[1] lpddr4x singlerank freq=3733 64bit dbi_off=n sdram init
ddr initialized, jump to uboot
image has no header
U-Boot 2020.01-ga239460ff5e5 (Jul 28 2023 - 17:39:55 -0700)
CPU: rv64imafdcvsu
Model: T-HEAD c910 light
DRAM: 4 GiB
C910 CPU FREQ: 750MHz
AHB2_CPUSYS_HCLK FREQ: 250MHz
AHB3_CPUSYS_PCLK FREQ: 125MHz
PERISYS_AHB_HCLK FREQ: 250MHz
PERISYS_APB_PCLK FREQ: 62MHz
GMAC PLL POSTDIV FREQ: 1000MHZ
DPU0 PLL POSTDIV FREQ: 1188MHZ
DPU1 PLL POSTDIV FREQ: 1188MHZ
MMC: sdhci@ffe7080000: 0, sd@ffe7090000: 1
Loading Environment from MMC... OK
Error reading output register
Warning: cannot get lcd-en GPIO
LCD panel cannot be found : -121
splash screen startup cost 16 ms
In: serial
Out: serial
Err: serial
Saving Environment to MMC... Writing to MMC(0)... OK
Net: ethernet@ffe7070000 (eth0) using MAC address - 76:5e:90:9e:3e:6e
eth0: ethernet@ffe7070000ethernet@ffe7070000:0 is connected to ethernet@ffe7070000. Reconnecting to ethernet@ffe7060000
ethernet@ffe7060000 (eth1) using MAC address - 76:5e:90:9e:3e:6f
, eth1: ethernet@ffe7060000
Hit any key to stop autoboot: 2  1  0
50340 bytes read in 2 ms (24 MiB/s)
15748 bytes read in 1 ms (15 MiB/s)
138368 bytes read in 1 ms (132 MiB/s)
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:2...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
208 bytes read in 1 ms (203.1 KiB/s)
1: Linux eMMC
Retrieving file: /Image
15527936 bytes read in 37 ms (400.2 MiB/s)
append: root=/dev/mmcblk0p3 ro rootfstype=ext4 rootwait console=ttyS0,115200 earlycon clk_ignore_unused net.ifnames=0
Retrieving file: /light-beagle.dtb
8901 bytes read in 1 ms (8.5 MiB/s)
## Flattened Device Tree blob at 46000000
Booting using the fdt blob at 0x46000000
Using Device Tree in place at 0000000046000000, end 00000000460052c4
Starting kernel ...
OpenSBI v1.3-31-g0ad866067d78
____ _____ ____ _____
/ __ \ / ____| _ \_ _|
| | | |_ __ ___ _ __ | (___ | |_) || |
| | | | '_ \ / _ \ '_ \ \___ \| _ < | |
| |__| | |_) | __/ | | |____) | |_) || |_
\____/| .__/ \___|_| |_|_____/|____/_____|
| |
|_|
Platform Name : BeagleV Ahead
Platform Features : medeleg
Platform HART Count : 4
Platform IPI Device : aclint-mswi
Platform Timer Device : aclint-mtimer @ 3000000Hz
Platform Console Device : uart8250
Platform HSM Device : ---
Platform PMU Device : ---
Platform Reboot Device : ---
Platform Shutdown Device : ---
Platform Suspend Device : ---
Platform CPPC Device : ---
Firmware Base : 0x0
Firmware Size : 224 KB
Firmware RW Offset : 0x20000
Firmware RW Size : 96 KB
Firmware Heap Offset : 0x2e000
Firmware Heap Size : 40 KB (total), 2 KB (reserved), 9 KB (used), 28 KB (free)
Firmware Scratch Size : 4096 B (total), 760 B (used), 3336 B (free)
Runtime SBI Version : 1.0
Domain0 Name : root
Domain0 Boot HART : 0
Domain0 HARTs : 0*,1*,2*,3*
Domain0 Region00 : 0x000000ffdc008000-0x000000ffdc00bfff M: (I,R,W) S/U: ()
Domain0 Region01 : 0x000000ffdc000000-0x000000ffdc007fff M: (I,R,W) S/U: ()
Domain0 Region02 : 0x0000000000000000-0x000000000001ffff M: (R,X) S/U: ()
Domain0 Region03 : 0x0000000000020000-0x000000000003ffff M: (R,W) S/U: ()
Domain0 Region04 : 0x0000000000000000-0xffffffffffffffff M: () S/U: (R,W,X)
Domain0 Next Address : 0x0000000040200000
Domain0 Next Arg1 : 0x0000000046000000
Domain0 Next Mode : S-mode
Domain0 SysReset : yes
Domain0 SysSuspend : yes
Boot HART ID : 0
Boot HART Domain : root
Boot HART Priv Version : v1.11
Boot HART Base ISA : rv64imafdcvx
Boot HART ISA Extensions : zicntr,zihpm
Boot HART PMP Count : 0
Boot HART PMP Granularity : 0
Boot HART PMP Address Bits: 0
Boot HART MHPM Count : 16
Boot HART MIDELEG : 0x0000000000000222
Boot HART MEDELEG : 0x000000000000b109
[ 0.000000] Linux version 6.5.0-rc3-r20230801-0757-00025-g60631734a049 (pdp7@x1) (riscv64-linux-gnu-gcc (Ubuntu 12.3.0-1ubuntu1~22.04) 12.3.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #188 SMP Fri Aug 4 19:46:23 PDT 2023
[ 0.000000] Machine model: BeagleV Ahead
[ 0.000000] SBI specification v1.0 detected
[ 0.000000] SBI implementation ID=0x1 Version=0x10003
[ 0.000000] SBI TIME extension detected
[ 0.000000] SBI IPI extension detected
[ 0.000000] SBI RFENCE extension detected
[ 0.000000] earlycon: uart0 at MMIO32 0x000000ffe7014000 (options '115200n8')
[ 0.000000] printk: bootconsole [uart0] enabled
[ 0.000000] efi: UEFI not found.
[ 0.000000] OF: reserved mem: 0x0000000000000000..0x000000000001ffff (128 KiB) nomap non-reusable mmode_resv0@0
[ 0.000000] OF: reserved mem: 0x0000000000020000..0x000000000003ffff (128 KiB) nomap non-reusable mmode_resv1@20000
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000000000000-0x00000000ffffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000003ffff]
[ 0.000000] node 0: [mem 0x0000000000040000-0x00000000ffffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000ffffffff]
[ 0.000000] SBI HSM extension detected
[ 0.000000] riscv: base ISA extensions acdfim
[ 0.000000] riscv: ELF capabilities acdfim
[ 0.000000] percpu: Embedded 19 pages/cpu s38312 r8192 d31320 u77824
[ 0.000000] pcpu-alloc: s38312 r8192 d31320 u77824 alloc=19*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Kernel command line: root=/dev/mmcblk0p3 ro rootfstype=ext4 rootwait console=ttyS0,115200 earlycon clk_ignore_unused net.ifnames=0
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 4089072K/4194304K available (5451K kernel code, 4803K rwdata, 2048K rodata, 2168K init, 317K bss, 105232K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] rcu: RCU debug extended QS entry/exit.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] riscv-intc: 64 local interrupts mapped
[ 0.000000] plic: interrupt-controller@ffd8000000: mapped 240 interrupts with 4 handlers for 8 contexts.
[ 0.000000] riscv: providing IPIs using SBI IPI extension
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1623fa770, max_idle_ns: 881590404476 ns
[ 0.000001] sched_clock: 64 bits at 3000kHz, resolution 333ns, wraps every 4398046511097ns
[ 0.008816] Console: colour dummy device 80x25
[ 0.013484] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=12000)
[ 0.023976] pid_max: default: 32768 minimum: 301
[ 0.029020] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.036779] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.047517] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[ 0.055414] riscv: ELF compat mode unsupported
[ 0.055477] ASID allocator using 16 bits (65536 entries)
[ 0.065709] rcu: Hierarchical SRCU implementation.
[ 0.070685] rcu: Max phase no-delay instances is 1000.
[ 0.076653] EFI services will not be available.
[ 0.081798] smp: Bringing up secondary CPUs ...
[ 1.095976] CPU1: failed to come online
[ 2.121475] CPU2: failed to come online
[ 3.147038] CPU3: failed to come online
[ 3.151081] smp: Brought up 1 node, 1 CPU
[ 3.156975] devtmpfs: initialized
[ 3.164512] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 3.174683] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 3.182025] pinctrl core: initialized pinctrl subsystem
[ 3.188579] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 3.195631] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 3.203062] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 3.211353] audit: initializing netlink subsys (disabled)
[ 3.217567] cpuidle: using governor menu
[ 3.221729] audit: type=2000 audit(3.148:1): state=initialized audit_enabled=0 res=1
[ 3.231337] platform soc: Fixed dependency cycle(s) with /soc/interrupt-controller@ffd8000000
[ 3.243590] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[ 3.250693] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
[ 3.259218] clocksource: Switched to clocksource riscv_clocksource
[ 3.279646] NET: Registered PF_INET protocol family
[ 3.285043] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 3.300149] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 3.309066] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 3.317151] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 3.325589] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 3.334615] TCP: Hash tables configured (established 32768 bind 32768)
[ 3.341542] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 3.348415] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 3.356085] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 3.363708] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 3.371348] NET: Registered PF_ALG protocol family
[ 3.376380] io scheduler mq-deadline registered
[ 3.380980] io scheduler kyber registered
[ 3.385205] io scheduler bfq registered
[ 3.477406] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 3.487317] printk: console [ttyS0] disabled
[ 3.492218] ffe7014000.serial: ttyS0 at MMIO 0xffe7014000 (irq = 12, base_baud = 6250000) is a 16550A
[ 3.501684] printk: console [ttyS0] enabled
[ 3.501684] printk: console [ttyS0] enabled
[ 3.510225] printk: bootconsole [uart0] disabled
[ 3.510225] printk: bootconsole [uart0] disabled
[ 3.530484] loop: module loaded
[ 3.534129] mousedev: PS/2 mouse device common for all mice
[ 3.540432] sdhci: Secure Digital Host Controller Interface driver
[ 3.546655] sdhci: Copyright(c) Pierre Ossman
[ 3.551082] Synopsys Designware Multimedia Card Interface Driver
[ 3.557417] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.563421] riscv-pmu-sbi: SBI PMU extension is available
[ 3.568900] riscv-pmu-sbi: 16 firmware and 18 hardware counters
[ 3.577043] NET: Registered PF_INET6 protocol family
[ 3.583388] Segment Routing with IPv6
[ 3.587144] In-situ OAM (IOAM) with IPv6
[ 3.591237] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 3.598032] NET: Registered PF_PACKET protocol family
[ 3.603133] start plist test
[ 3.610899] end plist test
[ 3.631163] clk: Not disabling unused clocks
[ 3.636131] mmc0: SDHCI controller on ffe7080000.mmc [ffe7080000.mmc] using PIO
[ 3.643818] dw-apb-uart ffe7014000.serial: forbid DMA for kernel console
[ 3.650718] Waiting for root device /dev/mmcblk0p3...
[ 3.694764] mmc0: new HS400 MMC card at address 0001
[ 3.700593] mmcblk0: mmc0:0001 TB2916 14.6 GiB
[ 3.710375] mmcblk0: p1 p2 p3
[ 3.714765] mmcblk0boot0: mmc0:0001 TB2916 4.00 MiB
[ 3.721629] mmcblk0boot1: mmc0:0001 TB2916 4.00 MiB
[ 3.728394] mmcblk0rpmb: mmc0:0001 TB2916 4.00 MiB, chardev (251:0)
[ 3.746189] EXT4-fs (mmcblk0p3): orphan cleanup on readonly fs
[ 3.752154] EXT4-fs (mmcblk0p3): mounted filesystem 8ff201a2-f23f-44a4-b218-f156bd960edc ro with ordered data mode. Quota mode: disabled.
[ 3.764608] VFS: Mounted root (ext4 filesystem) readonly on device 179:3.
[ 3.772128] devtmpfs: mounted
[ 3.776135] Freeing unused kernel image (initmem) memory: 2168K
[ 3.783246] Run /sbin/init as init process
[ 3.787373] with arguments:
[ 3.790353] /sbin/init
[ 3.793083] with environment:
[ 3.796247] HOME=/
[ 3.798616] TERM=linux
[ 3.904566] EXT4-fs (mmcblk0p3): re-mounted 8ff201a2-f23f-44a4-b218-f156bd960edc r/w. Quota mode: disabled.
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Saving 256 bits of non-creditable seed for next boot
Welcome to Buildroot
buildroot login: root
# touch THIS_IS_EMMC
# ls -la
total 2
drwx------ 2 root root 1024 Jan 1 00:00 .
drwxr-xr-x 18 root root 1024 Jul 24 2023 ..
-rw-r--r-- 1 root root 0 Jan 1 00:00 THIS_IS_EMMC
#
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment