Skip to content

Instantly share code, notes, and snippets.

@plntyk

plntyk/screenlog.ath10k.sitecom.wlr8100.log

Created May 13, 2016 09:15
Show Gist options
  • Save plntyk/05fc47bb9c6c9ff54aa84ecdc8175641 to your computer and use it in GitHub Desktop.
Save plntyk/05fc47bb9c6c9ff54aa84ecdc8175641 to your computer and use it in GitHub Desktop.
Download ZIP
Raw
screenlog.ath10k.sitecom.wlr8100.log
U-Boot 0.0.9 (Feb 18 2013 - 14:56:17)
Product Name: WN-AC1600DGR
ap136 - Scorpion 1.0
DRAM:128 MB
Now running in RAM - U-Boot at: 87fc8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
Flash size 16MB, sector count = 256
In: serial
Out: serial
Err: serial
reset_switch:
reset_usb:
Multi Net:
ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ----> S17 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs17_reg_init: SUPPORT_QCA8337
athrs17_reg_init S17_GLOFW_CTRL1_REG624=7f7f7f7f
athrs17_reg_init: MAC0 RGMII
athrs17_reg_init S17_P0PAD_MODE_REG04=87680000
athrs17_reg_init: Not SGMII_FORCED_MODE
athrs17_reg_init S17_PWS_REG10=40000000
athrs17_reg_init S17_P0STATUS_REG7c=7e
athrs17_reg_init QCA8337 ID=1302
athrs17_reg_init: complete
eth0 up
eth0
Setting 0x18116290 to 0x60c0214f
Please choose the operation:
1: Load system code to SDRAM via TFTP.
3: Boot system code via Flash (default).
 1  0
3: System Boot system code via Flash.
athrs17_set_portvlan_isolated complete
## Booting image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-4.1.20
Created: 2016-05-13 7:17:31 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1254143 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.1.20 (tenchi@tenchi-htpc) (gcc version 5.3.0 (LEDE GCC 5.3.0 r222) ) #1 Fri May 13 07:57:05 UTC 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=WLR8100 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),14080k(rootfs),192k(unknown)ro,64k(art)ro,384k(unknown2)ro,15488k@0x40000(firmware) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125404K/131072K available (2800K kernel code, 145K rwdata, 688K rodata, 260K init, 195K bss, 5668K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:240.000MHz, Ref:40.000MHz
[ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000006] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.008274] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.071179] pid_max: default: 32768 minimum: 301
[ 0.076179] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.083219] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092772] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.103681] NET: Registered protocol family 16
[ 0.109425] MIPS: machine is Sitecom WLR-8100
[ 0.556717] registering PCI controller with io_map_base unset
[ 0.562929] registering PCI controller with io_map_base unset
[ 0.575583] PCI host bridge to bus 0000:00
[ 0.579979] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.587288] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.593218] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.600434] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.609285] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x10007fff 64bit]
[ 0.617169] PCI host bridge to bus 0000:01
[ 0.621551] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.628859] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.634789] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.642005] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.650468] pci 0000:01:00.0: invalid calibration data
[ 0.656270] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.664077] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 0.671764] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.677051] pci 0000:01:00.0: using irq 41 for pin 1
[ 0.682944] Switched to clocksource MIPS
[ 0.688162] NET: Registered protocol family 2
[ 0.693533] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.700953] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.707758] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.714592] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.720814] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.727737] NET: Registered protocol family 1
[ 0.733269] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.752723] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.758982] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.771570] io scheduler noop registered
[ 0.775783] io scheduler deadline registered (default)
[ 0.781437] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.788556] console [ttyS0] disabled
[ 0.812415] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.821595] console [ttyS0] enabled
[ 0.821595] console [ttyS0] enabled
[ 0.829014] bootconsole [early0] disabled
[ 0.829014] bootconsole [early0] disabled
[ 0.839517] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.845406] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.850551] 8 cmdlinepart partitions found on MTD device spi0.0
[ 0.856561] Creating 8 MTD partitions on "spi0.0":
[ 0.861419] 0x000000000000-0x000000030000 : "u-boot"
[ 0.867150] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.873192] 0x000000040000-0x0000001a0000 : "kernel"
[ 0.878843] 0x0000001a0000-0x000000f60000 : "rootfs"
[ 0.884507] mtd: device 3 (rootfs) set to be root filesystem
[ 0.890308] 1 squashfs-split partitions found on MTD device rootfs
[ 0.896616] 0x000000a80000-0x000000f60000 : "rootfs_data"
[ 0.902700] 0x000000f60000-0x000000f90000 : "unknown"
[ 0.908486] 0x000000f90000-0x000000fa0000 : "art"
[ 0.913920] 0x000000fa0000-0x000001000000 : "unknown2"
[ 0.919739] 0x000000040000-0x000000f60000 : "firmware"
[ 0.939954] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[ 1.031071] libphy: ag71xx_mdio: probed
[ 1.624446] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.635760] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.224535] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[ 2.232532] NET: Registered protocol family 10
[ 2.240056] NET: Registered protocol family 17
[ 2.244675] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.257591] 8021q: 802.1Q VLAN Support v1.8
[ 2.267058] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.275191] Freeing unused kernel memory: 260K (803ef000 - 80430000)
[ 3.396621] init: Console is alive
[ 3.400228] init: - watchdog -
[ 4.667976] usbcore: registered new interface driver usbfs
[ 4.673655] usbcore: registered new interface driver hub
[ 4.679112] usbcore: registered new device driver usb
[ 4.692639] SCSI subsystem initialized
[ 4.701463] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.709292] ehci-platform: EHCI generic platform driver
[ 4.714701] ehci-platform ehci-platform.0: EHCI Host Controller
[ 4.720736] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 4.731008] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[ 4.737120] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 4.762979] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 4.770200] hub 1-0:1.0: USB hub found
[ 4.774288] hub 1-0:1.0: 1 port detected
[ 4.778550] ehci-platform ehci-platform.1: EHCI Host Controller
[ 4.784616] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 4.794899] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[ 4.801004] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 4.822967] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 4.830195] hub 2-0:1.0: USB hub found
[ 4.834280] hub 2-0:1.0: 1 port detected
[ 4.844161] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 4.849959] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 4.855308] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 3
[ 4.863080] xhci_hcd 0000:00:00.0: hcc params 0x040050af hci version 0x100 quirks 0x00080490
[ 4.872608] hub 3-0:1.0: USB hub found
[ 4.876734] hub 3-0:1.0: 2 ports detected
[ 4.881108] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 4.886466] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 4
[ 4.894112] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.902978] hub 4-0:1.0: USB hub found
[ 4.907069] hub 4-0:1.0: 2 ports detected
[ 4.915847] usbcore: registered new interface driver usb-storage
[ 4.932321] init: - preinit -
[ 5.675537] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.704372] eth0: link up (1000Mbps/Full duplex)
[ 6.709185] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.704304] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
[ 8.914835] mount_root: loading kmods from internal overlay
[ 9.353519] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 9.360867] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 9.367598] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 45.265818] jffs2: notice: (409) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 45.281791] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 45.288974] block: unable to load configuration (fstab: Entry not found)
[ 45.295876] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 45.302413] block: unable to load configuration (fstab: Entry not found)
[ 45.309354] block: attempting to load /etc/config/fstab
[ 45.316288] block: unable to load configuration (fstab: Entry not found)
[ 45.347836] block: no usable configuration
[ 45.400872] jffs2: notice: (406) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 45.690824] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 45.698007] block: unable to load configuration (fstab: Entry not found)
[ 45.704961] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 45.711505] block: unable to load configuration (fstab: Entry not found)
[ 45.718406] block: attempting to load /etc/config/fstab
[ 45.723880] block: unable to load configuration (fstab: Entry not found)
[ 45.730727] block: no usable configuration
[ 45.736475] mount_root: overlay filesystem has not been fully initialized yet
[ 45.745385] mount_root: switching to jffs2 overlay
- config restore -
[ 46.385424] eth0: link down
[ 46.397153] procd: - early -
[ 46.400157] procd: - watchdog -
[ 47.088142] procd: - ubus -
[ 47.218434] random: ubusd urandom read with 75 bits of entropy available
[ 47.227059] procd: - init -
Please press Enter to activate this console.
[ 48.765474] zram: Created 1 device(s)
[ 48.783811] tun: Universal TUN/TAP device driver, 1.6
[ 48.788941] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 48.813488] sit: IPv6 over IPv4 tunneling driver
[ 48.838731] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 48.893187] u32 classifier
[ 48.895939] input device check on
[ 48.899651] Actions configured
[ 48.915749] Mirror/redirect action on
[ 48.967742] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 48.975283] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 49.007865] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 49.031416] nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
[ 49.136533] xt_time: kernel timezone is -0000
[ 49.277371] usbcore: registered new interface driver ath9k_htc
[ 49.310270] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[ 53.438543] zram0: detected capacity change from 0 to 63963136
[ 53.803967] Adding 62460k swap on /dev/zram0. Priority:-1 extents:1 across:62460k SS
[ 57.988058] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 58.006634] device eth0.1 entered promiscuous mode
[ 58.011500] device eth0 entered promiscuous mode
[ 58.024375] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 58.076447] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 59.884423] eth0: link up (1000Mbps/Full duplex)
[ 59.889244] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 59.914318] br-lan: port 1(eth0.1) entered forwarding state
[ 59.920007] br-lan: port 1(eth0.1) entered forwarding state
[ 59.925810] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 60.022540] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 61.912951] br-lan: port 1(eth0.1) entered forwarding state
[ 80.012966] random: nonblocking pool is initialized
BusyBox v1.24.2 () built-in shell (ash)
_________
/ /\ _ ___ ___ ___
/ LE / \ | | | __| \| __|
/ DE / \ | |__| _|| |) | _|
/________/ LE \ |____|___|___/|___| lede-project.org
\ \ DE /
\ LE \ / -----------------------------------------------------------
\ DE \ / Reboot (HEAD, r222)
\________\/ -----------------------------------------------------------
root@airport:/# lspci
/bin/ash: lspci: not found
root@airport:/# lsusb
/bin/ash: lsusb: not found
root@airport:/# [ 413.047661] Removing MTD device #4 (rootfs_data) with use count 1
[ 413.071668] reboot: Restarting system
U-Boot 0.0.9 (Feb 18 2013 - 14:56:17)
Product Name: WN-AC1600DGR
ap136 - Scorpion 1.0
DRAM:128 MB
Now running in RAM - U-Boot at: 87fc8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
Flash size 16MB, sector count = 256
In: serial
Out: serial
Err: serial
reset_switch:
reset_usb:
Multi Net:
ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ----> S17 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs17_reg_init: SUPPORT_QCA8337
athrs17_reg_init S17_GLOFW_CTRL1_REG624=7f7f7f7f
athrs17_reg_init: MAC0 RGMII
athrs17_reg_init S17_P0PAD_MODE_REG04=87680000
athrs17_reg_init: Not SGMII_FORCED_MODE
athrs17_reg_init S17_PWS_REG10=40000000
athrs17_reg_init S17_P0STATUS_REG7c=7e
athrs17_reg_init QCA8337 ID=1302
athrs17_reg_init: complete
eth0 up
eth0
Setting 0x18116290 to 0x60c0214f
Please choose the operation:
1: Load system code to SDRAM via TFTP.
3: Boot system code via Flash (default).
 1  0
3: System Boot system code via Flash.
athrs17_set_portvlan_isolated complete
## Booting image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-4.1.20
Created: 2016-05-13 7:17:31 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1254576 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.1.20 (tenchi@tenchi-htpc) (gcc version 5.3.0 (LEDE GCC 5.3.0 r222) ) #2 Fri May 13 08:48:12 UTC 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=WLR8100 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),14080k(rootfs),192k(unknown)ro,64k(art)ro,384k(unknown2)ro,15488k@0x40000(firmware) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125404K/131072K available (2801K kernel code, 144K rwdata, 688K rodata, 260K init, 195K bss, 5668K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:240.000MHz, Ref:40.000MHz
[ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.008272] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.071178] pid_max: default: 32768 minimum: 301
[ 0.076178] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.083218] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092783] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.103693] NET: Registered protocol family 16
[ 0.109440] MIPS: machine is Sitecom WLR-8100
[ 0.556734] registering PCI controller with io_map_base unset
[ 0.562945] registering PCI controller with io_map_base unset
[ 0.575724] PCI host bridge to bus 0000:00
[ 0.580120] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.587430] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.593360] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.600576] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.609425] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x10007fff 64bit]
[ 0.617314] PCI host bridge to bus 0000:01
[ 0.621693] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.629001] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.634931] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.642147] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.650610] pci 0000:01:00.0: invalid calibration data
[ 0.656414] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.664226] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 0.671915] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.677203] pci 0000:01:00.0: using irq 41 for pin 1
[ 0.683091] Switched to clocksource MIPS
[ 0.688313] NET: Registered protocol family 2
[ 0.693686] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.701104] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.707909] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.714744] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.720965] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.727887] NET: Registered protocol family 1
[ 0.733424] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.753026] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.759284] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.771550] io scheduler noop registered
[ 0.775771] io scheduler deadline registered (default)
[ 0.781410] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.788524] console [ttyS0] disabled
[ 0.812382] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.821568] console [ttyS0] enabled
[ 0.821568] console [ttyS0] enabled
[ 0.828977] bootconsole [early0] disabled
[ 0.828977] bootconsole [early0] disabled
[ 0.839506] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.845398] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.850544] 8 cmdlinepart partitions found on MTD device spi0.0
[ 0.856562] Creating 8 MTD partitions on "spi0.0":
[ 0.861420] 0x000000000000-0x000000030000 : "u-boot"
[ 0.867156] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.873202] 0x000000040000-0x0000001a0000 : "kernel"
[ 0.878865] 0x0000001a0000-0x000000f60000 : "rootfs"
[ 0.884525] mtd: device 3 (rootfs) set to be root filesystem
[ 0.890325] 1 squashfs-split partitions found on MTD device rootfs
[ 0.896631] 0x000000b20000-0x000000f60000 : "rootfs_data"
[ 0.902729] 0x000000f60000-0x000000f90000 : "unknown"
[ 0.908518] 0x000000f90000-0x000000fa0000 : "art"
[ 0.913953] 0x000000fa0000-0x000001000000 : "unknown2"
[ 0.919780] 0x000000040000-0x000000f60000 : "firmware"
[ 0.940078] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[ 1.031233] libphy: ag71xx_mdio: probed
[ 1.624591] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.635905] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.224689] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[ 2.232698] NET: Registered protocol family 10
[ 2.240246] NET: Registered protocol family 17
[ 2.244859] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.257776] 8021q: 802.1Q VLAN Support v1.8
[ 2.268395] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.276533] Freeing unused kernel memory: 260K (803ef000 - 80430000)
[ 3.437426] init: Console is alive
[ 3.441051] init: - watchdog -
[ 5.382031] usbcore: registered new interface driver usbfs
[ 5.387710] usbcore: registered new interface driver hub
[ 5.393199] usbcore: registered new device driver usb
[ 5.435953] SCSI subsystem initialized
[ 5.444503] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.452299] ehci-platform: EHCI generic platform driver
[ 5.457707] ehci-platform ehci-platform.0: EHCI Host Controller
[ 5.463756] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 5.474025] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[ 5.480125] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 5.503127] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 5.510371] hub 1-0:1.0: USB hub found
[ 5.514461] hub 1-0:1.0: 1 port detected
[ 5.518728] ehci-platform ehci-platform.1: EHCI Host Controller
[ 5.524799] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 5.535084] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[ 5.541189] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 5.563115] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 5.570344] hub 2-0:1.0: USB hub found
[ 5.574430] hub 2-0:1.0: 1 port detected
[ 5.583963] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 5.589740] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 5.595101] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 3
[ 5.602844] xhci_hcd 0000:00:00.0: hcc params 0x040050af hci version 0x100 quirks 0x00080490
[ 5.612347] hub 3-0:1.0: USB hub found
[ 5.616469] hub 3-0:1.0: 2 ports detected
[ 5.620839] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 5.626193] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 4
[ 5.633835] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.642679] hub 4-0:1.0: USB hub found
[ 5.646797] hub 4-0:1.0: 2 ports detected
[ 5.655549] usbcore: registered new interface driver usb-storage
[ 5.672024] init: - preinit -
[ 6.380394] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.854521] eth0: link up (1000Mbps/Full duplex)
[ 7.859336] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.559595] mount_root: loading kmods from internal overlay
[ 9.063165] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 9.070560] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 9.077286] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 9.854458] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
[ 40.361056] done.
[ 40.363043] jffs2: notice: (419) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 40.379026] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 40.386179] block: unable to load configuration (fstab: Entry not found)
[ 40.393047] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 40.399691] block: unable to load configuration (fstab: Entry not found)
[ 40.406593] block: attempting to load /etc/config/fstab
[ 40.416510] block: unable to load configuration (fstab: Entry not found)
[ 40.423416] block: no usable configuration
[ 40.474639] jffs2: notice: (416) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 40.764762] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 40.771850] block: unable to load configuration (fstab: Entry not found)
[ 40.778812] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[ 40.785397] block: unable to load configuration (fstab: Entry not found)
[ 40.792251] block: attempting to load /etc/config/fstab
[ 40.797725] block: unable to load configuration (fstab: Entry not found)
[ 40.804611] block: no usable configuration
[ 40.810492] mount_root: overlay filesystem has not been fully initialized yet
[ 40.819408] mount_root: switching to jffs2 overlay
- config restore -
[ 41.476894] eth0: link down
[ 41.488211] procd: - early -
[ 41.491217] procd: - watchdog -
[ 42.175803] procd: - ubus -
[ 42.299252] random: ubusd urandom read with 67 bits of entropy available
[ 42.307848] procd: - init -
Please press Enter to activate this console.
[ 43.902281] zram: Created 1 device(s)
[ 43.939410] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 43.962887] tun: Universal TUN/TAP device driver, 1.6
[ 43.968056] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 43.979725] sit: IPv6 over IPv4 tunneling driver
[ 44.005143] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 44.043919] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 44.051425] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 44.184871] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 44.193158] ath10k_pci 0000:01:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
[ 44.407773] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[ 44.418307] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 44.494460] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 44.820035] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 44.829438] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 44.842513] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.97 api 5 features no-p2p crc32 f91e34f2
[ 44.891619] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 44.902223] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 44.979513] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 45.031056] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 45.187542] ath10k_pci 0000:01:00.0: otp calibration failed: 2
[ 45.193479] ath10k_pci 0000:01:00.0: failed to run otp: -22
[ 45.199133] ath10k_pci 0000:01:00.0: could not init core (-22)
[ 45.205152] ath10k_pci 0000:01:00.0: could not probe fw (-22)
[ 45.303942] u32 classifier
[ 45.306691] input device check on
[ 45.310403] Actions configured
[ 45.315968] Mirror/redirect action on
[ 45.392020] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 45.431681] nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
[ 45.497432] xt_time: kernel timezone is -0000
[ 45.513598] usbcore: registered new interface driver ath9k_htc
[ 45.557569] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[ 49.628478] zram0: detected capacity change from 0 to 63963136
[ 50.005079] Adding 62460k swap on /dev/zram0. Priority:-1 extents:1 across:62460k SS
[ 54.193206] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 54.214497] device eth0.1 entered promiscuous mode
[ 54.219369] device eth0 entered promiscuous mode
[ 54.231628] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 54.276459] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 56.094568] eth0: link up (1000Mbps/Full duplex)
[ 56.099388] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 56.126938] br-lan: port 1(eth0.1) entered forwarding state
[ 56.132626] br-lan: port 1(eth0.1) entered forwarding state
[ 56.138427] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 56.229831] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 58.123100] br-lan: port 1(eth0.1) entered forwarding state
BusyBox v1.24.2 () built-in shell (ash)
_________
/ /\ _ ___ ___ ___
/ LE / \ | | | __| \| __|
/ DE / \ | |__| _|| |) | _|
/________/ LE \ |____|___|___/|___| lede-project.org
\ \ DE /
\ LE \ / -----------------------------------------------------------
\ DE \ / Reboot (HEAD, r222)
\________\/ -----------------------------------------------------------
root@airport:/# [ 79.213115] random: nonblocking pool is initialized
root@airport:/#
root@airport:/# cd /lib
root@airport:/# cd /lib/firm
root@airport:/# cd /lib/firmware/a
root@airport:/# cd /lib/firmware/ath
ath10k/ ath9k_htc/
root@airport:/# cd /lib/firmware/ath1
root@airport:/# cd /lib/firmware/ath10k/
root@airport:/# cd /lib/firmware/ath10k/QCA988X/
root@airport:/# cd /lib/firmware/ath10k/QCA988X/hw2.0/
root@airport:/lib/firmware/ath10k/QCA988X/hw2.0# ls
board.bin firmware-5.bin
root@airport:/lib/firmware/ath10k/QCA988X/hw2.0# lmd5sum *
ab36ef267d15cfc02317ceeb38e8f548 board.bin
fcb2fbd42d73a63fbf603505c718cbde firmware-5.bin
root@airport:/lib/firmware/ath10k/QCA988X/hw2.0# nano /etc/modules.d/55-ath10k 
[ 354.383435] device eth0.1 left promiscuous mode
[ 354.388121] br-lan: port 1(eth0.1) entered disabled state
[ 354.400372] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 354.659143] device eth0 left promiscuous mode
[ 354.683262] eth0: link down
[ 358.659129] Removing MTD device #4 (rootfs_data) with use count 1
[ 358.681941] reboot: Restarting system
U-Boot 0.0.9 (Feb 18 2013 - 14:56:17)
Product Name: WN-AC1600DGR
ap136 - Scorpion 1.0
DRAM:128 MB
Now running in RAM - U-Boot at: 87fc8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
Flash size 16MB, sector count = 256
In: serial
Out: serial
Err: serial
reset_switch:
reset_usb:
Multi Net:
ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0xe
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ----> S17 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs17_reg_init: SUPPORT_QCA8337
athrs17_reg_init S17_GLOFW_CTRL1_REG624=7f7f7f7f
athrs17_reg_init: MAC0 RGMII
athrs17_reg_init S17_P0PAD_MODE_REG04=87680000
athrs17_reg_init: Not SGMII_FORCED_MODE
athrs17_reg_init S17_PWS_REG10=40000000
athrs17_reg_init S17_P0STATUS_REG7c=7e
athrs17_reg_init QCA8337 ID=1302
athrs17_reg_init: complete
eth0 up
eth0
Setting 0x18116290 to 0x60c0214f
Please choose the operation:
1: Load system code to SDRAM via TFTP.
3: Boot system code via Flash (default).
 1  0
3: System Boot system code via Flash.
athrs17_set_portvlan_isolated complete
## Booting image at 9f040000 ...
Image Name: MIPS OpenWrt Linux-4.1.20
Created: 2016-05-13 7:17:31 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1254576 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f040040 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.1.20 (tenchi@tenchi-htpc) (gcc version 5.3.0 (LEDE GCC 5.3.0 r222) ) #2 Fri May 13 08:48:12 UTC 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=WLR8100 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),14080k(rootfs),192k(unknown)ro,64k(art)ro,384k(unknown2)ro,15488k@0x40000(firmware) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125404K/131072K available (2801K kernel code, 144K rwdata, 688K rodata, 260K init, 195K bss, 5668K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:240.000MHz, Ref:40.000MHz
[ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.008272] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.071178] pid_max: default: 32768 minimum: 301
[ 0.076178] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.083218] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.092782] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.103694] NET: Registered protocol family 16
[ 0.109436] MIPS: machine is Sitecom WLR-8100
[ 0.556734] registering PCI controller with io_map_base unset
[ 0.562945] registering PCI controller with io_map_base unset
[ 0.575714] PCI host bridge to bus 0000:00
[ 0.580112] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.587422] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.593351] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.600568] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.609417] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x10007fff 64bit]
[ 0.617305] PCI host bridge to bus 0000:01
[ 0.621685] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.628993] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.634923] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.642139] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.650602] pci 0000:01:00.0: invalid calibration data
[ 0.656408] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.664218] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 0.671907] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.677195] pci 0000:01:00.0: using irq 41 for pin 1
[ 0.683082] Switched to clocksource MIPS
[ 0.688303] NET: Registered protocol family 2
[ 0.693670] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.701087] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.707891] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.714727] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.720948] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.727872] NET: Registered protocol family 1
[ 0.733408] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.753009] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.759266] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.771535] io scheduler noop registered
[ 0.775755] io scheduler deadline registered (default)
[ 0.781392] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.788507] console [ttyS0] disabled
[ 0.812366] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.821545] console [ttyS0] enabled
[ 0.821545] console [ttyS0] enabled
[ 0.828963] bootconsole [early0] disabled
[ 0.828963] bootconsole [early0] disabled
[ 0.839491] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.845385] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.850529] 8 cmdlinepart partitions found on MTD device spi0.0
[ 0.856539] Creating 8 MTD partitions on "spi0.0":
[ 0.861396] 0x000000000000-0x000000030000 : "u-boot"
[ 0.867130] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.873181] 0x000000040000-0x0000001a0000 : "kernel"
[ 0.878844] 0x0000001a0000-0x000000f60000 : "rootfs"
[ 0.884509] mtd: device 3 (rootfs) set to be root filesystem
[ 0.890310] 1 squashfs-split partitions found on MTD device rootfs
[ 0.896617] 0x000000b20000-0x000000f60000 : "rootfs_data"
[ 0.902713] 0x000000f60000-0x000000f90000 : "unknown"
[ 0.908504] 0x000000f90000-0x000000fa0000 : "art"
[ 0.913940] 0x000000fa0000-0x000001000000 : "unknown2"
[ 0.919767] 0x000000040000-0x000000f60000 : "firmware"
[ 0.940080] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[ 1.031230] libphy: ag71xx_mdio: probed
[ 1.624583] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 1.635901] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.224680] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[ 2.232693] NET: Registered protocol family 10
[ 2.240246] NET: Registered protocol family 17
[ 2.244862] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.257779] 8021q: 802.1Q VLAN Support v1.8
[ 2.268403] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.276534] Freeing unused kernel memory: 260K (803ef000 - 80430000)
[ 3.437498] init: Console is alive
[ 3.441118] init: - watchdog -
[ 5.382279] usbcore: registered new interface driver usbfs
[ 5.387960] usbcore: registered new interface driver hub
[ 5.393447] usbcore: registered new device driver usb
[ 5.437773] SCSI subsystem initialized
[ 5.446120] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.453966] ehci-platform: EHCI generic platform driver
[ 5.459332] ehci-platform ehci-platform.0: EHCI Host Controller
[ 5.465400] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 5.475672] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[ 5.481774] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 5.503117] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 5.510365] hub 1-0:1.0: USB hub found
[ 5.514445] hub 1-0:1.0: 1 port detected
[ 5.518715] ehci-platform ehci-platform.1: EHCI Host Controller
[ 5.524785] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 5.535070] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[ 5.541174] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 5.563105] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 5.570338] hub 2-0:1.0: USB hub found
[ 5.574418] hub 2-0:1.0: 1 port detected
[ 5.583908] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 5.589681] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 5.595042] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 3
[ 5.602787] xhci_hcd 0000:00:00.0: hcc params 0x040050af hci version 0x100 quirks 0x00080490
[ 5.612281] hub 3-0:1.0: USB hub found
[ 5.616408] hub 3-0:1.0: 2 ports detected
[ 5.620773] xhci_hcd 0000:00:00.0: xHCI Host Controller
[ 5.626126] xhci_hcd 0000:00:00.0: new USB bus registered, assigned bus number 4
[ 5.633766] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 5.642606] hub 4-0:1.0: USB hub found
[ 5.646728] hub 4-0:1.0: 2 ports detected
[ 5.655494] usbcore: registered new interface driver usb-storage
[ 5.671965] init: - preinit -
[ 6.380326] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.854513] eth0: link up (1000Mbps/Full duplex)
[ 7.859331] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 8.559821] mount_root: loading kmods from internal overlay
[ 9.084311] jffs2: notice: (419) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.100468] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 9.112449] block: extroot: not configured
[ 9.173604] jffs2: notice: (416) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.476327] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 9.487643] block: extroot: not configured
[ 9.492509] mount_root: switching to jffs2 overlay
[ 9.522698] eth0: link down
[ 9.534451] procd: - early -
[ 9.537453] procd: - watchdog -
[ 10.215967] procd: - ubus -
[ 10.339026] random: ubusd urandom read with 17 bits of entropy available
[ 10.349479] procd: - init -
Please press Enter to activate this console.
[ 11.914946] zram: Created 1 device(s)
[ 11.950518] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 11.973868] tun: Universal TUN/TAP device driver, 1.6
[ 11.978994] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 11.990668] sit: IPv6 over IPv4 tunneling driver
[ 12.016349] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.051225] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 12.058768] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 12.191186] ath10k_pci: unknown parameter 'skip_otp' ignored
[ 12.207405] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 12.213609] ath10k_pci 0000:01:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
[ 12.427772] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[ 12.438303] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.514932] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 12.840982] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 12.850386] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 12.863472] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.97 api 5 features no-p2p crc32 f91e34f2
[ 12.912552] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 12.923165] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 12.999174] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 13.050713] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 14.261752] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[ 14.541115] u32 classifier
[ 14.543905] input device check on
[ 14.547614] Actions configured
[ 14.553183] Mirror/redirect action on
[ 14.615426] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.655006] nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
[ 14.722185] xt_time: kernel timezone is -0000
[ 14.738389] usbcore: registered new interface driver ath9k_htc
[ 14.782618] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[ 17.616952] zram0: detected capacity change from 0 to 63963136
[ 18.051124] Adding 62460k swap on /dev/zram0. Priority:-1 extents:1 across:62460k SS
[ 22.229178] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.246821] device eth0.1 entered promiscuous mode
[ 22.251692] device eth0 entered promiscuous mode
[ 22.267781] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 22.313815] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 24.054549] eth0: link up (1000Mbps/Full duplex)
[ 24.059371] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 24.084291] br-lan: port 1(eth0.1) entered forwarding state
[ 24.089983] br-lan: port 1(eth0.1) entered forwarding state
[ 24.095789] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 24.202817] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 26.083088] br-lan: port 1(eth0.1) entered forwarding state
[ 26.114441] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
BusyBox v1.24.2 () built-in shell (ash)
_________
/ /\ _ ___ ___ ___
/ LE / \ | | | __| \| __|
/ DE / \ | |__| _|| |) | _|
/________/ LE \ |____|___|___/|___| lede-project.org
\ \ DE /
\ LE \ / -----------------------------------------------------------
\ DE \ / Reboot (HEAD, r222)
\________\/ -----------------------------------------------------------
root@airport:/# ifconfig -a
br-lan Link encap:Ethernet HWaddr 88:1F:A1:15:35:A3
inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0
inet6 addr: fe80::8a1f:a1ff:fe15:35a3/64 Scope:Link
inet6 addr: fd6d:da15:b8d1::1/60 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:29 errors:0 dropped:0 overruns:0 frame:0
TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5650 (5.5 KiB) TX bytes:2880 (2.8 KiB)
eth0 Link encap:Ethernet HWaddr 9A:09:14:79:95:D8
inet6 addr: fe80::9809:14ff:fe79:95d8/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:41 errors:0 dropped:0 overruns:0 frame:0
TX packets:60 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8136 (7.9 KiB) TX bytes:10338 (10.0 KiB)
Interrupt:4
eth0.1 Link encap:Ethernet HWaddr 9A:09:14:79:95:D8
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:38 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:6459 (6.3 KiB) TX bytes:2542 (2.4 KiB)
eth0.2 Link encap:Ethernet HWaddr 88:1F:A1:15:35:A1
inet6 addr: fe80::8a1f:a1ff:fe15:35a1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:29 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:6454 (6.3 KiB)
eth1 Link encap:Ethernet HWaddr 7A:6E:3E:F3:8D:09
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:5
ifb0 Link encap:Ethernet HWaddr 92:7B:1B:FB:2D:7C
BROADCAST NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
ifb1 Link encap:Ethernet HWaddr FA:5B:96:5B:41:3B
BROADCAST NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:42 errors:0 dropped:0 overruns:0 frame:0
TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2863 (2.7 KiB) TX bytes:2863 (2.7 KiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
teql0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan1 Link encap:Ethernet HWaddr 00:02:6F:12:34:56
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@airport:/# iw phy phy0 info
Wiphy phy0
max # scan SSIDs: 16
max scan IEs length: 195 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* managed
* AP
* AP/VLAN
* monitor
* mesh point
Band 1:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x338001b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x338001b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 no[ 67.601526] random: nonblocking pool is initialized
r 80+80
RX LDPC
short GI (80 MHz)
TX STBC
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5280 MHz [56] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5300 MHz [60] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5320 MHz [64] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5500 MHz [100] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5520 MHz [104] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5540 MHz [108] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5560 MHz [112] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5580 MHz [116] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5600 MHz [120] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5620 MHz [124] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5640 MHz [128] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5660 MHz [132] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5680 MHz [136] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5700 MHz [140] (23.0 dBm) (no IR, radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5720 MHz [144] (23.0 dBm) (radar detection)
DFS state: usable (for 53 sec)
DFS CAC time: 60000 ms
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
valid interface combinations:
* #{ AP, mesh point } <= 8, #{ managed } <= 1,
total <= 8, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports VHT-IBSS.
root@airport:/#
root@airport:/# iw phy phy0 info info1 info info
Wiphy phy1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* mesh point
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
Frequencies:
* 2412 MHz [1] (22.0 dBm)
* 2417 MHz [2] (22.0 dBm)
* 2422 MHz [3] (22.0 dBm)
* 2427 MHz [4] (22.0 dBm)
* 2432 MHz [5] (22.0 dBm)
* 2437 MHz [6] (22.0 dBm)
* 2442 MHz [7] (22.0 dBm)
* 2447 MHz [8] (22.0 dBm)
* 2452 MHz [9] (22.0 dBm)
* 2457 MHz [10] (22.0 dBm)
* 2462 MHz [11] (22.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz }
* #{ WDS } <= 2048,
total <= 2048, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
root@airport:/# [ 94.125765] IPv6: ADDRCONF(NETDEV_UP): tmp.radio1: link is not ready
[ 101.032684] IPv6: ADDRCONF(NETDEV_UP): tmp.radio1: link is not ready
[ 107.929556] IPv6: ADDRCONF(NETDEV_UP): tmp.radio1: link is not ready
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment