gistfile1.txt

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.15.58 (robimarko@fedora) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20023+197-21825af2da) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Aug 1 17:16:02 2022
[    0.000000] Machine model: Globalscale Marvell ESPRESSOBin Ultra Board
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000003fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000]   node   0: [mem 0x0000000004000000-0x00000000041fffff]
[    0.000000]   node   0: [mem 0x0000000004200000-0x000000003fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 16 pages/cpu s25816 r8192 d31528 u65536
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 258048
[    0.000000] Kernel command line: 
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1005216K/1048576K available (8128K kernel code, 874K rwdata, 2108K rodata, 9536K init, 275K bss, 43360K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 192 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000d1d40000
[    0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[    0.000000] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
[    0.000117] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
[    0.000130] pid_max: default: 32768 minimum: 301
[    0.000265] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.000283] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.001626] rcu: Hierarchical SRCU implementation.
[    0.001779] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.002032] smp: Bringing up secondary CPUs ...
[    0.002430] Detected VIPT I-cache on CPU1
[    0.002465] GICv3: CPU1: found redistributor 1 region 0:0x00000000d1d60000
[    0.002510] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.002602] smp: Brought up 1 node, 2 CPUs
[    0.002616] SMP: Total of 2 processors activated.
[    0.002622] CPU features: detected: 32-bit EL0 Support
[    0.002628] CPU features: detected: CRC32 instructions
[    0.002663] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.002669] CPU: All CPU(s) started at EL2
[    0.002681] alternatives: patching kernel code
[    0.005156] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.005192] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.005324] pinctrl core: initialized pinctrl subsystem
[    0.006058] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.006401] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.006440] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.006480] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.006743] thermal_sys: Registered thermal governor 'step_wise'
[    0.007040] cpuidle: using governor ladder
[    0.007074] ASID allocator initialised with 65536 entries
[    0.016772] cryptd: max_cpu_qlen set to 1000
[    0.018573] SCSI subsystem initialized
[    0.018947] usbcore: registered new interface driver usbfs
[    0.018980] usbcore: registered new interface driver hub
[    0.019010] usbcore: registered new device driver usb
[    0.020147] clocksource: Switched to clocksource arch_sys_counter
[    0.020660] NET: Registered PF_INET protocol family
[    0.020831] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.021429] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.021459] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.021471] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.021532] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.021672] TCP: Hash tables configured (established 8192 bind 8192)
[    0.021802] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.021830] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.021983] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.022014] PCI: CLS 0 bytes, default 64
[    0.031628] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    0.034810] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.034832] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.044177] advk-pcie d0070000.pcie: host bridge /soc/pcie@d0070000 ranges:
[    0.044239] advk-pcie d0070000.pcie:      MEM 0x00e8000000..0x00efefffff -> 0x00e8000000
[    0.044256] advk-pcie d0070000.pcie:       IO 0x00efff0000..0x00efffffff -> 0x0000000000
[    0.046248] mv_xor d0060900.xor: Marvell shared XOR driver
[    0.100908] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[    0.160875] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[    0.161051] debugfs: Directory 'd0060900.xor' with parent 'dmaengine' already present!
[    0.161234] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.161737] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.164217] loop: module loaded
[    0.167636] ahci-mvebu d00e0000.sata: supply ahci not found, using dummy regulator
[    0.167831] ahci-mvebu d00e0000.sata: supply phy not found, using dummy regulator
[    0.169850] spi-nor spi0.0: mx25u3235f (4096 Kbytes)
[    0.174332] 3 fixed-partitions partitions found on MTD device spi0.0
[    0.174369] Creating 3 MTD partitions on "spi0.0":
[    0.174380] 0x000000000000-0x0000003e0000 : "firmware"
[    0.174760] 0x0000003e0000-0x0000003f0000 : "hw-info"
[    0.174982] 0x0000003f0000-0x000000400000 : "u-boot-env"
[    0.183968] hwmon hwmon0: temp1_input not attached to any thermal zone
[    0.184532] mv88e6085 d0032004.mdio-mii:03: switch 0x3410 detected: Marvell 88E6341, revision 0
[    0.201908] hwmon hwmon1: temp1_input not attached to any thermal zone
[    0.210035] hwmon hwmon2: temp1_input not attached to any thermal zone
[    0.218152] hwmon hwmon3: temp1_input not attached to any thermal zone
[    0.226577] hwmon hwmon4: temp1_input not attached to any thermal zone
[    0.235758] mvneta d0030000.ethernet eth0: Using hardware mac address 00:51:82:11:22:00
[    0.236015] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.236024] ehci-platform: EHCI generic platform driver
[    0.236135] ehci-orion: EHCI orion driver
[    0.236326] orion-ehci d005e000.usb: EHCI Host Controller
[    0.236347] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
[    0.236453] orion-ehci d005e000.usb: irq 22, io mem 0xd005e000
[    0.260188] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
[    0.260726] hub 1-0:1.0: USB hub found
[    0.260767] hub 1-0:1.0: 1 port detected
[    0.261706] usbcore: registered new interface driver usb-storage
[    0.261891] i2c_dev: i2c /dev entries driver
[    0.262609] armada_37xx_wdt d0008300.watchdog: Initial timeout 120 sec
[    0.263071] sdhci: Secure Digital Host Controller Interface driver
[    0.263090] sdhci: Copyright(c) Pierre Ossman
[    0.263157] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.265263] NET: Registered PF_INET6 protocol family
[    0.267153] Segment Routing with IPv6
[    0.267211] In-situ OAM (IOAM) with IPv6
[    0.267271] NET: Registered PF_PACKET protocol family
[    0.268028] 8021q: 802.1Q VLAN Support v1.8
[    0.271849] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 0, base_baud = 1562500) is a mvebu-uart
[    0.292851] mmc0: SDHCI controller on d00d8000.sdhci [d00d8000.sdhci] using ADMA
[    0.296232] printk: console [ttyMV0] enabled
[    0.375613] mmc0: new HS400 MMC card at address 0001
[    0.378057] usb_phy_generic usb3-phy: dummy supplies not allowed for exclusive requests
[    0.385464] mmcblk0: mmc0:0001 DG4008 7.28 GiB 
[    0.388594] advk-pcie d0070000.pcie: host bridge /soc/pcie@d0070000 ranges:
[    0.396661]  mmcblk0: p1 p2
[    0.401753] advk-pcie d0070000.pcie:      MEM 0x00e8000000..0x00efefffff -> 0x00e8000000
[    0.401772] advk-pcie d0070000.pcie:       IO 0x00efff0000..0x00efffffff -> 0x0000000000
[    0.406021] mmcblk0boot0: mmc0:0001 DG4008 4.00 MiB 
[    0.520153] advk-pcie d0070000.pcie: link up
[    0.520943] mmcblk0boot1: mmc0:0001 DG4008 4.00 MiB 
[    0.526608] advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
[    0.537882] mmcblk0rpmb: mmc0:0001 DG4008 4.00 MiB, chardev (248:0)
[    0.545865] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.700156] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    0.701546] pci_bus 0000:00: root bus resource [mem 0xe8000000-0xefefffff]
[    0.901310] hub 1-1:1.0: USB hub found
[    0.905700] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.912355] hub 1-1:1.0: 4 ports detected
[    0.915247] pci 0000:00:00.0: [11ab:0100] type 01 class 0x060400
[    1.255071] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.263549] pci 0000:01:00.0: [1b4b:2b42] type 00 class 0x020000
[    1.269818] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[    1.277316] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x000fffff 64bit pref]
[    1.284849] pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 128 (was 512, max 512)
[    1.293744] pci 0000:01:00.0: Max Payload Size set to 128 (was 128, max 128)
[    1.301242] pci 0000:01:00.0: supports D1 D2
[    1.305642] pci 0000:01:00.0: PME# supported from D0 D1 D3hot D3cold
[    1.312273] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    1.328378] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.335257] pci 0000:00:00.0: BAR 9: assigned [mem 0xe8000000-0xe81fffff 64bit pref]
[    1.340186] usb 1-1.3: new high-speed USB device number 3 using orion-ehci
[    1.343257] pci 0000:01:00.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit pref]
[    1.358359] pci 0000:01:00.0: BAR 2: assigned [mem 0xe8100000-0xe81fffff 64bit pref]
[    1.366379] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.371505] pci 0000:00:00.0:   bridge window [mem 0xe8000000-0xe81fffff 64bit pref]
[    1.379928] ahci-mvebu d00e0000.sata: supply ahci not found, using dummy regulator
[    1.387937] ahci-mvebu d00e0000.sata: supply phy not found, using dummy regulator
[    1.395818] ahci-mvebu d00e0000.sata: supply target not found, using dummy regulator
[    1.404554] ahci-mvebu d00e0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    1.413903] ahci-mvebu d00e0000.sata: flags: ncq sntf led only pmp fbs pio slum part sxs 
[    1.423239] scsi host0: ahci-mvebu
[    1.427011] ata1: SATA max UDMA/133 mmio [mem 0xd00e0000-0xd00e0177] port 0x100 irq 31
[    1.435849] mv88e6085 d0032004.mdio-mii:03: switch 0x3410 detected: Marvell 88E6341, revision 0
[    1.461614] hwmon hwmon1: temp1_input not attached to any thermal zone
[    1.476457] hwmon hwmon2: temp1_input not attached to any thermal zone
[    1.491353] hwmon hwmon3: temp1_input not attached to any thermal zone
[    1.506166] hwmon hwmon4: temp1_input not attached to any thermal zone
[    1.761372] ata1: SATA link down (SStatus 0 SControl 300)
[    2.314957] mv88e6085 d0032004.mdio-mii:03 lan0 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:11] driver [Marvell 88E6341 Family] (irq=62)
[    2.414965] mv88e6085 d0032004.mdio-mii:03 lan1 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:12] driver [Marvell 88E6341 Family] (irq=63)
[    2.514963] mv88e6085 d0032004.mdio-mii:03 lan2 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:13] driver [Marvell 88E6341 Family] (irq=64)
[    2.614987] mv88e6085 d0032004.mdio-mii:03 lan3 (uninitialized): PHY [!soc!internal-regs@d0000000!mdio@32004!switch0@1!mdio:14] driver [Marvell 88E6341 Family] (irq=65)
[    2.720886] mv88e6085 d0032004.mdio-mii:03 wan (uninitialized): PHY [d0032004.mdio-mii:01] driver [Marvell 88E1510] (irq=POLL)
[    2.733779] DSA: tree 0 setup
[    2.744125] xhci-hcd d0058000.usb: xHCI Host Controller
[    2.749555] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 2
[    2.757313] xhci-hcd d0058000.usb: hcc params 0x0a000998 hci version 0x100 quirks 0x0000000000010090
[    2.766800] xhci-hcd d0058000.usb: irq 21, io mem 0xd0058000
[    2.772765] xhci-hcd d0058000.usb: xHCI Host Controller
[    2.778160] xhci-hcd d0058000.usb: new USB bus registered, assigned bus number 3
[    2.785800] xhci-hcd d0058000.usb: Host supports USB 3.0 SuperSpeed
[    2.792677] hub 2-0:1.0: USB hub found
[    2.796584] hub 2-0:1.0: 1 port detected
[    2.800919] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.809613] hub 3-0:1.0: USB hub found
[    2.813541] hub 3-0:1.0: 1 port detected
[    2.869859] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the BOARD_INFO command
[    2.919738] turris-mox-rwtm firmware:armada-3700-rwtm: Firmware does not support the ECDSA_PUB_KEY command
[    3.039780] turris-mox-rwtm firmware:armada-3700-rwtm: HWRNG successfully registered
[    3.058513] cpu cpu0: OPP[0] freq 1200000000 uVolt 1213000
[    3.089894] cpu cpu0: OPP[1] freq 600000000 uVolt 1155000
[    3.090215] random: crng init done
[    3.095542] cpu cpu0: OPP[2] freq 300000000 uVolt 1073000
[    3.104598] cpu cpu0: OPP[3] freq 200000000 uVolt 1073000
[    3.110682] cpu cpu0: _set_opp: switching OPP: Freq 0 -> 200000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.141162] Freeing unused kernel memory: 9536K
[    3.146116] cpu cpu0: _set_opp: switching OPP: Freq 200000000 -> 1200000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.180184] Run /init as init process
[    3.270815] ------------[ cut here ]------------
[    3.275599] Kernel BUG at do_undefinstr+0x200/0x210 [verbose debug info unavailable]
[    3.283600] Internal error: Oops - BUG: 0 [#1] SMP
[    3.288539] Modules linked in:
[    3.291688] CPU: 1 PID: 468 Comm: cp Not tainted 5.15.58 #0
[    3.297434] Hardware name: Globalscale Marvell ESPRESSOBin Ultra Board (DT)
[    3.300185] cpu cpu0: _set_opp: switching OPP: Freq 1200000000 -> 200000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.304611] pstate: 00400005 (nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[    3.320271] cpu cpu0: _set_opp: switching OPP: Freq 200000000 -> 600000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.321471] pc : do_undefinstr+0x200/0x210
[    3.335311] lr : do_undefinstr+0x50/0x210
[    3.339454] sp : ffffffc00a30b9b0
[    3.342870] x29: ffffffc00a30b9b0 x28: ffffff8000e39700 x27: 0000000000000000
[    3.350246] x26: 0000000000000001 x25: ffffffc009384e98 x24: 0000000000000004
[    3.357621] x23: 0000000040400005 x22: ffffffc0081927d0 x21: 0000000007a13000
[    3.364995] x20: 0000000051401000 x19: ffffffc00a30ba20 x18: 0000000000000000
[    3.372369] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[    3.379743] x14: 0000000000000000 x13: 0000000000000000 x12: 0000007fbbf64028
[    3.380189] cpu cpu0: _set_opp: switching OPP: Freq 600000000 -> 200000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.387117] x11: 0000000000000000 x10: d0d0d0d0d0e4a7b6 x9 : 0000000000000000
[    3.400260] cpu cpu0: _set_opp: switching OPP: Freq 200000000 -> 600000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.404085] x8 : 5dbcdffffff0000e x7 : ffffff8000469a80 x6 : ffffff800072ede6
[    3.421100] x5 : 0000000000000000 x4 : ffffffc00937fe18 x3 : 00000000d5380000
[    3.428474] x2 : 0000000051400000 x1 : ffffffc00944e0e8 x0 : 0000000040400005
[    3.435850] Call trace:
[    3.438371]  do_undefinstr+0x200/0x210
[    3.442245]  el1_undef+0x28/0x44
[    3.445587]  el1h_64_sync_handler+0x80/0xc0
[    3.449909]  el1h_64_sync+0x78/0x7c
[    3.453510]  do_dentry_open+0x90/0x380
[    3.457387]  vfs_open+0x28/0x30
[    3.460173] cpu cpu0: _set_opp: switching OPP: Freq 600000000 -> 200000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.460631]  path_openat+0x948/0xddc
[    3.473914]  do_filp_open+0x6c/0x100
[    3.477634]  do_sys_openat2+0x8c/0x14c
[    3.480259] cpu cpu0: _set_opp: switching OPP: Freq 200000000 -> 600000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.481544]  __arm64_sys_openat+0x54/0x7c
[    3.495293]  invoke_syscall.constprop.0+0x58/0x100
[    3.500242]  do_el0_svc+0x48/0xe0
[    3.503664]  el0_svc+0x14/0x50
[    3.506820]  el0t_64_sync_handler+0x9c/0x120
[    3.511232]  el0t_64_sync+0x15c/0x160
[    3.515020] Code: 17ffffd4 a9425bf5 17ffffc4 a9025bf5 (d4210000) 
[    3.521310] ---[ end trace 33c20789c4b5d61d ]---
[    3.526075] Kernel panic - not syncing: Oops - BUG: Fatal exception
[    3.530165] cpu cpu0: _set_opp: switching OPP: Freq 600000000 -> 200000000 Hz, Level 0 -> 0, Bw 0 -> 0
[    3.532539] SMP: stopping secondary CPUs
[    3.546192] Kernel Offset: disabled
[    3.549806] CPU features: 0x00000000,20000802
[    3.554327] Memory Limit: none
[    3.557500] Rebooting in 1 seconds..