Created
October 23, 2017 17:36
-
-
Save robimarko/63e0b114dc7c785b905cb194b0483d70 to your computer and use it in GitHub Desktop.
CPE210v2 LEDE 4.9.57
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
U-Boot 1.1.4-g30d8afa8-dirty (Nov 1 2016 - 17:38:05) | |
ap143-2.0 - Honey Bee 2.0 | |
DRAM: 64 MB | |
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x17 | |
flash size 8MB, sector count = 128 | |
Flash: 8 MB | |
Using default environment | |
In: serial | |
Out: serial | |
Err: serial | |
Net: ath_gmac_enet_initialize... | |
ath_gmac_enet_initialize: reset mask:c02200 | |
Scorpion ---->S27 PHY* | |
S27 reg init | |
: cfg1 0x800c0000 cfg2 0x7114 | |
eth0: ba:be:fa:ce:08:41 | |
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10 | |
eth0 up | |
Honey Bee ----> MAC 1 S27 PHY * | |
S27 reg init | |
ATHRS27: resetting s27 | |
ATHRS27: s27 reset done | |
: cfg1 0x800c0000 cfg2 0x7214 | |
eth1: ba:be:fa:ce:08:41 | |
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10 | |
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10 | |
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10 | |
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10 | |
eth1 up | |
eth0, eth1 | |
Setting 0x181162c0 to 0x50a1a100 | |
is button pressed? 1 | |
eth1 link down | |
enet0 port4 up | |
dup 1 speed 100 | |
Using eth0 device | |
TFTP from server 192.168.0.100; our IP address is 192.168.0.254 | |
Filename 'recovery.bin'. | |
Load address: 0x80060000 | |
Loading: ################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
################################################################# | |
########################### | |
done | |
Bytes transferred = 3462969 (34d739 hex) | |
Firmware recovery: FLASH_SIZE = 8 filesize = 0x34d739. | |
Reading Partition Table from NVRAM ... OK | |
Parsing Partition Table ... OK | |
File Length:3462969 | |
fw type name : . | |
Firmware process common. | |
Image verify OK! | |
Firmware file Verify ok! | |
[Error]sysmgr_cfg_checkSupportList(): 1063 @ productInfo CPE210(TP-LINK|EU|N300-2|00000000):2.0 NOT Match. | |
[Error]sysmgr_cfg_checkSupportList(): 1069 @ CPE210(TP-LINK|EU|N300-2|45550000):2.0 Matched!!! | |
Firmwave supports, check OK. | |
Firmware Recovery check ok! | |
Firmware Checking Passed. | |
######################################################### | |
Done. | |
All Done! | |
U-Boot 1.1.4-g30d8afa8-dirty (Nov 1 2016 - 17:38:05) | |
ap143-2.0 - Honey Bee 2.0 | |
DRAM: 64 MB | |
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x17 | |
flash size 8MB, sector count = 128 | |
Flash: 8 MB | |
Using default environment | |
In: serial | |
Out: serial | |
Err: serial | |
Net: ath_gmac_enet_initialize... | |
ath_gmac_enet_initialize: reset mask:c02200 | |
Scorpion ---->S27 PHY* | |
S27 reg init | |
: cfg1 0x800c0000 cfg2 0x7114 | |
eth0: ba:be:fa:ce:08:41 | |
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10 | |
eth0 up | |
Honey Bee ----> MAC 1 S27 PHY * | |
S27 reg init | |
ATHRS27: resetting s27 | |
ATHRS27: s27 reset done | |
: cfg1 0x800c0000 cfg2 0x7214 | |
eth1: ba:be:fa:ce:08:41 | |
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10 | |
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10 | |
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10 | |
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000 | |
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10 | |
eth1 up | |
eth0, eth1 | |
Setting 0x181162c0 to 0x50a1a100 | |
is button pressed? 0 | |
Autobooting in 1 seconds | |
## Booting image at 9f040000 ... | |
Uncompressing Kernel Image ... OK | |
Starting kernel ... | |
[ 0.000000] Linux version 4.9.57 (robimarko@Builder) (gcc version 6.3.0 (LEDE GCC 6.3.0 r5128+8-49fa574) ) #0 Mon Oct 23 15:08:52 2017 | |
[ 0.000000] bootconsole [early0] enabled | |
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) | |
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 | |
[ 0.000000] Determined physical RAM map: | |
[ 0.000000] memory: 04000000 @ 00000000 (usable) | |
[ 0.000000] Initrd not found or empty - disabling initrd | |
[ 0.000000] OF: fdt:No valid device tree found, continuing without | |
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. | |
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes | |
[ 0.000000] Zone ranges: | |
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] | |
[ 0.000000] Movable zone start for each node | |
[ 0.000000] Early memory node ranges | |
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] | |
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] | |
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 | |
[ 0.000000] Kernel command line: board=CPE210V2 mtdparts=spi0.0:128k(u-boot)ro,64k(pation-table)ro,64k(product-info)ro,1536k(kernel),6144k(rootfs),192k(config)ro,64k(ART)ro,7680k@0x40000(firmware) console=ttyS0,115200 rootfstype=squashfs noinitrd | |
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) | |
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) | |
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) | |
[ 0.000000] Writing ErrCtl register=00000000 | |
[ 0.000000] Readback ErrCtl register=00000000 | |
[ 0.000000] Memory: 59768K/65536K available (3216K kernel code, 168K rwdata, 820K rodata, 332K init, 213K bss, 5768K reserved, 0K cma-reserved) | |
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 | |
[ 0.000000] NR_IRQS:51 | |
[ 0.000000] Clocks: CPU:650.000MHz, DDR:392.187MHz, AHB:216.666MHz, Ref:25.000MHz | |
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns | |
[ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns | |
[ 0.008272] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) | |
[ 0.071121] pid_max: default: 32768 minimum: 301 | |
[ 0.076117] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.083092] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.093782] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns | |
[ 0.104202] futex hash table entries: 256 (order: -1, 3072 bytes) | |
[ 0.111358] NET: Registered protocol family 16 | |
[ 0.117903] MIPS: machine is TP-LINK CPE210 v2 | |
[ 0.374255] clocksource: Switched to clocksource MIPS | |
[ 0.380898] NET: Registered protocol family 2 | |
[ 0.386481] TCP established hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.393855] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) | |
[ 0.400643] TCP: Hash tables configured (established 1024 bind 1024) | |
[ 0.407495] UDP hash table entries: 256 (order: 0, 4096 bytes) | |
[ 0.413674] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) | |
[ 0.420658] NET: Registered protocol family 1 | |
[ 0.430300] Crashlog allocated RAM at address 0x3f00000 | |
[ 0.437122] workingset: timestamp_bits=30 max_order=14 bucket_order=0 | |
[ 0.451149] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
[ 0.457352] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | |
[ 0.477960] io scheduler noop registered | |
[ 0.482104] io scheduler deadline registered (default) | |
[ 0.488073] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled | |
[ 0.495320] console [ttyS0] disabled | |
[ 0.519255] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A | |
[ 0.528365] console [ttyS0] enabled | |
[ 0.528365] console [ttyS0] enabled | |
[ 0.535919] bootconsole [early0] disabled | |
[ 0.535919] bootconsole [early0] disabled | |
[ 0.549023] m25p80 spi0.0: found gd25q64, expected m25p80 | |
[ 0.557290] m25p80 spi0.0: gd25q64 (8192 Kbytes) | |
[ 0.562120] 8 cmdlinepart partitions found on MTD device spi0.0 | |
[ 0.568290] Creating 8 MTD partitions on "spi0.0": | |
[ 0.573250] 0x000000000000-0x000000020000 : "u-boot" | |
[ 0.580205] 0x000000020000-0x000000030000 : "pation-table" | |
[ 0.587887] 0x000000030000-0x000000040000 : "product-info" | |
[ 0.595531] 0x000000040000-0x0000001c0000 : "kernel" | |
[ 0.602503] 0x0000001c0000-0x0000007c0000 : "rootfs" | |
[ 0.609619] mtd: device 4 (rootfs) set to be root filesystem | |
[ 0.615613] 1 squashfs-split partitions found on MTD device rootfs | |
[ 0.622013] 0x0000003b0000-0x0000007c0000 : "rootfs_data" | |
[ 0.629548] 0x0000007c0000-0x0000007f0000 : "config" | |
[ 0.636717] 0x0000007f0000-0x000000800000 : "ART" | |
[ 0.643479] 0x000000040000-0x0000007c0000 : "firmware" | |
[ 0.651992] libphy: Fixed MDIO Bus: probed | |
[ 0.681864] libphy: ag71xx_mdio: probed | |
[ 1.317212] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] | |
[ 1.327500] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII | |
[ 1.335653] NET: Registered protocol family 10 | |
[ 1.344424] NET: Registered protocol family 17 | |
[ 1.349219] 8021q: 802.1Q VLAN Support v1.8 | |
[ 1.362135] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. | |
[ 1.372329] Freeing unused kernel memory: 332K | |
[ 1.376971] This architecture does not have kernel memory protection. | |
[ 2.057085] init: Console is alive | |
[ 2.060887] init: - watchdog - | |
[ 2.464253] random: fast init done | |
[ 2.981296] kmodloader: loading kernel modules from /etc/modules-boot.d/* | |
[ 3.061360] usbcore: registered new interface driver usbfs | |
[ 3.067210] usbcore: registered new interface driver hub | |
[ 3.072814] usbcore: registered new device driver usb | |
[ 3.085125] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
[ 3.093965] ehci-platform: EHCI generic platform driver | |
[ 3.103088] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
[ 3.111245] ohci-platform: OHCI generic platform driver | |
[ 3.117592] kmodloader: done loading kernel modules from /etc/modules-boot.d/* | |
[ 3.135708] init: - preinit - | |
[ 3.894562] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready | |
Press the [f] key and hit [enter] to enter failsafe mode | |
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | |
[ 6.017781] eth0: link up (100Mbps/Full duplex) | |
[ 6.022520] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready | |
[ 7.061404] mount_root: jffs2 not ready yet, using temporary tmpfs overlay | |
[ 7.100119] urandom-seed: Seed file not found (/etc/urandom.seed) | |
[ 7.287546] eth0: link down | |
[ 7.304214] procd: - early - | |
[ 7.308279] procd: - watchdog - | |
[ 7.931100] procd: - watchdog - | |
[ 7.934762] procd: - ubus - | |
[ 8.047877] procd: - init - | |
Please press Enter to activate this console. | |
[ 8.379374] kmodloader: loading kernel modules from /etc/modules.d/* | |
[ 8.391770] ip6_tables: (C) 2000-2006 Netfilter Core Team | |
[ 8.412856] Loading modules backported from Linux version wt-2017-10-06-0-ga7a22fbbd1f0 | |
[ 8.421211] Backport generated by backports.git v4.14-rc2-1-6-gedfb595c | |
[ 8.431775] ip_tables: (C) 2000-2006 Netfilter Core Team | |
[ 8.447982] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) | |
[ 8.524152] xt_time: kernel timezone is -0000 | |
[ 8.598222] PPP generic driver version 2.4.2 | |
[ 8.605764] NET: Registered protocol family 24 | |
[ 8.683644] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47 | |
[ 8.793883] kmodloader: done loading kernel modules from /etc/modules.d/* | |
[ 15.335873] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 | |
[ 15.343009] jffs2_build_filesystem(): unlocking the mtd device... [ 15.364368] done. | |
[ 15.366389] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 20.106563] br-lan: port 1(eth0) entered blocking state | |
[ 20.111982] br-lan: port 1(eth0) entered disabled state | |
[ 20.117912] device eth0 entered promiscuous mode | |
[ 20.191801] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready | |
[ 22.177774] eth0: link up (100Mbps/Full duplex) | |
[ 22.182531] br-lan: port 1(eth0) entered blocking state | |
[ 22.187971] br-lan: port 1(eth0) entered forwarding state | |
[ 22.235234] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready | |
[ 38.444502] done. | |
[ 38.446555] jffs2: notice: (873) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. | |
) |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment