Skip to content

Instantly share code, notes, and snippets.

@pinuke

pinuke/serial.log

Created November 20, 2022 03:14
Show Gist options
  • Save pinuke/d99b047edde566f91502c9db8c41abc4 to your computer and use it in GitHub Desktop.
Save pinuke/d99b047edde566f91502c9db8c41abc4 to your computer and use it in GitHub Desktop.
Download ZIP
Rock Pi 4 stuck during boot up
Raw
serial.log
In
channel 0
CS = 0
MR0=0x19
MR4=0x3
MR5=0x6
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 1
CS = 0
MR0=0x19
MR4=0x3
MR5=0x6
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 0 training pass!
channel 1 training pass!
change freq to 416MHz 0,1
Channel 0: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
256B stride
channel 0
CS = 0
MR0=0x19
MR4=0x3
MR5=0x6
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 1
CS = 0
MR0=0x19
MR4=0x3
MR5=0x6
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 0 training pass!
channel 1 training pass!
channel 0, cs 0, advanced training done
channel 1, cs 0, advanced training done
change freq to 666MHz 1,0
ch 0 ddrconfig = 0x101, ddrsize = 0x40
ch 1 ddrconfig = 0x101, ddrsize = 0x40
pmugrf_os_reg[2] = 0x32C1F2C1, stride = 0xD
ddr_set_rate to 328MHZ
ddr_set_rate to 666MHZ
ddr_set_rate to 416MHZ, ctl_index 0
ddr_set_rate to 666MHZ, ctl_index 1
support 416 328 666 MHz, current 666MHz
OUT
Boot1: 2019-03-14, version: 1.19
CPUId = 0x0
ChipType = 0x10, 267
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
emmc reinit
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
emmc reinit
mmc: ERROR: SDHCI ERR:cmd:0x102,stat:0x18000
mmc: ERROR: Card did not respond to voltage select!
SdmmcInit=2 1
mmc0:cmd5,20
SdmmcInit=0 0
BootCapSize=0
UserCapSize=60874MB
FwPartOffset=2000 , 0
StorageInit ok = 45441
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT part: 0, name: loader1, start:0x40, size:0x1f40
GPT part: 1, name: loader2, start:0x4000, size:0x2000
GPT part: 2, name: trust, start:0x6000, size:0x2000
GPT part: 3, name: boot, start:0x8000, size:0x100000
GPT part: 4, name: rootfs, start:0x108000, size:0x66b573
no find partition:uboot.
LoadTrust Addr:0x4000
No find bl30.bin
No find bl32.bin
Load uboot, ReadLba = 2000
hdr 0000000003380880 + 0x0:0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0
0,0x00,0x00,0x00,0x00,0x00,
Load OK, addr=0x200000, size=0xf14cc
RunBL31 0x40000
NOTICE: BL31: v1.3(release):845ee93
NOTICE: BL31: Built : 15:51:11, Jul 22 2020
NOTICE: BL31: Rockchip release version: v1.1
INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: plat_rockchip_pmu_init(1196): pd status 3e
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE init
ialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-00028-g8e67d58161 (Oct 19 2022 - 10:11:41 +0800)
Model: Radxa ROCK 4C+
PreSerial: 2
DRAM: 3.9 GiB
Relocation Offset is: f5bdd000
Sysmem: init
I2c speed: 400000Hz
PMIC: RK8090 (on=0x69, off=0x02)
vdd_log 900000 uV
vdd_cpu_l 900000 uV
MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0
Using default environment
Failed to found available display route
Failed to found available display route
Model: Radxa ROCK 4C+
Bootdev(atags): mmc 1
PartType: EFI
get part misc fail -1
boot mode: None
CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
CLK: (uboot. armb: enter 24000 KHz, init 24000 KHz, kernel 0N/A)
aplll 816000 KHz
apllb 24000 KHz
dpll 666000 KHz
cpll 24000 KHz
gpll 800000 KHz
npll 600000 KHz
vpll 24000 KHz
aclk_perihp 133333 KHz
hclk_perihp 66666 KHz
pclk_perihp 33333 KHz
aclk_perilp0 266666 KHz
hclk_perilp0 88888 KHz
pclk_perilp0 44444 KHz
hclk_perilp1 100000 KHz
pclk_perilp1 50000 KHz
Net: eth0: ethernet@fe300000
Hit key to stop autoboot('CTRL+C'): 0
Here trying to boot from nvme
dcache off
Device 0: unknown device
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:4...
Found /extlinux/extlinux.conf
pxefile_addr_str = 0x00500000
bootfile = /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
reading /extlinux/extlinux.conf
449 bytes read in 5 ms (86.9 KiB/s)
Retrieving file: /hw_intfc.conf
reading /hw_intfc.conf
2277 bytes read in 4 ms (555.7 KiB/s)
hw_parse_property: illegal line
hw_parse_property: illegal line
dtoverlay number: 0, name:/overlays/console-on-ttyS2.dtbo
hw_conf.valid = 1
hw_conf.pwm0 = 0
hw_conf.pwm1 = 0
hw_conf.uart2 = 0
hw_conf.uart4 = 0
hw_conf.spi1 = 0
hw_conf.spi2 = 0
hw_conf.i2c2 = 0
hw_conf.i2c6 = 0
hw_conf.i2c7 = 0
hw_conf.dts_overlay_count = 1
hw_conf.dts_overlay[0] = /overlays/console-on-ttyS2.dtbo
1: kernel-4.4.194-11-rk3399-rockchip-g1bb08d49cc40
Retrieving file: /initrd.img-4.4.194-11-rk3399-rockchip-g1bb08d49cc40
reading /initrd.img-4.4.194-11-rk3399-rockchip-g1bb08d49cc40
19582211 bytes read in 838 ms (22.3 MiB/s)
Retrieving file: /vmlinuz-4.4.194-11-rk3399-rockchip-g1bb08d49cc40
reading /vmlinuz-4.4.194-11-rk3399-rockchip-g1bb08d49cc40
16756744 bytes read in 717 ms (22.3 MiB/s)
append: earlyprintk console=ttyFIQ0,1500000n8 rw init=/sbin/init rootfstype=ext4
rootwait root=UUID=36c6d71f-716f-4efa-8dab-18225508dac2 console=ttyS2,1500000n
8
Retrieving file: /dtbs/4.4.194-11-rk3399-rockchip-g1bb08d49cc40/rockchip/rk3399-
rock-4c-plus.dtb
reading /dtbs/4.4.194-11-rk3399-rockchip-g1bb08d49cc40/rockchip/rk3399-rock-4c-p
lus.dtb
101509 bytes read in 22 ms (4.4 MiB/s)
fdt addr 0000000008300000
fdt magic number edfe0dd0
fdt size 1048576
merge_dts_overlay
Retrieving file: /overlays/console-on-ttyS2.dtbo
reading /overlays/console-on-ttyS2.dtbo
774 bytes read in 6 ms (126 KiB/s)
overlay dtb(0x0000000008200000) is valid
fdt_overlay_apply 0000000008300000 0000000008200000
## Flattened Device Tree blob at 08300000
Booting using the fdt blob at 0x8300000
'reserved-memory' ramoops@110000: addr=110000 size=f0000
Loading Ramdisk to e8b16000, end e9dc2d03 ... OK
Loading Device Tree to 00000000e8a13000, end 00000000e8b15fff ... OK
Adding bank: 0x00200000 - 0xf8000000 (size: 0xf7e00000)
Total: 10895.713 ms
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.194-11-rk3399-rockchip-g1bb08d49cc40 (stephen@m
rs-ella) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfb
c167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #1 SMP Fri Nov 4 21:33:40
CST 2022
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@0000
0000': base 0x0000000000000000, size 0 MiB
[ 0.000000] cma: Reserved 16 MiB at 0x00000000f7000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0f6ed1000 s45928 r8192 d318
96 u86016
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 999432
[ 0.000000] Kernel command line: earlyprintk console=ttyFIQ0,1500000n8 rw ini
t=/sbin/init rootfstype=ext4 rootwait root=UUID=36c6d71f-716f-4efa-8dab-1822550
8dac2 console=ttyS2,1500000n8
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes
)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] software IO TLB: mapped [mem 0xee600000-0xf2600000] (64MB)
[ 0.000000] Memory: 3869644K/4061184K available (9790K kernel code, 1516K rwd
ata, 3996K rodata, 1024K init, 661K bss, 175156K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 M
B)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 G
B)
[ 0.000000] .init : 0xffffff8008e00000 - 0xffffff8008f00000 ( 1024 K
B)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008a10000 ( 9792 K
B)
[ 0.000000] .rodata : 0xffffff8008a10000 - 0xffffff8008e00000 ( 4032 K
B)
[ 0.000000] .data : 0xffffff8008f00000 - 0xffffff800907b008 ( 1517 K
B)
[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 G
B maximum)
[ 0.000000] 0xffffffbdc0008000 - 0xffffffbdc3e00000 ( 61 M
B actual)
[ 0.000000] fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 K
B)
[ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 M
B)
[ 0.000000] memory : 0xffffffc000200000 - 0xffffffc0f8000000 ( 3966 M
B)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
[ 0.000000] ITS: allocated 65536 Devices @ee000000 (psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x00000000ee080000
[ 0.000000] ITS: Allocated 1792 chunks for LPIs
[ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
[ 0.000000] CPU0: using LPI pending table @0x00000000ee090000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpu
s/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /c
pus/cpu@101[5] }
[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac
as parent of dclk_vop0, rate changes may not work
[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac
as parent of dclk_vop1, rate changes may not work
[ 0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles:
0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980
46511097ns
[ 0.001458] Console: colour dummy device 80x25
[ 0.001486] Calibrating delay loop (skipped), value calculated using timer fr
equency.. 48.00 BogoMIPS (lpj=24000)
[ 0.001499] pid_max: default: 32768 minimum: 301
[ 0.001661] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.001673] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.002445] Initializing cgroup subsys memory
[ 0.002480] Initializing cgroup subsys devices
[ 0.002493] Initializing cgroup subsys freezer
[ 0.002510] Initializing cgroup subsys net_cls
[ 0.002522] Initializing cgroup subsys perf_event
[ 0.002536] Initializing cgroup subsys pids
[ 0.002582] ftrace: allocating 36819 entries in 144 pages
[ 0.092534] sched-energy: Sched-energy-costs installed from DT
[ 0.092551] CPU0: update cpu_capacity 401
[ 0.092612] ASID allocator initialised with 32768 entries
[ 0.095107] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee2
0000 domain created
[ 0.095636] Platform MSI: /interrupt-controller@fee00000/interrupt-controller
@fee20000 domain created
[ 0.097048] Detected VIPT I-cache on CPU1
[ 0.097085] CPU1: found redistributor 1 region 0:0x00000000fef20000
[ 0.097115] CPU1: using LPI pending table @0x00000000ee290000
[ 0.097173] CPU1: update cpu_capacity 401
[ 0.097177] CPU1: Booted secondary processor [410fd034]
[ 0.097970] Detected VIPT I-cache on CPU2
[ 0.098002] CPU2: found redistributor 2 region 0:0x00000000fef40000
[ 0.098033] CPU2: using LPI pending table @0x00000000ee2c0000
[ 0.098085] CPU2: update cpu_capacity 401
[ 0.098089] CPU2: Booted secondary processor [410fd034]
[ 0.098882] Detected VIPT I-cache on CPU3
[ 0.098913] CPU3: found redistributor 3 region 0:0x00000000fef60000
[ 0.098943] CPU3: using LPI pending table @0x00000000ee320000
[ 0.098993] CPU3: update cpu_capacity 401
[ 0.098997] CPU3: Booted secondary processor [410fd034]
[ 0.099783] Detected PIPT I-cache on CPU4
[ 0.099806] CPU4: found redistributor 100 region 0:0x00000000fef80000
[ 0.099841] CPU4: using LPI pending table @0x00000000ee350000
[ 0.099876] CPU4: update cpu_capacity 1024
[ 0.099879] CPU4: Booted secondary processor [410fd082]
[ 0.100528] Detected PIPT I-cache on CPU5
[ 0.100551] CPU5: found redistributor 101 region 0:0x00000000fefa0000
[ 0.100588] CPU5: using LPI pending table @0x00000000ee380000
[ 0.100622] CPU5: update cpu_capacity 1024
[ 0.100626] CPU5: Booted secondary processor [410fd082]
[ 0.100740] Brought up 6 CPUs
[ 0.100823] SMP: Total of 6 processors activated.
[ 0.100832] CPU features: detected feature: GIC system register CPU interface
[ 0.100842] CPU features: detected feature: 32-bit EL0 Support
[ 0.100853] CPU: All CPU(s) started at EL2
[ 0.100899] alternatives: patching kernel code
[ 0.102258] devtmpfs: initialized
[ 0.125854] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma
x_idle_ns: 1911260446275000 ns
[ 0.125877] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.126605] pinctrl core: initialized pinctrl subsystem
[ 0.128297] Failed to find legacy iommu devices
[ 0.128698] NET: Registered protocol family 16
[ 0.133603] cpuidle: using governor ladder
[ 0.137610] cpuidle: using governor menu
[ 0.137635] Registered FIQ tty driver
[ 0.137821] vdso: 2 pages (1 code @ ffffff8008a16000, 1 data @ ffffff8008f040
00)
[ 0.137853] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.138639] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.160875] console [pstore-1] enabled
[ 0.160884] pstore: Registered ramoops as persistent store backend
[ 0.160893] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[ 0.228490] console [ttyFIQ0] enabled
[ 0.229033] Registered fiq debugger ttyFIQ0
[ 0.243314] vbus_host: regulator get failed, ret=-517
[ 0.244021] vbus_typec: supplied by vcc5v0_sys
[ 0.245089] vcc3v3_pcie: supplied by vcc5v0_sys
[ 0.246311] iommu: Adding device ff650000.vpu_service to group 0
[ 0.246931] iommu: Adding device ff660000.rkvdec to group 1
[ 0.247534] iommu: Adding device ff8f0000.vop to group 2
[ 0.248110] iommu: Adding device ff900000.vop to group 3
[ 0.248672] iommu: Adding device ff910000.rkisp1 to group 4
[ 0.249643] rk_iommu ff650800.iommu: can't get sclk
[ 0.250337] rk_iommu ff660480.iommu: can't get sclk
[ 0.250958] rk_iommu ff8f3f00.iommu: can't get sclk
[ 0.251561] rk_iommu ff903f00.iommu: can't get sclk
[ 0.252150] rk_iommu ff914000.iommu: can't get sclk
[ 0.252751] rk_iommu ff924000.iommu: can't get sclk
[ 0.253551] SCSI subsystem initialized
[ 0.254080] usbcore: registered new interface driver usbfs
[ 0.254606] usbcore: registered new interface driver hub
[ 0.255168] usbcore: registered new device driver usb
[ 0.255683] media: Linux media interface: v0.10
[ 0.256133] Linux video capture interface: v2.00
[ 0.256626] pps_core: LinuxPPS API ver. 1 registered
[ 0.257068] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome
tti <giometti@linux.it>
[ 0.257899] PTP clock support registered
[ 0.259336] Advanced Linux Sound Architecture Driver Initialized.
[ 0.260997] rockchip-cpuinfo cpuinfo: Serial : 550f39de1ea9c0e8
[ 0.262007] clocksource: Switched to clocksource arch_sys_counter
[ 0.317509] thermal thermal_zone1: power_allocator: sustainable_power will be
estimated
[ 0.318445] NET: Registered protocol family 2
[ 0.319303] TCP established hash table entries: 32768 (order: 6, 262144 bytes
)
[ 0.320209] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
[ 0.321619] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.322332] UDP hash table entries: 2048 (order: 5, 196608 bytes)
[ 0.323065] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
[ 0.324077] NET: Registered protocol family 1
[ 0.324768] RPC: Registered named UNIX socket transport module.
[ 0.325308] RPC: Registered udp transport module.
[ 0.325728] RPC: Registered tcp transport module.
[ 0.326155] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.327695] Trying to unpack rootfs image as initramfs...
[ 1.266829] Freeing initrd memory: 19120K
[ 1.267597] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counte
rs available
[ 1.268414] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counte
rs available
[ 1.272311] Initialise system trusted keyring
[ 1.279804] VFS: Disk quotas dquot_6.6.0
[ 1.280331] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.283210] NFS: Registering the id_resolver key type
[ 1.283685] Key type id_resolver registered
[ 1.284071] Key type id_legacy registered
[ 1.284450] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.289705] NET: Registered protocol family 38
[ 1.290131] Key type asymmetric registered
[ 1.290498] Asymmetric key parser 'x509' registered
[ 1.291107] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2
46)
[ 1.291762] io scheduler noop registered
[ 1.292128] io scheduler deadline registered
[ 1.292736] io scheduler cfq registered (default)
[ 1.294290] rockchip-usb2phy ff770000.syscon:usb2-phy@e450: failed to create
phy
[ 1.295396] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: failed to create
phy
[ 1.301661] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
[ 1.302274] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[ 1.302866] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[ 1.303443] rockchip-pcie f8000000.pcie: missing "memory-region" property
[ 1.304060] PCI host bridge /pcie@f8000000 ranges:
[ 1.304503] MEM 0xfa000000..0xfbdfffff -> 0xfa000000
[ 1.304961] IO 0xfbe00000..0xfbefffff -> 0xfbe00000
[ 1.847070] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
[ 1.847685] rockchip-pcie f8000000.pcie: deferred probe failed
[ 1.848474] rockchip-pcie: probe of f8000000.pcie failed with error -110
[ 1.849919] Module initialized.
[ 1.850670] rk-vcodec ff650000.vpu_service: no regulator for vcodec
[ 1.851533] rk-vcodec ff650000.vpu_service: probe device
[ 1.852260] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled
[ 1.853386] rk-vcodec ff650000.vpu_service: could not find power_model node
[ 1.854020] rk-vcodec ff650000.vpu_service: init success
[ 1.854735] rk-vcodec ff660000.rkvdec: no regulator for vcodec
[ 1.855705] rk-vcodec ff660000.rkvdec: probe device
[ 1.856360] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled
[ 1.857320] rk-vcodec ff660000.rkvdec: could not find power_model node
[ 1.857903] rk-vcodec ff660000.rkvdec: init success
[ 1.860051] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-2
41330
[ 1.860727] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chan
s-6 Num_Peri-12 Num_Events-12
[ 1.863035] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-2
41330
[ 1.863710] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Cha
ns-8 Num_Peri-20 Num_Events-16
[ 1.865573] rockchip-system-monitor rockchip-system-monitor: system monitor p
robe
[ 1.866952] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[ 1.868182] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 35, base_baud =
1500000) is a 16550A
[ 1.870034] [drm] Initialized drm 1.1.0 20060810
[ 1.874307] [drm] Rockchip DRM driver version: v1.0.1
[ 1.876764] mali ff9a0000.gpu: Failed to get regulator
[ 1.877232] mali ff9a0000.gpu: Power control initialization failed
[ 1.878136] Unable to detect cache hierarchy for CPU 0
[ 1.879333] brd: module loaded
[ 1.884787] loop: module loaded
[ 1.885634] zram: Added device: zram0
[ 1.886263] lkdtm: No crash points registered, enable through debugfs
[ 1.889027] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[ 1.889657] rk_gmac-dwmac fe300000.ethernet: TX delay(0x2a).
[ 1.890174] rk_gmac-dwmac fe300000.ethernet: RX delay(0x21).
[ 1.890691] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[ 1.891418] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[ 1.892043] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[ 1.897595] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[ 1.898221] stmmac - user ID: 0x10, Synopsys ID: 0x35
[ 1.898674] Ring mode enabled
[ 1.898956] DMA HW capability register supported
[ 1.899372] Normal descriptors
[ 1.899680] RX Checksum Offload Engine supported (type 2)
[ 1.900174] TX Checksum insertion supported
[ 1.900557] Wake-Up On Lan supported
[ 1.900917] Enable RX Mitigation via HW Watchdog Timer
[ 2.039176] libphy: stmmac: probed
[ 2.039492] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.040070] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01)
[ 2.042057] Rockchip WiFi SYS interface (V1.00) ...
[ 2.042640] usbcore: registered new interface driver asix
[ 2.043196] usbcore: registered new interface driver cdc_ether
[ 2.043764] usbcore: registered new interface driver rndis_host
[ 2.044388] usbcore: registered new interface driver cdc_ncm
[ 2.046893] rockchip-dwc3 usb0: failed to get drvdata dwc3
[ 2.048975] rockchip-dwc3 usb1: failed to get drvdata dwc3
[ 2.050572] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.051240] ehci-pci: EHCI PCI platform driver
[ 2.051705] ehci-platform: EHCI generic platform driver
[ 2.053104] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.053672] ohci-platform: OHCI generic platform driver
[ 2.055236] usbcore: registered new interface driver usb-storage
[ 2.057313] i2c /dev entries driver
[ 2.058854] rk808 0-0020: Pmic Chip id: 0x8090
[ 2.059589] rk808 0-0020: source: on=0x40, off=0x00
[ 2.060811] rk808 0-0020: support dcdc3 fb mode:-22, -377421824
[ 2.061601] rk808 0-0020: support pmic reset mode:0,0
[ 2.064955] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 2.065604] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 2.066257] DCDC_REG1: supplied by vcc5v0_sys
[ 2.068151] DCDC_REG2: supplied by vcc5v0_sys
[ 2.070131] DCDC_REG3: supplied by vcc5v0_sys
[ 2.071819] DCDC_REG4: supplied by vcc5v0_sys
[ 2.073523] DCDC_REG5: supplied by vcc5v0_sys
[ 2.075033] LDO_REG1: supplied by vcc_buck5
[ 2.077210] LDO_REG2: supplied by vcc_buck5
[ 2.079387] LDO_REG3: supplied by vcc_buck5
[ 2.081564] LDO_REG4: supplied by vcc_buck5
[ 2.083725] LDO_REG5: supplied by vcc_buck5
[ 2.084570] vcc_mipi: Bringing 1500000uV into 3000000-3000000uV
[ 2.087141] LDO_REG6: supplied by vcc_buck5
[ 2.089362] LDO_REG7: supplied by vcc5v0_sys
[ 2.091432] LDO_REG8: supplied by vcc5v0_sys
[ 2.093627] LDO_REG9: supplied by vcc5v0_sys
[ 2.095719] SWITCH_REG1: supplied by vcc5v0_sys
[ 2.096511] vbus_host: supplied by vcc5v0_usb2.0
[ 2.097425] SWITCH_REG2: supplied by vcc3v3_sys
[ 2.099023] rk817-battery rk817-battery: Failed to find matching dt id
[ 2.099767] rk817-charger rk817-charger: Failed to find matching dt id
[ 2.102488] input: rk8xx_pwrkey as /devices/platform/ff3c0000.i2c/i2c-0/0-002
0/input/input0
[ 2.106906] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[ 2.109422] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
[ 2.110097] fan53555-reg: supplied by vcc5v0_sys
[ 2.112824] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected!
[ 2.113493] fan53555-reg: supplied by vcc5v0_sys
[ 2.115992] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80091b
e000
[ 2.117972] IR NEC protocol handler initialized
[ 2.119196] rkisp1 ff910000.rkisp1: rkisp1 driver version: v00.01.05
[ 2.119785] rkisp1 ff910000.rkisp1: Missing rockchip,grf property
[ 2.121894] usbcore: registered new interface driver npu_acm
[ 2.122468] usbcore: registered new interface driver uvcvideo
[ 2.122978] USB Video Class driver (1.1.1)
[ 2.126656] Boot mode: normal
[ 2.127965] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, tem
perature=2147483647
[ 2.128925] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
[ 2.130116] dw_wdt ff848000.watchdog: Should better to setup a 'resets' prope
rty in dt, that must been named with reset
[ 2.131742] cpu cpu0: bin=2
[ 2.132076] cpu cpu0: leakage=0
[ 2.145146] cpu cpu0: temp=35625, pvtm=136773 (137463 + -690)
[ 2.146653] cpu cpu0: pvtm-volt-sel=0
[ 2.147057] cpu cpu0: bin-scale=46
[ 2.147368] cpu cpu0: bin-volt-sel=20
[ 2.147979] cpu cpu4: bin=2
[ 2.148336] cpu cpu4: leakage=0
[ 2.160805] cpu cpu4: temp=35625, pvtm=148833 (149259 + -426)
[ 2.161480] cpu cpu4: pvtm-volt-sel=0
[ 2.161852] cpu cpu4: bin-scale=30
[ 2.162201] cpu cpu4: bin-volt-sel=20
[ 2.163922] cpu cpu0: avs=0
[ 2.164218] cpu cpu0: scale_rate=1008000000
[ 2.164845] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=
0
[ 2.166329] cpu cpu0: failed to find power_model node
[ 2.167784] cpu cpu4: avs=0
[ 2.168073] cpu cpu4: scale_rate=1512000000
[ 2.168696] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=
0
[ 2.170500] cpu cpu4: failed to find power_model node
[ 2.171803] sdhci: Secure Digital Host Controller Interface driver
[ 2.172386] sdhci: Copyright(c) Pierre Ossman
[ 2.172778] Synopsys Designware Multimedia Card Interface Driver
[ 2.174197] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode
.
[ 2.175167] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[ 2.175786] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[ 2.176413] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit
host data width,256 deep fifo
[ 2.177415] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[ 2.177964] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[ 2.179662] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode
.
[ 2.180348] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[ 2.180958] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[ 2.181511] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit
host data width,256 deep fifo
[ 2.182711] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found
[ 2.184574] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000
done
[ 2.185647] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000
done
[ 2.199044] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz,
actual 400000HZ div = 0)
[ 2.212591] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
[ 2.213468] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.215705] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[ 2.216246] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
[ 2.247223] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using A
DMA
[ 2.247428] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000
Hz, actual 50000000HZ div = 0)
[ 2.247779] mmc0: new high speed SDXC card at address 59b4
[ 2.250069] mmcblk0: mmc0:59b4 SK64G 59.4 GiB
[ 2.250917] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.251593] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.252447] usbcore: registered new interface driver usbhid
[ 2.252949] usbhid: USB HID core driver
[ 2.254208] rockchip-dmc dmc: Cannot get the regulator "center"
[ 2.255421] extcon-pd-virtual virtual-pd0: vpd_extcon_probe: 376 start
[ 2.256985] extcon-pd-virtual virtual-pd0: vpd_extcon_probe: 507 success
[ 2.260929] GPT:Primary header thinks Alt. header is not at the end of the di
sk.
[ 2.261038] usbcore: registered new interface driver snd-usb-audio
[ 2.262202] GPT:7812499 != 124669951
[ 2.262526] GPT:Alternate GPT header not at the end of the disk.
[ 2.263062] GPT:7812499 != 124669951
[ 2.263386] GPT: Use GNU Parted to correct GPT errors.
[ 2.263867] mmcblk0: p1 p2 p3 p4 p5
[ 2.265802] Initializing XFRM netlink socket
[ 2.266217] NET: Registered protocol family 17
[ 2.266670] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 2.267259] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 2.267708] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6256
[ 2.268327] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 2.268960] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gp
io.
[ 2.269680] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wa
ke_irq = 3, flags = 0.
[ 2.270489] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found
!
[ 2.271140] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 2.271604] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 2.272068] [BT_RFKILL]: Enter rfkill_rk_init
[ 2.272765] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_
gpios = 83.
[ 2.273521] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_
gpio = 9.
[ 2.274249] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_g
pio = 91.
[ 2.274970] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_h
ost_irq = 4.
[ 2.276064] [BT_RFKILL]: Request irq for bt wakeup host
[ 2.276571] [BT_RFKILL]: ** disable irq
[ 2.277075] [BT_RFKILL]: bt_default device registered.
[ 2.277597] Key type dns_resolver registered
[ 2.278659] Registered cp15_barrier emulation handler
[ 2.279217] Registered setend emulation handler
[ 2.281642] registered taskstats version 1
[ 2.282067] Loading compiled-in X.509 certificates
[ 2.283463] rga2: Driver loaded successfully ver:3.2.18218
[ 2.284118] rga2: Module initialized.
[ 2.285899] phy phy-ff770000.syscon:usb2-phy@e450.5: Failed to get VBUS suppl
y regulator
[ 2.288042] phy phy-ff770000.syscon:usb2-phy@e460.7: Failed to get VBUS suppl
y regulator
[ 2.290568] rockchip-drm display-subsystem: defer getting devfreq
[ 2.291475] rockchip-vop ff900000.vop: missing rockchip,grf property
[ 2.292397] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8
008ab7368)
[ 2.293161] rockchip-vop ff8f0000.vop: missing rockchip,grf property
[ 2.293944] rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8
008ab7368)
[ 2.295294] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports
[ 2.295914] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus
driver
[ 2.296749] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a
with HDCP (DWC HDMI 2.0 TX PHY)
[ 2.300034] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff
8008aab878)
[ 2.302240] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports
[ 2.303935] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff80
08aac8f0)
[ 2.304707] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.305347] [drm] No driver support for vblank timestamp query.
[ 2.306188] rockchip-drm display-subsystem: failed to parse loader memory
[ 2.306843] rockchip-drm display-subsystem: No connectors reported connected
with modes
[ 2.307632] [drm] Cannot find any crtc or sizes - going 1024x768
[ 2.323895] Console: switching to colour frame buffer device 128x48
[ 2.336146] rockchip-drm display-subsystem: fb0: frame buffer device
[ 2.343044] mali ff9a0000.gpu: bin=2
[ 2.343417] mali ff9a0000.gpu: leakage=0
[ 2.356987] mali ff9a0000.gpu: temp=36250, pvtm=116120 (116350 + -230)
[ 2.359618] mali ff9a0000.gpu: pvtm-volt-sel=0
[ 2.360107] mali ff9a0000.gpu: bin-scale=61
[ 2.360485] mali ff9a0000.gpu: bin-volt-sel=20
[ 2.361570] mali ff9a0000.gpu: avs=0
[ 2.361921] mali ff9a0000.gpu: scale_rate=600000000
[ 2.363085] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
[ 2.364041] mali ff9a0000.gpu: Protected mode not available
[ 2.365204] mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
h_table=0
[ 2.365987] mali ff9a0000.gpu: Using configured power model mali-simple-power
-model, and fallback mali-simple-power-model
[ 2.367162] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfr
eq.c; [Line] : 423; [Func] : kbase_devfreq_init(); success initing power_model_s
imple.
[ 2.369463] mali ff9a0000.gpu: Probed as mali0
[ 2.376137] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[ 2.376647] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus nu
mber 1
[ 2.377593] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110
quirks 0x06030010
[ 2.380471] xhci-hcd xhci-hcd.9.auto: irq 225, io mem 0xfe800000
[ 2.381285] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.381886] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.382543] usb usb1: Product: xHCI Host Controller
[ 2.382984] usb usb1: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 xhci-hcd
[ 2.383728] usb usb1: SerialNumber: xhci-hcd.9.auto
[ 2.384750] hub 1-0:1.0: USB hub found
[ 2.385161] hub 1-0:1.0: 1 port detected
[ 2.385885] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[ 2.386407] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus nu
mber 2
[ 2.387176] usb usb2: We don't know the algorithms for LPM for this host, dis
abling LPM.
[ 2.387990] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.388604] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.389258] usb usb2: Product: xHCI Host Controller
[ 2.389699] usb usb2: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 xhci-hcd
[ 2.390443] usb usb2: SerialNumber: xhci-hcd.9.auto
[ 2.391414] hub 2-0:1.0: USB hub found
[ 2.391775] hub 2-0:1.0: 1 port detected
[ 2.392707] xhci-hcd xhci-hcd.9.auto: remove, state 1
[ 2.393200] usb usb2: USB disconnect, device number 1
[ 2.394129] xhci-hcd xhci-hcd.9.auto: USB bus 2 deregistered
[ 2.394650] xhci-hcd xhci-hcd.9.auto: remove, state 1
[ 2.395157] usb usb1: USB disconnect, device number 1
[ 2.396640] xhci-hcd xhci-hcd.9.auto: USB bus 1 deregistered
[ 2.397627] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller
[ 2.398166] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus n
umber 1
[ 2.399110] xhci-hcd xhci-hcd.10.auto: hcc params 0x0220fe64 hci version 0x11
0 quirks 0x06030010
[ 2.399926] xhci-hcd xhci-hcd.10.auto: irq 226, io mem 0xfe900000
[ 2.400728] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.401350] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.401985] usb usb1: Product: xHCI Host Controller
[ 2.402438] usb usb1: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 xhci-hcd
[ 2.403183] usb usb1: SerialNumber: xhci-hcd.10.auto
[ 2.404267] hub 1-0:1.0: USB hub found
[ 2.404633] hub 1-0:1.0: 1 port detected
[ 2.405327] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller
[ 2.405833] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus n
umber 2
[ 2.406596] usb usb2: We don't know the algorithms for LPM for this host, dis
abling LPM.
[ 2.407423] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.408034] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.408669] usb usb2: Product: xHCI Host Controller
[ 2.409119] usb usb2: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 xhci-hcd
[ 2.409855] usb usb2: SerialNumber: xhci-hcd.10.auto
[ 2.410784] hub 2-0:1.0: USB hub found
[ 2.411187] hub 2-0:1.0: 1 port detected
[ 2.412930] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[ 2.413510] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus nu
mber 3
[ 2.414507] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110
quirks 0x06030010
[ 2.414804] ehci-platform fe380000.usb: EHCI Host Controller
[ 2.414828] ehci-platform fe380000.usb: new USB bus registered, assigned bus
number 4
[ 2.415047] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000
[ 2.417062] xhci-hcd xhci-hcd.9.auto: irq 225, io mem 0xfe800000
[ 2.417846] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.418502] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.419164] usb usb3: Product: xHCI Host Controller
[ 2.419602] usb usb3: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 xhci-hcd
[ 2.420353] usb usb3: SerialNumber: xhci-hcd.9.auto
[ 2.421097] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[ 2.421512] hub 3-0:1.0: USB hub found
[ 2.421547] hub 3-0:1.0: 1 port detected
[ 2.421907] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[ 2.421922] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus nu
mber 5
[ 2.422053] usb usb5: We don't know the algorithms for LPM for this host, dis
abling LPM.
[ 2.422176] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.422183] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.422189] usb usb5: Product: xHCI Host Controller
[ 2.422195] usb usb5: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 xhci-hcd
[ 2.422200] usb usb5: SerialNumber: xhci-hcd.9.auto
[ 2.422926] hub 5-0:1.0: USB hub found
[ 2.422966] hub 5-0:1.0: 1 port detected
[ 2.423344] rockchip-dwc3 usb0: USB HOST connected
[ 2.428496] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.429143] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.429778] usb usb4: Product: EHCI Host Controller
[ 2.430231] usb usb4: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 ehci_hcd
[ 2.430967] usb usb4: SerialNumber: fe380000.usb
[ 2.431985] hub 4-0:1.0: USB hub found
[ 2.432395] hub 4-0:1.0: 1 port detected
[ 2.435751] ehci-platform fe3c0000.usb: EHCI Host Controller
[ 2.436293] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus
number 6
[ 2.437245] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
[ 2.443191] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[ 2.444055] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.444664] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.445347] usb usb6: Product: EHCI Host Controller
[ 2.445795] usb usb6: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 ehci_hcd
[ 2.446549] usb usb6: SerialNumber: fe3c0000.usb
[ 2.447864] hub 6-0:1.0: USB hub found
[ 2.448240] hub 6-0:1.0: 1 port detected
[ 2.449624] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[ 2.450251] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus
number 7
[ 2.451138] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000
[ 2.506425] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.507052] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.507697] usb usb7: Product: Generic Platform OHCI controller
[ 2.508238] usb usb7: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 ohci_hcd
[ 2.508974] usb usb7: SerialNumber: fe3a0000.usb
[ 2.510104] hub 7-0:1.0: USB hub found
[ 2.510470] hub 7-0:1.0: 1 port detected
[ 2.511886] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[ 2.512520] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus
number 8
[ 2.513406] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
[ 2.568469] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.569096] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 2.569741] usb usb8: Product: Generic Platform OHCI controller
[ 2.570283] usb usb8: Manufacturer: Linux 4.4.194-11-rk3399-rockchip-g1bb08d4
9cc40 ohci_hcd
[ 2.571028] usb usb8: SerialNumber: fe3e0000.usb
[ 2.572235] hub 8-0:1.0: USB hub found
[ 2.572601] hub 8-0:1.0: 1 port detected
[ 2.574567] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode
.
[ 2.575316] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[ 2.575922] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[ 2.576470] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit
host data width,256 deep fifo
[ 2.577454] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[ 2.578019] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[ 2.578985] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
[ 2.592500] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz,
actual 400000HZ div = 0)
[ 2.606308] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
[ 2.613646] asoc-simple-card rk809-sound: rk817-hifi <-> ff880000.i2s mapping
ok
[ 2.614332] asoc-simple-card rk809-sound: ASoC: no source widget found for MI
CBIAS1
[ 2.615023] asoc-simple-card rk809-sound: ASoC: Failed to add route MICBIAS1
-> direct -> Mic Jack
[ 2.615807] asoc-simple-card rk809-sound: ASoC: no sink widget found for IN1P
[ 2.616448] asoc-simple-card rk809-sound: ASoC: Failed to add route Mic Jack
-> direct -> IN1P
[ 2.617215] asoc-simple-card rk809-sound: ASoC: no source widget found for HP
OL
[ 2.617861] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOL -> d
irect -> Headphone Jack
[ 2.618672] asoc-simple-card rk809-sound: ASoC: no source widget found for HP
OR
[ 2.619325] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOR -> d
irect -> Headphone Jack
[ 2.621247] rk-hdmi-dp-sound hdmi-dp-sound: control 3:0:0:ELD:0 is already pr
esent
[ 2.621920] hdmi-audio-codec hdmi-audio-codec.8.auto: ASoC: Failed to add ELD
: -16
[ 2.623050] rk-hdmi-dp-sound hdmi-dp-sound: multicodec <-> ff8a0000.i2s mappi
ng ok
[ 2.623752] hdmi-audio-codec hdmi-audio-codec.8.auto: ASoC: Failed to create
Playback debugfs file
[ 2.625175] =======================================================
[ 2.625731] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
[ 2.626299] =======================================================
[ 2.626853] WiFi driver (Powered by Rockchip,Ver 5.10.WFD.OOB.64bit) init.
[ 2.627715] dhd_module_init in
[ 2.628225] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[ 2.628726] dhd_wlan_init_plat_data, irq = 67Power-up adapter 'DHD generic ad
apter'
[ 2.629485] wifi_platform_set_power = 1
[ 2.629506] rk808-rtc rk808-rtc: setting system clock to 2017-08-04 09:00:15
UTC (1501837215)
[ 2.630593] [WLAN_RFKILL]: rockchip_wifi_power: 1
[ 2.631018] [WLAN_RFKILL]: wifi turn on power. -1
[ 2.644899] rockchip_headset_probe() headset have hook adc mode
[ 2.645656] input: rk-headset as /devices/platform/rk-headset/input/input1
[ 2.647968] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux
.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this m
ali_ko is '', rk_ko_ver is '5', built at '21:30:56', on 'Nov 4 2022'.
[ 2.650299] Mali: Mali device driver loaded
[ 2.650920] rkisp1 ff910000.rkisp1: clear unready subdev num: 1
[ 2.652228] rockchip-mipi-dphy-rx: No link between dphy and sensor
[ 2.652781] rockchip-mipi-dphy-rx: No link between dphy and sensor
[ 2.653347] rkisp1: update sensor failed
[ 2.653437] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
[ 2.654610] ALSA device list:
[ 2.654879] #0: rockchip,rk809-codec
[ 2.654991] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[ 2.655707] #1: rk-hdmi-dp-sound
[ 2.656566] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
[ 2.656578] Freeing unused kernel memory: 1024K
[ 2.660300] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
[ 2.661722] mmc2: queuing unknown CIS tuple 0x81 (1 bytes)
Loading, please wait...
Starting version 247.3-7+deb11u1
[ 2.717607] mmc_host mmc2: Bus speed (slot 0) = 200000000Hz (slot req 2000000
00Hz, actual 200000000HZ div = 0)
[ 2.798032] headset_interrupt:get pin level again,pin=2,i=0
[ 2.832087] wifi_platform_bus_enumerate device present 1
[ 2.832569] mmc2:mmc host rescan start!
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment