LBE LEDE bootlog

gistfile1.txt

U-Boot 1.1.4-s1038 (May 18 2017 - 17:50:47)

Board: Ubiquiti Networks AR9342 board (e8f5-101383.1122.0031)
Reset: Normal
DRAM:  64 MB
Flash: 16 MB (0xc2, 0x20, 0x18)
PCIe WLAN Module found (#1).
Net:   AR8035
eth0, eth1
Radio: 0777:e8f5
Hit any key to stop autoboot:  0
## Booting image at 9f050000 ...
   Image Name:   MIPS OpenWrt Linux-4.9.72
   Created:      2017-12-31  23:23:01 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1424332 Bytes =  1.4 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x9f050040 ...OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.9.72 (robimarko@Builder) (gcc version 6.3.0 (OpenWrt GCC 6.3.0 r5679-dbee267) ) #0 Sun Dec 31 23:23:01 2017
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9342 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] OF: fdt:No valid device tree found, continuing without
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=UBNT-LITEBEAM-5AC-23 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,15744k(firmware),256k(cfg)ro,64k(EEPROM)ro console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59768K/65536K available (3220K kernel code, 164K rwdata, 820K rodata, 332K init, 213K bss, 5768K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7144898866 ns
[    0.000011] sched_clock: 32 bits at 267MHz, resolution 3ns, wraps every 8027976190ns
[    0.008341] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.091173] pid_max: default: 32768 minimum: 301
[    0.096210] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.103263] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.113840] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.124355] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.131528] NET: Registered protocol family 16
[    0.138054] MIPS: machine is Ubiquiti LiteBeam 5AC-23
[    0.376792] registering PCI controller with io_map_base unset
[    0.397641] PCI host bridge to bus 0000:00
[    0.402024] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.409397] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.415328] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.422565] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.431501] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    0.439349] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[    0.447048] pci 0000:00:00.0: using irq 40 for pin 1
[    0.453141] clocksource: Switched to clocksource MIPS
[    0.459755] NET: Registered protocol family 2
[    0.465420] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.472851] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.479688] TCP: Hash tables configured (established 1024 bind 1024)
[    0.486569] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.492809] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.499817] NET: Registered protocol family 1
[    0.509224] Crashlog allocated RAM at address 0x3f00000
[    0.515899] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.530657] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.536918] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.556590] io scheduler noop registered
[    0.560767] io scheduler deadline registered (default)
[    0.566778] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.574088] console [ttyS0] disabled
[    0.598003] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.607204] console [ttyS0] enabled
[    0.607204] console [ttyS0] enabled
[    0.614631] bootconsole [early0] disabled
[    0.614631] bootconsole [early0] disabled
[    0.627255] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    0.638685] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    0.643897] 5 cmdlinepart partitions found on MTD device spi0.0
[    0.649906] Creating 5 MTD partitions on "spi0.0":
[    0.654799] 0x000000000000-0x000000040000 : "u-boot"
[    0.661580] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.668893] 0x000000050000-0x000000fb0000 : "firmware"
[    0.695639] 2 uimage-fw partitions found on MTD device firmware
[    0.701672] 0x000000050000-0x0000001b0000 : "kernel"
[    0.708304] 0x0000001b0000-0x000000fb0000 : "rootfs"
[    0.715278] mtd: device 4 (rootfs) set to be root filesystem
[    0.721062] 1 squashfs-split partitions found on MTD device rootfs
[    0.727405] 0x000000490000-0x000000fb0000 : "rootfs_data"
[    0.734816] 0x000000fb0000-0x000000ff0000 : "cfg"
[    0.741453] 0x000000ff0000-0x000001000000 : "EEPROM"
[    0.749569] libphy: Fixed MDIO Bus: probed
[    0.767846] libphy: ag71xx_mdio: probed
[    1.493421] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd072, driver=Atheros 8035 ethernet]
[    1.504471] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    1.512146] NET: Registered protocol family 10
[    1.519969] NET: Registered protocol family 17
[    1.524731] 8021q: 802.1Q VLAN Support v1.8
[    1.535697] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.545099] Freeing unused kernel memory: 332K
[    1.549615] This architecture does not have kernel memory protection.
[    2.189466] init: Console is alive
[    2.193262] init: - watchdog -
[    2.510417] random: fast init done
[    3.279315] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.342375] usbcore: registered new interface driver usbfs
[    3.348107] usbcore: registered new interface driver hub
[    3.353666] usbcore: registered new device driver usb
[    3.365237] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.373896] ehci-platform: EHCI generic platform driver
[    3.380022] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.397927] init: - preinit -
[    4.704057] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.022527] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[    8.059380] urandom-seed: Seed file not found (/etc/urandom.seed)
[    8.210042] procd: - early -
[    8.213088] procd: - watchdog -
[    8.840455] procd: - watchdog -
[    8.844031] procd: - ubus -
[    8.928346] procd: - init -
Please press Enter to activate this console.
[    9.381820] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.422009] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.441394] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[    9.449589] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[    9.460329] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.476344] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[    9.549042] xt_time: kernel timezone is -0000
[    9.791208] PPP generic driver version 2.4.2
[    9.798497] NET: Registered protocol family 24
[    9.878131] kmodloader: done loading kernel modules from /etc/modules.d/*
[   19.091248] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   19.143214] jffs2_build_filesystem(): unlocking the mtd device... [   19.149322] done.
[   19.151279] jffs2_build_filesystem(): erasing all blocks after the end marker... [   24.836546] br-lan: port 1(eth0) entered blocking state
[   24.841869] br-lan: port 1(eth0) entered disabled state
[   24.847678] device eth0 entered promiscuous mode
[   24.913935] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   33.144631] eth0: link up (100Mbps/Full duplex)
[   33.149294] br-lan: port 1(eth0) entered blocking state
[   33.154644] br-lan: port 1(eth0) entered forwarding state
[   33.204487] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   73.103227] done.
[   73.105230] jffs2: notice: (822) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.