Tunneling a whole process through wireguard

tunneling.md

Tunneling a whole process through wireguard

Certain company blocking a certain hosting provider? No problem, just tunnel the process through a small VPS with wireguard.

Consider server A your blocked server and server B your VPS.

Step 1: Generate a keypair on server A and server B

Server A:

wg genkey > endpoint-a.key
wg pubkey < endpoint-a.key > endpoint-a.pub

Server B:

wg genkey > endpoint-b.key
wg pubkey < endpoint-b.key > endpoint-b.pub

Step 2: Configure server B

Edit /etc/sysctl.conf and ensure the following line is uncommented:

net.ipv4.ip_forward=1

Create a wireguard config at /etc/wireguard/wg0.conf with the following content:

[Interface]
PrivateKey = <endpoint-b.key>
Address = 10.0.0.2/32
ListenPort = 51822

PreUp = iptables -t mangle -A PREROUTING -i wg0 -j MARK --set-mark 0x30
PreUp = iptables -t nat -A POSTROUTING ! -o wg0 -m mark --mark 0x30 -j MASQUERADE
PostDown = iptables -t mangle -D PREROUTING -i wg0 -j MARK --set-mark 0x30
PostDown = iptables -t nat -D POSTROUTING ! -o wg0 -m mark --mark 0x30 -j MASQUERADE

[Peer]
PublicKey = <endpoint-a.pub>
AllowedIPs = 10.0.0.1/32
Endpoint = <server A ip address>:51822

If you wish to forward ports, add the following 2 lines under [Interface] per port you wish to forward:

PreUp = iptables -t nat -A PREROUTING -p tcp --dport 12345 -j DNAT --to-destination 10.0.0.1
PostDown = iptables -t nat -D PREROUTING -p tcp --dport 12345 -j DNAT --to-destination 10.0.0.1

Enable & start wg0 using wg-quick:

systemctl enable --now wg-quick@wg0

Step 3: Configure server A

Create a wireguard config at /etc/wireguard/wg0.conf with the following content:

[Interface]
PrivateKey = <endpoint-a.key>
ListenPort = 51821

[Peer]
PublicKey = <endpoint-b.pub>
Endpoint = <server B ip address>:51822
AllowedIPs = 0.0.0.0/0

Create a script to setup the namespace:

cat <<EOF | sudo tee /etc/wireguard/netns_setup.sh
ip netns add pvt-net1
ip -n pvt-net1 link set lo up
ip link add wg0 type wireguard
ip link set wg0 netns pvt-net1
ip netns exec pvt-net1 wg setconf wg0 /etc/wireguard/wg0.conf
ip -n pvt-net1 address add 10.0.0.1/32 dev wg0
ip -n pvt-net1 link set wg0 up
ip -n pvt-net1 route add default dev wg0
EOF

Make script executable:

chmod +x /etc/wireguard/netns_setup.sh

Make DNS work:

mkdir -p /etc/netns/pvt-net1
echo nameserver 1.1.1.1 | sudo tee /etc/netns/pvt-net1/resolv.conf >/dev/null
chmod -R o+rX /etc/netns

Create systemd service to execute this on boot:

cat <<EOF | sudo tee /etc/systemd/system/tunnel1.service
[Unit]
Description=Tunnel 1
After=network.target wg-quick@wg0.target

[Service]
ExecStart=/etc/wireguard/netns_setup.sh
Type=oneshot
RemainAfterExit=yes

[Install]
WantedBy=multi-user.target
EOF

Execute on boot & execute now:

systemctl enable --now tunnel1

Use a systemd override to bind to network namespace & ensure service is started after tunnel is up:

systemctl edit <service>

Add the following at the top, in the override section (you may have to change After=:

[Unit]
After=network.target network-online.target tunnel1.target

[Service]
NetworkNamespacePath=/run/netns/pvt-net1
BindReadOnlyPaths=/etc/netns/pvt-net1/resolv.conf:/etc/resolv.conf

Reload systemd & restart service:

systemctl daemon-reload
systemctl restart <your service>

Credit

This whole config was derived from https://www.procustodibus.com/blog/2023/04/wireguard-netns-for-specific-apps. All credit goes to them!