Skip to content

Instantly share code, notes, and snippets.

@pdp7

pdp7/beaglev beta board boot log for 5.13.0-rc2-starlight.txt

Created May 20, 2021 04:44
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save pdp7/0bf9088d034384d29ba4e8418c9dfd91 to your computer and use it in GitHub Desktop.
Save pdp7/0bf9088d034384d29ba4e8418c9dfd91 to your computer and use it in GitHub Desktop.
Download ZIP
beaglev beta board boot log for 5.13.0-rc2-starlight
Raw
beaglev beta board boot log for 5.13.0-rc2-starlight.txt
[ 0.000000] Linux version 5.13.0-rc2-starlight-drew-307185-g165818ad1fbf (pdp7@x1) (riscv64-linux-gnu-gcc (Ubuntu 10.2.0-8ubuntu1) 10.2.0, GNU ld (GNU Binutils for Ubuntu) 2.35.1) #4 SMP Tue May 18 14:46:11 PDT 2021
[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
[ 0.000000] Machine model: BeagleV Starlight Beta
[ 0.000000] earlycon: uart0 at MMIO32 0x0000000012440000 (options '115200')
[ 0.000000] printk: bootconsole [uart0] enabled
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a0000000, size 640 MiB
[ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x00000000f9000000, size 16 MiB
[ 0.000000] OF: reserved mem: initialized node framebuffer@f9000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x00000000fb000000, size 32 MiB
[ 0.000000] OF: reserved mem: initialized node framebuffer@fb000000, compatible id shared-dma-pool
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000027fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080200000-0x00000000f8ffffff]
[ 0.000000] node 0: [mem 0x00000000f9000000-0x00000000f9ffffff]
[ 0.000000] node 0: [mem 0x00000000fa000000-0x00000000faffffff]
[ 0.000000] node 0: [mem 0x00000000fb000000-0x00000000fcffffff]
[ 0.000000] node 0: [mem 0x00000000fd000000-0x000000027fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
[ 0.000000] On node 0 totalpages: 2096640
[ 0.000000] DMA32 zone: 7161 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 523776 pages, LIFO batch:63
[ 0.000000] Normal zone: 21504 pages used for memmap
[ 0.000000] Normal zone: 1572864 pages, LIFO batch:63
[ 0.000000] SBI specification v0.2 detected
[ 0.000000] SBI implementation ID=0x1 Version=0x9
[ 0.000000] SBI TIME extension detected
[ 0.000000] SBI IPI extension detected
[ 0.000000] SBI RFENCE extension detected
[ 0.000000] software IO TLB: mapped [mem 0x000000009c000000-0x00000000a0000000] (64MB)
[ 0.000000] SBI v0.2 HSM extension detected
[ 0.000000] riscv: ISA extensions acdfim
[ 0.000000] riscv: ELF capabilities acdfim
[ 0.000000] percpu: Embedded 16 pages/cpu s33752 r0 d31784 u65536
[ 0.000000] pcpu-alloc: s33752 r0 d31784 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975
[ 0.000000] Kernel command line: earlycon root=/dev/mmcblk0p2 rootwait stmmac.chain_mode=1
[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Sorting __ex_table...
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 6749156K/8386560K available (6431K kernel code, 4795K rwdata, 2048K rodata, 2137K init, 315K bss, 982044K reserved, 655360K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] riscv-intc: 64 local interrupts mapped
[ 0.000000] plic: disable L2 cache irq 128 in plic
[ 0.000000] plic: disable L2 cache irq 131 in plic
[ 0.000000] plic: disable L2 cache irq 129 in plic
[ 0.000000] plic: disable L2 cache irq 130 in plic
[ 0.000000] plic: disable L2 cache irq 128 in plic
[ 0.000000] plic: disable L2 cache irq 131 in plic
[ 0.000000] plic: disable L2 cache irq 129 in plic
[ 0.000000] plic: disable L2 cache irq 130 in plic
[ 0.000000] plic: interrupt-controller@c000000: mapped 127 interrupts with 2 handlers for 4 contexts.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x171024e6b, max_idle_ns: 440795202301 ns
[ 0.000003] sched_clock: 64 bits at 6MHz, resolution 160ns, wraps every 4398046511040ns
[ 0.007070] Console: colour dummy device 80x25
[ 0.010254] printk: console [tty0] enabled
[ 0.013143] printk: bootconsole [uart0] disabled
[ 0.016555] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=25000)
[ 0.016621] pid_max: default: 32768 minimum: 301
[ 0.017289] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.017882] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.021426] ASID allocator disabled
[ 0.021731] rcu: Hierarchical SRCU implementation.
[ 0.022261] EFI services will not be available.
[ 0.023097] smp: Bringing up secondary CPUs ...
[ 0.024717] smp: Brought up 1 node, 2 CPUs
[ 0.026781] devtmpfs: initialized
[ 0.030658] random: get_random_u32 called from bucket_table_alloc.isra.0+0x50/0x144 with crng_init=0
[ 0.031796] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.031888] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.108874] pinctrl core: initialized pinctrl subsystem
[ 0.109674] NET: Registered protocol family 16
[ 0.132761] raid6: skip pq benchmark and using algorithm int64x8
[ 0.132814] raid6: using intx1 recovery algorithm
[ 0.133573] gpio gpiochip0: (11910000.gpio): added GPIO chardev (254:0)
[ 0.133740] gpio gpiochip0: registered GPIOs 0 to 63 on 11910000.gpio
[ 0.133825] starfive_gpio 11910000.gpio: StarFive GPIO chip registered 0 GPIOs
[ 0.134778] SCSI subsystem initialized
[ 0.135065] usbcore: registered new interface driver usbfs
[ 0.135145] usbcore: registered new interface driver hub
[ 0.135229] usbcore: registered new device driver usb
[ 0.135548] of_get_named_gpiod_flags: parsed 'scl-gpio' property of node '/soc/i2c@118b0000[0]' - status (0)
[ 0.135640] of_get_named_gpiod_flags: parsed 'sda-gpio' property of node '/soc/i2c@118b0000[0]' - status (0)
[ 0.135856] i2c_designware 118b0000.i2c: GPIO lookup for consumer scl
[ 0.135896] i2c_designware 118b0000.i2c: using device tree for GPIO lookup
[ 0.135933] of_get_named_gpiod_flags: can't parse 'scl-gpios' property of node '/soc/i2c@118b0000[0]'
[ 0.136003] of_get_named_gpiod_flags: parsed 'scl-gpio' property of node '/soc/i2c@118b0000[0]' - status (0)
[ 0.136067] gpio gpiochip0: Persistence not supported for GPIO 62
[ 0.136096] i2c_designware 118b0000.i2c: GPIO lookup for consumer sda
[ 0.136117] i2c_designware 118b0000.i2c: using device tree for GPIO lookup
[ 0.136145] of_get_named_gpiod_flags: can't parse 'sda-gpios' property of node '/soc/i2c@118b0000[0]'
[ 0.136204] of_get_named_gpiod_flags: parsed 'sda-gpio' property of node '/soc/i2c@118b0000[0]' - status (0)
[ 0.136257] gpio gpiochip0: Persistence not supported for GPIO 61
[ 0.136282] i2c_designware 118b0000.i2c: running with gpio recovery mode! scl,sda
[ 0.137160] of_get_named_gpiod_flags: parsed 'scl-gpio' property of node '/soc/i2c@118c0000[0]' - status (0)
[ 0.137267] of_get_named_gpiod_flags: parsed 'sda-gpio' property of node '/soc/i2c@118c0000[0]' - status (0)
[ 0.137520] i2c_designware 118c0000.i2c: GPIO lookup for consumer scl
[ 0.137561] i2c_designware 118c0000.i2c: using device tree for GPIO lookup
[ 0.137595] of_get_named_gpiod_flags: can't parse 'scl-gpios' property of node '/soc/i2c@118c0000[0]'
[ 0.137668] of_get_named_gpiod_flags: parsed 'scl-gpio' property of node '/soc/i2c@118c0000[0]' - status (0)
[ 0.137728] gpio gpiochip0: Persistence not supported for GPIO 47
[ 0.137755] i2c_designware 118c0000.i2c: GPIO lookup for consumer sda
[ 0.137776] i2c_designware 118c0000.i2c: using device tree for GPIO lookup
[ 0.137806] of_get_named_gpiod_flags: can't parse 'sda-gpios' property of node '/soc/i2c@118c0000[0]'
[ 0.137866] of_get_named_gpiod_flags: parsed 'sda-gpio' property of node '/soc/i2c@118c0000[0]' - status (0)
[ 0.137921] gpio gpiochip0: Persistence not supported for GPIO 48
[ 0.137945] i2c_designware 118c0000.i2c: running with gpio recovery mode! scl,sda
[ 0.138296] of_get_named_gpiod_flags: parsed 'scl-gpio' property of node '/soc/i2c@12450000[0]' - status (0)
[ 0.138388] of_get_named_gpiod_flags: parsed 'sda-gpio' property of node '/soc/i2c@12450000[0]' - status (0)
[ 0.138674] i2c_designware 12450000.i2c: GPIO lookup for consumer scl
[ 0.138720] i2c_designware 12450000.i2c: using device tree for GPIO lookup
[ 0.138755] of_get_named_gpiod_flags: can't parse 'scl-gpios' property of node '/soc/i2c@12450000[0]'
[ 0.138826] of_get_named_gpiod_flags: parsed 'scl-gpio' property of node '/soc/i2c@12450000[0]' - status (0)
[ 0.138886] gpio gpiochip0: Persistence not supported for GPIO 60
[ 0.138913] i2c_designware 12450000.i2c: GPIO lookup for consumer sda
[ 0.138934] i2c_designware 12450000.i2c: using device tree for GPIO lookup
[ 0.138963] of_get_named_gpiod_flags: can't parse 'sda-gpios' property of node '/soc/i2c@12450000[0]'
[ 0.139020] of_get_named_gpiod_flags: parsed 'sda-gpio' property of node '/soc/i2c@12450000[0]' - status (0)
[ 0.139072] gpio gpiochip0: Persistence not supported for GPIO 59
[ 0.139097] i2c_designware 12450000.i2c: running with gpio recovery mode! scl,sda
[ 0.140981] clocksource: Switched to clocksource riscv_clocksource
[ 0.159424] NET: Registered protocol family 2
[ 0.163923] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.174029] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.174495] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.177155] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 0.182106] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.182868] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.183610] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.184615] NET: Registered protocol family 1
[ 0.186296] RPC: Registered named UNIX socket transport module.
[ 0.186360] RPC: Registered udp transport module.
[ 0.186384] RPC: Registered tcp transport module.
[ 0.186406] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.188420] Initialise system trusted keyrings
[ 0.189020] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[ 0.196147] xor: measuring software checksum speed
[ 0.200848] 8regs : 2186 MB/sec
[ 0.205523] 8regs_prefetch : 2184 MB/sec
[ 0.209848] 32regs : 2342 MB/sec
[ 0.214135] 32regs_prefetch : 2337 MB/sec
[ 0.214166] xor: using function: 32regs (2342 MB/sec)
[ 0.214206] Key type asymmetric registered
[ 0.214233] Asymmetric key parser 'x509' registered
[ 0.214336] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.214565] io scheduler bfq registered
[ 0.216646] dw_axi_dmac_platform 100b0000.dma-controller: DesignWare AXI DMA Controller, 4 channels
[ 0.218412] dw_axi_dmac_platform 10500000.dma-controller: DesignWare AXI DMA Controller, 16 channels
[ 0.219087] L2CACHE: No. of Banks in the cache: 2
[ 0.219144] L2CACHE: No. of ways per bank: 16
[ 0.219166] L2CACHE: Sets per bank: 1024
[ 0.219187] L2CACHE: Bytes per cache block: 64
[ 0.219209] L2CACHE: Index of the largest way enabled: 0
[ 0.219826] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.221351] serial8250 serial8250: no of_node; not parsing pinctrl DT
[ 0.222104] dw-apb-uart 11870000.serial: GPIO lookup for consumer rs485-term
[ 0.222162] dw-apb-uart 11870000.serial: using device tree for GPIO lookup
[ 0.222200] of_get_named_gpiod_flags: can't parse 'rs485-term-gpios' property of node '/soc/serial@11870000[0]'
[ 0.222272] of_get_named_gpiod_flags: can't parse 'rs485-term-gpio' property of node '/soc/serial@11870000[0]'
[ 0.222328] dw-apb-uart 11870000.serial: using lookup tables for GPIO lookup
[ 0.222351] dw-apb-uart 11870000.serial: No GPIO consumer rs485-term found
[ 0.222419] dw-apb-uart 11870000.serial: detected caps 00000000 should be 00000100
[ 0.222448] 11870000.serial: ttyS1 at MMIO 0x11870000 (irq = 6, base_baud = 4640625) is a 16550
[ 0.223498] dw-apb-uart 12440000.serial: GPIO lookup for consumer rs485-term
[ 0.223560] dw-apb-uart 12440000.serial: using device tree for GPIO lookup
[ 0.223598] of_get_named_gpiod_flags: can't parse 'rs485-term-gpios' property of node '/soc/serial@12440000[0]'
[ 0.223671] of_get_named_gpiod_flags: can't parse 'rs485-term-gpio' property of node '/soc/serial@12440000[0]'
[ 0.223727] dw-apb-uart 12440000.serial: using lookup tables for GPIO lookup
[ 0.223748] dw-apb-uart 12440000.serial: No GPIO consumer rs485-term found
[ 0.223803] 12440000.serial: ttyS0 at MMIO 0x12440000 (irq = 7, base_baud = 6250000) is a 16550A
[ 1.185331] printk: console [ttyS0] enabled
[ 1.190738] vic-rng 118d0000.trng: Initialized
[ 1.196533] loop: module loaded
[ 1.219030] tps65086 0-005e: Failed to read revision register
[ 1.223717] tps65086: probe of 0-005e failed with error -121
[ 1.229840] dw_spi_mmio 12410000.spi: DMA init failed
[ 1.235288] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 1.241933] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 1.250934] mdio_bus fixed-0: GPIO lookup for consumer reset
[ 1.255381] mdio_bus fixed-0: using lookup tables for GPIO lookup
[ 1.260203] mdio_bus fixed-0: No GPIO consumer reset found
[ 1.264489] libphy: Fixed MDIO Bus: probed
[ 1.267742] tun: Universal TUN/TAP device driver, 1.6
[ 1.272222] stmmaceth 10020000.ethernet: IRQ eth_lpi not found
[ 1.276988] stmmaceth 10020000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[ 1.285084] stmmaceth 10020000.ethernet: PTP uses main clock
[ 1.290072] stmmaceth 10020000.ethernet: User ID: 0x59, Synopsys ID: 0x37
[ 1.295664] stmmaceth 10020000.ethernet: DWMAC1000
[ 1.299291] stmmaceth 10020000.ethernet: DMA HW capability register supported
[ 1.305155] stmmaceth 10020000.ethernet: RX Checksum Offload Engine supported
[ 1.311014] stmmaceth 10020000.ethernet: COE Type 2
[ 1.314615] stmmaceth 10020000.ethernet: Wake-Up On Lan supported
[ 1.319420] stmmaceth 10020000.ethernet: Enhanced/Alternate descriptors
[ 1.324772] stmmaceth 10020000.ethernet: Enabled extended descriptors
[ 1.329930] stmmaceth 10020000.ethernet: Chain mode enabled
[ 1.334218] stmmaceth 10020000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.340584] stmmaceth 10020000.ethernet: device MAC address 66:34:b0:6c:de:ad
[ 1.346971] mdio_bus stmmac-0: GPIO lookup for consumer reset
[ 1.351513] mdio_bus stmmac-0: using lookup tables for GPIO lookup
[ 1.356431] mdio_bus stmmac-0: No GPIO consumer reset found
[ 1.360736] stmmaceth 10020000.ethernet: GPIO lookup for consumer snps,reset
[ 1.366507] stmmaceth 10020000.ethernet: using device tree for GPIO lookup
[ 1.372122] of_get_named_gpiod_flags: can't parse 'snps,reset-gpios' property of node '/soc/ethernet@10020000[0]'
[ 1.381176] of_get_named_gpiod_flags: can't parse 'snps,reset-gpio' property of node '/soc/ethernet@10020000[0]'
[ 1.390109] stmmaceth 10020000.ethernet: using lookup tables for GPIO lookup
[ 1.395886] stmmaceth 10020000.ethernet: No GPIO consumer snps,reset found
[ 1.401814] mdio_bus stmmac-0:00: GPIO lookup for consumer reset
[ 1.406584] mdio_bus stmmac-0:00: using lookup tables for GPIO lookup
[ 1.411745] mdio_bus stmmac-0:00: No GPIO consumer reset found
[ 1.416448] Micrel KSZ9031 Gigabit PHY stmmac-0:00: no of_node; not parsing pinctrl DT
[ 1.425360] mdio_bus stmmac-0:07: GPIO lookup for consumer reset
[ 1.430131] mdio_bus stmmac-0:07: using lookup tables for GPIO lookup
[ 1.435289] mdio_bus stmmac-0:07: No GPIO consumer reset found
[ 1.440000] Micrel KSZ9031 Gigabit PHY stmmac-0:07: no of_node; not parsing pinctrl DT
[ 1.453148] libphy: stmmac: probed
[ 1.455291] Micrel KSZ9031 Gigabit PHY stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 1.464200] Micrel KSZ9031 Gigabit PHY stmmac-0:07: attached PHY driver (mii_bus:phy_addr=stmmac-0:07, irq=POLL)
[ 1.476549] xhci-hcd xhci-hcd.0.auto: no of_node; not parsing pinctrl DT
[ 1.482231] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.486885] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 1.494495] xhci-hcd xhci-hcd.0.auto: hcc params 0x200073c8 hci version 0x100 quirks 0x0000002000018010
[ 1.502760] xhci-hcd xhci-hcd.0.auto: irq 12, io mem 0x104d0000
[ 1.508135] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.13
[ 1.515182] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.521132] usb usb1: Product: xHCI Host Controller
[ 1.524710] usb usb1: Manufacturer: Linux 5.13.0-rc2-starlight-drew-307185-g165818ad1fbf xhci-hcd
[ 1.532288] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 1.536793] hub 1-0:1.0: USB hub found
[ 1.539450] hub 1-0:1.0: 1 port detected
[ 1.542826] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.547466] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 1.553920] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 1.559396] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.566694] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.13
[ 1.573711] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.579653] usb usb2: Product: xHCI Host Controller
[ 1.583266] usb usb2: Manufacturer: Linux 5.13.0-rc2-starlight-drew-307185-g165818ad1fbf xhci-hcd
[ 1.590851] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 1.595342] hub 2-0:1.0: USB hub found
[ 1.597976] hub 2-0:1.0: 1 port detected
[ 1.601937] usbcore: registered new interface driver uas
[ 1.606172] usbcore: registered new interface driver usb-storage
[ 1.610939] i2c /dev entries driver
[ 1.614395] sfc_temp_sensor 124a0000.tmpsensor: probe
[ 1.628437] temp(c): 39.39
[ 1.630364] pwrseq_simple wifi-pwrseq: GPIO lookup for consumer reset
[ 1.635605] pwrseq_simple wifi-pwrseq: using device tree for GPIO lookup
[ 1.641071] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/wifi-pwrseq[0]' - status (0)
[ 1.649501] gpio gpiochip0: Persistence not supported for GPIO 37
[ 1.654602] Synopsys Designware Multimedia Card Interface Driver
[ 1.659796] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/led-ack[0]' - status (0)
[ 1.659827] dw_mmc 10000000.mmc: IDMAC supports 32-bit address mode.
[ 1.659852] gpio gpiochip0: Persistence not supported for GPIO 43
[ 1.667868] dw_mmc 10000000.mmc: Using internal DMA controller.
[ 1.672915] gpio-43 (?): no flags found for gpios
[ 1.677737] dw_mmc 10000000.mmc: Version ID is 290a
[ 1.683619] NET: Registered protocol family 10
[ 1.685861] dw_mmc 10000000.mmc: DW MMC controller at irq 29,32 bit host data width,32 deep fifo
[ 1.697384] dw_mmc 10010000.mmc: IDMAC supports 32-bit address mode.
[ 1.700226] dw_mmc 10000000.mmc: GPIO lookup for consumer cd
[ 1.705262] dw_mmc 10010000.mmc: Using internal DMA controller.
[ 1.709571] dw_mmc 10000000.mmc: using device tree for GPIO lookup
[ 1.714230] dw_mmc 10010000.mmc: Version ID is 290a
[ 1.719107] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/soc/mmc@10000000[0]'
[ 1.722776] dw_mmc 10010000.mmc: DW MMC controller at irq 30,32 bit host data width,32 deep fifo
[ 1.730618] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/soc/mmc@10000000[0]'
[ 1.730666] dw_mmc 10000000.mmc: using lookup tables for GPIO lookup
[ 1.738252] dw_mmc 10010000.mmc: GPIO lookup for consumer wp
[ 1.745920] dw_mmc 10000000.mmc: No GPIO consumer cd found
[ 1.745941] dw_mmc 10000000.mmc: GPIO lookup for consumer wp
[ 1.751048] dw_mmc 10010000.mmc: using device tree for GPIO lookup
[ 1.755386] dw_mmc 10000000.mmc: using device tree for GPIO lookup
[ 1.759666] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/soc/mmc@10010000[0]'
[ 1.763957] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/soc/mmc@10000000[0]'
[ 1.768880] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/soc/mmc@10010000[0]'
[ 1.773762] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/soc/mmc@10000000[0]'
[ 1.781618] dw_mmc 10010000.mmc: using lookup tables for GPIO lookup
[ 1.789438] dw_mmc 10000000.mmc: using lookup tables for GPIO lookup
[ 1.797224] dw_mmc 10010000.mmc: No GPIO consumer wp found
[ 1.804939] dw_mmc 10000000.mmc: No GPIO consumer wp found
[ 1.805011] mmc_host mmc0: card is polling.
[ 1.810064] dw_mmc 10010000.mmc: allocated mmc-pwrseq
[ 1.827873] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[ 1.830222] mmc_host mmc1: card is non-removable.
[ 1.844534] Segment Routing with IPv6
[ 1.847157] NET: Registered protocol family 17
[ 1.850627] Loading compiled-in X.509 certificates
[ 1.856208] Btrfs loaded, crc32c=crc32c-generic, zoned=no
[ 1.862795] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[ 1.871678] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 1.880340] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 1.889257] dw-apb-uart 12440000.serial: forbid DMA for kernel console
[ 1.894888] Waiting for root device /dev/mmcblk0p2...
[ 1.901069] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 1.909824] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 1.915424] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.921026] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.927710] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.934976] mmc1: queuing unknown CIS tuple 0x81 (9 bytes)
[ 1.945085] mmc_host mmc0: Bus speed (slot 0) = 100000000Hz (slot req 10000000Hz, actual 10000000HZ div = 5)
[ 1.953872] mmc0: new high speed SDHC card at address e624
[ 1.958449] mmcblk mmc0:e624: no of_node; not parsing pinctrl DT
[ 1.960333] random: fast init done
[ 1.967883] mmcblk0: mmc0:e624 SL16G 14.8 GiB
[ 1.973590] mmcblk0: p1 p2
[ 2.015995] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
[ 2.018098] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 10000000Hz, actual 10000000HZ div = 5)
[ 2.022094] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
[ 2.035207] mmc1: new high speed SDIO card at address 0001
[ 2.041080] mmcblk mmc1:0001: no of_node; not parsing pinctrl DT
[ 2.046875] brcmfmac mmc1:0001:2: no of_node; not parsing pinctrl DT
[ 2.060680] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/2
[ 2.080978] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice= 4.02
[ 2.088011] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.093927] usb 1-1: Product: USB2.0 Hub
[ 2.096623] usb 1-1: Manufacturer: GenesysLogic
[ 2.101391] usb 1-1: no of_node; not parsing pinctrl DT
[ 2.107050] hub 1-1:1.0: no of_node; not parsing pinctrl DT
[ 2.111551] hub 1-1:1.0: USB hub found
[ 2.115130] hub 1-1:1.0: 4 ports detected
[ 2.201339] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 2.211401] EXT4-fs (mmcblk0p2): recovery complete
[ 2.221318] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled.
[ 2.229392] usb 2-1: New USB device found, idVendor=05e3, idProduct=0616, bcdDevice= 4.02
[ 2.230285] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 2.237139] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.248612] usb 2-1: Product: USB3.0 Hub
[ 2.251295] usb 2-1: Manufacturer: GenesysLogic
[ 2.255349] usb 2-1: no of_node; not parsing pinctrl DT
[ 2.261140] hub 2-1:1.0: no of_node; not parsing pinctrl DT
[ 2.265629] hub 2-1:1.0: USB hub found
[ 2.268615] hub 2-1:1.0: 4 ports detected
[ 2.285629] devtmpfs: mounted
[ 2.296773] Freeing unused kernel memory: 2136K
[ 2.302598] Checked W+X mappings: passed, no W+X pages found
[ 2.307030] rodata_test: all tests were successful
[ 2.310564] Run /sbin/init as init process
[ 2.313391] with arguments:
[ 2.315062] /sbin/init
[ 2.316475] with environment:
[ 2.318340] HOME=/
[ 2.319407] TERM=linux
[ 3.201933] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
[ 4.219247] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50
[ 5.532166] systemd[1]: System time before build time, advancing clock.
[ 5.870493] systemd[1]: systemd v246.6-3.0.riscv64.fc33 running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD -SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 5.893949] systemd[1]: Detected architecture riscv64.
[ 5.947414] systemd[1]: Set hostname to <fedora-starfive>.
[ 6.628460] random: zram-generator: uninitialized urandom read (16 bytes read)
[ 7.332415] zram_generator::generator[92]: Creating dev-zram0.swap for /dev/zram0 (3616MB)
[ 9.249293] random: lvmconfig: uninitialized urandom read (4 bytes read)
[ 9.336846] systemd[70]: /usr/lib/systemd/system-generators/zram-generator failed with exit status 1.
[ 10.916504] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-pre-udev.service:27: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 10.937224] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-pre-udev.service:28: Standard output type syslog+console is obsolete, automatically updating to journal+console. Please update your unit file, and consider removing the setting altogether.
[ 10.964040] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-pre-trigger.service:23: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 10.985068] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-pre-trigger.service:24: Standard output type syslog+console is obsolete, automatically updating to journal+console. Please update your unit file, and consider removing the setting altogether.
[ 11.012391] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-pre-pivot.service:30: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.033171] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-pre-pivot.service:31: Standard output type syslog+console is obsolete, automatically updating to journal+console. Please update your unit file, and consider removing the setting altogether.
[ 11.077745] systemd[1]: /usr/lib/systemd/system/gssproxy.service:13: PIDFile= references a path below legacy directory /var/run/, updating /var/run/gssproxy.pid → /run/gssproxy.pid; please update the unit file accordingly.
[ 11.189231] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-pre-mount.service:22: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.209974] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-pre-mount.service:23: Standard output type syslog+console is obsolete, automatically updating to journal+console. Please update your unit file, and consider removing the setting altogether.
[ 11.241472] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-mount.service:22: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.261890] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-mount.service:23: Standard output type syslog+console is obsolete, automatically updating to journal+console. Please update your unit file, and consider removing the setting altogether.
[ 11.287914] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-initqueue.service:24: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.309003] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-initqueue.service:25: Standard output type syslog+console is obsolete, automatically updating to journal+console. Please update your unit file, and consider removing the setting altogether.
[ 11.335146] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-cmdline.service:26: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.355746] systemd[1]: /usr/lib/dracut/modules.d/98dracut-systemd/dracut-cmdline.service:27: Standard output type syslog+console is obsolete, automatically updating to journal+console. Please update your unit file, and consider removing the setting altogether.
[ 11.431520] systemd[1]: /usr/lib/systemd/system/plymouth-start.service:15: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed.
[ 11.721923] systemd[1]: /usr/lib/systemd/system/ip6tables.service:14: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.740473] systemd[1]: /usr/lib/systemd/system/ip6tables.service:15: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.762247] systemd[1]: /usr/lib/systemd/system/iptables.service:14: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.780677] systemd[1]: /usr/lib/systemd/system/iptables.service:15: Standard output type syslog is obsolete, automatically updating to journal. Please update your unit file, and consider removing the setting altogether.
[ 11.857131] systemd[1]: Queued start job for default target Graphical Interface.
[ 11.867213] random: systemd: uninitialized urandom read (16 bytes read)
[ 11.873532] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
[ 11.884668] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[ 11.895285] systemd[1]: Created slice system-getty.slice.
[ 11.917367] random: systemd: uninitialized urandom read (16 bytes read)
[ 11.924493] systemd[1]: Created slice system-modprobe.slice.
[ 11.945351] random: systemd: uninitialized urandom read (16 bytes read)
[ 11.952436] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ 11.974886] systemd[1]: Created slice system-sshd\x2dkeygen.slice.
[ 11.999021] systemd[1]: Created slice system-swap\x2dcreate.slice.
[ 12.022640] systemd[1]: Created slice User and Session Slice.
[ 12.045928] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 12.069679] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
[ 12.081488] systemd[1]: Reached target Slices.
[ 12.098340] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 12.122411] systemd[1]: Listening on LVM2 poll daemon socket.
[ 12.169870] systemd[1]: Listening on multipathd control socket.
[ 12.199214] systemd[1]: Listening on Process Core Dump Socket.
[ 12.221975] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 12.246026] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 12.254200] systemd[1]: Listening on Journal Socket (/dev/log).
[ 12.274653] systemd[1]: Listening on Journal Socket.
[ 12.290705] systemd[1]: Listening on udev Control Socket.
[ 12.310146] systemd[1]: Listening on udev Kernel Socket.
[ 12.330489] systemd[1]: Listening on User Database Manager Socket.
[ 12.354299] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 12.368572] systemd[1]: Mounting POSIX Message Queue File System...
[ 12.397198] systemd[1]: Mounting Kernel Debug File System...
[ 12.425125] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[ 12.433518] systemd[1]: Condition check resulted in Kernel Module supporting RPCSEC_GSS being skipped.
[ 12.442711] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped.
[ 12.459867] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[ 12.493975] systemd[1]: Starting Load Kernel Module drm...
[ 12.524539] systemd[1]: Starting Preprocess NFS configuration convertion...
[ 12.573541] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 12.606701] systemd[1]: Starting Load Kernel Modules...
[ 12.628728] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 12.657736] systemd[1]: Condition check resulted in Repartition Root Disk being skipped.
[ 12.686075] systemd[1]: Starting Coldplug All udev Devices...
[ 12.708485] systemd[1]: Starting Setup Virtual Console...
[ 12.783177] systemd[1]: Mounted POSIX Message Queue File System.
[ 12.827332] systemd[1]: Mounted Kernel Debug File System.
[ 12.856187] systemd[1]: modprobe@drm.service: Succeeded.
[ 12.871204] systemd[1]: Finished Load Kernel Module drm.
[ 12.887737] systemd[1]: nfs-convert.service: Succeeded.
[ 12.894944] systemd[1]: Finished Preprocess NFS configuration convertion.
[ 12.926777] systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
[ 12.936881] systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
[ 12.947079] systemd[1]: Failed to start Load Kernel Modules.
[ 12.978697] systemd[1]: Condition check resulted in FUSE Control File System being skipped.
[ 12.989731] systemd[1]: Condition check resulted in Kernel Configuration File System being skipped.
[ 13.006498] systemd[1]: Starting Apply Kernel Variables...
[ 13.435886] systemd[1]: Finished Apply Kernel Variables.
[ 13.579903] systemd[1]: Finished Coldplug All udev Devices.
[ 13.610997] systemd[1]: Starting Wait for udev To Complete Device Initialization...
[ 13.707435] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null). Quota mode: disabled.
[ 13.734557] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 13.758671] systemd[1]: Condition check resulted in OSTree Remount OS/ Bind Mounts being skipped.
[ 13.769906] systemd[1]: Condition check resulted in First Boot Wizard being skipped.
[ 13.835956] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[ 13.856296] systemd[1]: Starting Load/Save Random Seed...
[ 13.881928] systemd[1]: Condition check resulted in Create System Users being skipped.
[ 13.906634] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 14.366960] systemd[1]: Finished Setup Virtual Console.
[ 14.580458] systemd[1]: Finished Create Static Device Nodes in /dev.
[ 14.608280] systemd[1]: Started Entropy Daemon based on the HAVEGE algorithm.
[ 14.638745] systemd[1]: Starting Journal Service...
[ 14.664621] systemd[1]: Starting Rule-based Manager for Device Events and Files...
[ 15.501922] systemd[1]: Started Journal Service.
[ 15.721069] random: crng init done
[ 15.723256] random: 5 urandom warning(s) missed due to ratelimiting
[ 19.137898] EXT4-fs (mmcblk0p1): recovery complete
[ 19.141586] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled.
[ 19.150522] ext4 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff)
[ 130.667027] stmmaceth 10020000.ethernet eth0: PHY [stmmac-0:00] driver [Micrel KSZ9031 Gigabit PHY] (irq=POLL)
[ 130.682900] stmmaceth 10020000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 130.691224] dwmac1000: Master AXI performs fixed burst length
[ 130.695880] stmmaceth 10020000.ethernet eth0: No Safety Features support found
[ 130.701980] stmmaceth 10020000.ethernet eth0: No MAC Management Counters available
[ 130.708356] stmmaceth 10020000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 130.719132] stmmaceth 10020000.ethernet eth0: configuring for phy/rgmii-txid link mode
[riscv@fedora-starfive ~]$
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment