Buffalo WZR-HP-G301NH DDWRT boot log

Buffalo WZR-HP-G301NH DDWRT boot.log

BUFFALO U-BOOT Ver 1.07
AP83-208 (ar9100) U-boot 0.0.12
64 MB
Memory Test (address line)
Memory Test start(0x00000000) end(0x04000000) size(67108864)
Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA 
Address line test start:0x00000000 len:0x4000000 pattern 0xAAAAAAAA 0x55555555  
Fill test patnum:5 
fill Pattern 5555AAAA  Writing...             Reading...
fill Pattern AAAA5555  Writing...             Reading...
fill Pattern 0000FFFF  Writing...             Reading...
fill Pattern FFFF0000  Writing...             Reading...
fill Pattern AAAAAAAA  Writing...             Reading...
Top of RAM usable for U-Boot at: 84000000
Reserving 275k for U-Boot at: 83fb8000
Reserving 256k for malloc() at: 83f78000
Reserving 44 Bytes for Board Info at: 83f77fd4
Reserving 36 Bytes for Global Data at: 83f77fb0
Reserving 128k for boot params() at: 83f57fb0
Stack Pointer at: 83f57f98
Now running in RAM - U-Boot at: 83fb8000
Dev ID2:2222
Dev ID3:2201
Name: AMD-SPANSION Flash id: 0x1227E, Size: 33554432 bytes.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Memory Test
uboot use  83F57FB0 - 84000000
Memory Test start(80000000) end(83F00000) size(03F00000)
Pattern 55555555  Writing...            Reading...Pattern AAAAAAAA  Writing...            Reading...Pattern 00000000  Writing...            Reading...
Memory Test OK
### buf_ver=[1.07] U-Boot Ver.=[1.07]
### build_date(env)=[Dec 21 2009 - 10:37:30] build_date(bin)=[Dec 21 2009 - 10:37:30]
ag7100_enet_initialize...
: cfg1 0xf cfg2 0x7114
RTL8366 series driver, reading model-id...
  ID:0x5937, REV:0x0
rtl8366rb_phy_setup  ethUnit=0
Realtek 8366RB switch ID:0x5937 REV:0x3
Realtek Greeen Ethernet Setup
eth0: 02:aa:bb:cc:dd:1a
eth0 up
: cfg1 0x7 cfg2 0x7114
RTL8366 series driver, reading model-id...
eth1: 02:aa:bb:cc:dd:1a
eth1 up
eth0  02:AA:BB:CC:DD:1A
, eth1  02:AA:BB:CC:DD:1A

Trying eth0
eth0 is duplex
ag7100_check_link: _100BASET
dup 1 speed 100
CFG_PLL_FREQ=5
CFG_HZ=bebc200
cpu pll=1050
eth pll=1032
eth0 clk pll=13000a44
eth0 mii=12
eth0 cfg1=f
eth0 cfg2=7115
eth0 fcfg_0=1d1f00
eth0 fcfg_1=7ff0000
eth0 fcfg_2=fff
eth0 fcfg_3=780008
eth0 fcfg_4=3ffff
eth0 fcfg_5=3ffff

tftp server(receive) go, waiting:4[sec]
Trying eth1
eth1 link down
FAIL
Trying eth0
eth0 is duplex
ag7100_check_link: _100BASET
Load address: 0x81f00000

TftpServer Timeout;
no file was loaded.
## Booting image at be060000 ...
   Image Name:   MIPS Linux Kernel Image
   Created:      2018-03-25  23:39:55 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1232592 Bytes =  1.2 MB
   Load Address: 80060000
   Entry Point:  800646d0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 800646d0) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

[    0.000000] Linux version 3.10.108-dd (root@linux) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6438-46177a850f) ) #52300 Mon Mar 26 01:38:48 CEST 2018
[    0.000000] flash_size passed from bootloader = 32
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] booting platform Atheros AR9132 rev 2 (0xb9)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 60812k/65536k available (2694k kernel code, 4724k reserved, 627k data, 196k init, 0k highmem)
[    0.000000] NR_IRQS:83
[    0.000000] irq init done
[    0.000000] plat_time_init: plat time init done
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.120000] bio: create slab <bio-0> at 0
[    0.130000] SCSI subsystem initialized
[    0.130000] usbcore: registered new interface driver usbfs
[    0.140000] usbcore: registered new interface driver hub
[    0.140000] usbcore: registered new device driver usb
[    0.150000] Switching to clocksource MIPS
[    0.150000] NET: Registered protocol family 2
[    0.160000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.160000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.170000] TCP: Hash tables configured (established 512 bind 512)
[    0.170000] TCP: reno registered
[    0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.190000] NET: Registered protocol family 1
[    0.190000] gpio_proc: module loaded and /proc/gpio/ created
[    0.200000] Register LED Device
[    0.200000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[    0.210000] AR7100 GPIOC major 0
[    0.210000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.220000] msgmni has been set to 118
[    0.230000] io scheduler noop registered
[    0.230000] io scheduler deadline registered (default)
[    0.230000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.260000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
[    0.270000] console [ttyS0] enabled, bootconsole disabled
[    0.270000] console [ttyS0] enabled, bootconsole disabled
[    0.280000] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.310000] FLASH ID: AMD-SPANSION SIZE: (32 MB)
[    0.310000] scanning for root partition
[    0.320000] 
[    0.320000] found squashfs at 18D000
[    0.320000] Creating 7 MTD partitions on "ar9100-nor0":
[    0.330000] 0x000000000000-0x000000060000 : "RedBoot"
[    0.330000] 0x000000060000-0x000001fc0000 : "linux"
[    0.340000] 0x00000018d000-0x000001c60000 : "rootfs"
[    0.350000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.360000] mtd: partition "rootfs" set to be root filesystem
[    0.370000] 0x000001c60000-0x000001fc0000 : "ddwrt"
[    0.370000] 0x000001fc0000-0x000001fe0000 : "nvram"
[    0.380000] 0x000001fe0000-0x000002000000 : "board_config"
[    0.390000] 0x000000000000-0x000002000000 : "fullflash"
[    0.390000] tun: Universal TUN/TAP device driver, 1.6
[    0.400000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.410000] Found an RTL8366RB switch
[    0.410000] Realtek RTL8366RB ethernet switch driver version 0.2.4
[    0.420000] rtl8366rb rtl8366rb: using GPIO pins 19 (SDA) and 20 (SCK)
[    0.420000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[    0.490000] libphy: rtl8366rb: probed
[    0.890000] PPP generic driver version 2.4.2
[    0.900000] PPP BSD Compression module registered
[    0.900000] PPP Deflate Compression module registered
[    0.910000] PPP MPPE Compression module registered
[    0.910000] NET: Registered protocol family 24
[    0.920000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.950000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
[    0.960000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
[    1.000000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
[    1.020000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
[    1.020000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.030000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.040000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
[    1.040000] usb usb1: Manufacturer: Linux 3.10.108-dd ehci_hcd
[    1.050000] usb usb1: SerialNumber: platform
[    1.050000] hub 1-0:1.0: USB hub found
[    1.060000] hub 1-0:1.0: 1 port detected
[    1.060000] usbcore: registered new interface driver usb-storage
[    1.080000] GACT probability NOT on
[    1.080000] Mirror/redirect action on
[    1.080000] Failed to load ipt action
[    1.090000] Simple TC action Loaded
[    1.090000] u32 classifier
[    1.090000]     Performance counters on
[    1.100000]     input device check on
[    1.100000]     Actions configured
[    1.110000] Netfilter messages via NETLINK v0.30.
[    1.110000] nf_conntrack version 0.5.0 (950 buckets, 3800 max)
[    1.120000] nf_conntrack_rtsp v0.7 loading
[    1.120000] xt_time: kernel timezone is -0000
[    1.130000] nf_nat_rtsp v0.7 loading
[    1.130000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.140000] TCP: bic registered
[    1.140000] TCP: cubic registered
[    1.140000] TCP: westwood registered
[    1.150000] TCP: highspeed registered
[    1.150000] TCP: hybla registered
[    1.150000] TCP: htcp registered
[    1.160000] TCP: vegas registered
[    1.160000] TCP: veno registered
[    1.160000] TCP: scalable registered
[    1.170000] TCP: lp registered
[    1.170000] TCP: yeah registered
[    1.170000] TCP: illinois registered
[    1.180000] NET: Registered protocol family 17
[    1.180000] NET: Registered protocol family 15
[    1.180000] Bridge firewalling registered
[    1.190000] 8021q: 802.1Q VLAN Support v1.8
[    1.190000] searching for nvram
[    1.200000] nvram size = 0
[    1.220000] Atheros AR71xx hardware watchdog driver version 0.1.0
[    1.230000] ar71xx-wdt: timeout=15 secs (max=21) ref freq=200000000
[    1.240000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.250000] Freeing unused kernel memory: 196K
start service
starting Architecture code for ap83
cannot open /dev/nvram
cannot open /dev/nvram
udevtrigger[285]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
load ag71xx or ag7100_mod Ethernet Driver
[    4.810000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    5.130000] ag71xx ag71xx.1: connected to PHY at rtl8366rb:04 [uid=001cc961, driver=Generic PHY]
[    5.140000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
Failed to connect to the switch. Use the "list" command to see which switches are available.
Failed to connect to the switch. Use the "list" command to see which switches are available.
Failed to connect to the switch. Use the "list" command to see which switches are available.
configure eth0 to 00:24:a5:b0:58:e4
configure eth1 to 00:24:a5:b0:58:e4
[    5.280000] eth0: link up (1000Mbps/Full duplex)
load ATH 802.11 a/b/g Driver
insmod: ath_pci.ko: module not found
insmod: ath_ahb.ko: module not found
load ATH9K 802.11n Driver
[    5.510000] lzma_compress: module license 'unspecified' taints kernel.
[    5.520000] Disabling lock debugging due to kernel taint
[    5.600000] Loading modules backported from Linux version wireless-drivers-next-for-davem-2017-09-01-0-geb464d4a8d09
[    5.620000] Backport generated by backports.git backports-20160324-111-g97b8d7c4
[    6.460000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
interface wlan0 does not exist!
[USB] checking...
umount: can't unmount /mnt: No such file or directory
cannot open /proc/sys/net/ipv4/ip_conntrack_max
cannot open /proc/sys/net/ipv4/ip_conntrack_max
ath9k deconfigure_single: phy0 ath0
[    8.830000] device br0 entered promiscuous mode
killall: ead: no process killed
[    8.890000] eth0: link down
[    8.910000] eth0: link up (1000Mbps/Full duplex)
[    8.920000] eth0: link down
[    8.940000] eth0: link up (1000Mbps/Full duplex)
[    8.950000] device eth0 entered promiscuous mode
sh: ead: not found
[    8.960000] br0: port 1(eth0) entered forwarding state
[    8.960000] br0: port 1(eth0) entered forwarding state
[    8.970000] device br0 left promiscuous mode
[    8.980000] device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Address not available
[    9.000000] device br0 left promiscuous mode
ath9k deconfigure_single: phy0 ath0
[   10.960000] br0: port 1(eth0) entered forwarding state
ath9k configure_single: phy0 ath0
call mac80211autochannel for interface: ath0
ath0: freq:2412 qual:77 noise:-94 eirp: 21
ath0: freq:2432 qual:77 noise:-94 eirp: 21
ath0: freq:2422 qual:70 noise:-94 eirp: 21
ath0: freq:2462 qual:55 noise:-94 eirp: 21
ath0: freq:2427 qual:45 noise:-94 eirp: 21
ath0: freq:2417 qual:44 noise:-94 eirp: 21
ath0: freq:2452 qual:44 noise:-94 eirp: 21
ath0: freq:2442 qual:42 noise:-93 eirp: 21
ath0: freq:2437 qual:30 noise:-95 eirp: 21
ath0: freq:2447 qual:29 noise:-93 eirp: 21
ath0: freq:2457 qual:28 noise:-94 eirp: 21
mac80211autochannel interface: ath0 frequency: 2412
setup ath0 00:24:A5:B0:58:E4
Configuration file: /tmp/ath0_hostap.conf
ath0: interface state UNINITIALIZED->COUNTRY_UPDATE
Using interface ath0 with hwaddr 00:24:a5:b0:58:e4 and ssid "dd-wrt"
ath0: interface state COUNTRY_UPDATE->ENABLED
ath0: AP-ENABLED 
[   16.950000] device ath0 entered promiscuous mode
[   16.960000] br0: port 2(ath0) entered forwarding state
[   16.960000] br0: port 2(ath0) entered forwarding state
killall: roaming_daemon: no process killed
[   17.640000] device eth1 entered promiscuous mode
cp: can't stat '/tmp/mycron.d/*': No such file or directory
cp: can't stat '/jffs/mycron.d/*': No such file or directory
[   17.990000] fast-classifier: starting up
[   17.990000] fast-classifier: registered
cp: can't stat '/mmc/mycron.d/*': No such file or directory
cat: can't open '/proc/sys/net/netfilter/nf_conntrack_flush': No such file or directory
[   18.960000] br0: port 2(ath0) entered forwarding state
[   19.210000] device eth1 left promiscuous mode
udhcpc: started, v1.28.1
ath9k radio 0: phy0 ath0
cannot open /proc/sys/dev/wifi0/silent
cannot open /proc/sys/dev/wifi0/ledon
ath9k radio 1: phy0 ath0
cannot open /proc/sys/dev/wifi0/silent
udhcpc: sending discover
/opt/etc/init.d/rcS: No such file or directory
/jffs/etc/init.d/rcS: No such file or directory
/mmc/etc/init.d/rcS: No such file or directory
rmmod: eoip: No such file or directory
killall: proxywatchdog.sh: no process killed
/mnt/smbshare
umount: can't unmount /mnt/smbshare: No such file or directory
rmmod: cifs: No such file or directory
rmmod: fscache: No such file or directory
killall: schedulerb.sh: no process killed
killall: shatd: no process killed
killall: wdswatchdog.sh: no process killed
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
Empty.
udhcpc: sending discover
udhcpc: sending discover

DD-WRT v3.0-r35531 std (c) 2018 NewMedia-NET GmbH
Release: 03/26/18

DD-WRT login: