Marlin-da42f27c9e6ffe5bf2501c78ad23edf7a82e9f35 for my Monoprice Maker Select V2 with MKS SBASE V1.3

Marlin-da42f27c9e6ffe5bf2501c78ad23edf7a82e9f35.diff

diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 6f722714c..652fa0b91 100644
--- Marlin/Configuration.h
+++ Marlin/Configuration.h
@@ -104,7 +104,7 @@
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#define SERIAL_PORT 0
+#define SERIAL_PORT -1
 
 /**
  * Select a secondary serial port on the board to use for communication with the host.
@@ -132,12 +132,12 @@
 // The following define selects which electronics board you have.
 // Please choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define MOTHERBOARD BOARD_MKS_SBASE
 #endif
 
 // Optional custom name for your RepStrap or other custom machine
 // Displayed in the LCD "Ready" message
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+#define CUSTOM_MACHINE_NAME "Monoprice"
 
 // Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
 // You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
@@ -150,7 +150,7 @@
 #define EXTRUDERS 1
 
 // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
-#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
+#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
 
 // For Cyclops or any "multi-extruder" that shares a single nozzle.
 //#define SINGLENOZZLE
@@ -333,7 +333,7 @@
 #define TEMP_SENSOR_3 0
 #define TEMP_SENSOR_4 0
 #define TEMP_SENSOR_5 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_CHAMBER 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
@@ -400,9 +400,9 @@
   // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 
   // Ultimaker
-  #define DEFAULT_Kp 22.2
-  #define DEFAULT_Ki 1.08
-  #define DEFAULT_Kd 114
+  //#define DEFAULT_Kp 22.2
+  //#define DEFAULT_Ki 1.08
+  //#define DEFAULT_Kd 114
 
   // MakerGear
   //#define DEFAULT_Kp 7.0
@@ -414,6 +414,11 @@
   //#define DEFAULT_Ki 2.25
   //#define DEFAULT_Kd 440
 
+  // Monoprice I3
+  #define DEFAULT_Kp 22.001600
+  #define DEFAULT_Ki 1.160269
+  #define DEFAULT_Kd 104.301331
+
 #endif // PIDTEMP
 
 //===========================================================================
@@ -433,7 +438,7 @@
  * heater. If your configuration is significantly different than this and you don't understand
  * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  */
-//#define PIDTEMPBED
+#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
@@ -561,9 +566,9 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
 #define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
 #define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
@@ -640,7 +645,7 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 4000, 500 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 160, 160, 800, 180 }
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -655,7 +660,7 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 800, 800, 100, 10000 }
 
 /**
  * Default Acceleration (change/s) change = mm/s
@@ -665,7 +670,7 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_ACCELERATION          800    // X, Y, Z and E acceleration for printing moves
 #define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
 #define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
 
@@ -904,8 +909,8 @@
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
 #define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+#define INVERT_Y_DIR false
+#define INVERT_Z_DIR true
 
 // @section extruder
 
@@ -1046,7 +1051,7 @@
 //#define AUTO_BED_LEVELING_LINEAR
 //#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
-//#define MESH_BED_LEVELING
+#define MESH_BED_LEVELING
 
 /**
  * Normally G28 leaves leveling disabled on completion. Enable
@@ -1168,7 +1173,7 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
@@ -1177,7 +1182,7 @@
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET 30    // (mm) An inset for corner leveling
@@ -1219,8 +1224,8 @@
 #endif
 
 // Homing speeds (mm/m)
-#define HOMING_FEEDRATE_XY (50*60)
-#define HOMING_FEEDRATE_Z  (4*60)
+#define HOMING_FEEDRATE_XY (100*60)
+#define HOMING_FEEDRATE_Z  (16*60)
 
 // Validate that endstops are triggered on homing moves
 #define VALIDATE_HOMING_ENDSTOPS
@@ -1792,7 +1797,7 @@
 //
 // LCD for Melzi Card with Graphical LCD
 //
-//#define LCD_FOR_MELZI
+#define LCD_FOR_MELZI
 
 //
 // SSD1306 OLED full graphics generic display
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index f967e3af8..98a2db0d5 100644
--- Marlin/Configuration_adv.h
+++ Marlin/Configuration_adv.h
@@ -74,8 +74,8 @@
  * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
-  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_PERIOD 70        // Seconds
+  #define THERMAL_PROTECTION_HYSTERESIS 10    // Degrees Celsius
 
   /**
    * Whenever an M104, M109, or M303 increases the target temperature, the
@@ -329,7 +329,7 @@
   #endif
 #endif
 
-//#define Z_DUAL_STEPPER_DRIVERS
+#define Z_DUAL_STEPPER_DRIVERS
 #if ENABLED(Z_DUAL_STEPPER_DRIVERS)
   //#define Z_DUAL_ENDSTOPS
   #if ENABLED(Z_DUAL_ENDSTOPS)
@@ -459,7 +459,7 @@
 // @section lcd
 
 #if ENABLED(ULTIPANEL)
-  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 10*60} // Feedrates for manual moves along X, Y, Z, E from panel
   #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions
   #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif
@@ -562,7 +562,7 @@
 //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 }    // Default drive percent - X, Y, Z, E axis
 
 // Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro)
-//#define DIGIPOT_I2C
+#define DIGIPOT_I2C
 #if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A)
   /**
    * Common slave addresses:
@@ -578,10 +578,11 @@
 #endif
 
 //#define DIGIPOT_MCP4018          // Requires library from https://github.com/stawel/SlowSoftI2CMaster
-#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4     AZTEEG_X3_PRO: 8     MKS SBASE: 5
+#define DIGIPOT_I2C_NUM_CHANNELS 5 // 5DPRINT: 4     AZTEEG_X3_PRO: 8     MKS SBASE: 5
 // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
 // These correspond to the physical drivers, so be mindful if the order is changed.
-#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 }  //  AZTEEG_X3_PRO
+// #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 }  //  AZTEEG_X3_PRO
+#define DIGIPOT_I2C_MOTOR_CURRENTS { 1, 1, 0.7, 1, 0.7 }  //  MKS SBASE: 5
 
 //===========================================================================
 //=============================Additional Features===========================