amlogic remote.conf for using indihome / useetv / telkom remote

indihome_remote.conf

#*********************************************************************************************************
#
#this file is configuration for each factory remote device
# 	work_mode	  0 :software mode  1 :hardware mode
#	repeat_enable	  0 :disable repeat 1 :enable repeat
#
#	factory_code      each device has it's unique factory code.
#			  pattern:custom_code(16bit)+index_code(16bit)
#			  examble: 0xff000001 = 0xff00(custom cod)  0001 (index)
#
#	release_delay	  unit:ms.release will report from kernel to user layer after this period of time
#			  from press or repeat triggered.
#
#	debug_enable      0 :debug disable  1 :debug disable
#
# SW MODE:
#	bit_count	  how many bits in each frame
#	tw_leader_act	  time window for leader active
#	tw_bit0		  time window for bit0 time.
#	tw_bit1		  time window for bit1 time
#	tw_repeat_leader  time window for repeat leader
# REG
#	reg_base_gen	  set value for PREG_IR_DEC_BASE_GEN
#	reg_control	  set value for PREG_IR_DEC_CONTROL
#	reg_leader_act	  set value for PREG_IR_DEC_LEADER_ACTIVE
#	reg_leader_idle	  set value for PREG_IR_DEC_LEADER_IDLE
#	reg_repeat_leader set value for PREG_IR_DEC_REPEAT_IDLE
#	reg_bit0_time	  set value for PREG_IR_DEC_BIT0_TIME
#*************************************************************************************************************
#amlogic NEC remote
work_mode  		= 0
repeat_enable = 1
repeat_delay = 130
repeat_peroid = 120
release_delay   =       20
debug_enable 	= 1


custom_begin
		factory_infcode = 0
		factory_code	= 0x40400001
    key_begin
      0x47 113 #mute
      
      #0x07 #Live / F1
      #0x02 #VOD / F3
      #0x0c #Service / F4
      
      0x04 102 #app
      0x08 1   #back
      
      0x45 128 #stop
      0x09 115 #Vol +
      0x1a 112 #|<<
      0x1e 103 #Ch +
      0x57 114 #Vol -
      0x18 123 #>>|
      
      0x42 6 #5
      0x0b 7 #6
      0x1f 9 #8
      #0x0e  #switch/jump
    key_end
    
    repeat_key_begin
    repeat_key_end
    
custom_end

custom_begin
		factory_infcode = 1
		factory_code	= 0xff000001
    
    fn_key_scancode    = 0x11
    left_key_scancode  = 0x48
    right_key_scancode = 0x4a
    up_key_scancode    = 0x47
    down_key_scancode  = 0x4b
    ok_key_scancode    = 0x49

    mouse_begin
        0 0x48
        1 0x4a
        2 0x47
        3 0x4b
    mouse_end
    
    key_begin
      0x40 116 #power
      #0x1c #L/R
      0x1d 150 #SET / Setting
      #0x11 #LOC
      
      #0x0f #TVOD / F2
      
      0x4d 139 #menu
      0x47 103 #up
      0x48 105 #kiri
      0x49 28  #enter
      0x4a 106 #kanan
      0x4b 108 #bawah
      #0x1e   #info
      
      0x43 121 #<<
      0x46 120 #>>
      0x44 119 #|
      0x15 108 #Ch -
      
      0x01 2 #1
      0x02 3 #2
      0x03 4 #3
      0x04 5 #4
      0x07 8 #7
      0x09 10 #9
      #0x0a  #-/--
      0x00 11 #0
    key_end
    
    repeat_key_begin  
    repeat_key_end
custom_end