Skip to content

Instantly share code, notes, and snippets.

@robimarko

robimarko/gist:113216f566ccf159dfd33933889da042

Created August 2, 2022 16:06
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save robimarko/113216f566ccf159dfd33933889da042 to your computer and use it in GitHub Desktop.
Save robimarko/113216f566ccf159dfd33933889da042 to your computer and use it in GitHub Desktop.
Download ZIP
Raw
gistfile1.txt
TIM-1.0
mv_ddr-devel-gd5acc10 DDR4 16b 1GB 1CS
WTMI-devel-18.12.1-1d97715
WTMI: system early-init
SVC REV: 5, CPU VDD voltage: 1.213V
Setting clocks: CPU 1200 MHz, DDR 750 MHz
CZ.NIC's Armada 3720 Secure Firmware v2022.06.11 (Aug 1 2022 19:01:52)
Running on ESPRESSObin Ultra
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v2.7(release):v2.7.0-211-g1d867c14c
NOTICE: BL1: Built : 19:03:59, Aug 1 2022
NOTICE: BL1: Booting BL2
NOTICE: BL2: v2.7(release):v2.7.0-211-g1d867c14c
NOTICE: BL2: Built : 19:03:59, Aug 1 2022
NOTICE: BL1: Booting BL31
NOTICE: BL31: v2.7(release):v2.7.0-211-g1d867c14c
NOTICE: BL31: Built : 19:04:01, Aug 1 2022
U-Boot 2021.04-rc2-00171-ga76965aff7 (Feb 26 2021 - 15:20:15 +0100)
DRAM: 1 GiB
Comphy-0: USB3_HOST0 5 Gbps
Comphy-1: PEX0 2.5 Gbps
Comphy-2: SATA0 5 Gbps
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
PCIE-0: Link up
MMC: sdhci@d8000: 0
Loading Environment from SPIFlash... SF: Detected mx25u3235f with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Model: Globalscale Marvell ESPRESSOBin Ultra Board
Net: eth0: neta@30000 [PRIME]
Autoboot in 2 seconds, to stop use 's' key
=> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 192.168.2.29 (2310 ms)
*** Warning: no boot file name; using 'C0A8021D.img'
Using neta@30000 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.29
Filename 'C0A8021D.img'.
Load address: 0x7000000
Loading: *
TFTP error: 'permission denied!' (0)
Starting again
=> tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
Using neta@30000 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.29
Filename 'openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin'.
Load address: 0x7000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####################
5.4 MiB/s
done
Bytes transferred = 21276680 (144a808 hex)
=> tftpboot $fdt_addr_r image-armada-3720-espressobin-ultra.dtb
Using neta@30000 device
TFTP from server 192.168.2.1; our IP address is 192.168.2.29
Filename 'image-armada-3720-espressobin-ultra.dtb'.
Load address: 0x6f00000
Loading: #
3.9 MiB/s
done
Bytes transferred = 12254 (2fde hex)
=> booti $kernel_addr_r - $fdt_addr_r
## Flattened Device Tree blob at 06f00000
Booting using the fdt blob at 0x6f00000
Using Device Tree in place at 0000000006f00000, end 0000000006f05fdd
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.15.58 (robimarko@fedora) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20023+197-21825af2da) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Aug 1 17:16:02 2022
[ 0.000000] Machine model: Globalscale Marvell ESPRESSOBin Ultra Board
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] node 0: [mem 0x0000000004000000-0x00000000041fffff]
[ 0.000000] node 0: [mem 0x0000000004200000-0x000000003fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 16 pages/cpu s25816 r8192 d31528 u65536
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048
[ 0.000000] Kernel command line:
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1005216K/1048576K available (8128K kernel code, 874K rwdata, 2104K rodata, 9536K init, 275K bss, 43360K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 192 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
[ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000000] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.000117] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
[ 0.000129] pid_max: default: 32768 minimum: 301
[ 0.000263] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000281] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.001626] rcu: Hierarchical SRCU implementation.
[ 0.001780] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.002035] smp: Bringing up secondary CPUs ...
[ 0.002437] Detected VIPT I-cache on CPU1
[ 0.002472] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
[ 0.002517] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.002612] smp: Brought up 1 node, 2 CPUs
[ 0.002625] SMP: Total of 2 processors activated.
[ 0.002631] CPU features: detected: 32-bit EL0 Support
[ 0.002636] CPU features: detected: CRC32 instructions
[ 0.002669] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.002676] CPU: All CPU(s) started at EL2
[ 0.002689] alternatives: patching kernel code
[ 0.005134] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.005169] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.005303] pinctrl core: initialized pinctrl subsystem
[ 0.006033] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.006376] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.006415] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.006454] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.006717] thermal_sys: Registered thermal governor 'step_wise'
[ 0.007014] cpuidle: using governor ladder
[ 0.007048] ASID allocator initialised with 65536 entries
[ 0.016789] cryptd: max_cpu_qlen set to 1000
[ 0.018595] SCSI subsystem initialized
[ 0.018972] usbcore: registered new interface driver usbfs
[ 0.019003] usbcore: registered new interface driver hub
[ 0.019034] usbcore: registered new device driver usb
[ 0.020167] clocksource: Switched to clocksource arch_sys_counter
[ 0.020685] NET: Registered PF_INET protocol family
[ 0.020859] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.021455] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.021484] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.021496] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.021557] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 0.021697] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.021826] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.021855] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.022006] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.022035] PCI: CLS 0 bytes, default 64
[ 0.040335] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.043515] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.043537] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.048368] advk-pcie d0070000.pcie: host bridge /soc/pcie@d0070000 ranges:
[ 0.048426] advk-pcie d0070000.pcie: MEM 0x00e8000000..0x00efefffff -> 0x00e8000000
[ 0.048443] advk-pcie d0070000.pcie: IO 0x00efff0000..0x00efffffff -> 0x0000000000
[ 0.050416] mv_xor d0060900.xor: Marvell shared XOR driver
[ 0.110878] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.170850] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.171025] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present!
[ 0.171208] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.171721] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.176087] loop: module loaded
[ 0.177362] ahci-mvebu d00e0000.sata: supply ahci not found, using dummy regulator
[ 0.177546] ahci-mvebu d00e0000.sata: supply phy not found, using dummy regulator
[ 0.179834] spi-nor spi0.0: mx25u3235f (4096 Kbytes)
[ 0.184298] 3 fixed-partitions partitions found on MTD device spi0.0
[ 0.184335] Creating 3 MTD partitions on "spi0.0":
[ 0.184346] 0x000000000000-0x0000003e0000 : "firmware"
[ 0.184776] 0x0000003e0000-0x0000003f0000 : "hw-info"
[ 0.185133] 0x0000003f0000-0x000000400000 : "u-boot-env"
[ 0.193060] hwmon hwmon0: temp1_input not attached to any thermal zone
[ 0.193611] mv88e6085 d0032004.mdio-mii:03: switch 0x3410 detected: Marvell 88E6341, revision 0
[ 0.211806] hwmon hwmon1: temp1_input not attached to any thermal zone
[ 0.219857] hwmon hwmon2: temp1_input not attached to any thermal zone
[ 0.227923] hwmon hwmon3: temp1_input not attached to any thermal zone
[ 0.236011] hwmon hwmon4: temp1_input not attached to any thermal zone
[ 0.245159] mvneta d0030000.ethernet eth0: Using hardware mac address 00:51:82:11:22:00
[ 0.245482] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.245498] ehci-platform: EHCI generic platform driver
[ 0.245666] ehci-orion: EHCI orion driver
[ 0.245950] orion-ehci d005e000.usb: EHCI Host Controller
[ 0.245985] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
[ 0.246112] orion-ehci d005e000.usb: irq 22, io mem 0xd005e000
[ 0.270184] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
[ 0.270644] hub 1-0:1.0: USB hub found
[ 0.270683] hub 1-0:1.0: 1 port detected
[ 0.271625] usbcore: registered new interface driver usb-storage
[ 0.271812] i2c_dev: i2c /dev entries driver
[ 0.272532] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec
[ 0.272985] sdhci: Secure Digital Host Controller Interface driver
[ 0.273005] sdhci: Copyright(c) Pierre Ossman
[ 0.273071] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.274990] NET: Registered PF_INET6 protocol family
[ 0.277969] Segment Routing with IPv6
[ 0.278018] In-situ OAM (IOAM) with IPv6
[ 0.278072] NET: Registered PF_PACKET protocol family
[ 0.278307] 8021q: 802.1Q VLAN Support v1.8
[ 0.282038] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart
[ 0.300173] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA
[ 0.306448] printk: console [ttyMV0] enabled
[ 1.152576] usb_phy_generic usb3-phy: dummy supplies not allowed for exclusive requests
[ 1.161561] advk-pcie d0070000.pcie: host bridge /soc/pcie@d0070000 ranges:
[ 1.168797] advk-pcie d0070000.pcie: MEM 0x00e8000000..0x00efefffff -> 0x00e8000000
[ 1.177183] advk-pcie d0070000.pcie: IO 0x00efff0000..0x00efffffff -> 0x0000000000
[ 1.258630] mmc0: new HS400 MMC card at address 0001
[ 1.264632] mmcblk0: mmc0:0001 DG4008 7.28 GiB
[ 1.270317] mmcblk0: p1 p2
[ 1.274047] mmcblk0boot0: mmc0:0001 DG4008 4.00 MiB
[ 1.280026] mmcblk0boot1: mmc0:0001 DG4008 4.00 MiB
[ 1.285539] mmcblk0rpmb: mmc0:0001 DG4008 4.00 MiB, chardev (248:0)
[ 1.290201] advk-pcie d0070000.pcie: link up
[ 1.296564] advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
[ 1.303100] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.308771] pci_bus 0000:00: root bus resource [mem 0xe8000000-0xefefffff]
[ 1.315871] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 1.322287] pci 0000:00:00.0: [11ab:0100] type 01 class 0x060400
[ 1.329316] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.337797] pci 0000:01:00.0: [1b4b:2b42] type 00 class 0x020000
[ 1.344081] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.351577] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.359105] pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 128 (was 512, max 512)
[ 1.368001] pci 0000:01:00.0: Max Payload Size set to 128 (was 128, max 128)
[ 1.375504] pci 0000:01:00.0: supports D1 D2
[ 1.379905] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[ 1.386537] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.402662] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.409528] pci 0000:00:00.0: BAR 9: assigned [mem 0xe8000000-0xe81fffff 64bit pref]
[ 1.417538] pci 0000:01:00.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit pref]
[ 1.425564] pci 0000:01:00.0: BAR 2: assigned [mem 0xe8100000-0xe81fffff 64bit pref]
[ 1.433585] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.438706] pci 0000:00:00.0: bridge window [mem 0xe8000000-0xe81fffff 64bit pref]
[ 1.447124] ahci-mvebu d00e0000.sata: supply ahci not found, using dummy regulator
[ 1.455113] ahci-mvebu d00e0000.sata: supply phy not found, using dummy regulator
[ 1.462992] ahci-mvebu d00e0000.sata: supply target not found, using dummy regulator
[ 1.471733] ahci-mvebu d00e0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 1.481084] ahci-mvebu d00e0000.sata: flags: ncq sntf led only pmp fbs pio slum part sxs
[ 1.490430] scsi host0: ahci-mvebu
[ 1.494204] ata1: SATA max UDMA/133 mmio [mem 0xd00e0000-0xd00e0177] port 0x100 irq 31
[ 1.503002] mv88e6085 d0032004.mdio-mii:03: switch 0x3410 detected: Marvell 88E6341, revision 0
[ 1.530210] hwmon hwmon1: temp1_input not attached to any thermal zone
[ 1.545037] hwmon hwmon2: temp1_input not attached to any thermal zone
[ 1.559853] hwmon hwmon3: temp1_input not attached to any thermal zone
[ 1.574804] hwmon hwmon4: temp1_input not attached to any thermal zone
[ 1.630197] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1.831320] hub 1-1:1.0: USB hub found
[ 1.831412] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.835395] hub 1-1:1.0: 4 ports detected
[ 2.260168] usb 1-1.3: new high-speed USB device number 3 using orion-ehci
[ 2.394972] mv88e6085 d0032004.mdio-mii:03 lan0 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:11] driver [Marvell 88E6341 Family] (irq=62)
[ 2.494975] mv88e6085 d0032004.mdio-mii:03 lan1 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:12] driver [Marvell 88E6341 Family] (irq=63)
[ 2.594980] mv88e6085 d0032004.mdio-mii:03 lan2 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:13] driver [Marvell 88E6341 Family] (irq=64)
[ 2.694973] mv88e6085 d0032004.mdio-mii:03 lan3 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:14] driver [Marvell 88E6341 Family] (irq=65)
[ 2.790906] mv88e6085 d0032004.mdio-mii:03 wan (uninitialized): PHY [d0032004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL)
[ 2.803794] DSA: tree 0 setup
[ 2.814114] xhci-hcd d0058000.usb: xHCI Host Controller
[ 2.819542] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2
[ 2.827302] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010090
[ 2.836786] xhci-hcd d0058000.usb: irq 21, io mem 0xd0058000
[ 2.842751] xhci-hcd d0058000.usb: xHCI Host Controller
[ 2.848144] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3
[ 2.855785] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed
[ 2.862661] hub 2-0:1.0: USB hub found
[ 2.866568] hub 2-0:1.0: 1 port detected
[ 2.870910] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.879603] hub 3-0:1.0: USB hub found
[ 2.883556] hub 3-0:1.0: 1 port detected
[ 2.941643] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the BOARD_INFO command
[ 2.991627] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the ECDSA_PUB_KEY command
[ 3.111694] turris-mox-rwtm firmware:armada-3700-rwtm: HWRNG successfully registered
[ 3.191780] random: crng init done
[ 3.209519] Freeing unused kernel memory: 9536K
[ 3.230359] Run /init as init process
[ 3.417019] init: Console is alive
[ 3.421098] init: - watchdog -
[ 3.428362] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.438054] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.455303] init: - preinit -
[ 3.632411] mvneta d0030000.ethernet eth0: configuring for fixed/rgmii-id link mode
[ 3.641393] device eth0 entered promiscuous mode
[ 3.646384] mvneta d0030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 3.650978] mv88e6085 d0032004.mdio-mii:03 lan0: configuring for phy/ link mode
[ 3.665427] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.777567] device eth0 left promiscuous mode
[ 5.787552] procd: - early -
[ 5.790939] procd: - watchdog -
[ 6.340099] procd: - watchdog -
[ 6.345159] procd: - ubus -
[ 6.399899] procd: - init -
Please press Enter to activate this console.
[ 6.570871] urngd: v1.0.2 started.
[ 6.629923] kmodloader: loading kernel modules from /etc/modules.d/*
[ 6.638235] i2c i2c-0: PXA I2C adapter
[ 6.651690] rtc-pcf8563 0-0051: registered as rtc0
[ 6.657146] rtc-pcf8563 0-0051: setting system clock to 2022-08-02T16:04:08 UTC (1659456248)
[ 6.696107] PPP generic driver version 2.4.2
[ 6.701417] NET: Registered PF_PPPOX protocol family
[ 6.711064] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.517102] Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000007f90cecd28
[ 11.528167] Mem abort info:
[ 11.531042] ESR = 0x96000005
[ 11.534186] EC = 0x25: DABT (current EL), IL = 32 bits
[ 11.539661] SET = 0, FnV = 0
[ 11.542810] EA = 0, S1PTW = 0
[ 11.546070] FSC = 0x05: level 1 translation fault
[ 11.551126] Data abort info:
[ 11.554112] ISV = 0, ISS = 0x00000005
[ 11.558087] CM = 0, WnR = 0
[ 11.561170] user pgtable: 4k pages, 39-bit VAs, pgdp=00000000032f9000
[ 11.567848] [0000007f90cecd28] pgd=08000000016f4003, p4d=08000000016f4003, pud=08000000016f4003, pmd=0800000002ed8003, pte=00e0000006ff3fc3
[ 11.580870] Internal error: Oops: 96000005 [#1] SMP
[ 11.585933] Modules linked in: pppoe ppp_async nft_fib_inet nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_table_inet pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_objref nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_g
[ 11.636863] CPU: 1 PID: 1250 Comm: S20network Not tainted 5.15.58 #0
[ 11.643461] Hardware name: Globalscale Marvell ESPRESSOBin Ultra Board (DT)
[ 11.650671] pstate: 004000c5 (nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 11.657899] pc : __switch_to+0x38/0x114
[ 11.661914] lr : __switch_to+0x1c/0x114
[ 11.665909] sp : ffffffc00a3fbbd0
[ 11.669347] x29: ffffffc00a3fbbd0 x28: 0000000000000000 x27: 0000000000000000
[ 11.676776] x26: 0000000000000001 x25: 0000000000000080 x24: ffffff80009090e8
[ 11.684203] x23: 0000000000000000 x22: ffffff8000908b80 x21: 0000000000000000
[ 11.691629] x20: ffffff8000908b80 x19: ffffff80000c1700 x18: 0000000000000000
[ 11.699055] x17: 0000000000000000 x16: 0000000000000009 x15: 0000000000000000
[ 11.706480] x14: 0000000000000000 x13: ffffffc008807590 x12: 00000000d2a81d91
[ 11.713907] x11: 0000000000000242 x10: 0000000000000000 x9 : 0000000000000000
[ 11.721330] x8 : 0000000000000000 x7 : 0000000000000001 x6 : 000000002a92c9cc
[ 11.728753] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000007f90cecd28
[ 11.736176] x2 : ffffffc00944e000 x1 : 0000000000000001 x0 : 0000000000000000
[ 11.743603] Call trace:
[ 11.746147] __switch_to+0x38/0x114
[ 11.749788] __schedule+0x214/0x530
[ 11.753424] schedule+0x44/0xc4
[ 11.756696] pipe_read+0x2e8/0x3f0
[ 11.760251] new_sync_read+0x138/0x14c
[ 11.764166] vfs_read+0x120/0x1a0
[ 11.767632] ksys_read+0xbc/0xd0
[ 11.771006] __arm64_sys_read+0x18/0x20
[ 11.775008] invoke_syscall.constprop.0+0x58/0x100
[ 11.779991] do_el0_svc+0x48/0xe0
[ 11.783445] el0_svc+0x14/0x50
[ 11.786641] el0t_64_sync_handler+0x9c/0x120
[ 11.791092] el0t_64_sync+0x15c/0x160
[ 11.794924] Code: b9452841 f9048003 7100003f 5400056d (9000a1c0)
[ 11.801239] ---[ end trace c691b009998e359e ]---
[ 11.806030] Kernel panic - not syncing: Oops: Fatal exception
[ 11.811978] SMP: stopping secondary CPUs
[ 11.816052] Kernel Offset: disabled
[ 11.819667] CPU features: 0x00000000,20000802
[ 11.824188] Memory Limit: none
[ 11.827361] Rebooting in 3 seconds..
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment