Skip to content

Instantly share code, notes, and snippets.

@robimarko

robimarko/gist:6f8516392ff1922c00f958941fef236e

Created May 8, 2018 22:45
Show Gist options
  • Save robimarko/6f8516392ff1922c00f958941fef236e to your computer and use it in GitHub Desktop.
Save robimarko/6f8516392ff1922c00f958941fef236e to your computer and use it in GitHub Desktop.
Download ZIP
Orbi-openwrt-boot3
Raw
gistfile1.txt
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110
S - IMAGE_VARIANT_STRING=DAAAANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000023
S - Reset status Config, 0x00000000
S - Core 0 Frequency, 0 MHz
B - 262 - PBL, Start
B - 1343 - bootable_media_detect_entry, Start
B - 39982 - bootable_media_detect_success, Start
B - 39997 - elf_loader_entry, Start
B - 42192 - auth_hash_seg_entry, Start
B - 44363 - auth_hash_seg_exit, Start
B - 79520 - elf_segs_hash_verify_entry, Start
B - 194864 - PBL, End
B - 194889 - SBL1, Start
B - 287086 - pm_device_init, Start
D - 9 - pm_device_init, Delta
B - 288605 - boot_flash_init, Start
D - 37327 - boot_flash_init, Delta
B - 330238 - boot_config_data_table_init, Start
D - 2755 - boot_config_data_table_init, Delta - (419 Bytes)
B - 337941 - clock_init, Start
D - 7532 - clock_init, Delta
B - 349243 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B - 352649 - sbl1_ddr_set_params, Start
B - 357742 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 362124 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13170 - sbl1_ddr_set_params, Delta
B - 375420 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 446673 - sbl1_wait_for_ddr_training, Start
D - 27 - sbl1_wait_for_ddr_training, Delta
B - 463071 - Image Load, Start
D - 14746 - QSEE Image Loaded, Delta - (268920 Bytes)
B - 478244 - Image Load, Start
D - 899 - SEC Image Loaded, Delta - (0 Bytes)
B - 488099 - Image Load, Start
D - 12616 - APPSBL Image Loaded, Delta - (421607 Bytes)
B - 501141 - QSEE Execution, Start
D - 60 - QSEE Execution, Delta
B - 507335 - SBL1, End
D - 314558 - SBL1, Delta
S - Flash Throughput, 25412 KB/s (691298 Bytes, 27203 us)
S - DDR Frequency, 672 MHz
U-Boot 2012.07-g9274bc2-dirty [Barrier Breaker unknown,unknown] (Jun 16 2017 - 16:27:21)
U-boot dni1 V1.1 for DNI HW ID: 29765352; NOR flash 0MB; EMMC flash 4096MB; RAM 512MB
smem ram ptable found: ver: 1 len: 3
DRAM: 512 MiB
machid : 0x8010001
NAND: ID = 0
Vendor = 0
Device = 0
Nand Flash error. Status = 64
ONFI Read id cmd failed
ONFI probe failed
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
0 MiB
MMC: qca_mmc: 0
*** Warning - bad CRC, using default environment
PCI0 Link Intialized
In: serial
Out: serial
Err: serial
Valid chip addresses: 27 48
machid: 8010001
flash_type: 1
Net: MAC0 addr:b0:39:56:8d:59:69
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
Hit any key to stop autoboot: 0
(IPQ40xx) # print
baudrate=115200
bootcmd=mii write 0x0 0x0 0x0800; sleep 1; nmrp; bootdni; bootm 0x84000000
bootdelay=2
delenv=mmc erase 0x1822 0x200
ethact=eth0
flash_type=1
ipaddr=192.168.1.1
loadaddr=0x84000000
machid=8010001
serverip=192.168.1.10
stderr=serial
stdin=serial
stdout=serial
Environment size: 302/262140 bytes
(IPQ40xx) # setenv serverip 192.168.2.213
(IPQ40xx) # setenv ipaddr 192.168.2.233
(IPQ40xx) # tftpboot openwrt-ipq40xx-netgear_orbipro-initramfs-fit-uImage.itb
eth0 PHY0 up Speed :1000 Full duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
Using eth0 device
TFTP from server 192.168.2.213; our IP address is 192.168.2.233
Filename 'openwrt-ipq40xx-netgear_orbipro-initramfs-fit-uImage.itb'.
Load address: 0x84000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###############################################
done
Bytes transferred = 7354744 (703978 hex)
(IPQ40xx) # bootm
## Booting kernel from FIT Image at 84000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-4.14.37
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x840000e4
Data Size: 7318144 Bytes = 7 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: e7c1e32c
Hash algo: sha1
Hash value: e89b5aa9d06832f2d60b39ae2929bd3386f3036f
Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM OpenWrt netgear_orbipro device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x846faca0
Data Size: 34725 Bytes = 33.9 KiB
Architecture: ARM
Hash algo: crc32
Hash value: c3cc425b
Hash algo: sha1
Hash value: 05311c913cb6e4bafd3149bf377ad7c0b368ee4e
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x846faca0
Uncompressing Kernel Image ... OK
Loading Device Tree to 871e4000, end 871ef7a4 ... OK
Using machid 0x8010001 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.37 (robimarko@localhost.localdomain) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6868-004d90fc7c)) #0 SMP Tue May 8 22:35:20 2018
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Netgear Orbi Pro
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x3c0 with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu @dfba1000 s29260 r8192 d23988 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129536
[ 0.000000] Kernel command line:
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 500536K/522240K available (4325K kernel code, 141K rwdata, 1220K rodata, 10240K init, 246K bss, 21704K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc07394a0 (5318 kB)
[ 0.000000] .init : 0xc0900000 - 0xc1300000 (10240 kB)
[ 0.000000] .data : 0xc1300000 - 0xc1323400 ( 141 kB)
[ 0.000000] .bss : 0xc1325000 - 0xc1362874 ( 247 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
[ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
[ 0.000021] Switching to timer-based delay loop, resolution 20ns
[ 0.000427] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
[ 0.000445] pid_max: default: 32768 minimum: 301
[ 0.000580] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000595] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001179] CPU: Testing write buffer coherency: ok
[ 0.001791] Setting up static identity map for 0x80300000 - 0x80300060
[ 0.001915] Hierarchical SRCU implementation.
[ 0.002486] smp: Bringing up secondary CPUs ...
[ 0.004937] smp: Brought up 1 node, 4 CPUs
[ 0.004955] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.004963] CPU: All CPU(s) started in SVC mode.
[ 0.013650] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.013812] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.013834] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.014017] pinctrl core: initialized pinctrl subsystem
[ 0.014891] NET: Registered protocol family 16
[ 0.015140] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.016190] cpuidle: using governor ladder
[ 0.016229] cpuidle: using governor menu
[ 0.034096] msm_bus_fabric_init_driver
[ 0.034349] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.034365] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.034383] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1
[ 0.034422] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.034434] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.034449] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1
[ 0.090857] usbcore: registered new interface driver usbfs
[ 0.090922] usbcore: registered new interface driver hub
[ 0.091020] usbcore: registered new device driver usb
[ 0.091075] pps_core: LinuxPPS API ver. 1 registered
[ 0.091084] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.091108] PTP clock support registered
[ 0.092107] clocksource: Switched to clocksource arch_sys_counter
[ 0.092911] NET: Registered protocol family 2
[ 0.093502] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.093564] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.093654] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.093758] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.093791] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.093997] NET: Registered protocol family 1
[ 0.214817] No memory allocated for crashlog
[ 0.214966] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 0.218214] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.218230] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.223252] io scheduler noop registered
[ 0.223270] io scheduler deadline registered (default)
[ 0.224401] OF: PCI: host bridge /soc/pci@40000000 ranges:
[ 0.224439] OF: PCI: IO 0x40200000..0x402fffff -> 0x40200000
[ 0.224456] OF: PCI: MEM 0x40300000..0x406fffff -> 0x40300000
[ 0.442118] qcom-pcie 40000000.pci: link up
[ 0.442287] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00
[ 0.442307] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.442322] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x40200000-0x402fffff])
[ 0.442335] pci_bus 0000:00: root bus resource [mem 0x40300000-0x406fffff]
[ 0.442665] PCI: bus0: Fast back to back transfers disabled
[ 0.443782] PCI: bus1: Fast back to back transfers disabled
[ 0.443833] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff]
[ 0.443850] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit]
[ 0.443875] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit]
[ 0.443936] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.443952] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff]
[ 0.444711] pcieport 0000:00:00.0: AER enabled with IRQ 96
[ 0.446945] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[ 0.447026] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[ 0.447100] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[ 0.447176] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[ 0.447417] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.447964] msm_serial 78af000.serial: msm_serial: detected port #0
[ 0.448008] msm_serial 78af000.serial: uartclk = 1843200
[ 0.448057] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 26, base_baud = 115200) is a MSM
[ 0.448082] msm_serial: console setup on port #0
[ 1.091837] console [ttyMSM0] enabled
[ 1.096766] msm_serial: driver initialized
[ 1.104264] loop: module loaded
[ 1.105366] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 1.108072] ipq4019-pinctrl 1000000.pinctrl: pin_config_group_set op failed for group 6
[ 1.114450] ipq40xx-mdio 90000.mdio: Error applying setting, reverse things back
[ 1.122294] libphy: ipq40xx_mdio: probed
[ 1.198084] ESS reset ok!
[ 1.231076] ESS reset ok!
[ 1.662517] libphy: Fixed MDIO Bus: probed
[ 1.762829] i2c /dev entries driver
[ 1.763068] i2c_qup 78b7000.i2c: using default clock-frequency 100000
[ 1.767420] sdhci: Secure Digital Host Controller Interface driver
[ 1.771724] sdhci: Copyright(c) Pierre Ossman
[ 1.777881] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.782457] sdhci_msm 7824900.sdhci: Got SD LDO GPIO #33
[ 1.887991] sdhci_msm 7824900.sdhci: No vreg data found for vdd
[ 1.888021] sdhci_msm 7824900.sdhci: No vreg data found for vdd-io
[ 1.892743] sdhci_msm 7824900.sdhci: Parsing Pinctrl failed with -19, falling back on GPIO lib
[ 1.984927] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 2.005129] NET: Registered protocol family 10
[ 2.006511] Segment Routing with IPv6
[ 2.008539] NET: Registered protocol family 17
[ 2.012595] 8021q: 802.1Q VLAN Support v1.8
[ 2.016565] Registering SWP/SWPB emulation handler
�[ 2.108004] mmc0: Reset 0x1 never completed.
[ 2.108031] mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 2.111342] mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00004202
[ 2.117690] mmc0: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 2.124113] mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 2.130524] mmc0: sdhci: Present: 0x01f80000 | Host ctl: 0x00000000
[ 2.136966] mmc0: sdhci: Power: 0x00000000 | Blk gap: 0x00000000
[ 2.143382] mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x00000003
[ 2.149796] mmc0: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 2.156229] mmc0: sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
[ 2.162652] mmc0: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 2.169065] mmc0: sdhci: Caps: 0x302dc8b2 | Caps_1: 0x00008007
[ 2.175501] mmc0: sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
[ 2.181914] mmc0: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
[ 2.188348] mmc0: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 2.194771] mmc0: sdhci: Host ctl2: 0x00000000
[ 2.201182] mmc0: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x0000000000000000
[ 2.205535] mmc0: sdhci: ============================================
[ 2.226957] Freeing unused kernel memory: 10240K
[ 2.235721] init: Console is alive
[ 2.235931] init: - watchdog -
[ 2.247322] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.360639] mmc0: new HS200 MMC card at address 0001
[ 2.365471] mmcblk0: mmc0:0001 M62704 3.53 GiB
[ 2.367554] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB
[ 2.374937] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16
[ 2.672594] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.673258] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 2.679038] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x02010010
[ 2.685716] xhci-hcd xhci-hcd.0.auto: irq 131, io mem 0x08a00000
[ 2.694186] hub 1-0:1.0: USB hub found
[ 2.699640] hub 1-0:1.0: 1 port detected
[ 2.703588] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 2.707242] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 2.712738] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.720597] hub 2-0:1.0: USB hub found
[ 2.728461] hub 2-0:1.0: 1 port detected
[ 2.852609] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.853156] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 2.858923] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x02010010
[ 2.865854] xhci-hcd xhci-hcd.1.auto: irq 132, io mem 0x06000000
[ 2.874984] hub 3-0:1.0: USB hub found
[ 2.879645] hub 3-0:1.0: 1 port detected
[ 2.883577] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 2.887250] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 2.892684] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.900771] hub 4-0:1.0: USB hub found
[ 2.908496] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 2.913360] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.932336] init: - preinit -
[ 3.073684] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.105634] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.119535] random: jshn: uninitialized urandom read (4 bytes read)
/bin/board_detect: line 12: Unsupported: not found
[ 3.155213] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.170752] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.203905] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.225024] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.245225] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.270958] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.271046] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.438114] procd: - early -
[ 6.438248] procd: - watchdog -
[ 7.103197] procd: - watchdog -
[ 7.105921] procd: - ubus -
[ 7.125687] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.167960] random: ubusd: uninitialized urandom read (4 bytes read)
[ 7.173522] procd: - init -
Please press Enter to activate this console.
[ 7.300382] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.303140] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.695144] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 7.695177] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.703442] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.084301] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 8.286131] xt_time: kernel timezone is -0000
[ 8.558860] PPP generic driver version 2.4.2
[ 8.559771] NET: Registered protocol family 24
[ 8.572223] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 8.572726] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 8.744326] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[ 8.744639] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.787011] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 8.787403] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[ 8.794970] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.861454] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 8.861769] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2
[ 8.869065] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 8.923207] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 8.925236] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 8.931099] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 8.947055] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00053 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 4c56a386
[ 11.194669] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0046,subsystem-vendor=168c,subsystem-device=cafe from ath10k/QCA9984/hw1.0/board-2.bin
[ 11.194848] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/board.bin failed with error -2
[ 11.209906] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 11.254374] firmware ath10k!QCA9984!hw1.0!board.bin: firmware_loading_store: map pages failed
[ 11.254601] ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9984/hw1.0
[ 11.261910] ath10k_pci 0000:01:00.0: failed to fetch board file: -11
[ 11.271308] ath10k_pci 0000:01:00.0: could not probe fw (-11)
[ 11.450696] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a000000.wifi.bin failed with error -2
[ 11.451018] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.494176] firmware ath10k!pre-cal-ahb-a000000.wifi.bin: firmware_loading_store: map pages failed
[ 11.494635] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/cal-ahb-a000000.wifi.bin failed with error -2
[ 11.502065] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.558029] firmware ath10k!cal-ahb-a000000.wifi.bin: firmware_loading_store: map pages failed
[ 11.558336] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 11.565646] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.619320] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 11.621218] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 11.627314] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 11.640106] ath10k_ahb a000000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67
[ 11.663154] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA4019/hw1.0/board-2.bin
[ 11.663360] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/board.bin failed with error -2
[ 11.678388] ath10k_ahb a000000.wifi: Falling back to user helper
[ 11.717229] firmware ath10k!QCA4019!hw1.0!board.bin: firmware_loading_store: map pages failed
[ 11.717439] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[ 11.724814] ath10k_ahb a000000.wifi: failed to fetch board file: -11
[ 11.734102] ath10k_ahb a000000.wifi: could not probe fw (-11)
[ 11.922679] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a800000.wifi.bin failed with error -2
[ 11.923007] ath10k_ahb a800000.wifi: Falling back to user helper
[ 11.965797] firmware ath10k!pre-cal-ahb-a800000.wifi.bin: firmware_loading_store: map pages failed
[ 11.966177] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/cal-ahb-a800000.wifi.bin failed with error -2
[ 11.973746] ath10k_ahb a800000.wifi: Falling back to user helper
[ 12.035272] firmware ath10k!cal-ahb-a800000.wifi.bin: firmware_loading_store: map pages failed
[ 12.035733] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2
[ 12.042909] ath10k_ahb a800000.wifi: Falling back to user helper
[ 12.113432] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 12.115117] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[ 12.121330] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 12.134761] ath10k_ahb a800000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67
[ 12.157299] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA4019/hw1.0/board-2.bin
[ 12.157509] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/board.bin failed with error -2
[ 12.172557] ath10k_ahb a800000.wifi: Falling back to user helper
[ 12.225658] firmware ath10k!QCA4019!hw1.0!board.bin: firmware_loading_store: map pages failed
[ 12.225929] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[ 12.233266] ath10k_ahb a800000.wifi: failed to fetch board file: -11
[ 12.242601] ath10k_ahb a800000.wifi: could not probe fw (-11)
[ 12.252318] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 16.735414] br-lan: port 1(eth0) entered blocking state
[ 16.735457] br-lan: port 1(eth0) entered disabled state
[ 16.739766] device eth0 entered promiscuous mode
[ 16.746660] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 16.760350] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 17.763302] br-lan: port 1(eth0) entered blocking state
[ 17.763343] br-lan: port 1(eth0) entered forwarding state
[ 17.768389] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment