Skip to content

Instantly share code, notes, and snippets.

@robimarko

robimarko/gist:688c1e0f8f462000e7f6c2911dac2f18

Created May 9, 2018 21:47
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save robimarko/688c1e0f8f462000e7f6c2911dac2f18 to your computer and use it in GitHub Desktop.
Save robimarko/688c1e0f8f462000e7f6c2911dac2f18 to your computer and use it in GitHub Desktop.
Download ZIP
Orbi-upstream-sdhci
Raw
gistfile1.txt
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110
S - IMAGE_VARIANT_STRING=DAAAANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000023
S - Reset status Config, 0x00000000
S - Core 0 Frequency, 0 MHz
B - 262 - PBL, Start
B - 1343 - bootable_media_detect_entry, Start
B - 39963 - bootable_media_detect_success, Start
B - 39977 - elf_loader_entry, Start
B - 42172 - auth_hash_seg_entry, Start
B - 44346 - auth_hash_seg_exit, Start
B - 79499 - elf_segs_hash_verify_entry, Start
B - 194992 - PBL, End
B - 195016 - SBL1, Start
B - 287219 - pm_device_init, Start
D - 9 - pm_device_init, Delta
B - 288738 - boot_flash_init, Start
D - 37282 - boot_flash_init, Delta
B - 330327 - boot_config_data_table_init, Start
D - 2749 - boot_config_data_table_init, Delta - (419 Bytes)
B - 338030 - clock_init, Start
D - 7537 - clock_init, Delta
B - 349338 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B - 352744 - sbl1_ddr_set_params, Start
B - 357839 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 362222 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13172 - sbl1_ddr_set_params, Delta
B - 375518 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 446901 - sbl1_wait_for_ddr_training, Start
D - 28 - sbl1_wait_for_ddr_training, Delta
B - 463111 - Image Load, Start
D - 14667 - QSEE Image Loaded, Delta - (268920 Bytes)
B - 478209 - Image Load, Start
D - 899 - SEC Image Loaded, Delta - (0 Bytes)
B - 488063 - Image Load, Start
D - 12638 - APPSBL Image Loaded, Delta - (421607 Bytes)
B - 501128 - QSEE Execution, Start
D - 60 - QSEE Execution, Delta
B - 507308 - SBL1, End
D - 314405 - SBL1, Delta
S - Flash Throughput, 25527 KB/s (691298 Bytes, 27080 us)
S - DDR Frequency, 672 MHz
U-Boot 2012.07-g9274bc2-dirty [Barrier Breaker unknown,unknown] (Jun 16 2017 - 16:27:21)
U-boot dni1 V1.1 for DNI HW ID: 29765352; NOR flash 0MB; EMMC flash 4096MB; RAM 512MB
smem ram ptable found: ver: 1 len: 3
DRAM: 512 MiB
machid : 0x8010001
NAND: ID = 0
Vendor = 0
Device = 0
Nand Flash error. Status = 64
ONFI Read id cmd failed
ONFI probe failed
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
0 MiB
MMC: qca_mmc: 0
*** Warning - bad CRC, using default environment
PCI0 Link Intialized
In: serial
Out: serial
Err: serial
Valid chip addresses: 27 48
machid: 8010001
flash_type: 1
Net: MAC0 addr:b0:39:56:8d:59:69
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
Hit any key to stop autoboot: 0
(IPQ40xx) # setenv serverip 192.168.2.213
(IPQ40xx) # setenv ipaddr 192.168.2.233
(IPQ40xx) # tftpboot openwrt-ipq40xx-netgear_orbipro-initramfs-fit-uImage.itb
eth0 PHY0 up Speed :1000 Full duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
TFTP from server 192.168.2.213; our IP address is 192.168.2.233
Filename 'openwrt-ipq40xx-netgear_orbipro-initramfs-fit-uImage.itb'.
Load address: 0x84000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
########################################################
done
Bytes transferred = 7488980 (7245d4 hex)
(IPQ40xx) # bootm
## Booting kernel from FIT Image at 84000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-4.14.37
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x840000e4
Data Size: 7452096 Bytes = 7.1 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: 53613c96
Hash algo: sha1
Hash value: dc7dc675aee50bf3f9cf25da6b3e5073f3a8253f
Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM OpenWrt netgear_orbipro device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8471b7e0
Data Size: 35010 Bytes = 34.2 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 2c04f2b8
Hash algo: sha1
Hash value: f5b80ec565d07596ce2b814112439c696d6a9d1b
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8471b7e0
Uncompressing Kernel Image ... OK
Loading Device Tree to 871e4000, end 871ef8c1 ... OK
Using machid 0x8010001 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.37 (robimarko@localhost.localdomain) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6914-aaddb4d2c8)) #0 SMP Wed May 9 21:34:54 2018
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear Orbi Pro
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x3c0 with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu @dfba0000 s29260 r8192 d23988 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129536
[ 0.000000] Kernel command line:
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 500532K/522240K available (4316K kernel code, 140K rwdata, 1216K rodata, 10240K init, 246K bss, 21708K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc07370c0 (5309 kB)
[ 0.000000] .init : 0xc0900000 - 0xc1300000 (10240 kB)
[ 0.000000] .data : 0xc1300000 - 0xc13233c0 ( 141 kB)
[ 0.000000] .bss : 0xc1325000 - 0xc1362874 ( 247 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[ 0.000021] Switching to timer-based delay loop, resolution 20ns
[ 0.000426] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[ 0.000446] pid_max: default: 32768 minimum: 301
[ 0.000582] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000597] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001178] CPU: Testing write buffer coherency: ok
[ 0.001781] Setting up static identity map for 0x80300000 - 0x80300060
[ 0.001907] Hierarchical SRCU implementation.
[ 0.002476] smp: Bringing up secondary CPUs ...
[ 0.004925] smp: Brought up 1 node, 4 CPUs
[ 0.004945] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.004952] CPU: All CPU(s) started in SVC mode.
[ 0.014046] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.014213] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.014236] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.014415] pinctrl core: initialized pinctrl subsystem
[ 0.015286] NET: Registered protocol family 16
[ 0.015532] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.016566] cpuidle: using governor ladder
[ 0.016609] cpuidle: using governor menu
[ 0.034313] msm_bus_fabric_init_driver
[ 0.034572] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.034588] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.034605] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1
[ 0.034643] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.034656] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.034670] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1
[ 0.092202] usbcore: registered new interface driver usbfs
[ 0.092277] usbcore: registered new interface driver hub
[ 0.092371] usbcore: registered new device driver usb
[ 0.092423] pps_core: LinuxPPS API ver. 1 registered
[ 0.092435] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.092459] PTP clock support registered
[ 0.093445] clocksource: Switched to clocksource arch_sys_counter
[ 0.094257] NET: Registered protocol family 2
[ 0.094858] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.094923] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.095012] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.095116] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.095152] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.095351] NET: Registered protocol family 1
[ 0.220336] No memory allocated for crashlog
[ 0.220496] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.223748] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.223763] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.228715] io scheduler noop registered
[ 0.228732] io scheduler deadline registered (default)
[ 0.229862] OF: PCI: host bridge /soc/pci@40000000 ranges:
[ 0.229898] OF: PCI: IO 0x40200000..0x402fffff -> 0x40200000
[ 0.229917] OF: PCI: MEM 0x40300000..0x406fffff -> 0x40300000
[ 0.443454] qcom-pcie 40000000.pci: link up
[ 0.443636] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00
[ 0.443658] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.443674] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x40200000-0x402fffff])
[ 0.443688] pci_bus 0000:00: root bus resource [mem 0x40300000-0x406fffff]
[ 0.444014] PCI: bus0: Fast back to back transfers disabled
[ 0.445115] PCI: bus1: Fast back to back transfers disabled
[ 0.445167] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff]
[ 0.445185] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit]
[ 0.445209] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit]
[ 0.445270] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.445287] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff]
[ 0.446047] pcieport 0000:00:00.0: AER enabled with IRQ 96
[ 0.448271] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[ 0.448355] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[ 0.448436] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[ 0.448511] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[ 0.448740] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.449308] msm_serial 78af000.serial: msm_serial: detected port #0
[ 0.449352] msm_serial 78af000.serial: uartclk = 1843200
[ 0.449402] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 26, base_baud = 115200) is a MSM
[ 0.449428] msm_serial: console setup on port #0
[ 1.093187] console [ttyMSM0] enabled
[ 1.098110] msm_serial: driver initialized
[ 1.105541] loop: module loaded
[ 1.106649] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 1.109542] libphy: ipq40xx_mdio: probed
[ 1.184394] ESS reset ok!
[ 1.217354] ESS reset ok!
[ 1.653875] libphy: Fixed MDIO Bus: probed
[ 1.754163] i2c /dev entries driver
[ 1.754398] i2c_qup 78b7000.i2c: using default clock-frequency 100000
[ 1.758748] sdhci: Secure Digital Host Controller Interface driver
[ 1.763060] sdhci: Copyright(c) Pierre Ossman
[ 1.769209] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.774160] sdhci_msm 7824900.sdhci: TCXO clk not present (-2)
[ 1.779304] sdhci_msm 7824900.sdhci: core clock boost failed
[ 1.823959] mmc0: Failed to set clock at rate 400000 at timing 0
[ 1.824281] mmc0: Failed to set clock at rate 400000 at timing 0
[ 1.854226] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.859959] mmc0: Failed to set clock at rate 400000 at timing 0
[ 1.863863] mmc0: Failed to set clock at rate 400000 at timing 0
[ 1.869669] mmc0: Failed to set clock at rate 400000 at timing 0
[ 1.873783] sdhci_msm 7824900.sdhci: card claims to support voltages below defined range
[ 1.879406] mmc0: Failed to set clock at rate 400000 at timing 0
[ 1.887751] mmc0: Failed to set clock at rate 400000 at timing 0
[ 1.897170] mmc0: Failed to set clock at rate 400000 at timing 0
[ 1.903886] NET: Registered protocol family 10
[ 1.906600] Segment Routing with IPv6
[ 1.909562] NET: Registered protocol family 17
[ 1.913593] 8021q: 802.1Q VLAN Support v1.8
[ 1.917596] Registering SWP/SWPB emulation handler
[ 1.923678] mmc0: error -110 whilst initialising M�[ 1.947283] Freeing unused kernel memory: 10240K
[ 1.956082] init: Console is alive
[ 1.956297] init: - watchdog -
[ 1.966232] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.403986] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.404576] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 2.410414] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x02010010
[ 2.417221] xhci-hcd xhci-hcd.0.auto: irq 131, io mem 0x08a00000
[ 2.426679] hub 1-0:1.0: USB hub found
[ 2.431018] hub 1-0:1.0: 1 port detected
[ 2.434864] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.438628] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 2.444070] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.452001] hub 2-0:1.0: USB hub found
[ 2.459879] hub 2-0:1.0: 1 port detected
[ 2.584220] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.584780] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 2.590587] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x02010010
[ 2.597584] xhci-hcd xhci-hcd.1.auto: irq 132, io mem 0x06000000
[ 2.606827] hub 3-0:1.0: USB hub found
[ 2.611261] hub 3-0:1.0: 1 port detected
[ 2.615183] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.618862] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 2.624355] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.632395] hub 4-0:1.0: USB hub found
[ 2.640145] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 2.644899] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.653719] init: - preinit -
[ 2.777481] random: jshn: uninitialized urandom read (4 bytes read)
[ 2.804409] random: jshn: uninitialized urandom read (4 bytes read)
[ 2.817102] random: jshn: uninitialized urandom read (4 bytes read)
/bin/board_detect: line 12: Unsupported: not found
[ 2.852503] random: jshn: uninitialized urandom read (4 bytes read)
[ 2.864229] random: jshn: uninitialized urandom read (4 bytes read)
[ 2.895959] random: jshn: uninitialized urandom read (4 bytes read)
[ 2.921635] random: jshn: uninitialized urandom read (4 bytes read)
[ 2.936762] random: jshn: uninitialized urandom read (4 bytes read)
[ 2.960651] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2.960742] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.109663] procd: - early -
[ 6.109796] procd: - watchdog -
[ 6.764603] procd: - watchdog -
[ 6.767322] procd: - ubus -
[ 6.779038] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.829538] random: ubusd: uninitialized urandom read (4 bytes read)
[ 6.840673] procd: - init -
Please press Enter to activate this console.
[ 6.971006] kmodloader: loading kernel modules from /etc/modules.d/*
[ 6.974625] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.366427] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 7.366463] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.374726] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.735487] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 7.957680] xt_time: kernel timezone is -0000
[ 8.220921] PPP generic driver version 2.4.2
[ 8.222105] NET: Registered protocol family 24
[ 8.234416] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 8.234914] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 8.406126] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[ 8.406211] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.447069] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 8.447431] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[ 8.455007] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.558055] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 8.558361] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2
[ 8.565670] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.640842] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 8.643095] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 8.648840] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 8.662877] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00053 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 4c56a386
[ 10.915231] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0046,subsystem-vendor=168c,subsystem-device=cafe,variant=Netgear-Orbi-Pr from ath10k/QCA9984/hw1.0/board-2.bin
[ 10.915414] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/board.bin failed with error -2
[ 10.932524] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 10.978252] firmware ath10k!QCA9984!hw1.0!board.bin: firmware_loading_store: map pages failed
[ 10.978510] ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9984/hw1.0
[ 10.985857] ath10k_pci 0000:01:00.0: failed to fetch board file: -11
[ 10.995195] ath10k_pci 0000:01:00.0: could not probe fw (-11)
[ 11.176447] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a000000.wifi.bin failed with error -2
[ 11.176499] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.241410] firmware ath10k!pre-cal-ahb-a000000.wifi.bin: firmware_loading_store: map pages failed
[ 11.241769] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/cal-ahb-a000000.wifi.bin failed with error -2
[ 11.249409] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.333608] firmware ath10k!cal-ahb-a000000.wifi.bin: firmware_loading_store: map pages failed
[ 11.333902] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 11.341139] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.402264] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 11.404028] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 11.410149] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 11.424208] ath10k_ahb a000000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67
[ 11.445319] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=Netgear-Orbi-Pr from ath10k/QCA4019/hw1.0/board-2.bin
[ 11.445468] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/board.bin failed with error -2
[ 11.462598] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.509068] firmware ath10k!QCA4019!hw1.0!board.bin: firmware_loading_store: map pages failed
[ 11.509323] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[ 11.516686] ath10k_ahb a000000.wifi: failed to fetch board file: -11
[ 11.526014] ath10k_ahb a000000.wifi: could not probe fw (-11)
[ 11.713471] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a800000.wifi.bin failed with error -2
[ 11.714314] ath10k_ahb a800000.wifi: Falling back to user helper
[ 11.773682] firmware ath10k!pre-cal-ahb-a800000.wifi.bin: firmware_loading_store: map pages failed
[ 11.773957] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/cal-ahb-a800000.wifi.bin failed with error -2
[ 11.781549] ath10k_ahb a800000.wifi: Falling back to user helper
[ 11.886712] firmware ath10k!cal-ahb-a800000.wifi.bin: firmware_loading_store: map pages failed
[ 11.887170] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 11.894351] ath10k_ahb a800000.wifi: Falling back to user helper
[ 11.965220] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 11.967068] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 11.973118] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 11.986549] ath10k_ahb a800000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67
[ 12.008282] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=Netgear-Orbi-Pr from ath10k/QCA4019/hw1.0/board-2.bin
[ 12.008434] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/board.bin failed with error -2
[ 12.025577] ath10k_ahb a800000.wifi: Falling back to user helper
[ 12.064344] firmware ath10k!QCA4019!hw1.0!board.bin: firmware_loading_store: map pages failed
[ 12.064552] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[ 12.071878] ath10k_ahb a800000.wifi: failed to fetch board file: -11
[ 12.081247] ath10k_ahb a800000.wifi: could not probe fw (-11)
[ 12.090475] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.588786] br-lan: port 1(eth0) entered blocking state
[ 16.588826] br-lan: port 1(eth0) entered disabled state
[ 16.593131] device eth0 entered promiscuous mode
[ 16.600481] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 16.614396] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 17.603491] br-lan: port 1(eth0) entered blocking state
[ 17.603528] br-lan: port 1(eth0) entered forwarding state
[ 17.607711] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment