-
-
Save pdp7/5a03d4bc4566791cc51584d22e2de0bf to your computer and use it in GitHub Desktop.
mender-log.txt
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
U-Boot SPL 2020.01 (Jan 06 2020 - 20:56:31 +0000) | |
Trying to boot from MMC1 | |
U-Boot 2020.01 (Jan 06 2020 - 20:56:31 +0000) | |
CPU : AM335X-GP rev 2.1 | |
Model: TI AM335x BeagleBone Black | |
DRAM: 512 MiB | |
WDT: Started with servicing (60s timeout) | |
NAND: 0 MiB | |
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 | |
Loading Environment from FAT... *** Warning - bad CRC, using default environment | |
<ethaddr> not set. Validating first E-fuse MAC | |
Net: eth0: ethernet@4a100000 | |
Warning: usb_ether MAC addresses don't match: | |
Address in ROM is de:ad:be:ef:00:01 | |
Address in environment is 1c:ba:8c:9b:be:b6 | |
, eth1: usb_ether | |
Hit any key to stop autoboot: 2 1 0 | |
switch to partitions #0, OK | |
mmc0 is current device | |
SD/MMC found on device 0 | |
switch to partitions #0, OK | |
mmc0 is current device | |
Scanning mmc 0:1... | |
58300 bytes read in 7 ms (7.9 MiB/s) | |
58300 bytes read in 9 ms (6.2 MiB/s) | |
Found EFI removable media binary efi/boot/bootarm.efi | |
7[r[999;999H[6n8Scanning disk mmc@48060000.blk... | |
Scanning disk mmc@481d8000.blk... | |
Found 10 disks | |
BootOrder not defined | |
EFI boot manager: Cannot load any image | |
385024 bytes read in 29 ms (12.7 MiB/s) | |
[?25h[0;30;47mWelcome to GRUB! | |
[0;37;40m[0;37;40m[0;37;40mlock: OK | |
lock: OK | |
EFI stub: Booting Linux Kernel... | |
EFI stub: Using DTB from configuration table | |
EFI stub: Exiting boot services and installing virtual address map... | |
Booting Linux on physical CPU 0x0 | |
Linux version 5.4.58-yocto-standard (oe-user@oe-host) (gcc version 9.3.0 (GCC)) #1 PREEMPT Sun Aug 16 22:40:50 UTC 2020 | |
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d | |
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache | |
OF: fdt: Machine model: TI AM335x BeagleBone Black | |
Memory policy: Data cache writeback | |
efi: Getting EFI parameters from FDT: | |
efi: EFI v2.80 by Das U-Boot | |
efi: SMBIOS=0x9cf21000 MEMRESERVE=0x94d85040 | |
cma: Reserved 16 MiB at 0x9e800000 | |
CPU: All CPU(s) started in SVC mode. | |
AM335X ES2.1 (sgx neon) | |
Built 1 zonelists, mobility grouping on. Total pages: 129664 | |
Kernel command line: BOOT_IMAGE=(hd0,2)/boot/zImage root=/dev/mmcblk0p2 console=tty0,115200n8 console=ttyS0,115200n8 console=ttyO0,115200n8 console=ttyAMA0,115200n8 rootwait | |
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) | |
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) | |
mem auto-init: stack:off, heap alloc:off, heap free:off | |
Memory: 484556K/523264K available (10240K kernel code, 940K rwdata, 3532K rodata, 1024K init, 586K bss, 22324K reserved, 16384K cma-reserved, 0K highmem) | |
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 | |
ftrace: allocating 36051 entries in 71 pages | |
rcu: Preemptible hierarchical RCU implementation. | |
Tasks RCU enabled. | |
rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. | |
NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 | |
IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts | |
random: get_random_bytes called from start_kernel+0x2bc/0x4ec with crng_init=0 | |
OMAP clockevent source: timer2 at 24000000 Hz | |
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns | |
clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns | |
OMAP clocksource: timer1 at 24000000 Hz | |
timer_probe: no matching timers found | |
Console: colour dummy device 80x30 | |
printk: console [tty0] enabled | |
Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) | |
pid_max: default: 32768 minimum: 301 | |
LSM: Security Framework initializing | |
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) | |
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) | |
CPU: Testing write buffer coherency: ok | |
CPU0: Spectre v2: using BPIALL workaround | |
Setting up static identity map for 0x80100000 - 0x80100060 | |
rcu: Hierarchical SRCU implementation. | |
Remapping and enabling EFI services. | |
devtmpfs: initialized | |
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 | |
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns | |
futex hash table entries: 256 (order: -1, 3072 bytes, linear) | |
xor: measuring software checksum speed | |
arm4regs : 1221.600 MB/sec | |
8regs : 905.200 MB/sec | |
32regs : 1174.800 MB/sec | |
xor: using function: arm4regs (1221.600 MB/sec) | |
pinctrl core: initialized pinctrl subsystem | |
SMBIOS 3.0 present. | |
DMI: ti am335x/am335x, BIOS 2020.01 01/06/2020 | |
NET: Registered protocol family 16 | |
DMA: preallocated 256 KiB pool for atomic coherent allocations | |
l3-aon-clkctrl:0000:0: failed to disable | |
cpuidle: using governor ladder | |
cpuidle: using governor menu | |
hw-breakpoint: debug architecture 0x4 unsupported. | |
Serial: AMBA PL011 UART driver | |
raid6: int32x8 gen() 151 MB/s | |
raid6: int32x8 xor() 102 MB/s | |
raid6: int32x4 gen() 160 MB/s | |
raid6: int32x4 xor() 113 MB/s | |
raid6: int32x2 gen() 270 MB/s | |
raid6: int32x2 xor() 190 MB/s | |
raid6: int32x1 gen() 226 MB/s | |
raid6: int32x1 xor() 161 MB/s | |
raid6: using algorithm int32x2 gen() 270 MB/s | |
raid6: .... xor() 190 MB/s, rmw enabled | |
raid6: using intx1 recovery algorithm | |
edma 49000000.edma: TI EDMA DMA engine driver | |
SCSI subsystem initialized | |
usbcore: registered new interface driver usbfs | |
usbcore: registered new interface driver hub | |
usbcore: registered new device driver usb | |
Registered efivars operations | |
clocksource: Switched to clocksource timer1 | |
NET: Registered protocol family 2 | |
tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) | |
TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) | |
TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) | |
TCP: Hash tables configured (established 4096 bind 4096) | |
UDP hash table entries: 256 (order: 0, 4096 bytes, linear) | |
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) | |
NET: Registered protocol family 1 | |
RPC: Registered named UNIX socket transport module. | |
RPC: Registered udp transport module. | |
RPC: Registered tcp transport module. | |
RPC: Registered tcp NFSv4.1 backchannel transport module. | |
hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available | |
Initialise system trusted keyrings | |
workingset: timestamp_bits=14 max_order=17 bucket_order=3 | |
NFS: Registering the id_resolver key type | |
Key type id_resolver registered | |
Key type id_legacy registered | |
Key type cifs.idmap registered | |
Key type asymmetric registered | |
Asymmetric key parser 'x509' registered | |
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) | |
io scheduler mq-deadline registered | |
io scheduler kyber registered | |
OMAP GPIO hardware version 0.1 | |
ti-sysc 4a101200.target-module: OCP softreset timed out | |
ti-sysc 4a101200.target-module: OCP softreset timed out | |
pinctrl-single 44e10800.pinmux: 142 pins, size 568 | |
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled | |
printk: console [ttyS0] disabled | |
44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 29, base_baud = 3000000) is a 8250 | |
random: fast init done | |
printk: console [ttyS0] enabled | |
omap_rng 48310000.rng: Random Number Generator ver. 20 | |
random: crng init done | |
brd: module loaded | |
mtdoops: mtd device (mtddev=name/number) must be supplied | |
libphy: Fixed MDIO Bus: probed | |
ti-sysc 4a101200.target-module: OCP softreset timed out | |
davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 | |
libphy: 4a101000.mdio: probed | |
davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 | |
cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 | |
cpsw 4a100000.ethernet: ALE Table size 1024 | |
cpsw 4a100000.ethernet: Detected MACID = 1c:ba:8c:9b:be:b4 | |
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
ehci-omap: OMAP-EHCI Host Controller driver | |
usbcore: registered new interface driver usb-storage | |
am335x-phy-driver 47401300.usb-phy: 47401300.usb-phy supply vcc not found, using dummy regulator | |
am335x-phy-driver 47401b00.usb-phy: 47401b00.usb-phy supply vcc not found, using dummy regulator | |
omap_rtc 44e3e000.rtc: registered as rtc0 | |
i2c /dev entries driver | |
omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec | |
omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) | |
omap_hsmmc 48060000.mmc: Got CD GPIO | |
omap_hsmmc 47810000.mmc: RX DMA channel request failed | |
usbcore: registered new interface driver usbhid | |
usbhid: USB HID core driver | |
oprofile: using arm/armv7 | |
u32 classifier | |
input device check on | |
Actions configured | |
NET: Registered protocol family 10 | |
Segment Routing with IPv6 | |
mmc0: host does not support reading read-only switch, assuming write-enable | |
sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver | |
NET: Registered protocol family 17 | |
mmc0: new high speed SDHC card at address aaaa | |
Key type dns_resolver registered | |
ThumbEE CPU extension supported. | |
mmcblk0: mmc0:aaaa SU16G 14.8 GiB | |
omap_voltage_late_init: Voltage driver support not added | |
mmcblk0: p1 p2 p3 p4 | |
Loading compiled-in X.509 certificates | |
Key type ._fscrypt registered | |
Key type .fscrypt registered | |
Btrfs loaded, crc32c=crc32c-generic | |
Key type encrypted registered | |
mmc1: new high speed MMC card at address 0001 | |
mmcblk1: mmc1:0001 MMC04G 3.66 GiB | |
mmcblk1boot0: mmc1:0001 MMC04G partition 1 1.00 MiB | |
mmcblk1boot1: mmc1:0001 MMC04G partition 2 1.00 MiB | |
mmcblk1rpmb: mmc1:0001 MMC04G partition 3 128 KiB, chardev (249:0) | |
mmcblk1: p1 p2 p3 p4 | |
tps65217 0-0024: TPS65217 ID 0xe version 1.2 | |
tda998x 0-0070: found TDA19988 | |
tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_ops) | |
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013). | |
[drm] No driver support for vblank timestamp query. | |
[drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 | |
[drm] Cannot find any crtc or sizes | |
omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz | |
[drm] Cannot find any crtc or sizes | |
omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz | |
musb-hdrc musb-hdrc.1: MUSB HDRC host driver | |
musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 | |
hub 1-0:1.0: USB hub found | |
hub 1-0:1.0: 1 port detected | |
printk: console [netcon0] enabled | |
netconsole: network logging started | |
omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) | |
cfg80211: Loading compiled-in X.509 certificates for regulatory database | |
cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' | |
platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 | |
cfg80211: failed to load regulatory.db | |
EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem | |
EXT4-fs (mmcblk0p2): write access will be enabled during recovery | |
EXT4-fs (mmcblk0p2): recovery complete | |
EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) | |
VFS: Mounted root (ext4 filesystem) readonly on device 179:2. | |
devtmpfs: mounted | |
Freeing unused kernel memory: 1024K | |
Run /sbin/init as init process | |
systemd[1]: systemd 244.5+ running in system mode. (-PAM -AUDIT -SELINUX +IMA -APPARMOR -SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) | |
systemd[1]: Detected architecture arm. | |
systemd[1]: Set hostname to <beaglebone-yocto>. | |
systemd[1]: Created slice system-getty.slice. | |
systemd[1]: Created slice system-serial\x2dgetty.slice. | |
systemd[1]: Created slice system-systemd\x2dfsck.slice. | |
systemd[1]: Created slice User and Session Slice. | |
systemd[1]: Started Dispatch Password Requests to Console Directory Watch. | |
systemd[1]: Started Forward Password Requests to Wall Directory Watch. | |
systemd[1]: Reached target Paths. | |
systemd[1]: Reached target Remote File Systems. | |
systemd[1]: Reached target Slices. | |
systemd[1]: Reached target Swap. | |
systemd[1]: Listening on RPCbind Server Activation Socket. | |
systemd[1]: Reached target RPC Port Mapper. | |
systemd[1]: Listening on Syslog Socket. | |
systemd[1]: Listening on initctl Compatibility Named Pipe. | |
systemd[1]: Condition check resulted in Journal Audit Socket being skipped. | |
systemd[1]: Listening on Journal Socket (/dev/log). | |
systemd[1]: Listening on Journal Socket. | |
systemd[1]: Listening on Network Service Netlink Socket. | |
systemd[1]: Listening on udev Control Socket. | |
systemd[1]: Listening on udev Kernel Socket. | |
systemd[1]: Condition check resulted in Huge Pages File System being skipped. | |
systemd[1]: Mounting POSIX Message Queue File System... | |
systemd[1]: Mounting Kernel Debug File System... | |
systemd[1]: Mounting Temporary Directory (/tmp)... | |
systemd[1]: Starting Create list of static device nodes for the current kernel... | |
systemd[1]: Starting Mender service to grow data partition size... | |
systemd[1]: Starting Start psplash boot splash screen... | |
systemd[1]: Starting RPC Bind... | |
systemd[1]: Starting File System Check on Root Device... | |
systemd[1]: Starting Journal Service... | |
systemd[1]: Condition check resulted in Load Kernel Modules being skipped. | |
systemd[1]: Condition check resulted in FUSE Control File System being skipped. | |
systemd[1]: Condition check resulted in Kernel Configuration File System being skipped. | |
systemd[1]: Starting Apply Kernel Variables... | |
systemd[1]: Starting udev Coldplug all Devices... | |
systemd[1]: Started RPC Bind. | |
systemd[1]: Mounted POSIX Message Queue File System. | |
systemd[1]: Mounted Kernel Debug File System. | |
systemd[1]: Mounted Temporary Directory (/tmp). | |
systemd[1]: Started Create list of static device nodes for the current kernel. | |
systemd[1]: Started Mender service to grow data partition size. | |
systemd[1]: psplash-start.service: Main process exited, code=exited, status=255/EXCEPTION | |
systemd[1]: psplash-start.service: Failed with result 'exit-code'. | |
systemd[1]: Failed to start Start psplash boot splash screen. | |
systemd[1]: Dependency failed for Start psplash-systemd progress communication helper. | |
systemd[1]: psplash-systemd.service: Job psplash-systemd.service/start failed with result 'dependency'. | |
systemd[1]: Started Journal Service. | |
EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) | |
systemd-journald[110]: Received client request to flush runtime journal. | |
davinci-mcasp 48038000.mcasp: IRQ common not found | |
ti-sysc 4a101200.target-module: OCP softreset timed out | |
asoc-simple-card sound: i2s-hifi <-> 48038000.mcasp mapping ok | |
ti-sysc 4a101200.target-module: OCP softreset timed out | |
ti-sysc 4a101200.target-module: OCP softreset timed out | |
ti-sysc 4a101200.target-module: OCP softreset timed out | |
ti-sysc 4a101200.target-module: OCP softreset timed out | |
cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) | |
SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) | |
EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null) | |
EXT4-fs (mmcblk0p4): resizing filesystem from 15074816 to 15074816 blocks | |
cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off | |
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready | |
Poky (Yocto Project Reference Distro) 3.1.10 beaglebone-yocto ttyS0 | |
beaglebone-yocto login: root | |
7[r[999;999H[6n8root@beaglebone-yocto:~# |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment