Created
May 8, 2018 22:16
-
-
Save robimarko/fdfdeab63cd34e79ca7d4bf8cae75343 to your computer and use it in GitHub Desktop.
Orbi-openwrt-boot2
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Format: Log Type - Time(microsec) - Message - Optional Info | |
| Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic | |
| S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 | |
| S - IMAGE_VARIANT_STRING=DAAAANAZA | |
| S - OEM_IMAGE_VERSION_STRING=CRM | |
| S - Boot Config, 0x00000023 | |
| S - Reset status Config, 0x00000000 | |
| S - Core 0 Frequency, 0 MHz | |
| B - 262 - PBL, Start | |
| B - 1343 - bootable_media_detect_entry, Start | |
| B - 39980 - bootable_media_detect_success, Start | |
| B - 39994 - elf_loader_entry, Start | |
| B - 42188 - auth_hash_seg_entry, Start | |
| B - 44361 - auth_hash_seg_exit, Start | |
| B - 79515 - elf_segs_hash_verify_entry, Start | |
| B - 195011 - PBL, End | |
| B - 195035 - SBL1, Start | |
| B - 287220 - pm_device_init, Start | |
| D - 9 - pm_device_init, Delta | |
| B - 288739 - boot_flash_init, Start | |
| D - 37237 - boot_flash_init, Delta | |
| B - 330287 - boot_config_data_table_init, Start | |
| D - 2659 - boot_config_data_table_init, Delta - (419 Bytes) | |
| B - 338005 - clock_init, Start | |
| D - 7548 - clock_init, Delta | |
| B - 349322 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 | |
| B - 352727 - sbl1_ddr_set_params, Start | |
| B - 357821 - cpr_init, Start | |
| D - 2 - cpr_init, Delta | |
| B - 362203 - Pre_DDR_clock_init, Start | |
| D - 4 - Pre_DDR_clock_init, Delta | |
| D - 13170 - sbl1_ddr_set_params, Delta | |
| B - 375499 - pm_driver_init, Start | |
| D - 2 - pm_driver_init, Delta | |
| B - 446687 - sbl1_wait_for_ddr_training, Start | |
| D - 27 - sbl1_wait_for_ddr_training, Delta | |
| B - 463083 - Image Load, Start | |
| D - 14664 - QSEE Image Loaded, Delta - (268920 Bytes) | |
| B - 478175 - Image Load, Start | |
| D - 899 - SEC Image Loaded, Delta - (0 Bytes) | |
| B - 488026 - Image Load, Start | |
| D - 12567 - APPSBL Image Loaded, Delta - (421607 Bytes) | |
| B - 501020 - QSEE Execution, Start | |
| D - 60 - QSEE Execution, Delta | |
| B - 507200 - SBL1, End | |
| D - 314277 - SBL1, Delta | |
| S - Flash Throughput, 25623 KB/s (691298 Bytes, 26979 us) | |
| S - DDR Frequency, 672 MHz | |
| U-Boot 2012.07-g9274bc2-dirty [Barrier Breaker unknown,unknown] (Jun 16 2017 - 16:27:21) | |
| U-boot dni1 V1.1 for DNI HW ID: 29765352; NOR flash 0MB; EMMC flash 4096MB; RAM 512MB | |
| smem ram ptable found: ver: 1 len: 3 | |
| DRAM: 512 MiB | |
| machid : 0x8010001 | |
| NAND: ID = 0 | |
| Vendor = 0 | |
| Device = 0 | |
| Nand Flash error. Status = 64 | |
| ONFI Read id cmd failed | |
| ONFI probe failed | |
| SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff | |
| ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) | |
| 0 MiB | |
| MMC: qca_mmc: 0 | |
| *** Warning - bad CRC, using default environment | |
| PCI0 Link Intialized | |
| In: serial | |
| Out: serial | |
| Err: serial | |
| Valid chip addresses: 27 48 | |
| machid: 8010001 | |
| flash_type: 1 | |
| Net: MAC0 addr:b0:39:56:8d:59:69 | |
| PHY ID1: 0x4d | |
| PHY ID2: 0xd0b1 | |
| ipq40xx_ess_sw_init done | |
| eth0 | |
| Hit any key to stop autoboot: 0 | |
| (IPQ40xx) # print | |
| baudrate=115200 | |
| bootcmd=mii write 0x0 0x0 0x0800; sleep 1; nmrp; bootdni; bootm 0x84000000 | |
| bootdelay=2 | |
| delenv=mmc erase 0x1822 0x200 | |
| ethact=eth0 | |
| flash_type=1 | |
| ipaddr=192.168.1.1 | |
| loadaddr=0x84000000 | |
| machid=8010001 | |
| serverip=192.168.1.10 | |
| stderr=serial | |
| stdin=serial | |
| stdout=serial | |
| Environment size: 302/262140 bytes | |
| (IPQ40xx) # setenv ipaddr 192.168.2.233 | |
| (IPQ40xx) # setenv serverip 192.168.2.213 | |
| (IPQ40xx) # tftpboot openwrt-ipq40xx-netgear_orbipro-initramfs-fit-uImage.itb | |
| eth0 PHY0 up Speed :1000 Full duplex | |
| eth0 PHY1 Down Speed :10 Half duplex | |
| eth0 PHY2 Down Speed :10 Half duplex | |
| eth0 PHY3 Down Speed :10 Half duplex | |
| eth0 PHY4 Down Speed :10 Half duplex | |
| Using eth0 device | |
| TFTP from server 192.168.2.213; our IP address is 192.168.2.233 | |
| Filename 'openwrt-ipq40xx-netgear_orbipro-initramfs-fit-uImage.itb'. | |
| Load address: 0x84000000 | |
| Loading: ################################################################# | |
| ################################################################# | |
| ################################################################# | |
| ################################################################# | |
| ################################################################# | |
| ################################################################# | |
| ################################################################# | |
| ############################################### | |
| done | |
| Bytes transferred = 7354688 (703940 hex) | |
| (IPQ40xx) # bootm | |
| ## Booting kernel from FIT Image at 84000000 ... | |
| Using 'config@1' configuration | |
| Trying 'kernel@1' kernel subimage | |
| Description: ARM OpenWrt Linux-4.14.37 | |
| Type: Kernel Image | |
| Compression: gzip compressed | |
| Data Start: 0x840000e4 | |
| Data Size: 7318122 Bytes = 7 MiB | |
| Architecture: ARM | |
| OS: Linux | |
| Load Address: 0x80208000 | |
| Entry Point: 0x80208000 | |
| Hash algo: crc32 | |
| Hash value: ee7e7717 | |
| Hash algo: sha1 | |
| Hash value: 046e480072e038b68d5c71810ee2a8c7b6072b4b | |
| Verifying Hash Integrity ... crc32+ sha1+ OK | |
| ## Flattened Device Tree from FIT Image at 84000000 | |
| Using 'config@1' configuration | |
| Trying 'fdt@1' FDT blob subimage | |
| Description: ARM OpenWrt netgear_orbipro device tree blob | |
| Type: Flat Device Tree | |
| Compression: uncompressed | |
| Data Start: 0x846fac8c | |
| Data Size: 34691 Bytes = 33.9 KiB | |
| Architecture: ARM | |
| Hash algo: crc32 | |
| Hash value: 296915fa | |
| Hash algo: sha1 | |
| Hash value: f8987cda6774ca5cb029eff85a985ce865ef2656 | |
| Verifying Hash Integrity ... crc32+ sha1+ OK | |
| Booting using the fdt blob at 0x846fac8c | |
| Uncompressing Kernel Image ... OK | |
| Loading Device Tree to 871e4000, end 871ef782 ... OK | |
| Using machid 0x8010001 from environment | |
| Starting kernel ... | |
| [ 0.000000] Booting Linux on physical CPU 0x0 | |
| [ 0.000000] Linux version 4.14.37 (robimarko@localhost.localdomain) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6868-004d90fc7c)) #0 SMP Tue May 8 22:07:06 2018 | |
| [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d | |
| [ 0.000000] CPU: div instructions available: patching division code | |
| [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache | |
| [ 0.000000] OF: fdt: Machine model: Netgear Orbi Pro | |
| [ 0.000000] Memory policy: Data cache writealloc | |
| [ 0.000000] random: get_random_bytes called from start_kernel+0x88/0x3c0 with crng_init=0 | |
| [ 0.000000] percpu: Embedded 15 pages/cpu @dfba1000 s29260 r8192 d23988 u61440 | |
| [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129536 | |
| [ 0.000000] Kernel command line: | |
| [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) | |
| [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) | |
| [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) | |
| [ 0.000000] Memory: 500536K/522240K available (4325K kernel code, 141K rwdata, 1220K rodata, 10240K init, 246K bss, 21704K reserved, 0K cma-reserved, 0K highmem) | |
| [ 0.000000] Virtual kernel memory layout: | |
| [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) | |
| [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) | |
| [ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) | |
| [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) | |
| [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) | |
| [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) | |
| [ 0.000000] .text : 0xc0208000 - 0xc07394a0 (5318 kB) | |
| [ 0.000000] .init : 0xc0900000 - 0xc1300000 (10240 kB) | |
| [ 0.000000] .data : 0xc1300000 - 0xc1323400 ( 141 kB) | |
| [ 0.000000] .bss : 0xc1325000 - 0xc1362874 ( 247 kB) | |
| [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 | |
| [ 0.000000] Hierarchical RCU implementation. | |
| [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 | |
| [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). | |
| [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns | |
| [ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns | |
| [ 0.000021] Switching to timer-based delay loop, resolution 20ns | |
| [ 0.000422] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) | |
| [ 0.000440] pid_max: default: 32768 minimum: 301 | |
| [ 0.000569] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
| [ 0.000586] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) | |
| [ 0.001173] CPU: Testing write buffer coherency: ok | |
| [ 0.001785] Setting up static identity map for 0x80300000 - 0x80300060 | |
| [ 0.001909] Hierarchical SRCU implementation. | |
| [ 0.002478] smp: Bringing up secondary CPUs ... | |
| [ 0.004951] smp: Brought up 1 node, 4 CPUs | |
| [ 0.004967] SMP: Total of 4 processors activated (384.00 BogoMIPS). | |
| [ 0.004976] CPU: All CPU(s) started in SVC mode. | |
| [ 0.013677] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 | |
| [ 0.013837] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns | |
| [ 0.013860] futex hash table entries: 1024 (order: 4, 65536 bytes) | |
| [ 0.014041] pinctrl core: initialized pinctrl subsystem | |
| [ 0.014912] NET: Registered protocol family 16 | |
| [ 0.015167] DMA: preallocated 256 KiB pool for atomic coherent allocations | |
| [ 0.016204] cpuidle: using governor ladder | |
| [ 0.016245] cpuidle: using governor menu | |
| [ 0.034081] msm_bus_fabric_init_driver | |
| [ 0.034338] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 | |
| [ 0.034353] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 | |
| [ 0.034370] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1 | |
| [ 0.034408] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 | |
| [ 0.034420] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 | |
| [ 0.034434] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1 | |
| [ 0.090923] usbcore: registered new interface driver usbfs | |
| [ 0.090985] usbcore: registered new interface driver hub | |
| [ 0.091080] usbcore: registered new device driver usb | |
| [ 0.091127] pps_core: LinuxPPS API ver. 1 registered | |
| [ 0.091136] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> | |
| [ 0.091168] PTP clock support registered | |
| [ 0.092175] clocksource: Switched to clocksource arch_sys_counter | |
| [ 0.092984] NET: Registered protocol family 2 | |
| [ 0.093569] TCP established hash table entries: 4096 (order: 2, 16384 bytes) | |
| [ 0.093633] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) | |
| [ 0.093721] TCP: Hash tables configured (established 4096 bind 4096) | |
| [ 0.093829] UDP hash table entries: 256 (order: 1, 8192 bytes) | |
| [ 0.093864] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) | |
| [ 0.094064] NET: Registered protocol family 1 | |
| [ 0.214832] No memory allocated for crashlog | |
| [ 0.214983] workingset: timestamp_bits=30 max_order=17 bucket_order=0 | |
| [ 0.218227] squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| [ 0.218243] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. | |
| [ 0.223720] io scheduler noop registered | |
| [ 0.223739] io scheduler deadline registered (default) | |
| [ 0.224879] OF: PCI: host bridge /soc/pci@40000000 ranges: | |
| [ 0.224912] OF: PCI: IO 0x40200000..0x402fffff -> 0x40200000 | |
| [ 0.224929] OF: PCI: MEM 0x40300000..0x406fffff -> 0x40300000 | |
| [ 0.442185] qcom-pcie 40000000.pci: link up | |
| [ 0.442348] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00 | |
| [ 0.442368] pci_bus 0000:00: root bus resource [bus 00-ff] | |
| [ 0.442383] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x40200000-0x402fffff]) | |
| [ 0.442396] pci_bus 0000:00: root bus resource [mem 0x40300000-0x406fffff] | |
| [ 0.442734] PCI: bus0: Fast back to back transfers disabled | |
| [ 0.443850] PCI: bus1: Fast back to back transfers disabled | |
| [ 0.443903] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] | |
| [ 0.443920] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit] | |
| [ 0.443944] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] | |
| [ 0.444008] pci 0000:00:00.0: PCI bridge to [bus 01-ff] | |
| [ 0.444023] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] | |
| [ 0.444774] pcieport 0000:00:00.0: AER enabled with IRQ 96 | |
| [ 0.447026] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 | |
| [ 0.447110] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 | |
| [ 0.447181] tcsr 1953000.ess_tcsr: setting ess interface select = 0 | |
| [ 0.447254] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 | |
| [ 0.447491] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled | |
| [ 0.448060] msm_serial 78af000.serial: msm_serial: detected port #0 | |
| [ 0.448105] msm_serial 78af000.serial: uartclk = 1843200 | |
| [ 0.448152] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 26, base_baud = 115200) is a MSM | |
| [ 0.448177] msm_serial: console setup on port #0 | |
| [ 1.091931] console [ttyMSM0] enabled | |
| [ 1.096864] msm_serial: driver initialized | |
| [ 1.104369] loop: module loaded | |
| [ 1.105452] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 | |
| [ 1.108180] ipq4019-pinctrl 1000000.pinctrl: pin_config_group_set op failed for group 6 | |
| [ 1.114536] ipq40xx-mdio 90000.mdio: Error applying setting, reverse things back | |
| [ 1.122390] libphy: ipq40xx_mdio: probed | |
| [ 1.198250] ESS reset ok! | |
| [ 1.231244] ESS reset ok! | |
| [ 1.662579] libphy: Fixed MDIO Bus: probed | |
| [ 1.762891] i2c /dev entries driver | |
| [ 1.763128] i2c_qup 78b7000.i2c: using default clock-frequency 100000 | |
| [ 1.767475] sdhci: Secure Digital Host Controller Interface driver | |
| [ 1.771786] sdhci: Copyright(c) Pierre Ossman | |
| [ 1.777940] sdhci-pltfm: SDHCI platform and OF driver helper | |
| [ 1.782475] sdhci_msm 7824900.sdhci: Failed to get slot index -19 | |
| [ 1.791589] NET: Registered protocol family 10 | |
| [ 1.795431] Segment Routing with IPv6 | |
| [ 1.798427] NET: Registered protocol family 17 | |
| [ 1.802509] 8021q: 802.1Q VLAN Support v1.8 | |
| [ 1.806448] Registering SWP/SWPB emulation handler | |
| [ 1.814717] hctosys: unable to open rtc device�[ 1.835097] Freeing unused kernel memory: 10240K | |
| [ 1.844036] init: Console is alive | |
| [ 1.844223] init: - watchdog - | |
| [ 1.854059] kmodloader: loading kernel modules from /etc/modules-boot.d/* | |
| [ 2.282677] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller | |
| [ 2.283292] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 | |
| [ 2.289152] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x02010010 | |
| [ 2.295836] xhci-hcd xhci-hcd.0.auto: irq 130, io mem 0x08a00000 | |
| [ 2.311014] hub 1-0:1.0: USB hub found | |
| [ 2.311781] hub 1-0:1.0: 1 port detected | |
| [ 2.314090] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller | |
| [ 2.317849] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 | |
| [ 2.323263] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. | |
| [ 2.331189] hub 2-0:1.0: USB hub found | |
| [ 2.339094] hub 2-0:1.0: 1 port detected | |
| [ 2.462739] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller | |
| [ 2.463291] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 | |
| [ 2.469044] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x02010010 | |
| [ 2.475863] xhci-hcd xhci-hcd.1.auto: irq 131, io mem 0x06000000 | |
| [ 2.485014] hub 3-0:1.0: USB hub found | |
| [ 2.489758] hub 3-0:1.0: 1 port detected | |
| [ 2.493602] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller | |
| [ 2.497372] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 | |
| [ 2.502777] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. | |
| [ 2.510729] hub 4-0:1.0: USB hub found | |
| [ 2.518601] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) | |
| [ 2.523448] kmodloader: done loading kernel modules from /etc/modules-boot.d/* | |
| [ 2.542522] init: - preinit - | |
| [ 2.677543] random: jshn: uninitialized urandom read (4 bytes read) | |
| [ 2.711995] random: jshn: uninitialized urandom read (4 bytes read) | |
| [ 2.723882] random: jshn: uninitialized urandom read (4 bytes read) | |
| /bin/board_detect: line 12: Unsupported: not found | |
| [ 2.756335] random: jshn: uninitialized urandom read (4 bytes read) | |
| [ 2.767745] random: jshn: uninitialized urandom read (4 bytes read) | |
| [ 2.795352] random: jshn: uninitialized urandom read (4 bytes read) | |
| [ 2.826474] random: jshn: uninitialized urandom read (4 bytes read) | |
| [ 2.843860] random: jshn: uninitialized urandom read (4 bytes read) | |
| [ 2.870457] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready | |
| [ 2.870545] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready | |
| Press the [f] key and hit [enter] to enter failsafe mode | |
| Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level | |
| [ 6.027871] procd: - early - | |
| [ 6.028005] procd: - watchdog - | |
| [ 6.663263] procd: - watchdog - | |
| [ 6.665991] procd: - ubus - | |
| [ 6.677652] random: ubusd: uninitialized urandom read (4 bytes read) | |
| [ 6.728423] random: ubusd: uninitialized urandom read (4 bytes read) | |
| [ 6.739943] procd: - init - | |
| Please press Enter to activate this console. | |
| [ 6.868223] kmodloader: loading kernel modules from /etc/modules.d/* | |
| [ 6.871755] ip6_tables: (C) 2000-2006 Netfilter Core Team | |
| [ 7.257184] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180 | |
| [ 7.257224] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d | |
| [ 7.265948] ip_tables: (C) 2000-2006 Netfilter Core Team | |
| [ 7.634282] nf_conntrack version 0.5.0 (8192 buckets, 32768 max) | |
| [ 7.874183] xt_time: kernel timezone is -0000 | |
| [ 8.110836] PPP generic driver version 2.4.2 | |
| [ 8.111991] NET: Registered protocol family 24 | |
| [ 8.124279] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) | |
| [ 8.124783] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 | |
| [ 8.294036] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2 | |
| [ 8.294083] ath10k_pci 0000:01:00.0: Falling back to user helper | |
| [ 8.341425] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed | |
| [ 8.341713] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2 | |
| [ 8.349332] ath10k_pci 0000:01:00.0: Falling back to user helper | |
| [ 8.419170] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed | |
| [ 8.419548] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/firmware-6.bin failed with error -2 | |
| [ 8.426776] ath10k_pci 0000:01:00.0: Falling back to user helper | |
| [ 8.488661] firmware ath10k!QCA9984!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed | |
| [ 8.491016] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe | |
| [ 8.496619] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 | |
| [ 8.510834] ath10k_pci 0000:01:00.0: firmware ver 10.4-3.5.3-00053 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 4c56a386 | |
| [ 10.758616] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0046,subsystem-vendor=168c,subsystem-device=cafe from ath10k/QCA9984/hw1.0/board-2.bin | |
| [ 10.758800] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9984/hw1.0/board.bin failed with error -2 | |
| [ 10.773847] ath10k_pci 0000:01:00.0: Falling back to user helper | |
| [ 10.812541] firmware ath10k!QCA9984!hw1.0!board.bin: firmware_loading_store: map pages failed | |
| [ 10.812738] ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9984/hw1.0 | |
| [ 10.820078] ath10k_pci 0000:01:00.0: failed to fetch board file: -11 | |
| [ 10.829518] ath10k_pci 0000:01:00.0: could not probe fw (-11) | |
| [ 11.011979] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a000000.wifi.bin failed with error -2 | |
| [ 11.012643] ath10k_ahb a000000.wifi: Falling back to user helper | |
| [ 11.054961] firmware ath10k!pre-cal-ahb-a000000.wifi.bin: firmware_loading_store: map pages failed | |
| [ 11.055332] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/cal-ahb-a000000.wifi.bin failed with error -2 | |
| [ 11.062892] ath10k_ahb a000000.wifi: Falling back to user helper | |
| [ 11.131840] firmware ath10k!cal-ahb-a000000.wifi.bin: firmware_loading_store: map pages failed | |
| [ 11.132296] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2 | |
| [ 11.139378] ath10k_ahb a000000.wifi: Falling back to user helper | |
| [ 11.200996] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed | |
| [ 11.202902] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 | |
| [ 11.208892] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 | |
| [ 11.223268] ath10k_ahb a000000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67 | |
| [ 11.244745] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA4019/hw1.0/board-2.bin | |
| [ 11.244956] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/board.bin failed with error -2 | |
| [ 11.259959] ath10k_ahb a000000.wifi: Falling back to user helper | |
| [ 11.304471] firmware ath10k!QCA4019!hw1.0!board.bin: firmware_loading_store: map pages failed | |
| [ 11.304689] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0 | |
| [ 11.312006] ath10k_ahb a000000.wifi: failed to fetch board file: -11 | |
| [ 11.321373] ath10k_ahb a000000.wifi: could not probe fw (-11) | |
| [ 11.504657] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a800000.wifi.bin failed with error -2 | |
| [ 11.504707] ath10k_ahb a800000.wifi: Falling back to user helper | |
| [ 11.544960] firmware ath10k!pre-cal-ahb-a800000.wifi.bin: firmware_loading_store: map pages failed | |
| [ 11.545419] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/cal-ahb-a800000.wifi.bin failed with error -2 | |
| [ 11.552891] ath10k_ahb a800000.wifi: Falling back to user helper | |
| [ 11.621443] firmware ath10k!cal-ahb-a800000.wifi.bin: firmware_loading_store: map pages failed | |
| [ 11.621816] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2 | |
| [ 11.629074] ath10k_ahb a800000.wifi: Falling back to user helper | |
| [ 11.690792] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed | |
| [ 11.692523] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 | |
| [ 11.698687] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 | |
| [ 11.713103] ath10k_ahb a800000.wifi: firmware ver 10.4-3.4-00104 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps crc32 6c332c67 | |
| [ 11.734531] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA4019/hw1.0/board-2.bin | |
| [ 11.734741] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/board.bin failed with error -2 | |
| [ 11.749743] ath10k_ahb a800000.wifi: Falling back to user helper | |
| [ 11.793887] firmware ath10k!QCA4019!hw1.0!board.bin: firmware_loading_store: map pages failed | |
| [ 11.794104] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0 | |
| [ 11.801425] ath10k_ahb a800000.wifi: failed to fetch board file: -11 | |
| [ 11.810796] ath10k_ahb a800000.wifi: could not probe fw (-11) | |
| [ 11.820168] kmodloader: done loading kernel modules from /etc/modules.d/* | |
| [ 16.282744] br-lan: port 1(eth0) entered blocking state | |
| [ 16.282785] br-lan: port 1(eth0) entered disabled state | |
| [ 16.287101] device eth0 entered promiscuous mode | |
| [ 16.293971] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready | |
| [ 16.307266] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready | |
| [ 17.282237] br-lan: port 1(eth0) entered blocking state | |
| [ 17.282279] br-lan: port 1(eth0) entered forwarding state | |
| [ 17.286466] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment