ptracton/modelsim_installation.md

## modelsim_installation.md

      
    Raw
  

              modelsim_installation.md
            
          
    ModelSim Installation issues

Ubuntu 14.xx and above

Ignore this if you have not encountered any issue with the installation and running of ModelSim and Quartus on your system. You are very lucky. (Just Kidding! You have surely had this issue, only sorted.)
Hence assuming you have been following the procedure given in this guide. Most certainly, Quartus will install jsut fine, and so will ModelSim. The issue is in launching due to inappropriate linking etc.
Stage 1

This is the simplest error you would encounter. Navigate to the modelsim_ase folder and run:
cd /opt/modelsim_ase/bin/
./vsim
Unless you have not updated your Linux kernel in the last 3 years, you are most certain to encounter an error saying could not find ./../linux_rh60/vsim. To understand this (optional) you can open the file vsim and notice that in the if...elseif conditions, the default description points towards a folder for the Red Hat distro.

(This setup will only work for you without changes IF your Linux kernel is 3.x or below. Highly unlikely. Check using uname -r).
Okay, all of that aside, basically you need to replace this as (sudo is your friend!) :
*)                vco="linux" ;; # This is most likely to be line 212 (initially vco="linux_rh60")
Also, change the very first non-commented line to:
mode=${MTI_VCO_MODE:-"32"}
This should be adequate for most of you, and running /opt/modelsim_ase/bin/vsim will open a plain boring GUI. For that lot, thanks a lot for sticking around! Hope it helped. The others, keep following.
Stage 2

Here is where things get nasty. Does running the vsim script lead to:
** Fatal: Read failure in vlm process (0,0)
Segmentation fault (core dumped)
If yes, hang on. If not, I am sorry! Google is your friend!
I am guessing this issue came up for me because of the infinite existing packages on my system, including ROS. That seems to have ruined the setup for me, and hence more learning about the intricacies of compilation and linking. Totally worth it!
Okay, so here's what you would have to do. You probably need to build a new version of freetype, a font setting library and modify ModelSim to use it. You can download the source code for freetype here.
sudo apt-get build-dep -a i386 libfreetype6
# The above forced me to uninstall my ROS packages, and well.. I had no choice. Temporarily, let's remove them and proceed
cd ~/Downloads/
cd freetype-2.4.12
./configure --build=i686-pc-linux-gnu "CFLAGS=-m32" "CXXFLAGS=-m32" "LDFLAGS=-m32"
make -j8
Most certainly, the above would give you an error looking like:
checking whether the C++ compiler works... no
...
configure: error: C++ compiler cannot create executables

This is because you could be on a 64-bit system but you will also need the 32-bit versions of the libraries that it depends on. After an hour of fretting, here's what you'll have to do.
sudo dpkg --add-architecture i386
sudo apt-get update
sudo apt-get install build-essential
# You already had build-essential and gcc, g++ etc. But you will also need to install the 32 bit versions.

sudo apt-get install gcc-multilib g++-multilib \
lib32z1 lib32stdc++6 lib32gcc1 \
expat:i386 fontconfig:i386 libfreetype6:i386 libexpat1:i386 libc6:i386 libgtk-3-0:i386 \
libcanberra0:i386 libpng12-0:i386 libice6:i386 libsm6:i386 libncurses5:i386 zlib1g:i386 \
libx11-6:i386 libxau6:i386 libxdmcp6:i386 libxext6:i386 libxft2:i386 libxrender1:i386 \
libxt6:i386 libxtst6:i386
This just about solves the dependency issues and compiler errors. Run the following inside freetype... folder.
./configure --build=i686-pc-linux-gnu "CFLAGS=-m32" "CXXFLAGS=-m32" "LDFLAGS=-m32"
make -j8
This should nicely compile and give you the libraries in the directory objs/.libs/. Move this to the modelsim_ase folder and define the linkings. Almost done here...
mkdir /opt/modelsim_ase/lib32

sudo cp ~/Downloads/freetype-2.4.12/objs/.libs/libfreetype.so* /opt/modelsim_ase/lib32

sudo vim /opt/modelsim_ase/bin/vsim
Find the line which says
dir=`dirname $arg0`
(Note that this occurs in multiple locations. In simple terms, look at the one in the main sequence of execution, and not in the if statement. You can ignore the one under CYGWIN. Cygwin is for Windows. Windows is for losers! :p Apologies.)
Below this add the line:
export LD_LIBRARY_PATH=${dir}/lib32
Save this file. This would only be possible if you have sudo permissions. And finally!
cd /opt/modelsim_ase/bin/
./vsim
Hopefully, a plain boring GUI will show up!
Hope this helped. Cheers!

Dhruv