Skip to content

Instantly share code, notes, and snippets.

@razum2um

razum2um/dmesg.patch Secret

Last active June 4, 2019 22:45
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save razum2um/8e2bfbcffdcdb3a832a4862339330867 to your computer and use it in GitHub Desktop.
Save razum2um/8e2bfbcffdcdb3a832a4862339330867 to your computer and use it in GitHub Desktop.
Download ZIP
Raw
readme.md

NanoPi M4

Reports

Report for default-desktop:

BOOT=yes
VERSION=5.85
KERNEL=4.4.178-rk3399
NETWORK=yes
WIRELESS=wifi yes; bluetooth not sure: installed, but didn't find any peers available
HDMI=yes
USB=yes
DVFS=not sure how to check

Report for dev-server (5.87):

BOOT=yes
VERSION=5.87
KERNEL=5.0.0-rk3399
NETWORK=yes
WIRELESS=no
HDMI=yes
USB=yes
DVFS=not sure how to check

Report for custom dev-server (5.90, my version):

BOOT=yes
VERSION=5.90
KERNEL=5.1.0-rk3399
NETWORK=yes
WIRELESS=no
HDMI=yes
USB=yes
DVFS=not sure how to check

I tried to update kernel to ayufan-rock64/linux-mainline-kernel master

Build diff is here

Mainstream has changed rockchip arch/arm64/boot/dts/rockchip/* layout a bit, find rk3399-nanopi-m4 here instead of rk3399-nanopi4-rev01.

I don't have any UART converter, so I just reduced the number of patches to dbs until I could blindly boot :)

Wifi on 5.x

I'm trying to get wifi working. No wlan0 is listed in iwconfig/ifconfig etc.

Below are essential diffs of dmesg and lsmod from 4.4 to 5.1 (note: 5.0 aka dev-server, nightly atm, works the same)

I also ensured that rtl8812au module mentioned here compiles and loads.

On default 4.4 I see this

# readlink /sys/class/net/wlan0/device/driver
../../../../../../../bus/sdio/drivers/bcmsdh_sdmmc

# cat /sys/class/net/wlan0/device/modalias
sdio:c00v02D0d4356

at this point I'm even not sure what's missing (module? firmware?) in 5.x

Any help appreciated :)

Raw
dmesg.patch
--- /mnt/diff/dmesg/dmesg-4.4.no-times 2019-06-05 04:01:41.638923396 +0700
+++ /mnt/diff/dmesg/dmesg-5.1.0-90-no-times 2019-06-05 04:02:03.970725931 +0700
@@ -1,1349 +1,526 @@
- Booting Linux on physical CPU 0x0
- Initializing cgroup subsys cpuset
- Initializing cgroup subsys cpu
- Initializing cgroup subsys cpuacct
- (Linaro GCC 7.4-2019.02) ) #2 SMP Wed May 8 17:01:36 CEST 2019
- Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
+ (Linaro GCC 7.4-2019.02)) #5.90 SMP Tue Jun 4 19:42:56 UTC 2019
+ Machine model: FriendlyElec NanoPi M4
+ efi: Getting EFI parameters from FDT:
+ efi: UEFI not found.
+ cma: Reserved 16 MiB at 0x00000000f7000000
+ NUMA: No NUMA configuration found
+
+
+ Zone ranges:
+
+ Normal empty
+ Movable zone start for each node
+ Early memory node ranges
+
+
On node 0 totalpages: 1015296
- DMA zone: 15864 pages used for memmap
- DMA zone: 0 pages reserved
- DMA zone: 1015296 pages, LIFO batch:31
+ DMA32 zone: 15864 pages used for memmap
+ DMA32 zone: 0 pages reserved
+ DMA32 zone: 1015296 pages, LIFO batch:63
psci: probing for conduit method from DT.
psci: PSCIv1.0 detected in firmware.
psci: Using standard PSCI v0.2 function IDs
psci: MIGRATE_INFO_TYPE not supported.
- PERCPU: Embedded 21 pages/cpu @ffffffc0f7ed0000 s46312 r8192 d31512 u86016
- pcpu-alloc: s46312 r8192 d31512 u86016 alloc=21*4096
+ psci: SMC Calling Convention v1.0
+ random: get_random_bytes called from start_kernel+0xa4/0x448 with crng_init=0
+ percpu: Embedded 23 pages/cpu s55320 r8192 d30696 u94208
+ pcpu-alloc: s55320 r8192 d30696 u94208 alloc=23*4096
5
Detected VIPT I-cache on CPU0
- CPU features: enabling workaround for ARM erratum 845719
- Built 1 zonelists in Zone order, mobility grouping on. Total pages: 999432
- Kernel command line: root=UUID=777e488f-13d0-40a2-b5af-a8739223ddec rootwait rootfstype=ext4 console=tty1 console=ttyS2,1500000 panic=10 consoleblank=0 loglevel=1 ubootpart=fc44b011-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
- PID hash table entries: 4096 (order: 3, 32768 bytes)
- Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
- Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
- (64MB)
- Memory: 3892700K/4061184K available (12798K kernel code, 1660K rwdata, 4340K rodata, 1216K init, 767K bss, 168484K reserved, 0K cma-reserved)
- Virtual kernel memory layout:
- modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
- vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB)
- .init : 0xffffff8009150000 - 0xffffff8009280000 ( 1216 KB)
- .text : 0xffffff8008080000 - 0xffffff8008d00000 ( 12800 KB)
- .rodata : 0xffffff8008d00000 - 0xffffff8009150000 ( 4416 KB)
- .data : 0xffffff8009280000 - 0xffffff800941f008 ( 1661 KB)
- vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
- 0xffffffbdc0008000 - 0xffffffbdc3e00000 ( 61 MB actual)
- fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 KB)
- PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB)
- memory : 0xffffffc000200000 - 0xffffffc0f8000000 ( 3966 MB)
+ CPU features: detected: GIC system register CPU interface
+ Built 1 zonelists, mobility grouping on. Total pages: 999432
+ Policy zone: DMA32
+ Kernel command line: root=UUID=74450e17-e86d-4f14-9288-0c1091871024 rootwait rootfstype=ext4 console=ttyS2,1500000 console=tty1 panic=10 consoleblank=0 loglevel=1 ubootpart=f458fa66-01 usb-storage.quirks= cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1
+ Memory: 3945872K/4061184K available (9852K kernel code, 660K rwdata, 2544K rodata, 960K init, 348K bss, 98928K reserved, 16384K cma-reserved)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
- Hierarchical RCU implementation.
- Build-time adjustment of leaf fanout to 64.
- RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
- RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
- NR_IRQS:64 nr_irqs:64 0
- GIC: Using split EOI/Deactivate mode
- ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
- ITS: allocated 65536 Devices @ee900000 (psz 64K, shr 0)
+ rcu: Hierarchical RCU implementation.
+ rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
+ rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
+ rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
+ NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
+ GICv3: GIC: Using split EOI/Deactivate mode
+ GICv3: Distributor has no Range Selector support
+ GICv3: no VLPI support, no direct LPI support
+ GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
+
+ ITS@0x00000000fee20000: allocated 65536 Devices @f6080000 (flat, esz 8, psz 64K, shr 0)
ITS: using cache flushing for cmd queue
- GIC: using LPI property table @0x00000000ee890000
- ITS: Allocated 1792 chunks for LPIs
- CPU0: found redistributor 0 region 0:0x00000000fef00000
- CPU0: using LPI pending table @0x00000000ee8a0000
+ GICv3: using LPI property table @0x00000000f6040000
GIC: using cache flushing for LPI property table
+ GICv3: CPU0: using allocated LPI pending table @0x00000000f6050000
}
}
rockchip_mmc_get_phase: invalid clk rate
rockchip_mmc_get_phase: invalid clk rate
rockchip_mmc_get_phase: invalid clk rate
rockchip_mmc_get_phase: invalid clk rate
- rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
- rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
- Architected cp15 timer(s) running at 24.00MHz (phys).
+ arch_timer: cp15 timer(s) running at 24.00MHz (phys).
clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
Console: colour dummy device 80x25
enabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
pid_max: default: 32768 minimum: 301
- Security Framework initialized
- Yama: becoming mindful.
- AppArmor: AppArmor disabled by boot time parameter
+ LSM: Security Framework initializing
+ Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
+ Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
- Initializing cgroup subsys io
- Initializing cgroup subsys memory
- Initializing cgroup subsys devices
- Initializing cgroup subsys freezer
- Initializing cgroup subsys net_cls
- Initializing cgroup subsys perf_event
- Initializing cgroup subsys net_prio
- Initializing cgroup subsys hugetlb
- Initializing cgroup subsys pids
- ftrace: allocating 44962 entries in 176 pages
- sched-energy: Sched-energy-costs installed from DT
- CPU0: update cpu_capacity 401
+ *** VALIDATE proc ***
+ *** VALIDATE cgroup1 ***
+ *** VALIDATE cgroup2 ***
ASID allocator initialised with 32768 entries
+ rcu: Hierarchical SRCU implementation.
+ Platform MSI: interrupt-controller@fee20000 domain created
PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
- Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
+ EFI services will not be available.
+ smp: Bringing up secondary CPUs ...
Detected VIPT I-cache on CPU1
- CPU1: found redistributor 1 region 0:0x00000000fef20000
- CPU1: using LPI pending table @0x00000000eeb40000
- CPU1: update cpu_capacity 401
+ GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
+ GICv3: CPU1: using allocated LPI pending table @0x00000000f6060000
Detected VIPT I-cache on CPU2
- CPU2: found redistributor 2 region 0:0x00000000fef40000
- CPU2: using LPI pending table @0x00000000eeb60000
- CPU2: update cpu_capacity 401
+ GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
+ GICv3: CPU2: using allocated LPI pending table @0x00000000f6070000
Detected VIPT I-cache on CPU3
- CPU3: found redistributor 3 region 0:0x00000000fef60000
- CPU3: using LPI pending table @0x00000000eebc0000
- CPU3: update cpu_capacity 401
+ GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
+ GICv3: CPU3: using allocated LPI pending table @0x00000000f6100000
+ CPU features: detected: EL2 vector hardening
Detected PIPT I-cache on CPU4
- CPU4: found redistributor 100 region 0:0x00000000fef80000
- CPU4: using LPI pending table @0x00000000eebf0000
- CPU4: update cpu_capacity 1024
+ GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
+ GICv3: CPU4: using allocated LPI pending table @0x00000000f6110000
Detected PIPT I-cache on CPU5
- CPU5: found redistributor 101 region 0:0x00000000fefa0000
- CPU5: using LPI pending table @0x00000000ee030000
- CPU5: update cpu_capacity 1024
+ GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
+ GICv3: CPU5: using allocated LPI pending table @0x00000000f6120000
- Brought up 6 CPUs
+ smp: Brought up 1 node, 6 CPUs
SMP: Total of 6 processors activated.
- CPU features: detected feature: GIC system register CPU interface
+ CPU features: detected: 32-bit EL0 Support
+ CPU features: detected: CRC32 instructions
CPU: All CPU(s) started at EL2
alternatives: patching kernel code
devtmpfs: initialized
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
futex hash table entries: 2048 (order: 5, 131072 bytes)
- xor: measuring software checksum speed
- 8regs : 2874.000 MB/sec
- 8regs_prefetch: 2578.000 MB/sec
- 32regs : 3243.000 MB/sec
- 32regs_prefetch: 2864.000 MB/sec
- xor: using function: 32regs (3243.000 MB/sec)
pinctrl core: initialized pinctrl subsystem
- regulator-dummy: no parameters
+ DMI not present or invalid.
NET: Registered protocol family 16
- cpuidle: using governor ladder
+ audit: initializing netlink subsys (disabled)
+ audit: type=2000 audit(0.228:1): state=initialized audit_enabled=0 res=1
cpuidle: using governor menu
- Registered FIQ tty driver
- vdso: 2 pages (1 code @ ffffff8008d06000, 1 data @ ffffff8009284000)
+ vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
- DMA: preallocated 256 KiB pool for atomic allocations
- gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0
- gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1
- gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2
- gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3
- gpiochip_add_data: registered GPIOs 128 to 159 on device: gpio4
- raid6: int64x1 gen() 473 MB/s
- raid6: int64x1 xor() 417 MB/s
- raid6: int64x2 gen() 655 MB/s
- raid6: int64x2 xor() 602 MB/s
- raid6: int64x4 gen() 969 MB/s
- raid6: int64x4 xor() 666 MB/s
- raid6: int64x8 gen() 756 MB/s
- raid6: int64x8 xor() 628 MB/s
- raid6: neonx1 gen() 994 MB/s
- raid6: neonx1 xor() 671 MB/s
- raid6: neonx2 gen() 1328 MB/s
- raid6: neonx2 xor() 1005 MB/s
- raid6: neonx4 gen() 1794 MB/s
- raid6: neonx4 xor() 1214 MB/s
- raid6: neonx8 gen() 1694 MB/s
- raid6: neonx8 xor() 1269 MB/s
- raid6: using algorithm neonx4 gen() 1794 MB/s
- raid6: .... xor() 1214 MB/s, rmw enabled
- raid6: using intx1 recovery algorithm
-'
- vcc3v3_sys: 3300 mV
- reg-fixed-voltage vcc3v3-sys: vcc3v3_sys supplying 3300000uV
-'
- vcc5v0_host: 5000 mV
- reg-fixed-voltage vcc5v0-host-regulator: vcc5v0_host supplying 5000000uV
-'
- vcc5v0_sys: 5000 mV
- reg-fixed-voltage vcc5v0-sys: vcc5v0_sys supplying 5000000uV
-'
- vcc1v8_sys: 1800 mV
- reg-fixed-voltage vccadc-ref: vcc1v8_sys supplying 1800000uV
-' - status (0)
- vcc_sd: 3000 mV
- reg-fixed-voltage vcc-sd: vcc_sd supplying 3000000uV
-'
- vcc_phy: no parameters
- reg-fixed-voltage vcc-phy-regulator: vcc_phy supplying 0uV
-' - status (0)
- reg-fixed-voltage vcc-lcd: Looking up vin-supply from device tree
- vcc_lcd: supplied by vcc5v0_sys
- vcc5v0_sys: could not add device link regulator.7 err -2
- vcc_lcd: 3300 mV
- reg-fixed-voltage vcc-lcd: vcc_lcd supplying 3300000uV
- iommu: Adding device ff650000.vpu_service to group 0
- iommu: Adding device ff660000.rkvdec to group 1
- iommu: Adding device ff8f0000.vop to group 2
- iommu: Adding device ff900000.vop to group 3
- iommu: Adding device ff910000.cif_isp to group 4
- iommu: Adding device ff920000.cif_isp to group 5
+ DMA: preallocated 2048 KiB pool for atomic allocations
+ Serial: AMBA PL011 UART driver
+ HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
+ HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
+ HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
+ HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
+ cryptd: max_cpu_qlen set to 1000
+ vcc5v0_core: supplied by vdd_5v
+ vcc5v0_sys: supplied by vdd_5v
+ vbus_typec: supplied by vdd_5v
+ vcc5v0_usb1: supplied by vcc5v0_sys
+ vcc3v3_sys: supplied by vcc5v0_core
+ vcc3v0_sd: supplied by vcc3v3_sys
+ vcc5v0_usb2: supplied by vcc5v0_sys
+ vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
- media: Linux media interface: v0.10
- Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
PTP clock support registered
+ EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
- NetLabel: Initializing
- NetLabel: domain hash size = 128
- NetLabel: protocols = UNLABELED CIPSOv4
- NetLabel: unlabeled traffic allowed by default
- rockchip-cpuinfo cpuinfo: Serial : 8e28b0c466558574
clocksource: Switched to clocksource arch_sys_counter
- thermal thermal_zone1: power_allocator: sustainable_power will be estimated
+ VFS: Disk quotas dquot_6.6.0
+ VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
+ *** VALIDATE hugetlbfs ***
NET: Registered protocol family 2
+ tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
- TCP bind hash table entries: 32768 (order: 8, 1048576 bytes)
+ TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
- UDP hash table entries: 2048 (order: 5, 196608 bytes)
- UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes)
+ UDP hash table entries: 2048 (order: 4, 65536 bytes)
+ UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
NET: Registered protocol family 1
+ RPC: Registered named UNIX socket transport module.
+ RPC: Registered udp transport module.
+ RPC: Registered tcp transport module.
+ RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
- Trying to unpack rootfs image as initramfs...
- Freeing initrd memory: 8108K
+ Unpacking initramfs...
+ Freeing initrd memory: 8156K
hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
-: 8-bit VMID
+: IPA Size Limit: 40bits
+: vgic-v2@fff20000
+: GIC system register CPU interface enabled
+: vgic interrupt IRQ10
: Hyp mode initialized successfully
-: interrupt-controller@fff20000 IRQ10
-: timer IRQ12
- audit: initializing netlink subsys (disabled)
- audit: type=2000 audit(1.860:1): initialized
- Initialise system trusted keyring
- HugeTLB registered 2 MB page size, pre-allocated 0 pages
- VFS: Disk quotas dquot_6.6.0
- VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
+ Initialise system trusted keyrings
+ workingset: timestamp_bits=44 max_order=20 bucket_order=0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
- fuse init (API version 7.23)
- JFS: nTxBlock = 8192, nTxLock = 65536
+ NFS: Registering the id_resolver key type
+ Key type id_resolver registered
+ Key type id_legacy registered
+ nfs4filelayout_init: NFSv4 File Layout Driver Registering...
SGI XFS with ACLs, security attributes, realtime, no debug enabled
- Key type big_key registered
-
- TEE Core Framework initialization (ver 1:0.1)
- TEE armv7 Driver initialization
- tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
- TEE core: Alloc the misc device "opteearmtz00" (id=0)
- TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
- NET: Registered protocol family 38
+ 9p: Installing v9fs 9p2000 file system support
Key type asymmetric registered
Asymmetric key parser 'x509' registered
- Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
- io scheduler noop registered
- io scheduler deadline registered (default)
- io scheduler cfq registered
- phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up phy-supply from device tree
- vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e460.0 err -2
- phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply from device tree
- phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed
- phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply from device tree
- phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed
- phy phy-ff770000.syscon:usb2-phy@e460.1: Failed to get VBUS supply regulator
- phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply from device tree
- phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply property in node /syscon@ff770000/phy@f780 failed
- phy phy-ff800000.phy.3: Looking up phy-supply from device tree
- phy phy-ff800000.phy.3: Looking up phy-supply property in node /phy@ff800000/dp-port failed
- phy phy-ff800000.phy.4: Looking up phy-supply from device tree
- phy phy-ff800000.phy.4: Looking up phy-supply property in node /phy@ff800000/usb3-port failed
- phy phy-pcie-phy.5: Looking up phy-supply from device tree
- phy phy-pcie-phy.5: Looking up phy-supply property in node /pcie-phy failed
- rockchip-pcie f8000000.pcie: GPIO lookup for consumer ep
- rockchip-pcie f8000000.pcie: using device tree for GPIO lookup
-' - status (0)
- rockchip-pcie f8000000.pcie: Looking up vpcie3v3-supply from device tree
- rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply from device tree
- rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply property in node /pcie@f8000000 failed
- rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
- rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply from device tree
- rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply property in node /pcie@f8000000 failed
- rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
- rockchip-pcie f8000000.pcie: invalid power supply
- rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
- rockchip-pcie: probe of f8000000.pcie failed with error -110
- pwm-backlight backlight: GPIO lookup for consumer enable
- pwm-backlight backlight: using device tree for GPIO lookup
-' - status (0)
- no flags found for enable
- pwm-backlight backlight: Looking up power-supply from device tree
- pwm-backlight backlight: Looking up power-supply property in node /backlight failed
- backlight supply power not found, using dummy regulator
+ Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
+ io scheduler mq-deadline registered
+ io scheduler kyber registered
+ io scheduler bfq registered
dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
- pwm-regulator vdd-log: GPIO lookup for consumer enable
- pwm-regulator vdd-log: using device tree for GPIO lookup
-'
-'
- pwm-regulator vdd-log: using lookup tables for GPIO lookup
- pwm-regulator vdd-log: lookup for GPIO enable failed
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- vdd_log: 800 <--> 1400 mV at 800 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
- ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 37, base_baud = 1500000) is a 16550A
- disabled
- ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 38, base_baud = 1500000) is a 16550A
+ Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
+ ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 39, base_baud = 1500000) is a 16550A
+ ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 40, base_baud = 1500000) is a 16550A
enabled
- ff370000.serial: ttyS4 at MMIO 0xff370000 (irq = 40, base_baud = 1500000) is a 16550A
- Initialized drm 1.1.0 20060810
- Rockchip DRM driver version: v1.0.1
- rockchip-drm display-subsystem: defer getting devfreq
- rockchip-vop ff900000.vop: missing rockchip,grf property
- rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008da3e08)
- rockchip-vop ff8f0000.vop: missing rockchip,grf property
- rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8008da3e08)
- rockchip-drm display-subsystem: failed to bind ff940000.hdmi (ops 0xffffff8008d9a680): -517
- rockchip-drm display-subsystem: master bind failed: -517
- panel-friendlyelec edp-panel: Looking up power-supply from device tree
- panel-friendlyelec edp-panel: GPIO lookup for consumer enable
- panel-friendlyelec edp-panel: using device tree for GPIO lookup
-'
-'
- panel-friendlyelec edp-panel: using lookup tables for GPIO lookup
- panel-friendlyelec edp-panel: lookup for GPIO enable failed
- Unable to detect cache hierarchy for CPU 0
- brd: module loaded
+ cacheinfo: Unable to detect cache hierarchy for CPU 0
loop: module loaded
- lkdtm: No crash points registered, enable through debugfs
- rk_gmac-dwmac fe300000.ethernet: Looking up phy-supply from device tree
- rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
- rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
- rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
- rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
- rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
- rk_gmac-dwmac fe300000.ethernet: clock input from PHY
- rk_gmac-dwmac fe300000.ethernet: init for RGMII
- stmmac - user ID: 0x10, Synopsys ID: 0x35
- Ring mode enabled
- DMA HW capability register supported
- Normal descriptors
- RX Checksum Offload Engine supported (type 2)
- TX Checksum insertion supported
- Wake-Up On Lan supported
- Enable RX Mitigation via HW Watchdog Timer
-' - status (0)
- libphy: stmmac: probed
- eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
- eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
- usbcore: registered new interface driver rndis_wlan
- Rockchip WiFi SYS interface (V1.00) ...
- usbcore: registered new interface driver cdc_ether
- usbcore: registered new interface driver rndis_host
- rockchip-dwc3 usb0: failed to get drvdata dwc3
- rockchip-dwc3 usb1: fail to get drvdata hcd
+ libphy: Fixed MDIO Bus: probed
+ tun: Universal TUN/TAP device driver, 1.6
+ VFIO - User Level meta-driver version: 0.3
+ dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
+ dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-platform: EHCI generic platform driver
- ehci-platform fe3c0000.usb: EHCI Host Controller
- ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1
- ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
- ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
- usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
+ ehci-platform fe380000.usb: EHCI Host Controller
+ ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
+ ehci-platform fe380000.usb: irq 31, io mem 0xfe380000
+ ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
+ usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
- usb usb1: Manufacturer: Linux 4.4.178-rk3399 ehci_hcd
- usb usb1: SerialNumber: fe3c0000.usb
+ usb usb1: Manufacturer: Linux 5.1.0-rk3399 ehci_hcd
+ usb usb1: SerialNumber: fe380000.usb
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
- ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- ohci-platform: OHCI generic platform driver
- ohci-platform fe3e0000.usb: Generic Platform OHCI controller
- ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2
- ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
- usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
+ ehci-platform fe3c0000.usb: EHCI Host Controller
+ ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 2
+ ehci-platform fe3c0000.usb: irq 33, io mem 0xfe3c0000
+ ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
+ usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb2: Product: Generic Platform OHCI controller
- usb usb2: Manufacturer: Linux 4.4.178-rk3399 ohci_hcd
- usb usb2: SerialNumber: fe3e0000.usb
+ usb usb2: Product: EHCI Host Controller
+ usb usb2: Manufacturer: Linux 5.1.0-rk3399 ehci_hcd
+ usb usb2: SerialNumber: fe3c0000.usb
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
- usbcore: registered new interface driver cdc_acm
- cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
- usbcore: registered new interface driver cdc_wdm
- usbcore: registered new interface driver usbserial
- usbcore: registered new interface driver usbserial_generic
- usbserial: USB Serial support registered for generic
- usbcore: registered new interface driver iforce
- usbcore: registered new interface driver xpad
- usbcore: registered new interface driver usbtouchscreen
+ ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
+ ohci-pci: OHCI PCI platform driver
+ ohci-platform: OHCI generic platform driver
+ ohci-platform fe3a0000.usb: Generic Platform OHCI controller
+ ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3
+ ohci-platform fe3a0000.usb: irq 32, io mem 0xfe3a0000
+ usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.01
+ usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
+ usb usb3: Product: Generic Platform OHCI controller
+ usb usb3: Manufacturer: Linux 5.1.0-rk3399 ohci_hcd
+ usb usb3: SerialNumber: fe3a0000.usb
+ hub 3-0:1.0: USB hub found
+ hub 3-0:1.0: 1 port detected
+ ohci-platform fe3e0000.usb: Generic Platform OHCI controller
+ ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 4
+ ohci-platform fe3e0000.usb: irq 34, io mem 0xfe3e0000
+ usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.01
+ usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
+ usb usb4: Product: Generic Platform OHCI controller
+ usb usb4: Manufacturer: Linux 5.1.0-rk3399 ohci_hcd
+ usb usb4: SerialNumber: fe3e0000.usb
+ hub 4-0:1.0: USB hub found
+ hub 4-0:1.0: 1 port detected
+ usbcore: registered new interface driver usb-storage
i2c /dev entries driver
- fan53555-regulator 0-0040: GPIO lookup for consumer vsel
- fan53555-regulator 0-0040: using device tree for GPIO lookup
-' - status (0)
Detected!
- fan53555-regulator 0-0040: Looking up vin-supply from device tree
fan53555-reg: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.9 err -2
- vdd_cpu_b: 712 <--> 1500 mV at 1000 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- fan53555-regulator 0-0041: GPIO lookup for consumer vsel
- fan53555-regulator 0-0041: using device tree for GPIO lookup
-' - status (0)
Detected!
- fan53555-regulator 0-0041: Looking up vin-supply from device tree
fan53555-reg: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.10 err -2
- vdd_gpu: 712 <--> 1500 mV at 1000 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Pmic Chip id: 0x0
- rk808 0-001b: GPIO lookup for consumer dvs
- rk808 0-001b: using device tree for GPIO lookup
-'
-'
- rk808 0-001b: using lookup tables for GPIO lookup
- rk808 0-001b: lookup for GPIO dvs failed
+ rk808 0-001b: chip id: 0x0
rk808-regulator rk808-regulator: there is no dvs0 gpio
- rk808 0-001b: GPIO lookup for consumer dvs
- rk808 0-001b: using device tree for GPIO lookup
-'
-'
- rk808 0-001b: using lookup tables for GPIO lookup
- rk808 0-001b: lookup for GPIO dvs failed
rk808-regulator rk808-regulator: there is no dvs1 gpio
- rk808 0-001b: Looking up vcc1-supply from device tree
DCDC_REG1: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.11 err -2
- vdd_center: 750 <--> 1350 mV at 900 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc2-supply from device tree
DCDC_REG2: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.12 err -2
- vdd_cpu_l: 750 <--> 1350 mV at 900 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc3-supply from device tree
DCDC_REG3: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.13 err -2
- vcc_ddr: at 3300 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc4-supply from device tree
DCDC_REG4: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.14 err -2
- vcc_1v8: 1800 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc6-supply from device tree
LDO_REG1: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.15 err -2
- vcc1v8_dvp: 1800 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc6-supply from device tree
LDO_REG2: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.16 err -2
- vcc3v0_tp: Bringing 1800000uV into 3000000-3000000uV
- vcc3v0_tp: ramp_delay not set
- vcc3v0_tp: 3000 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc7-supply from device tree
+ vcc3v0_touch: Bringing 1800000uV into 3000000-3000000uV
LDO_REG3: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.17 err -2
- vcc1v8_pmu: 1800 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc9-supply from device tree
LDO_REG4: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.18 err -2
- vccio_sd: 1800 <--> 3000 mV at 3000 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc9-supply from device tree
LDO_REG5: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.19 err -2
vcca3v0_codec: Bringing 1800000uV into 3000000-3000000uV
- vcca3v0_codec: ramp_delay not set
- vcca3v0_codec: 3000 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc10-supply from device tree
LDO_REG6: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.20 err -2
- vcc_1v5: 1500 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc7-supply from device tree
LDO_REG7: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.21 err -2
vcca1v8_codec: Bringing 800000uV into 1800000-1800000uV
- vcca1v8_codec: ramp_delay not set
- vcca1v8_codec: 1800 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc11-supply from device tree
LDO_REG8: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.22 err -2
- vcc_3v0: 3000 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc8-supply from device tree
SWITCH_REG1: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.23 err -2
- vcc3v3_s3: at 3300 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808 0-001b: Looking up vcc12-supply from device tree
SWITCH_REG2: supplied by vcc3v3_sys
- vcc3v3_sys: could not add device link regulator.24 err -2
- vcc3v3_s0: at 3300 mV
- pwm-regulator vdd-log: Looking up pwm-supply from device tree
- pwm-regulator vdd-log: Looking up pwm-supply property in node /vdd-log failed
- rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
- rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff8009c70000
- rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff8009c72000
- rk3x-i2c ff120000.i2c: Initialized RK3xxx I2C bus at ffffff8009c74000
- rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at ffffff8009c76000
- fusb302 4-0022: GPIO lookup for consumer int-n
- fusb302 4-0022: using device tree for GPIO lookup
-' - status (0)
- fusb302 4-0022: GPIO lookup for consumer vbus-5v
- fusb302 4-0022: using device tree for GPIO lookup
-' - status (0)
- fusb302 4-0022: GPIO lookup for consumer vbus-other
- fusb302 4-0022: using device tree for GPIO lookup
-'
-'
- fusb302 4-0022: using lookup tables for GPIO lookup
- fusb302 4-0022: lookup for GPIO vbus-other failed
- fusb302 4-0022: GPIO lookup for consumer discharge
- fusb302 4-0022: using device tree for GPIO lookup
-'
-'
- fusb302 4-0022: using lookup tables for GPIO lookup
- fusb302 4-0022: lookup for GPIO discharge failed
- fusb302 4-0022: Can't get property of role, set role to default DRP
- fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
- goodix_ts_probe() start
- Goodix-TS 4-005d: no max-x defined
- Goodix-TS: probe of 4-005d failed with error -22
- rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff8009c78000
- rk-ov4689 1-0036: probing...
- rk-ov4689 1-0036: probing successful
- rk-ov4689 2-0036: probing...
- rk-ov4689 2-0036: probing successful
- rk-ov13850 1-0010: probing...
- rk-ov13850 1-0010: probing successful
- rk-ov13850 2-0010: probing...
- rk-ov13850 2-0010: probing successful
- usbcore: registered new interface driver uvcvideo
- USB Video Class driver (1.1.1)
- rockchip-iodomain ff320000.syscon:io-domains: Looking up pmu1830-supply from device tree
- rockchip-iodomain ff770000.syscon:io-domains: Looking up bt656-supply from device tree
- rockchip-iodomain ff770000.syscon:io-domains: Looking up audio-supply from device tree
- rockchip-iodomain ff770000.syscon:io-domains: Looking up sdmmc-supply from device tree
- rockchip-iodomain ff770000.syscon:io-domains: Looking up gpio1830-supply from device tree
- rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
- rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
- device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
- cpu cpu0: leakage=27
- cpu cpu0: Looking up cpu-supply from device tree
- cpu cpu4: leakage=51
- cpu cpu4: Looking up cpu-supply from device tree
- cpu cpu0: Looking up cpu-supply from device tree
- cpu cpu0: Looking up cpu-supply from device tree
- cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
- cpu cpu4: Looking up cpu-supply from device tree
- cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
+ cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 400000 KHz
+ cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 408000 KHz
+ cpufreq: cpufreq_online: CPU4: Running at unlisted freq: 12000 KHz
+ random: fast init done
+ cpufreq: cpufreq_online: CPU4: Unlisted initial frequency changed to: 408000 KHz
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
Synopsys Designware Multimedia Card Interface Driver
dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
- dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
- dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
- dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply from device tree
- dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply property in node /dwmmc@fe310000 failed
- dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply from device tree
- dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply property in node /dwmmc@fe310000 failed
- dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
- dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
- dwmmc_rockchip fe310000.dwmmc: GPIO lookup for consumer wp
- dwmmc_rockchip fe310000.dwmmc: using device tree for GPIO lookup
-'
-'
- dwmmc_rockchip fe310000.dwmmc: using lookup tables for GPIO lookup
- dwmmc_rockchip fe310000.dwmmc: lookup for GPIO wp failed
+ dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
+ dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
+ mmc_host mmc0: card is non-removable.
+ mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
- dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
- dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
- dwmmc_rockchip fe320000.dwmmc: Looking up vmmc-supply from device tree
- dwmmc_rockchip fe320000.dwmmc: Looking up vqmmc-supply from device tree
- dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer cd
- dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup
-'
-'
- dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup
- dwmmc_rockchip fe320000.dwmmc: lookup for GPIO cd failed
- dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer wp
- dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup
-'
-'
- dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup
- dwmmc_rockchip fe320000.dwmmc: lookup for GPIO wp failed
- rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
- rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
- mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
- dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
+ dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 29,32 bit host data width,256 deep fifo
+ dwmmc_rockchip fe320000.dwmmc: Got CD GPIO
+ mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
sdhci-pltfm: SDHCI platform and OF driver helper
- sdhci-arasan fe330000.sdhci: GPIO lookup for consumer wp
- sdhci-arasan fe330000.sdhci: using device tree for GPIO lookup
-'
-'
- sdhci-arasan fe330000.sdhci: using lookup tables for GPIO lookup
- sdhci-arasan fe330000.sdhci: lookup for GPIO wp failed
- sdhci-arasan fe330000.sdhci: Looking up vmmc-supply from device tree
- sdhci-arasan fe330000.sdhci: Looking up vmmc-supply property in node /sdhci@fe330000 failed
- sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply from device tree
- sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply property in node /sdhci@fe330000 failed
- sdhci-arasan fe330000.sdhci: No vmmc regulator found
- sdhci-arasan fe330000.sdhci: No vqmmc regulator found
+ mmc2: CQHCI version 5.10
+ mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
+ mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
+ mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
+ mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
using ADMA
-' - status (0)
- hidraw: raw HID events driver (C) Jiri Kosina
+ ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
- ashmem: initialized
- rockchip-dmc dmc: unable to get devfreq-event device : dfi
- rockchip-saradc ff100000.saradc: Looking up vref-supply from device tree
- usbcore: registered new interface driver snd-usb-audio
- u32 classifier
Initializing XFRM netlink socket
- NET: Registered protocol family 10
- lib80211: common routines for IEEE802.11 drivers
- lib80211_crypt: registered algorithm 'NULL'
- lib80211_crypt: registered algorithm 'WEP'
- lib80211_crypt: registered algorithm 'CCMP'
- lib80211_crypt: registered algorithm 'TKIP'
-: Enter rfkill_wlan_init
-: Enter rfkill_wlan_probe
-: wlan_platdata_parse_dt: wifi_chip_type = ap6354
-: wlan_platdata_parse_dt: enable wifi power control.
-: wlan_platdata_parse_dt: wifi power controled by gpio.
-'
-'
-'
-' - status (0)
-: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 3, flags = 0.
-: wlan_platdata_parse_dt: The ref_wifi_clk not found !
-: rfkill_wlan_probe: init gpio
-: Exit rfkill_wlan_probe
-: Enter rfkill_rk_init
-' - status (0)
-: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 83.
-'
-' - status (0)
-: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 9.
-' - status (0)
-: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 90.
-' - status (0)
-: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 4.
-: Request irq for bt wakeup host
-: ** disable irq
-: bt_default device registered.
+ NET: Registered protocol family 17
+ 9pnet: Installing 9P2000 support
Key type dns_resolver registered
- cif_isp10_v4l2_drv_probe: CIF ISP10 driver version: v0.2.1
- cif_isp10_pltfrm_dev_init(886) ERR: could not get default pinstate
- cif_isp10_pltfrm_dev_init WARN: could not get pins_sleep pinstate
- cif_isp10_pltfrm_dev_init WARN: could not get pins_inactive pinstate
-' - status (0)
-'
-'
-'
-'
-'
-' - status (0)
- rockchip-iodomain ff770000.syscon:io-domains: Setting to 3000000 done
- vccio_sd: ramp_delay not set
- rockchip-iodomain ff770000.syscon:io-domains: Setting to 1800000 done
- rk-ov13850.ov_camera_module_write_config(180) ERR: no active sensor configuration
- rk-ov13850.ov_camera_module_write_config(231) ERR: failed with error -14
- rk-ov13850.pltfrm_camera_module_read_reg(1035) ERR: i2c read from offset 0x0000300a failed with error -6
- rk-ov13850.pltfrm_camera_module_read_reg(1035) ERR: i2c read from offset 0x0000300b failed with error -6
- rk-ov13850.ov13850_check_camera_id(1858) ERR: register read failed, camera module powered off?
- rk-ov13850.ov13850_check_camera_id(1876) ERR: failed with error (-6)
- rk-ov13850.ov_camera_module_attach(254) ERR: failed with error -6
- cif_isp10_img_src_v4l2_i2c_subdev_to_img_src(59) ERR: failed with error -6
- cif_isp10_img_src_to_img_src(70) ERR: to_img_src failed!
- cif_isp10_img_src_to_img_src(78) ERR: failed with error -14
-' - status (0)
-'
-'
-'
-'
-'
-' - status (0)
- mmc_host mmc0: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
- mmc1: MAN_BKOPS_EN bit is not set
- mmc1: new HS200 MMC card at address 0001
- mmcblk1: mmc1:0001 AJTD4R 14.6 GiB
- mmcblk1boot0: mmc1:0001 AJTD4R partition 1 4.00 MiB
- mmcblk1boot1: mmc1:0001 AJTD4R partition 2 4.00 MiB
- mmcblk1rpmb: mmc1:0001 AJTD4R partition 3 4.00 MiB
- mmcblk1: p1
- fusb302 4-0022: CC connected in CC1 as UFP
- rk-ov4689.ov_camera_module_write_config(180) ERR: no active sensor configuration
- rk-ov4689.ov_camera_module_write_config(231) ERR: failed with error -14
- rk-ov4689.pltfrm_camera_module_read_reg(1035) ERR: i2c read from offset 0x0000300a failed with error -6
- rk-ov4689.pltfrm_camera_module_read_reg(1035) ERR: i2c read from offset 0x0000300b failed with error -6
- rk-ov4689.ov4689_check_camera_id(860) ERR: register read failed, camera module powered off?
- rk-ov4689.ov4689_check_camera_id(878) ERR: failed with error (-6)
- rk-ov4689.ov_camera_module_attach(254) ERR: failed with error -6
- cif_isp10_img_src_v4l2_i2c_subdev_to_img_src(59) ERR: failed with error -6
- cif_isp10_img_src_to_img_src(70) ERR: to_img_src failed!
- cif_isp10_img_src_to_img_src(78) ERR: failed with error -14
- cif_isp10_img_srcs_init(1101) ERR: failed with error -14
- cif_isp10_create(6037) ERR: cif_isp10_img_srcs_init failed
- cif_isp10_create(6074) ERR: failed with error -14
- cif_isp10_v4l2_drv_probe: CIF ISP10 driver version: v0.2.1
- cif_isp10_pltfrm_dev_init(886) ERR: could not get default pinstate
- cif_isp10_pltfrm_dev_init WARN: could not get pins_sleep pinstate
- cif_isp10_pltfrm_dev_init WARN: could not get pins_inactive pinstate
-' - status (0)
-'
-'
-'
-'
-'
-' - status (0)
- rk-ov13850.ov_camera_module_write_config(180) ERR: no active sensor configuration
- rk-ov13850.ov_camera_module_write_config(231) ERR: failed with error -14
- rk-ov13850.pltfrm_camera_module_read_reg(1035) ERR: i2c read from offset 0x0000300a failed with error -6
- rk-ov13850.pltfrm_camera_module_read_reg(1035) ERR: i2c read from offset 0x0000300b failed with error -6
- rk-ov13850.ov13850_check_camera_id(1858) ERR: register read failed, camera module powered off?
- rk-ov13850.ov13850_check_camera_id(1876) ERR: failed with error (-6)
- rk-ov13850.ov_camera_module_attach(254) ERR: failed with error -6
- cif_isp10_img_src_v4l2_i2c_subdev_to_img_src(59) ERR: failed with error -6
- cif_isp10_img_src_to_img_src(70) ERR: to_img_src failed!
- cif_isp10_img_src_to_img_src(78) ERR: failed with error -14
-' - status (0)
-'
-'
-'
-'
-'
-' - status (0)
- rk-ov4689.ov_camera_module_write_config(180) ERR: no active sensor configuration
- rk-ov4689.ov_camera_module_write_config(231) ERR: failed with error -14
- rk-ov4689.pltfrm_camera_module_read_reg(1035) ERR: i2c read from offset 0x0000300a failed with error -6
- rk-ov4689.pltfrm_camera_module_read_reg(1035) ERR: i2c read from offset 0x0000300b failed with error -6
- rk-ov4689.ov4689_check_camera_id(860) ERR: register read failed, camera module powered off?
- rk-ov4689.ov4689_check_camera_id(878) ERR: failed with error (-6)
- rk-ov4689.ov_camera_module_attach(254) ERR: failed with error -6
- cif_isp10_img_src_v4l2_i2c_subdev_to_img_src(59) ERR: failed with error -6
- cif_isp10_img_src_to_img_src(70) ERR: to_img_src failed!
- cif_isp10_img_src_to_img_src(78) ERR: failed with error -14
- cif_isp10_img_srcs_init(1101) ERR: failed with error -14
- cif_isp10_create(6037) ERR: cif_isp10_img_srcs_init failed
- cif_isp10_create(6074) ERR: failed with error -14
- Registered cp15_barrier emulation handler
- Registered setend emulation handler
registered taskstats version 1
Loading compiled-in X.509 certificates
- Btrfs loaded, integrity-checker=on
- BTRFS: selftest: Running btrfs free space cache tests
- BTRFS: selftest: Running extent only tests
- BTRFS: selftest: Running bitmap only tests
- BTRFS: selftest: Running bitmap and extent tests
- BTRFS: selftest: Running space stealing from bitmap to extent
- BTRFS: selftest: Free space cache tests finished
- BTRFS: selftest: Running extent buffer operation tests
- BTRFS: selftest: Running btrfs_split_item tests
- BTRFS: selftest: Running find delalloc tests
- BTRFS: selftest: Running btrfs_get_extent tests
- BTRFS: selftest: Running hole first btrfs_get_extent test
- BTRFS: selftest: Running outstanding_extents tests
- BTRFS: selftest: Running qgroup tests
- BTRFS: selftest: Qgroup basic add
- BTRFS: selftest: Qgroup multiple refs test
- Key type encrypted registered
- phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up phy-supply from device tree
- vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e450.6 err -2
- phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up phy-supply from device tree
- phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed
- phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up vbus-supply from device tree
- phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed
- phy phy-ff770000.syscon:usb2-phy@e450.7: Failed to get VBUS supply regulator
- phy phy-ff7c0000.phy.8: Looking up phy-supply from device tree
- phy phy-ff7c0000.phy.8: Looking up phy-supply property in node /phy@ff7c0000/dp-port failed
- phy phy-ff7c0000.phy.9: Looking up phy-supply from device tree
- phy phy-ff7c0000.phy.9: Looking up phy-supply property in node /phy@ff7c0000/usb3-port failed
- Rockchip DRM driver version: v1.0.1
- rockchip-drm display-subsystem: defer getting devfreq
- rockchip-vop ff900000.vop: missing rockchip,grf property
- rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008da3e08)
- rockchip-vop ff8f0000.vop: missing rockchip,grf property
- rockchip-drm display-subsystem: bound ff8f0000.vop (ops 0xffffff8008da3e08)
- dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
- rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff8008d9a680)
- Supports vblank timestamp caching Rev 2 (21.10.2013).
- No driver support for vblank timestamp query.
- rockchip-drm display-subsystem: failed to parse loader memory
- dwmmc_rockchip fe320000.dwmmc: Successfully tuned phase to 201
- mmc0: new ultra high speed SDR104 SDHC card at address 1234
- mmcblk0: mmc0:1234 SA16G 14.4 GiB
- mmcblk0: p1
- Update mode to 1920x1080p60, type: 11
- vendor storage:20160801 ret = 0
- Console: switching to colour frame buffer device 240x67
- rockchip-drm display-subsystem: fb0: frame buffer device
- xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
- xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 3
- xhci-hcd xhci-hcd.7.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
- xhci-hcd xhci-hcd.7.auto: irq 231, io mem 0xfe800000
- usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
- usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb3: Product: xHCI Host Controller
- usb usb3: Manufacturer: Linux 4.4.178-rk3399 xhci-hcd
- usb usb3: SerialNumber: xhci-hcd.7.auto
- hub 3-0:1.0: USB hub found
- hub 3-0:1.0: 1 port detected
- xhci-hcd xhci-hcd.7.auto: xHCI Host Controller
- xhci-hcd xhci-hcd.7.auto: new USB bus registered, assigned bus number 4
- usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
- usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
- usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb4: Product: xHCI Host Controller
- usb usb4: Manufacturer: Linux 4.4.178-rk3399 xhci-hcd
- usb usb4: SerialNumber: xhci-hcd.7.auto
- hub 4-0:1.0: USB hub found
- hub 4-0:1.0: 1 port detected
- xhci-hcd xhci-hcd.7.auto: remove, state 1
- usb usb4: USB disconnect, device number 1
- xhci-hcd xhci-hcd.7.auto: Host not halted after 16000 microseconds.
- xhci-hcd xhci-hcd.7.auto: Host controller not halted, aborting reset.
- xhci-hcd xhci-hcd.7.auto: USB bus 4 deregistered
- xhci-hcd xhci-hcd.7.auto: remove, state 1
- usb usb3: USB disconnect, device number 1
- xhci-hcd xhci-hcd.7.auto: USB bus 3 deregistered
- phy phy-ff770000.syscon:usb2-phy@e450.7: charger = USB_CDP_CHARGER
- rockchip-dwc3 usb0: USB peripheral connected
- xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
- xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
- xhci-hcd xhci-hcd.8.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010
- xhci-hcd xhci-hcd.8.auto: irq 232, io mem 0xfe900000
- usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
- usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb3: Product: xHCI Host Controller
- usb usb3: Manufacturer: Linux 4.4.178-rk3399 xhci-hcd
- usb usb3: SerialNumber: xhci-hcd.8.auto
- hub 3-0:1.0: USB hub found
- hub 3-0:1.0: 1 port detected
- xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
- xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
- usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
- usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
- usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb4: Product: xHCI Host Controller
- usb usb4: Manufacturer: Linux 4.4.178-rk3399 xhci-hcd
- usb usb4: SerialNumber: xhci-hcd.8.auto
- hub 4-0:1.0: USB hub found
- hub 4-0:1.0: 1 port detected
- ehci-platform fe380000.usb: EHCI Host Controller
- ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5
- ehci-platform fe380000.usb: irq 28, io mem 0xfe380000
- ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
- usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
+ zswap: default zpool zbud not available
+ zswap: pool creation failed
+ dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
+ dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
+ dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
+ dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
+ input: gpio-keys as /devices/platform/gpio-keys/input/input0
+ hctosys: unable to open rtc device (rtc0)
+ of_cfs_init
+ of_cfs_init: OK
+ vcc1v8_s3: supplied by vcc_1v8
+ dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
+ dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
+ ALSA device list:
+ No soundcards found.
+ Freeing unused kernel memory: 960K
+ Run /init as init process
+ mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
+ dwmmc_rockchip fe320000.dwmmc: All phases bad!
+ mmc1: tuning execution failed: -5
+ mmc1: error -5 whilst initialising SD card
+ mmc_host mmc0: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
+ mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
+ mmc_host mmc1: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
+ dwmmc_rockchip fe320000.dwmmc: All phases bad!
+ mmc1: tuning execution failed: -5
+ mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
+ rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
+ rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
+ rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
+ rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
+ rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
+ rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
+ rk_gmac-dwmac fe300000.ethernet: clock input from PHY
+ rk_gmac-dwmac fe300000.ethernet: init for RGMII
+ rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
+ rk_gmac-dwmac fe300000.ethernet: DWMAC1000
+ rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
+ rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
+ rk_gmac-dwmac fe300000.ethernet: COE Type 2
+ rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
+ rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
+ rk_gmac-dwmac fe300000.ethernet: Normal descriptors
+ rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
+ rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
+ rk_gmac-dwmac fe300000.ethernet (unnamed net_device) (uninitialized): device MAC address 42:7f:64:df:51:12
+ rk808-rtc rk808-rtc: registered as rtc0
+ dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
+ dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
+ mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
+ mmc1: new high speed SDHC card at address 1234
+ mmcblk1: mmc1:1234 SA16G 14.4 GiB
+ mmcblk1: p1
+ xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
+ xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5
+ xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
+ xhci-hcd xhci-hcd.0.auto: irq 224, io mem 0xfe900000
+ usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb5: Product: EHCI Host Controller
- usb usb5: Manufacturer: Linux 4.4.178-rk3399 ehci_hcd
- usb usb5: SerialNumber: fe380000.usb
+ usb usb5: Product: xHCI Host Controller
+ usb usb5: Manufacturer: Linux 5.1.0-rk3399 xhci-hcd
+ usb usb5: SerialNumber: xhci-hcd.0.auto
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
- ohci-platform fe3a0000.usb: Generic Platform OHCI controller
- ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6
- ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000
- usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
+ xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
+ xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 6
+ xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
+ usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
+ usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.01
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
- usb usb6: Product: Generic Platform OHCI controller
- usb usb6: Manufacturer: Linux 4.4.178-rk3399 ohci_hcd
- usb usb6: SerialNumber: fe3a0000.usb
+ usb usb6: Product: xHCI Host Controller
+ usb usb6: Manufacturer: Linux 5.1.0-rk3399 xhci-hcd
+ usb usb6: SerialNumber: xhci-hcd.0.auto
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
- input: adc-keys as /devices/platform/adc-keys/input/input0
- dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
- dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
- dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
- dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
- dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
- dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply from device tree
- dwmmc_rockchip fe310000.dwmmc: Looking up vmmc-supply property in node /dwmmc@fe310000 failed
- dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply from device tree
- dwmmc_rockchip fe310000.dwmmc: Looking up vqmmc-supply property in node /dwmmc@fe310000 failed
- dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
- dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
- dwmmc_rockchip fe310000.dwmmc: GPIO lookup for consumer wp
- dwmmc_rockchip fe310000.dwmmc: using device tree for GPIO lookup
-'
-'
- dwmmc_rockchip fe310000.dwmmc: using lookup tables for GPIO lookup
- dwmmc_rockchip fe310000.dwmmc: lookup for GPIO wp failed
- platform sdio-pwrseq: GPIO lookup for consumer reset
- platform sdio-pwrseq: using device tree for GPIO lookup
-' - status (0)
- dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
- mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
- dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
- rockchip-dmc dmc: Looking up center-supply from device tree
- rockchip-dmc dmc: Failed to get leakage
- rockchip-dmc dmc: Looking up center-supply from device tree
- vdd_center: could not add device link dmc err -17
- vdd_center: Failed to create debugfs directory
- rockchip-dmc dmc: Failed to get pvtm
- rockchip-dmc dmc: could not find power_model node
-'
-'
- asoc-simple-card rt5651-sound: rt5651-aif1 <-> ff890000.i2s mapping ok
- asoc-simple-card rt5651-sound: ASoC: no source widget found for MICBIAS1
- asoc-simple-card rt5651-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack
- rt5651 1-001a: ASoC: mux INL1 Mux has no paths
- rt5651 1-001a: ASoC: mux INR1 Mux has no paths
- rt5651 1-001a: ASoC: mux INL2 Mux has no paths
- rt5651 1-001a: ASoC: mux INR2 Mux has no paths
-'
-'
- asoc-simple-card hdmi-sound: i2s-hifi <-> ff8a0000.i2s mapping ok
-'
-'
- rockchip-spdif ff870000.spdif: Missing dma channel for stream: 0
- rockchip-spdif ff870000.spdif: ASoC: pcm constructor failed: -22
- asoc-simple-card spdif-sound: ASoC: can't create pcm ff870000.spdif-dit-hifi :-22
- asoc-simple-card spdif-sound: ASoC: failed to instantiate card -22
- asoc-simple-card: probe of spdif-sound failed with error -22
-
- =======================================================
- ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
- =======================================================
- Realtek 8188EU USB WiFi driver (Powered by Rockchip,Ver v5.2.2.3_24783.20171030) init.
-: rockchip_wifi_power: 1
-: wifi turn on power. -1
- RTW: module init start
- RTW: rtl8188eu v5.2.2.3_24783.20171030
-: rockchip_wifi_get_oob_irq: Enter
- usbcore: registered new interface driver rtl8188eu
- RTW: module init ret=0
-' - status (0)
- gpio-5 (GPIO Key Power): gpiod_set_debounce: missing set() or set_debounce() operations
- input: gpio-keys as /devices/platform/gpio-keys/input/input1
- dhd_module_init: in Dongle Host Driver, version 1.579.77.41.9 (r)
- ======== dhd_wlan_init_plat_data ========
-: rockchip_wifi_get_oob_irq: Enter
- dhd_wlan_init_gpio: WL_REG_ON=-1, WL_HOST_WAKE=-1
- dhd_wlan_init_gpio: oob_irq=72, oob_irq_flags=0x414
- dhd_wifi_platform_load: Enter
- Power-up adapter 'DHD generic adapter'
- wifi_platform_set_power = 1
- ======== PULL WL_REG_ON(-1) HIGH! ========
-: rockchip_wifi_power: 1
-: wifi turn on power. -1
- mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
- mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
- mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
- mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
- mmc_host mmc2: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
- rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:50:11 UTC (1358499011)
- vcc_lcd: disabling
- ALSA device list:
- #0: realtek,rt5651-codec
- #1: rockchip,hdmi
- ttyS2 - failed to request DMA, use interrupt mode
- Freeing unused kernel memory: 1216K
- usb 3-1: new high-speed USB device number 2 using xhci-hcd
- usb 3-1: New USB device found, idVendor=2109, idProduct=2817
- usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- usb 3-1: Product: USB2.0 Hub
- usb 3-1: Manufacturer: VIA Labs, Inc.
- wifi_platform_bus_enumerate device present 1
- ======== Card detection to detect SDIO card! ========
- mmc2:mmc host rescan start!
- hub 3-1:1.0: USB hub found
- hub 3-1:1.0: 4 ports detected
- dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 179
- mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
- mmc2: new ultra high speed SDR104 SDIO card at address 0001
- bcmsdh_register: register client driver
- bcmsdh_sdmmc_probe: Enter num=1
- bcmsdh_sdmmc_probe: Enter num=2
- bus num (host idx)=2, slot num (rca)=1
- found adapter info 'DHD generic adapter'
- sdioh_attach: set sd_f2_blocksize 256
- sdioh_attach: sd clock rate = 0
- dhdsdio_probe : no mutex held. set lock
- F1 signature read @0x18000000=0x17224356
- F1 signature OK, socitype:0x1 chip:0x4354 rev:0x2 pkg:0x2
- DHD: dongle ram size is set to 786432(orig 786432) at 0x180000
- dhd_conf_set_chiprev: chip=0x4354, chiprev=2
- CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211
- CFG80211-ERROR) wl_init_prof : wl_init_prof: No profile
- wl_escan_attach: Enter
- wl_escan_init: Enter
- usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
- wl_create_event_handler(): thread:wl_escan_handler:de started
- dhd_init_logstrs_array: Failed to open the file /installmedia/logstrs.bin
- tsk Enter, tsk = 0xffffffc0dc9101b0
- dhd_attach(): thread:dhd_watchdog_thread:df started
- dhd_attach(): thread:dhd_dpc:e0 started
- dhd_attach(): thread:dhd_rxf:e1 started
- dhd_deferred_work_init: work queue initialized
- dhd_bus_set_default_min_res_mask: Unhandled chip id
-=0x10ac
- Dongle Host Driver, version 1.579.77.41.9 (r)
- wl_ext_iapsta_attach_netdev: bssidx=0
- MAC: cc:4b:73:03:b3:10
-
- dhd_wl_ioctl: returning as busstate=0
- dhd_dbg_detach_pkt_monitor, 2204
- dhd_bus_devreset: == Power OFF ==
- bcmsdh_oob_intr_unregister: Enter
- bcmsdh_oob_intr_unregister: irq is not registered
- dhd_txglom_enable: enable 0
- dhd_conf_set_txglom_params: txglom_mode=copy
- dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0
- dhd_conf_set_txglom_params: tx_in_rx=1, txinrx_thres=128, dhd_txminmax=-1
- dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
- dhd_bus_devreset: WLAN OFF DONE
- wifi_platform_set_power = 0
- ======== PULL WL_REG_ON(-1) LOW! ========
-: rockchip_wifi_power: 0
-: wifi shut off power.
- dhdsdio_probe : the lock is released.
- dhd_module_init: Exit err=0
- usb 4-1: New USB device found, idVendor=2109, idProduct=0817
- usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- usb 4-1: Product: USB3.0 Hub
- usb 4-1: Manufacturer: VIA Labs, Inc.
- hub 4-1:1.0: USB hub found
- hub 4-1:1.0: 4 ports detected
- mali ff9a0000.gpu: Looking up mali-supply from device tree
- mali ff9a0000.gpu: leakage=35
- mali ff9a0000.gpu: Looking up mali-supply from device tree
- vdd_gpu: could not add device link ff9a0000.gpu err -17
- vdd_gpu: Failed to create debugfs directory
- mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0
- mali ff9a0000.gpu: Protected mode not available
- mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
- ERROR: Bad of_node_put() on /gpu@ff9a0000
- CPU: 4 PID: 229 Comm: systemd-udevd Not tainted 4.4.178-rk3399 #2
- Hardware name: FriendlyElec NanoPi M4 (DT)
- Call trace:
- dump_backtrace+0x0/0x220
- show_stack+0x24/0x30
- dump_stack+0x98/0xc0
- of_node_release+0x3c/0xb0
- kobject_put+0x178/0x1b8
- of_node_put+0x24/0x30
- of_find_compatible_node+0x50/0xa4
-
-
-
-
-
-
-
- platform_drv_probe+0x5c/0xb0
- driver_probe_device+0x260/0x3d0
- __driver_attach+0x54/0xa0
- bus_for_each_dev+0x8c/0x9c
- driver_attach+0x30/0x3c
- bus_add_driver+0x1fc/0x240
- driver_register+0xa0/0xd8
- __platform_driver_register+0x58/0x64
-
- do_one_initcall+0x18c/0x194
- do_init_module+0x64/0x1b8
- load_module+0x18f4/0x1e68
- SyS_finit_module+0xb0/0xbc
- el0_svc_naked+0x24/0x28
- mali ff9a0000.gpu: Using configured power model mali-simple-power-model, and fallback mali-simple-power-model
- : kbase_devfreq_init(); success initing power_model_simple.
- mali ff9a0000.gpu: Probed as mali0
- usb 3-1.1: new low-speed USB device number 3 using xhci-hcd
- usb 3-1.1: New USB device found, idVendor=0e8f, idProduct=00a8
- usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
- usb 3-1.1: Product: 2.4G RX
- usb 3-1.1: Manufacturer: DaKai
- usb 3-1.1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
- usb 3-1.1: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
- input: DaKai 2.4G RX as /devices/platform/usb1/fe900000.dwc3/xhci-hcd.8.auto/usb3/3-1/3-1.1/3-1.1:1.0/0003:0E8F:00A8.0001/input/input2
- on usb-xhci-hcd.8.auto-1.1/input0
- input: DaKai 2.4G RX as /devices/platform/usb1/fe900000.dwc3/xhci-hcd.8.auto/usb3/3-1/3-1.1/3-1.1:1.1/0003:0E8F:00A8.0002/input/input3
- random: nonblocking pool is initialized
- on usb-xhci-hcd.8.auto-1.1/input1
- fusb302 4-0022: PD disabled
- EXT4-fs (mmcblk1p1): mounted filesystem with ordered data mode. Opts: (null)
+ dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
+ OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/otg-port
+ xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
+ xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 7
+ xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
+ xhci-hcd xhci-hcd.1.auto: irq 223, io mem 0xfe800000
+ usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01
+ usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
+ usb usb7: Product: xHCI Host Controller
+ usb usb7: Manufacturer: Linux 5.1.0-rk3399 xhci-hcd
+ usb usb7: SerialNumber: xhci-hcd.1.auto
+ hub 7-0:1.0: USB hub found
+ hub 7-0:1.0: 1 port detected
+ xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
+ xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 8
+ xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
+ usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
+ usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.01
+ usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
+ usb usb8: Product: xHCI Host Controller
+ usb usb8: Manufacturer: Linux 5.1.0-rk3399 xhci-hcd
+ usb usb8: SerialNumber: xhci-hcd.1.auto
+ hub 8-0:1.0: USB hub found
+ hub 8-0:1.0: 1 port detected
+ libphy: stmmac: probed
+ (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
+ (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
+ dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 192
+ mmc0: new ultra high speed SDR104 SDIO card at address 0001
+ raid6: neonx8 gen() 3522 MB/s
+ raid6: neonx8 xor() 2675 MB/s
+ raid6: neonx4 gen() 3149 MB/s
+ raid6: neonx4 xor() 2384 MB/s
+ raid6: neonx2 gen() 2457 MB/s
+ raid6: neonx2 xor() 1774 MB/s
+ raid6: neonx1 gen() 1851 MB/s
+ raid6: neonx1 xor() 1507 MB/s
+ raid6: int64x8 gen() 1787 MB/s
+ raid6: int64x8 xor() 1208 MB/s
+ raid6: int64x4 gen() 1773 MB/s
+ raid6: int64x4 xor() 1091 MB/s
+ raid6: int64x2 gen() 1301 MB/s
+ raid6: int64x2 xor() 783 MB/s
+ raid6: int64x1 gen() 931 MB/s
+ raid6: int64x1 xor() 569 MB/s
+ raid6: using algorithm neonx8 gen() 3522 MB/s
+ raid6: .... xor() 2675 MB/s, rmw enabled
+ raid6: using neon recovery algorithm
+ xor: measuring software checksum speed
+ 8regs : 8736.000 MB/sec
+ 32regs : 9769.000 MB/sec
+ arm64_neon: 8775.000 MB/sec
+ xor: using function: 32regs (9769.000 MB/sec)
+ Btrfs loaded, crc32c=crc32c-generic
+ usb 6-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
+ usb 6-1: New USB device found, idVendor=2109, idProduct=0817, bcdDevice= 0.50
+ usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
+ usb 6-1: Product: USB3.0 Hub
+ usb 6-1: Manufacturer: VIA Labs, Inc.
+ hub 6-1:1.0: USB hub found
+ hub 6-1:1.0: 4 ports detected
+ usb 5-1: new high-speed USB device number 2 using xhci-hcd
+ usb 5-1: New USB device found, idVendor=2109, idProduct=2817, bcdDevice= 0.50
+ usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
+ usb 5-1: Product: USB2.0 Hub
+ usb 5-1: Manufacturer: VIA Labs, Inc.
+ hub 5-1:1.0: USB hub found
+ hub 5-1:1.0: 4 ports detected
+ random: crng init done
+ usb 5-1.1: new low-speed USB device number 3 using xhci-hcd
+ usb 5-1.1: New USB device found, idVendor=0e8f, idProduct=00a8, bcdDevice= 3.11
+ usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
+ usb 5-1.1: Product: 2.4G RX
+ usb 5-1.1: Manufacturer: DaKai
+ input: DaKai 2.4G RX as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.0.auto/usb5/5-1/5-1.1/5-1.1:1.0/0003:0E8F:00A8.0001/input/input1
+ on usb-xhci-hcd.0.auto-1.1/input0
+ input: DaKai 2.4G RX Mouse as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.0.auto/usb5/5-1/5-1.1/5-1.1:1.1/0003:0E8F:00A8.0002/input/input2
+ input: DaKai 2.4G RX System Control as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.0.auto/usb5/5-1/5-1.1/5-1.1:1.1/0003:0E8F:00A8.0002/input/input3
+ EXT4-fs (mmcblk1p1): mounted filesystem with writeback data mode. Opts: (null)
+ input: DaKai 2.4G RX Consumer Control as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.0.auto/usb5/5-1/5-1.1/5-1.1:1.1/0003:0E8F:00A8.0002/input/input4
+ input: DaKai 2.4G RX as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.0.auto/usb5/5-1/5-1.1/5-1.1:1.1/0003:0E8F:00A8.0002/input/input5
+ on usb-xhci-hcd.0.auto-1.1/input1
: System time before build time, advancing clock.
- ip_tables: (C) 2000-2006 Netfilter Core Team
- cgroup: cgroup2: unknown option "nsdelegate"
+ NET: Registered protocol family 10
+ Segment Routing with IPv6
: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
: Detected architecture arm64.
: Set hostname to <nanopim4>.
+ ttyS2 - failed to request DMA
: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
-: Reached target Swap.
-: Started Forward Password Requests to Wall Directory Watch.
+: /lib/systemd/system/nanopi-bluetooth.service:11: Support for option SysVStartPriority= has been removed and it is ignored
: Set up automount Arbitrary Executable File Formats File System Automount Point.
-: Reached target User and Group Name Lookups.
-: Reached target System Time Synchronized.
-: Started ntp-systemd-netif.path.
-: Created slice System Slice.
-: Listening on Syslog Socket.
-: Created slice system-serial\x2dgetty.slice.
-: Listening on RPCbind Server Activation Socket.
-: Listening on /dev/initctl Compatibility Named Pipe.
-: Listening on fsck to fsckd communication Socket.
-: Listening on Journal Audit Socket.
-: Listening on Journal Socket.
-: Mounting NFSD configuration filesystem...
-: Starting Nameserver information manager...
-: Starting Set the console keyboard layout...
-: Starting Remount Root and Kernel File Systems...
-: Mounting Kernel Debug File System...
- RPC: Registered named UNIX socket transport module.
- RPC: Registered udp transport module.
- RPC: Registered tcp transport module.
- RPC: Registered tcp NFSv4.1 backchannel transport module.
-: Started Dispatch Password Requests to Console Directory Watch.
- EXT4-fs (mmcblk1p1): re-mounted. Opts: commit=600,errors=remount-ro
-: Starting Load Kernel Modules...
-: Starting Create list of required static device nodes for the current kernel...
- Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
-: Created slice system-postgresql.slice.
-: Listening on udev Control Socket.
- Loading iSCSI transport class v2.0-870.
-: Mounting RPC Pipe File System...
- iscsi: registered transport (tcp)
+: Reached target Remote File Systems.
+: Reached target Swap.
: Created slice User and Session Slice.
-: Reached target Slices.
-: Listening on Journal Socket (/dev/log).
-: Reached target Local Encrypted Volumes.
-: Listening on udev Kernel Socket.
-: Starting udev Coldplug all Devices...
-: Starting Journal Service...
-: Starting Restore / save the current clock...
-: Mounting POSIX Message Queue File System...
-: Mounting Huge Pages File System...
-: Created slice system-postfix.slice.
-: Mounted NFSD configuration filesystem.
-: Started Remount Root and Kernel File Systems.
-: Mounted Kernel Debug File System.
-: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
-: systemd-modules-load.service: Failed with result 'exit-code'.
-: Failed to start Load Kernel Modules.
-: Started Create list of required static device nodes for the current kernel.
-: Mounted RPC Pipe File System.
-: Started Restore / save the current clock.
-: Mounted POSIX Message Queue File System.
-: Mounted Huge Pages File System.
-: Started Nameserver information manager.
-: Reached target Network (Pre).
-: Starting pNFS block layout mapping daemon...
-: Starting Create Static Device Nodes in /dev...
-: Mounting Kernel Configuration File System...
-: Mounting FUSE Control File System...
-: Starting Apply Kernel Variables...
-: Starting Load/Save Random Seed...
-: Started pNFS block layout mapping daemon.
-: Mounted Kernel Configuration File System.
-: Started Create Static Device Nodes in /dev.
-: Mounted FUSE Control File System.
-: Started Apply Kernel Variables.
-: Started Load/Save Random Seed.
-: Starting udev Kernel Device Manager...
-: Started Set the console keyboard layout.
-: Reached target Local File Systems (Pre).
-: Mounting /tmp...
-: Mounted /tmp.
-: Started udev Kernel Device Manager.
-: Started Journal Service.
+ EXT4-fs (mmcblk1p1): re-mounted. Opts: commit=600,errors=remount-ro
: Received request to flush runtime journal from PID 1
- dhd_ioctl_entry: Interface is down
- dhd_ioctl_entry: Interface is down
- rk-vcodec ff650000.vpu_service: Looking up vcodec-supply from device tree
- rk-vcodec ff650000.vpu_service: Looking up vcodec-supply property in node /vpu_service@ff650000 failed
- rk-vcodec ff650000.vpu_service: no regulator for vcodec
- rk-vcodec ff650000.vpu_service: probe device
- rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled
- rk-vcodec ff650000.vpu_service: could not find power_model node
- rk-vcodec ff650000.vpu_service: init success
- rk-vcodec ff660000.rkvdec: Looking up vcodec-supply from device tree
- rk-vcodec ff660000.rkvdec: Looking up vcodec-supply property in node /rkvdec@ff660000 failed
- rk-vcodec ff660000.rkvdec: no regulator for vcodec
- rk-vcodec ff660000.rkvdec: probe device
- rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled
- rk-vcodec ff660000.rkvdec: could not find power_model node
- rk-vcodec ff660000.rkvdec: init success
-: rfkill_rk_set_power: set bt wake_host pin output high!
-: ENABLE UART_RTS
-: DISABLE UART_RTS
-: bt turn on power
- spl: loading out-of-tree module taints kernel.
- SPL: Loaded module v0.7.5-1ubuntu2
- znvpair: module license 'CDDL' taints kernel.
- Disabling lock debugging due to kernel taint
- cfg80211: World regulatory domain updated:
- cfg80211: DFS Master region: unset
- cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
- cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
- cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
- cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
- cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
- cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
- cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
- cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
- ZFS: Loaded module v0.7.5-1ubuntu16.4, ZFS pool version 5000, ZFS filesystem version 5
zram: Added device: zram0
zram: Added device: zram1
zram: Added device: zram2
- zram1: detected capacity change from 0 to 1997836288
- Adding 1951008k swap on /dev/zram1. Priority:5 extents:1 across:1951008k SS
+ zram1: detected capacity change from 0 to 1073741824
+ rockchip-pcie f8000000.pcie: no vpcie12v regulator found
+ rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
+ rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
+ rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
+ media: Linux media interface: v0.10
+ Adding 1048572k swap on /dev/zram1. Priority:5 extents:1 across:1048572k SSFS
+ videodev: Linux video capture interface: v2.00
+ OF: graph: no port node found in /i2c@ff3d0000/typec-portc@22
+ rockchip-vop ff8f0000.vop: Adding to iommu group 1
+ rockchip-vop ff900000.vop: Adding to iommu group 2
+)
+)
+ dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
+)
+ Supports vblank timestamp caching Rev 2 (21.10.2013).
+ No driver support for vblank timestamp query.
+ rockchip-rga ff680000.rga: HW Version: 0x03.02
+ rockchip-rga ff680000.rga: Registered rockchip-rga as /dev/video0
+ Console: switching to colour frame buffer device 240x67
zram0: detected capacity change from 0 to 52428800
+ cfg80211: Loading compiled-in X.509 certificates for regulatory database
+ cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
+ brcmfmac: F1 signature read @0x18000000=0x17224356
+ brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
+ rockchip-drm display-subsystem: fb0: frame buffer device
+ brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac4356-sdio.friendlyarm,nanopi-m4.txt failed with error -2
+ Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0
EXT4-fs (zram0): mounted filesystem without journal. Opts: discard
- IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
- rk_gmac-dwmac fe300000.ethernet: rk_get_eth_addr: mac address: e2:b6:48:ce:c4:e0
- eth0: device MAC address e2:b6:48:ce:c4:e0
- IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
- dhd_open: Enter ffffffc0eba65000
- dhd_open : no mutex held. set lock
- dhd_init_logstrs_array: Failed to open the file /installmedia/logstrs.bin
-
- Dongle Host Driver, version 1.579.77.41.9 (r)
- wl_ext_iapsta_attach_netdev: bssidx=0
- wl_android_wifi_on in 1
- wl_android_wifi_on in 2: g_wifi_on=0
- wifi_platform_set_power = 1
- ======== PULL WL_REG_ON(-1) HIGH! ========
-: rockchip_wifi_power: 1
-: wifi turn on power. -1
- nr_pdflush_threads exported in /proc is scheduled for removal
- sdio_reset_comm():
- mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
- mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
- mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
- mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
- mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
- mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
- mmc_host mmc2: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
- dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 179
- sdioh_start: set sd_f2_blocksize 256
-
-
- dhd_bus_devreset: == WLAN ON ==
- F1 signature read @0x18000000=0x17224356
- F1 signature OK, socitype:0x1 chip:0x4354 rev:0x2 pkg:0x2
- DHD: dongle ram size is set to 786432(orig 786432) at 0x180000
- dhd_bus_set_default_min_res_mask: Unhandled chip id
- dhd_os_open_image: /lib/firmware/rkwifi/config.txt (204 bytes) open success
- dhd_conf_read_others: ccode = ALL
- dhd_conf_read_others: regrev = 0
- dhd_conf_read_sdio_params: dhd_doflow = 1
- dhd_conf_read_others: srl = 15
- dhd_conf_read_others: lrl = 15
- Final fw_path=/lib/firmware/rkwifi/fw_bcm4356a2_ag.bin
- Final nv_path=/lib/firmware/rkwifi/nvram_ap6356.txt
- Final clm_path=/lib/firmware/rkwifi/clm.blob
- Final conf_path=/lib/firmware/rkwifi/config.txt
- dhd_os_open_image: /lib/firmware/rkwifi/fw_bcm4356a2_ag.bin (555412 bytes) open success
- dhd_os_open_image: /lib/firmware/rkwifi/nvram_ap6356.txt (4006 bytes) open success
- NVRAM version: AP6356_NVRAM_V1.1_20141015
- dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
- dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
- bcmsdh_oob_intr_register: HW_OOB irq=72 flags=0x4
- doesn't exist
- dhd_get_memdump_info: MEMDUMP ENABLED = 2
- Disable tdls_auto_op failed. -1
- dhd_preinit_ioctls: Set tcpack_sup_mode 1
- dhd_apply_default_clm: Ignore clm file /lib/firmware/rkwifi/clm.blob
- Firmware up: op_mode=0x0005, MAC=cc:4b:73:03:b3:10
- dhd_preinit_ioctls Set scancache failed -23
- Driver: 1.579.77.41.9 (r)
- Firmware: wl0: Jun 16 2015 14:25:06 version 7.35.184.r1 (TOB) (r559293) FWID 01-b22ae69c
- CLM: 7.10.16
- dhd_txglom_enable: enable 1
- dhd_conf_set_txglom_params: txglom_mode=copy
- dhd_conf_set_txglom_params: txglomsize=36, deferred_tx_len=0
- dhd_conf_set_txglom_params: tx_in_rx=1, txinrx_thres=128, dhd_txminmax=-1
- dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
- dhd_conf_get_disable_proptx: fw_proptx=1, disable_proptx=-1
- dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
- dhd_pno_init: Support Android Location Service
- dhd_wlfc_enable: ret=0
- CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
- CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
- CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
- rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23
- dhd_rtt_init : FTM is not supported
- dhd_preinit_ioctls: SensorHub diabled 0
- dhd_preinit_ioctls failed to set ShubHub disable
- dhd_ndo_get_version: failed, retcode = -23
- dhd_wl_ioctl_get_intiovar: get int iovar wnm_bsstrans_resp failed, ERR -23
- failed to get wnm_bsstrans_resp
- failed to set WNM capabilities
- CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
- dhd_conf_set_country: set country ALL, revision 0
- CONFIG-ERROR) dhd_conf_set_bufiovar: country setting failed -2
- Country code: US (US/0)
- wl_android_wifi_on: Success
- dhd_open : the lock is released.
- dhd_open: Exit ret=0
- NET: Registered protocol family 17
- P2P interface registered
- wl_cfgp2p_add_p2p_disc_if: wdev: ffffffc0ed6eb800, wdev->net: (null)
- WLC_E_IF: NO_IF set, event Ignored
- P2P interface started
- wl_escan_set_scan: ioctl_ver=2
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- unsupported connector property: hdmi_color_depth_capacity
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 8
- Connecting with d0:17:c2:b2:31:28 ssid "razum2um", len (8) channel=9
-
- dhd_dbg_start_pkt_monitor, 1724
- CFG80211-ERROR) wl_escan_handler : escan is not ready ndev ffffffc0eba65000 drv_status 0x0 e_type 69 e_states 10
- wl_iw_event: Link UP with d0:17:c2:b2:31:28
- wl_bss_connect_done succeeded with d0:17:c2:b2:31:28
- wl_bss_connect_done succeeded with d0:17:c2:b2:31:28 vndr_oui: 00-10-18
- EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
+ rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
+ rockchip-pcie: probe of f8000000.pcie failed with error -110
+ phy phy-ff770000.syscon:usb2-phy@e450.2: charger = USB_CDP_CHARGER
+ brcmfmac: brcmf_sdio_readshared: invalid sdpcm_shared address 0xFE8B0174
+ brcmfmac: brcmf_sdio_readshared: unable to obtain sdpcm_shared info: rv=-22 (addr=0xfe8b0174)
+ EXT4-fs (mmcblk1p1): resizing filesystem from 296960 to 3736676 blocks
+ EXT4-fs (mmcblk1p1): resized to 2097152 blocks
+ EXT4-fs (mmcblk1p1): resized to 3670016 blocks
+ EXT4-fs (mmcblk1p1): resized filesystem to 3736676
+ (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
+ rk_gmac-dwmac fe300000.ethernet eth0: No Safety Features support found
+ rk_gmac-dwmac fe300000.ethernet eth0: PTP not supported by HW
+ usbcore: registered new interface driver rtl88xxau
Raw
lsmod.patch
-af_packet
-auth_rpcgss
-autofs4
-grace
-icp
+88XXau
+analogix_dp
+brcmfmac
+brcmutil
+btrfs
+cfg80211
+drm
+drm_kms_helper
+drm_panel_orientation_quirks
+dw_hdmi
+dwmac_rk
+dw_mipi_dsi
+fusb302
ip_tables
-iscsi_tcp
-libiscsi
-libiscsi_tcp
-lockd
-lz4_compress
-midgard_kbase
+ipv6
+media
Module
-nfs_acl
-nfsd
-overlay
-rk_vcodec
-scsi_transport_iscsi
-spl
-sunrpc
+nvmem_rockchip_efuse
+pcie_rockchip_host
+phy_rockchip_pcie
+phy_rockchip_typec
+raid6_pq
+realtek
+rfkill
+rockchipdrm
+rockchip_io_domain
+rockchip_rga
+rockchip_saradc
+rockchip_thermal
+roles
+rtc_rk808
+sch_fq_codel
+stmmac
+stmmac_platform
+tcpm
+typec
+v4l2_mem2mem
+videobuf2_common
+videobuf2_dma_sg
+videobuf2_memops
+videobuf2_v4l2
+videodev
+xor
+xor_neon
x_tables
-zavl
-zcommon
-zfs
-znvpair
+zlib_deflate
zram
-zunicode
+zstd
+zstd_compress
+zstd_decompress
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment