t113 builroot sd无法启动

log.txt

[89]HELLO! BOOT0 is starting!
[92]BOOT0 commit : 1417090655
[95]set pll start
[96]fix vccio detect value:0xc0
[104]periph0 has been enabled
[107]set pll end
[108][pmu]: bus read error
[111]board init ok
[113]enable_jtag
[114]ZQ value = 0x2f
[116]get_pmu_exist() = -1
[119]ddr_efuse_type: 0xa
[121]trefi:7.8ms
[124][AUTO DEBUG] single rank and full DQ!
[128]ddr_efuse_type: 0xa
[130]trefi:7.8ms
[133][AUTO DEBUG] rank 0 row = 13
[136][AUTO DEBUG] rank 0 bank = 8
[139][AUTO DEBUG] rank 0 page size = 2 KB
[143]DRAM BOOT DRIVE INFO: V0.33
[146]DRAM CLK = 792 MHz
[148]DRAM Type = 3 (2:DDR2,3:DDR3)
[152]DRAMC read ODT  off.
[154]DRAM ODT value: 0x42.
[157]ddr_efuse_type: 0xa
[160]DRAM SIZE =128 M
[162]dram_tpr4:0x0
[164]PLL_DDR_CTRL_REG:0xf8004100
[167]DRAM_CLK_REG:0xc0000000
[170][TIMING DEBUG] MR2= 0x18
[178]DRAM simple test OK.
[180]rtc standby flag is 0x0, super standby flag is 0x0
[185]dram size =128
[188]card no is 0
[190]sdcard 0 line count 4
[192][mmc]: mmc driver ver 2021-05-21 14:47
[201][mmc]: Wrong media type 0x0
[204][mmc]: ***Try SD card 0***
[213][mmc]: HSSDR52/SDR25 4 bit
[216][mmc]: 50000000 Hz
[219][mmc]: 7386 MB
[220][mmc]: ***SD/MMC 0 init OK!!!***
[315]Loading boot-pkg Succeed(index=0).
[319]Entry_name        = u-boot
[326]Entry_name        = optee
[330]Entry_name        = dtb
[333]mmc not para
[335]Jump to second Boot.
M/TC: OP-TEE version: 8b49ce62-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Fri Aug 12 08:24:15 UTC 2022 arm


U-Boot 2018.07-gd9e6718-dirty (Feb 23 2024 - 14:21:42 +0800) Allwinner Technology

[00.387]CPU:   Allwinner Family
[00.389]Model: sun8iw20
[00.392]DRAM:  128 MiB
[00.395]Relocation Offset is: 04ec4000
[00.422]secure enable bit: 0
E/TC:0   fdt_getprop_u32:343 prop trace_level not found
[00.435]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.442]gic: sec monitor mode
sunxi flash map init
SPI ALL:   ready
[00.449]flash init start
[00.451]workmode = 0,storage type = 1
get value error
[00.456][mmc]: mmc driver ver uboot2018:2022-12-07 18:56:00
[00.461][mmc]: get sdc_type fail and use default host:tm1.
[00.467][mmc]: can't find node "mmc0",will add new node
[00.472][mmc]: fdt err returned <no error>
[00.476][mmc]: Using default timing para
[00.479][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.497][mmc]: card_caps:0x3000000a
[00.500][mmc]: host_caps:0x3000003f
[00.504]sunxi flash init ok
[00.506]line:703 init_clocks
[00.509]drv_disp_init
[00.514]handle_num : 6
request pwm success, pwm7:pwm7:0x2000c00.
[00.524]drv_disp_init finish
[00.534]Loading Environment from SUNXI_FLASH... OK
[00.554]boot_gui_init:start
[00.556]set disp.dev2_output_type fail. using defval=0
[00.563]set disp.fb0_rot_used fail. using defval=0
[00.567]set disp.fb0_rot_degree fail. using defval=0
[00.572]boot_gui_init:finish
partno erro : can't find partition bootloader
[00.582]bmp_name=bootlogo.bmp size 4096054
[00.743]LCD open finish
no support big size bmp[800x1280] on fb[800x480]
[00.766]show bmp on fb failed !-1
[00.771]Item0 (Map) magic is bad
[00.774]the secure storage item0 copy0 magic is bad
[00.779]Item0 (Map) magic is bad
[00.782]the secure storage item0 copy1 magic is bad
[00.787]Item0 (Map) magic is bad
secure storage read hdcpkey fail
[00.793]secure storage read hdcpkey fail with:-1
[00.797]usb burn from boot
delay time 0
weak:otg_phy_config
[00.808]usb prepare ok
[01.111]overtime
[01.114]do_burn_from_boot usb : no usb exist
partno erro : can't find partition private
partno erro : can't find partition private
partno erro : can't find partition private
partno erro : can't find partition private
partno erro : can't find partition private
partno erro : can't find partition private
[01.146]update part info
[01.149]update bootcmd
[01.156]change working_fdt 0x45e83e70 to 0x45e63e70
disable nand error: FDT_ERR_BADPATH
get value error
[01.166][mmc]: get sunxi-mmc0 string failed
[01.170]The storage not support sample function
[01.187]update dts
Hit any key to stop autoboot:  0
dsp0:dsp close in dts
boot  addr 0x43000000 0x4345e000 exceed dsp0 scope
dsp0  addr 0x43000000 0x430fc000
[03.445]no vendor_boot partition is found
Android's image name: sun8i_arm
ERROR: reserving fdt memory region failed (addr=41900000 size=200000)
ERROR: reserving fdt memory region failed (addr=41c00000 size=400000)
ERROR: reserving fdt memory region failed (addr=41b00000 size=100000)
ERROR: reserving fdt memory region failed (addr=45f0e000 size=177000)
ERROR: reserving fdt memory region failed (addr=42000000 size=100000)
ERROR: reserving fdt memory region failed (addr=42240000 size=2000)
ERROR: reserving fdt memory region failed (addr=42242000 size=2000)
ERROR: reserving fdt memory region failed (addr=42100000 size=10000)
[03.518]Starting kernel ...

[03.520][mmc]: MMC Device 2 not found
[03.524][mmc]: mmc 2 not find, so not exit
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.61 (qichunren@qichunren-VirtualBox) (arm-linux-gnueabi-gcc (Linaro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Linaro 2016_02) #1 SMP PREEMPT Fri Feb 23 13:57:42 CST 2024
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: sun8iw20
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created DMA memory pool at 0x42200000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node vdev0buffer@42200000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x42244000, size 0 MiB
[    0.000000] OF: reserved mem: initialized node dsp0_rpbuf@42244000, compatible id shared-dma-pool
[    0.000000] cma: Reserved 8 MiB at 0x47800000
[    0.000000] On node 0 totalpages: 32420
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32420 pages, LIFO batch:7
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s30784 r8192 d22464 u61440
[    0.000000] pcpu-alloc: s30784 r8192 d22464 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32164
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:UDISK@mmcblk0p7 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun8iw20p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.07-gd9e6718-dirty(02/23/2024-14:21:42) mbr_offset=1032192 disp_reserve=1536000,0x45f0e000 androidboot.dramsize=128
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 99520K/129680K available (6144K kernel code, 304K rwdata, 2280K rodata, 1024K init, 1168K bss, 21968K reserved, 8192K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x25c/0x3dc with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000017] Switching to timer-based delay loop, resolution 41ns
[    0.000190] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000796] Console: colour dummy device 80x30
[    0.000836] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000848] pid_max: default: 32768 minimum: 301
[    0.000975] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.000988] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.001585] CPU: Testing write buffer coherency: ok
[    0.001914] /cpus/cpu@0 missing clock-frequency property
[    0.001935] /cpus/cpu@1 missing clock-frequency property
[    0.001945] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.002471] Setting up static identity map for 0x40100000 - 0x40100060
[    0.002581] rcu: Hierarchical SRCU implementation.
[    0.003006] smp: Bringing up secondary CPUs ...
[    0.004176] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.004301] smp: Brought up 1 node, 2 CPUs
[    0.004315] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.004321] CPU: All CPU(s) started in SVC mode.
[    0.004780] devtmpfs: initialized
[    0.016351] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.016915] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.016942] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.017458] pinctrl core: initialized pinctrl subsystem
[    0.018767] NET: Registered protocol family 16
[    0.020269] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.058296] rtc_ccu: sunxi ccu init OK
[    0.060651] ccu: sunxi ccu init OK
[    0.061162] r_ccu: sunxi ccu init OK
[    0.095013] sun6i-dma 3002000.dma-controller: sunxi dma probed
[    0.097460] iommu: Default domain type: Translated
[    0.097657] sunxi iommu: irq = 24
[    0.098745] SCSI subsystem initialized
[    0.099103] usbcore: registered new interface driver usbfs
[    0.099189] usbcore: registered new interface driver hub
[    0.099836] usbcore: registered new device driver usb
[    0.100058] videodev: Linux video capture interface: v2.00
[    0.102239] Advanced Linux Sound Architecture Driver Initialized.
[    0.102919] Bluetooth: Core ver 2.22
[    0.102995] NET: Registered protocol family 31
[    0.103003] Bluetooth: HCI device and connection manager initialized
[    0.103027] Bluetooth: HCI socket layer initialized
[    0.103038] Bluetooth: L2CAP socket layer initialized
[    0.103064] Bluetooth: SCO socket layer initialized
[    0.103333] pwm module init!
[    0.106446] g2d 5410000.g2d: Adding to iommu group 0
[    0.106864] G2D: rcq version initialized.major:250
[    0.107941] clocksource: Switched to clocksource arch_sys_counter
[    0.117225] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[    0.131915] thermal_sys: Registered thermal governor 'step_wise'
[    0.131923] thermal_sys: Registered thermal governor 'power_allocator'
[    0.132458] NET: Registered protocol family 2
[    0.133016] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.133044] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.133067] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.133089] TCP: Hash tables configured (established 1024 bind 1024)
[    0.133178] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.133212] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.133423] NET: Registered protocol family 1
[    0.134476] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[    0.134969] spi spi0: spi0 supply spi not found, using dummy regulator
[    0.135153] sunxi_spi_resource_get()2259 - [spi0] SPI MASTER MODE
[    0.135203] sunxi_spi_resource_get()2297 - Failed to get sample mode
[    0.135211] sunxi_spi_resource_get()2302 - Failed to get sample delay
[    0.135220] sunxi_spi_resource_get()2306 - sample_mode:-1431633921 sample_delay:-1431633921
[    0.135249] sunxi_spi_request_dma()988 - [spi0] Request DMA channel dma0chan0 (tx) and dma0chan1 (rx) for DMA transfers
[    0.135324] sunxi_spi_clk_init()2356 - [spi0] mclk 100000000
[    0.135975] sunxi_spi_probe()2809 - [spi0]: driver probe succeed, base c881f000, irq 40
[    0.137899] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.145015] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.145217] ntfs: driver 2.1.32 [Flags: R/W].
[    0.145484] fuse: init (API version 7.31)
[    0.178267] io scheduler mq-deadline registered
[    0.178283] io scheduler kyber registered
[    0.179624] [DISP]disp_module_init
[    0.180226] disp 5000000.disp: Adding to iommu group 0
[    0.180752] [DISP] parser_disp_init_para,line:1407:
[    0.180755] of_property_read fb0_width fail
[    0.180771] [DISP] disp_init,line:2331:
[    0.180774] smooth display screen:0 type:1 mode:4
[    0.196974] display_fb_request,fb_id:0
[    0.201266] disp_al_manager_apply ouput_type:1
[    0.201684] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[    0.202264] [DISP]disp_module_init finish
[    0.203504] sunxi_sid_init()783 - insmod ok
[    0.204754] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[    0.205123] uart uart0: uart0 supply uart not found, using dummy regulator
[    0.205427] uart0: ttyS0 at MMIO 0x2500000 (irq = 34, base_baud = 1500000) is a SUNXI
[    0.205454] sw_console_setup()1831 - console setup baud 115200 parity n bits 8, flow n
[    0.434965] Freeing logo buffer memory: 1500K
[    1.112694] printk: console [ttyS0] enabled
[    1.118152] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[    1.129590] uart uart1: uart1 supply uart not found, using dummy regulator
[    1.137525] uart1: ttyS1 at MMIO 0x2500400 (irq = 35, base_baud = 1500000) is a SUNXI
[    1.147327] misc dump reg init
[    1.152216] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[    1.159478] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[    1.166752] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[    1.174142] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[    1.180646] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[    1.187533] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[    1.195218] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=131 assert=1
[    1.202984] sun8iw20-pinctrl 2000000.pinctrl: pin PE3 already requested by 2500000.uart; cannot claim for 2000000.pinctrl:131
[    1.215581] sun8iw20-pinctrl 2000000.pinctrl: pin-131 (2000000.pinctrl:131) status -22
[    1.224412] sunxi-rfkill soc@3000000:rfkill@0: can't request wlan_regon gpio 131
[    1.232682] sunxi-rfkill: probe of soc@3000000:rfkill@0 failed with error -22
[    1.241084] [ADDR_MGT] addr_mgt_probe: module version: v1.0.11
[    1.248307] [ADDR_MGT] addr_mgt_probe: success.
[    1.253718] dma-buf: Running sanitycheck
[    1.258128] dma-buf: Running dma_fence
[    1.262293] sizeof(dma_fence)=48
[    1.266005] dma-buf: Running dma_fence/sanitycheck
[    1.271366] dma-buf: Running dma_fence/test_signaling
[    1.276999] dma-buf: Running dma_fence/test_add_callback
[    1.282924] dma-buf: Running dma_fence/test_late_add_callback
[    1.289323] dma-buf: Running dma_fence/test_rm_callback
[    1.295148] dma-buf: Running dma_fence/test_late_rm_callback
[    1.301451] dma-buf: Running dma_fence/test_status
[    1.306808] dma-buf: Running dma_fence/test_error
[    1.312049] dma-buf: Running dma_fence/test_wait
[    1.317183] dma-buf: Running dma_fence/test_wait_timeout
[    1.357954] dma-buf: Running dma_fence/test_stub
[    1.363105] dma-buf: Running dma_fence/race_signal_callback
[    1.437947] thread_signal_callback[0] completed 35703 passes, 72 misses
[    1.445337] thread_signal_callback[1] completed 35685 passes, 55 misses
[    1.517966] thread_signal_callback[0] completed 41089 passes, 41086 misses
[    1.525635] thread_signal_callback[1] completed 41082 passes, 41082 misses
[    1.533930] sunxi-spinand: AW SPINand MTD Layer Version: 2.3 20211223
[    1.541161] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306
[    1.552269] random: fast init done
[    1.854864] random: crng init done
[    2.547963] sunxi-spinand-phy: read id failed : -110
[    2.553519] spi-nand: probe of spi0.0 failed with error -110
[    2.560294] libphy: Fixed MDIO Bus: probed
[    2.564951] usbcore: registered new interface driver asix
[    2.571062] usbcore: registered new interface driver ax88179_178a
[    2.577895] usbcore: registered new interface driver cdc_ether
[    2.584462] usbcore: registered new interface driver net1080
[    2.590823] usbcore: registered new interface driver cdc_subset
[    2.597459] usbcore: registered new interface driver zaurus
[    2.603774] usbcore: registered new interface driver cdc_ncm
[    2.610098] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.617356] sunxi-ehci: EHCI SUNXI driver
[    2.622258] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.629185] sunxi-ohci: OHCI SUNXI driver
[    2.634596] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1
[    2.645822] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    2.656479] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    2.667614] sunxi-rtc 7090000.rtc: registered as rtc0
[    2.673292] sunxi-rtc 7090000.rtc: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[    2.683857] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:05 UTC (5)
[    2.692707] sunxi-rtc 7090000.rtc: sunxi rtc probed
[    2.698646] i2c /dev entries driver
[    2.702681] IR NEC protocol handler initialized
[    2.708137] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[    2.719451] Registered IR keymap rc_map_sunxi
[    2.724459] rc rc0: sunxi-ir as /devices/platform/soc@3000000/7040000.s_cir/rc/rc0
[    2.733114] rc rc0: lirc_dev: driver sunxi-rc-recv registered at minor = 0, raw IR receiver, no transmitter
[    2.744188] input: sunxi-ir as /devices/platform/soc@3000000/7040000.s_cir/rc/rc0/s_cir_rx
[    2.754280] usbcore: registered new interface driver uvcvideo
[    2.760714] USB Video Class driver (1.1.1)
[    2.765265] sunxi cedar version 1.1
[    2.769354] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[    2.775642] VE: sunxi_cedar_probe power-domain init!!!
[    2.781377] VE: install start!!!
[    2.781377]
[    2.786888] VE: cedar-ve the get irq is 41
[    2.786888]
[    2.793317] VE: ve_debug_proc_info:f8905470, data:504b4a6a, lock:a5e0922f
[    2.793317]
[    2.802539] VE: install end!!!
[    2.802539]
[    2.807575] VE: sunxi_cedar_probe
[    2.812569] sunxi-wdt 20500a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    2.821717] Bluetooth: HCI UART driver ver 2.3
[    2.826664] Bluetooth: HCI UART protocol H4 registered
[    2.832651] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[    2.839884] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1
[    2.846216] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1
[    2.852755] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled!
[    2.852755]
[    2.861446] [XR_BT_LPM] bluesleep_probe: uart_index(1)
[    2.870319] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    2.880189] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[    2.886370] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[    2.892686] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[    2.899096] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[    2.905496] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[    2.911997] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[    2.918495] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[    2.924998] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[    2.931976] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[    2.937373] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[    2.944007] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.955107] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[    2.975199] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    2.998158] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[    3.003823] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.008572] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.25 2022-6-21 13:40)
[    3.018510] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.025190] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[    3.038799] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.042644] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[    3.057116] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.060429] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[    3.078344] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[    3.084738] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[    3.091235] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[    3.093911] mmc0: host does not support reading read-only switch, assuming write-enable
[    3.097729] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[    3.108516] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    3.113123] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[    3.124616] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    3.131041] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[    3.142835] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[    3.152100] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.163059] mmc0: new high speed SDHC card at address 1234
[    3.174130] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[    3.181280] mmcblk0: mmc0:1234 SA08G 7.21 GiB
[    3.196364]  mmcblk0: p1 p2 p3 p4 p5 p6 p7
[    3.198008] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.225143] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[    3.232697] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.238634] usbcore: registered new interface driver usbhid
[    3.250574] usbhid: USB HID core driver
[    3.251723] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    3.254878] exFAT: Version 1.3.0
[    3.269977] sunxi-mmc 4021000.sdmmc: card claims to support voltages below defined range
[    3.279487] sunxi-msgbox 3003000.msgbox: sunxi msgbox driver probe ...
[    3.287041] sunxi-msgbox 3003000.msgbox: sunxi msgbox driver init ok...
[    3.295044] sunxi-rproc 3000008.dsp_rproc: sunxi rproc driver 2.1.2
[    3.302065] sunxi-rproc 3000008.dsp_rproc: failed to get firmware-name
[    3.309820] remoteproc remoteproc0: dsp_rproc is available
[    3.316000] sunxi-rproc 3000008.dsp_rproc: sunxi rproc driver probe ok
[    3.324102] sunxi-rpbuf-controller rpbuf_controller@0: assigned reserved memory node dsp0_rpbuf@42244000
[    3.334958] sunxi-rpbuf-controller rpbuf_controller@0: rpbuf_register_ctrl_dev:827
[    3.347010] sun8iw20-pinctrl 2000000.pinctrl: unsupported function i2s0 on pin PE14
[    3.355650] sun8iw20-pinctrl 2000000.pinctrl: unsupported function i2s0 on pin PE13
[    3.364643] sunxi-daudio 2032000.daudio: regulator missing or invalid
[    3.372221] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    3.372443] [AUDIOCODEC][sunxi_codec_parse_params][2437]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1
[    3.372443]
[    3.383859] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[    3.400834] [AUDIOCODEC][sunxi_codec_parse_params][2473]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[    3.423287] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[    3.423720] [AUDIOCODEC][sunxi_internal_codec_probe][2634]:codec probe finished
[    3.443934] mmc1: new high speed SDIO card at address 0001
[    3.444535] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[    3.459873] [SNDCODEC][sunxi_card_init][583]:card init finished
[    3.466961] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[    3.477907] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1
[    3.489949] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
[    3.497900] NET: Registered protocol family 17
[    3.503063] Bluetooth: RFCOMM TTY layer initialized
[    3.508596] Bluetooth: RFCOMM socket layer initialized
[    3.514333] Bluetooth: RFCOMM ver 1.11
[    3.517958] [SNDCODEC][sunxi_hs_init_work][259]:resume-->report switch
[    3.519246] Registering SWP/SWPB emulation handler
[    3.545367] sunxi-i2c 2502800.twi: 2502800.twi supply twi not found, using dummy regulator
[    3.555618] sunxi-i2c 2502800.twi: probe success
[    3.562143] sunxi-thermal 2009400.ths: sun8iw20 cp version:17
[    3.598861] sunxi-audio-card 20320a0.sounddaudio0: use dummy codec for simple card.
[    3.607599] debugfs: Directory '2032000.daudio' with parent 'snddaudio0' already present!
[    3.617261] sunxi-audio-card 20320a0.sounddaudio0: snd-soc-dummy-dai <-> 2032000.daudio mapping ok
[    3.628210] sun8iw20-pinctrl 2000000.pinctrl: pin PE13 already requested by 2502800.twi; cannot claim for 2032000.daudio
[    3.640446] sun8iw20-pinctrl 2000000.pinctrl: pin-141 (2032000.daudio) status -22
[    3.648855] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 141 (PE13) from group PE13  on device 2000000.pinctrl
[    3.661151] sunxi-daudio 2032000.daudio: Error applying setting, reverse things back
[    3.669873] sunxi-daudio 2032000.daudio: failed to activate pinctrl state sleep
[    3.678688] get drvvbus-en is fail, 22
[    3.682896] get ehci0-controller wakeup-source is fail.
[    3.688875] sunxi ehci0-controller don't init wakeup source
[    3.695128] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xc0c695a0, 0x:c88b7000, irq_no:39
[    3.707134] [sunxi-ehci0]: Not init ehci0
[    3.711998] get drvvbus-en is fail, 22
[    3.716205] get ohci0-controller wakeup-source is fail.
[    3.722177] sunxi ohci0-controller don't init wakeup source
[    3.728448] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xc0c69850
[    3.738113] [sunxi-ohci0]: Not init ohci0
[    3.742955] get drvvbus-en is fail, 22
[    3.747159] get ehci1-controller wakeup-source is fail.
[    3.753126] sunxi ehci1-controller don't init wakeup source
[    3.759400] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xc0c69b00, 0x:c88c1000, irq_no:3b
[    3.771677] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[    3.785161] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[    3.792457] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[    3.802396] sunxi-ehci 4200000.ehci1-controller: irq 59, io mem 0x04200000
[    3.837952] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[    3.846613] hub 1-0:1.0: USB hub found
[    3.850898] hub 1-0:1.0: 1 port detected
[    3.856098] get drvvbus-en is fail, 22
[    3.860331] get ohci1-controller wakeup-source is fail.
[    3.866306] sunxi ohci1-controller don't init wakeup source
[    3.872573] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xc0c69db0
[    3.882477] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[    3.894805] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[    3.902076] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[    3.911983] sunxi-ohci 4200400.ohci1-controller: irq 60, io mem 0x04200400
[    3.992756] hub 2-0:1.0: USB hub found
[    3.997003] hub 2-0:1.0: 1 port detected
[    4.003428] otg manager soc@3000000:usbc0@0: soc@3000000:usbc0@0 supply usbc not found, using dummy regulator
[    4.017455] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    4.018011] clk: Not disabling unused clocks
[    4.027160] cfg80211: failed to load regulatory.db
[    4.037432] ALSA device list:
[    4.040828]   #0: audiocodec
[    4.044083]   #1: snddaudio0
[    4.047316] alloc_fd: slot 0 not NULL!
[    4.056126] [EXFAT] trying to mount...
[    4.060952] VFS: Cannot open root device "mmcblk0p5" or unknown-block(179,5): error -5
[    4.069858] Please append a correct "root=" boot option; here are the available partitions:
[    4.079244] b300         7563264 mmcblk0
[    4.079248]  driver: mmcblk
[    4.086865]   b301           17136 mmcblk0p1 a0085546-4166-744a-a353-fca9272b8e45
[    4.086867]
[    4.096954]   b302            1008 mmcblk0p2 a0085546-4166-744a-a353-fca9272b8e46
[    4.096956]
[    4.107025]   b303            1008 mmcblk0p3 a0085546-4166-744a-a353-fca9272b8e47
[    4.107027]
[    4.117188]   b304           12600 mmcblk0p4 a0085546-4166-744a-a353-fca9272b8e48
[    4.117190]
[    4.127266]   b305           53676 mmcblk0p5 a0085546-4166-744a-a353-fca9272b8e49
[    4.127267]
[    4.137344]   b306            1008 mmcblk0p6 a0085546-4166-744a-a353-fca9272b8e4a
[    4.137346]
[    4.147411]   b307         7455072 mmcblk0p7 a0085546-4166-744a-a353-fca9272b8e4b
[    4.147413]
[    4.157480] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,5)
[    4.166948] CPU1: stopping
[    4.169983] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.4.61 #1
[    4.176617] Hardware name: Generic DT based system
[    4.182009] [<c010e364>] (unwind_backtrace) from [<c010a908>] (show_stack+0x10/0x14)
[    4.190698] [<c010a908>] (show_stack) from [<c06bde24>] (dump_stack+0x88/0xa4)
[    4.198802] [<c06bde24>] (dump_stack) from [<c010c700>] (handle_IPI+0xd4/0x180)
[    4.207003] [<c010c700>] (handle_IPI) from [<c035fb90>] (gic_handle_irq+0x70/0x78)
[    4.215497] [<c035fb90>] (gic_handle_irq) from [<c01021cc>] (__irq_svc+0x6c/0xa8)
[    4.223886] Exception stack(0xc7065f80 to 0xc7065fc8)
[    4.229552] 5f80: 000280ec c76c64f4 00000000 c0114cc0 00000002 c7064000 c0b03de8 c0b03e24
[    4.238725] 5fa0: 4000406a 410fc075 00000000 00000000 00000000 c7065fd0 c0108030 c0108034
[    4.247893] 5fc0: 60000113 ffffffff
[    4.251808] [<c01021cc>] (__irq_svc) from [<c0108034>] (arch_cpu_idle+0x2c/0x38)
[    4.260106] [<c0108034>] (arch_cpu_idle) from [<c013def4>] (do_idle+0xbc/0x128)
[    4.268306] [<c013def4>] (do_idle) from [<c013e1f8>] (cpu_startup_entry+0x18/0x20)
[    4.276798] [<c013e1f8>] (cpu_startup_entry) from [<40102bcc>] (0x40102bcc)
[    4.284616] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,5) ]---