Skip to content

Instantly share code, notes, and snippets.

@ryo
Created July 28, 2014 19:32
Show Gist options
  • Save ryo/b3f10b909b9a5ca0cdb5 to your computer and use it in GitHub Desktop.
Save ryo/b3f10b909b9a5ca0cdb5 to your computer and use it in GitHub Desktop.
U-Boot 2009.08-00495-g10adc6d (Apr 24 2012 - 13:27:04)
CPU: Freescale i.MX 6 family 0.0V at 792 MHz
Temperature: can't get valid data!
mx6q pll1: 792MHz
mx6q pll2: 528MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 264000000Hz
emi_slow clock: 29333333Hz
ddr clock : 528000000Hz
usdhc1 clock : 200000000Hz
usdhc2 clock : 200000000Hz
usdhc3 clock : 200000000Hz
usdhc4 clock : 200000000Hz
nfc clock : 24000000Hz
Board: MX6Q-SABRELITE:[ POR]
Boot Device: I2C
I2C: ready
DRAM: 1 GB
MMC: FSL_USDHC: 0,FSL_USDHC: 1
JEDEC ID: 0xbf:0x25:0x41
Reading SPI NOR flash 0xc0000 [0x2000 bytes] -> ram 0x276009b8
SUCCESS
In: serial
Out: serial
Err: serial
Checking for recovery command file...
** Bad partition 6 **
Card did not respond to voltage select!
** Bad partition 6 **
MMC Device 2 not found
MMC Device 2 not found
** Block device MMC 2 not supported
Net: got MAC address from IIM: 00:19:b8:00:f2:f8
FEC0 [PRIME]
Hit any key to stop autoboot: 0
Found phy at 6
FEC: Link is Up 796d
Using FEC0 device
TFTP from server 172.31.185.12; our IP address is 172.31.185.22
Filename 'n'.
Load address: 0x10800000
Loading: #################################################################
#################################################################
###################################
done
Bytes transferred = 2407872 (24bdc0 hex)
## Starting application at 0x10800000 ...
PC=0x1080001c
SP=0x275ffe50
CPSR=0x600001d3
cortex_init <@ABC12-> ok
mmu_init_table <> ok
arm_cpuinit <FG01H1IJKLM> ok
start()
uboot arg = 0x1, 0x2760330c, 0x2760330c, 0x10800000
NetBSD/evbarm (nitrogen) booting ...
initarm: Configuring system, CLIDR=1110000003 CTR=0x83338003
arm32_bootmem_init: memstart=0x10800000, memsize=0x3f800000, kernelstart=0x10800000
arm32_bootmem_init: kernelend=0x10a64000
arm32_bootmem_init: adding 129742 free pages: [0x10a64000..0x4fffffff] (VA 0x80a64000)
arm32_kernel_vm_init: 0 L2 pages are needed to map 0x296000 kernel bytes
arm32_kernel_vm_init: allocating page tables for kernel vmadd_pages: adding pv 0x80a4c4e4 (pa 0x10a64000, va 0x80a64000, 2 pages) at tail
add_pages: appending pv 0x80a4c694 (0x10a68000..0x10a69fff) to 0x10a64000..0x10a67fff
add_pages: appending pv 0x80a4c6a8 (0x10a6a000..0x10a6bfff) to 0x10a64000..0x10a69fff
add_pages: appending pv 0x80a4c6bc (0x10a6c000..0x10a6dfff) to 0x10a64000..0x10a6bfff
add_pages: appending pv 0x80a4c6d0 (0x10a6e000..0x10a6ffff) to 0x10a64000..0x10a6dfff
add_pages: appending pv 0x80a4c6e4 (0x10a70000..0x10a71fff) to 0x10a64000..0x10a6ffff
add_pages: appending pv 0x80a4c6f8 (0x10a72000..0x10a73fff) to 0x10a64000..0x10a71fff
add_pages: appending pv 0x80a4c70c (0x10a74000..0x10a75fff) to 0x10a64000..0x10a73fff
add_pages: appending pv 0x80a4c720 (0x10a76000..0x10a77fff) to 0x10a64000..0x10a75fff
arm32_kernel_vm_init: allocating stacks
add_pages: appending pv 0x80a4c9d8 (0x10a78000..0x10a79fff) to 0x10a64000..0x10a77fff
add_pages: appending pv 0x80a4c9c4 (0x10a7a000..0x10a7bfff) to 0x10a64000..0x10a79fff
add_pages: appending pv 0x80a4c9b0 (0x10a7c000..0x10a7dfff) to 0x10a64000..0x10a7bfff
add_pages: appending pv 0x80a4c99c (0x10a7e000..0x10a7ffff) to 0x10a64000..0x10a7dfff
add_pages: appending pv 0x80a4c988 (0x10a80000..0x10a81fff) to 0x10a64000..0x10a7ffff
add_pages: appending pv 0x80a4c9ec (0x10a82000..0x10a83fff) to 0x10a64000..0x10a81fff
add_pages: appending pv 0x80a4c520 (0x10a84000..0x10a87fff) to 0x10a64000..0x10a83fff
Creating L1 page table at 0x10a64000
arm32_kernel_vm_init: adding L2 pt (VA 0x80a68000, PA 0x10a68000) for VA 0xc0800000 (vm)
arm32_kernel_vm_init: adding L2 pt (VA 0x80a6a000, PA 0x10a6a000) for VA 0xc1000000 (vm)
arm32_kernel_vm_init: adding L2 pt (VA 0x80a6c000, PA 0x10a6c000) for VA 0xc1800000 (vm)
arm32_kernel_vm_init: adding L2 pt (VA 0x80a6e000, PA 0x10a6e000) for VA 0xc2000000 (vm)
arm32_kernel_vm_init: adding L2 pt (VA 0x80a70000, PA 0x10a70000) for VA 0xc2800000 (vm)
arm32_kernel_vm_init: adding L2 pt (VA 0x80a72000, PA 0x10a72000) for VA 0xc3000000 (vm)
arm32_kernel_vm_init: adding L2 pt (VA 0x80a74000, PA 0x10a74000) for VA 0xc3800000 (vm)
arm32_kernel_vm_init: adding L2 pt (VA 0x80a76000, PA 0x10a76000) for VA 0xc4000000 (vm)
Mapping kernel
arm32_kernel_vm_init: adding chunk for kernel text 0x10800000..0x10a3bfff (VA 0x80800000)
add_pages: adding pv 0x80a4c4d0 (pa 0x10800000, va 0x80800000, 286 pages) before pa 0x10a64000
arm32_kernel_vm_init: adding chunk for kernel data/bss 0x10a3c000..0x10a63fff (VA 0x80a3c000)
add_pages: appending pv 0x80a4c548 (0x10a3c000..0x10a63fff) to 0x10800000..0x10a3bfff
add_pages: merging pv 0x80a4c4e4 (0x10a64000..0x10a87fff) to 0x10800000..0x10a63fff
Listing Chunks
arm32_kernel_vm_init: pv 0x80a4c4d0: chunk VA 0x80800000..0x80a87fff (PA 0x10800000, prot 3, cache 1)
Mapping Chunks
arm32_kernel_vm_init: mapping last chunk VA 0x80800000..0xbfffffff (PA 0x10800000, prot 3, cache 1)
pmap_map_chunk: pa=0x10800000 va=0x80800000 size=0x3f800000 resid=0x3f800000 prot=0x3 cache=1
SSSSSSSSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsSsS
devmap: 02000000 -> 021fffff @ ff000000
pmap_map_chunk: pa=0x2000000 va=0xff000000 size=0x200000 resid=0x200000 prot=0x3 cache=0
SS
devmap: 00a00000 -> 00afffff @ ff200000
pmap_map_chunk: pa=0xa00000 va=0xff200000 size=0x100000 resid=0x100000 prot=0x3 cache=0
S
Physical Virtual Num
Starting Ending Starting Ending Pages
SDRAM: 0x10800000 0x4fffffff 0x80800000 0xbfffffff 130048
text section: 0x10800000 0x10a3bfff 0x80800000 0x80a3bfff 286
data section: 0x10a40000 0x10a4bdc0 0x80a40000 0x80a4bdc0 6
bss section: 0x10a4bdc0 0x10a63f8c 0x80a4bdc0 0x80a63f8c 13
L1 page directory: 0x10a64000 0x10a67fff 0x80a64000 0x80a67fff 2
ABT stack (CPU 0): 0x10a78000 0x10a79fff 0x80a78000 0x80a79fff 1
FIQ stack (CPU 0): 0x10a7a000 0x10a7bfff 0x80a7a000 0x80a7bfff 1
IRQ stack (CPU 0): 0x10a7c000 0x10a7dfff 0x80a7c000 0x80a7dfff 1
UND stack (CPU 0): 0x10a7e000 0x10a7ffff 0x80a7e000 0x80a7ffff 1
IDLE stack (CPU 0): 0x10a80000 0x10a81fff 0x80a80000 0x80a81fff 1
SVC stack: 0x10a82000 0x10a83fff 0x80a82000 0x80a83fff 1
Message Buffer: 0x10a84000 0x10a87fff 0x80a84000 0x80a87fff 2
Free Memory: 0x10a88000 0x4fffffff 129724
TTBR0=0x4fffc05b TTBR1=0x4fffc05b TTBCR=0x1 CONTEXTIDR=0
switching to new L1 page table @0x10a64000... ttb (TTBCR=0x11 TTBR0=0x10a6405b TTBR1=0x10a6405b) OK
nfreeblocks = 1, free_pages = 129724 (0x1fabc)
bootstrap done.
vectors vbar=0x809a5b80 0x809a5b80
init subsystems: stacks vectors undefined page pmap_physload pmap kpm tlb0 locks l1pt cache(l1pt) specials pools [ Kernel symbol table missing! ]
done.
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.99.49 (NITROGEN6X) #381: Tue Jul 29 04:27:05 JST 2014
ryo@phenomena:/src/cvs/NetBSD/sys/arch/evbarm/compile/NITROGEN6X
total memory = 1016 MB
avail memory = 1003 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: 1 GHz Cortex-A9 r3p10 (Cortex V7A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/32B 4-way L1 VIPT Instruction cache
cpu0: 32KB/32B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 1024KB/32B 16-way write-back-locking-D L2 PIPT Unified cache
vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
armperiph0 at mainbus0
arml2cc0 at armperiph0: ARM PL310 r3p1a L2 Cache Controller (disabled)
arml2cc0: cache enabled
armgic0 at armperiph0: Generic Interrupt Controller, 160 sources (149 valid)
armgic0: 32 Priorities, 128 SPIs, 5 PPIs, 16 SGIs
a9tmr0 at armperiph0: A9 Global 64-bit Timer (792 MHz)
a9tmr0: interrupting on irq 27
a9wdt0 at armperiph0: A9 Watchdog Timer, default period is 12 seconds
axi0 at mainbus0: Advanced eXtensible Interface
imxuart0 at axi0 addr 0x2020000 intr 58
imxuart1 at axi0 addr 0x21e8000 intr 59
imxuart1: console
imxuart2 at axi0 addr 0x21ec000 intr 60
imxuart3 at axi0 addr 0x21f0000 intr 61
imxuart4 at axi0 addr 0x21f4000 intr 62
enet0 at axi0 addr 0x2188000 intr 150: Gigabit Ethernet Controller
enet0: Ethernet address 00:19:b8:00:f2:f8
micphy0 at enet0 phy 6: Micrel KSZ9021RNI 10/100/1000 PHY, rev. 1
micphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
boot device: <unknown>
root on enet0
nfs_boot: trying static
nfs_boot: client_addr=172.31.185.23
nfs_boot: gateway=172.31.185.65
nfs_boot: netmask=255.255.255.0
nfs_boot: server=172.31.185.12
nfs_boot: root=172.31.185.12:/src/boot/nitro
enet0: link state DOWN (was UNKNOWN)
root on 172.31.185.12:/src/boot/nitro
root time: 0x506fee3b
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
init: copying out path `/sbin/init' 11
Sat Oct 6 08:39:23 UTC 2012
Not checking /: fs_passno = 0 in /etc/fstab
Kernel RNG "sysctl" runs test FAILURE: too few runs of 2 0s (1114 < 1114)
cprng sysctl: failed statistical RNG test
Starting file system checks:
Setting tty flags.
WARNING: module error: vfs load failed for `wsdisplay', error 78
WARNING: module error: vfs load failed for `wsdisplay', error 78
WARNING: module error: vfs load failed for `wsdisplay', error 78
WARNING: module error: vfs load failed for `wsdisplay', error 78
WARNING: module error: vfs load failed for `com', error 78
WARNING: module error: vfs load failed for `com', error 78
Setting sysctl variables:
ddb.onpanic: 1 -> 0
Starting network.
/etc/rc: WARNING: $hostname not set.
Configuring network interfaces:.
Adding interface aliases:.
Building databases: dev, utmp, utmpx.
Starting syslogd.
Mounting all filesystems...
Clearing temporary files.
Updating fontconfig cache: done.
Creating a.out runtime link editor directory cache.
Checking quotas: done.
Setting securelevel: kern.securelevel: 0 -> 1
swapctl: WARNING: /var/swapfile is readable by the world
swapctl: adding /var/swapfile as swap device at priority 0
Starting virecover.
Checking for core dump...
savecore: no core dump (no dumpdev)
Starting local daemons:.
Updating motd.
postfix: rebuilding /etc/mail/aliases (missing /etc/mail/aliases.db)
newaliases: warning: inet_protocols: IPv6 support is disabled: Address family not supported by protocol family
newaliases: warning: inet_protocols: configuring for IPv4 support only
newaliases: warning: valid_hostname: empty hostname
newaliases: fatal: unable to use my own hostname
Oct 6 08:39:27 postfix/sendmail[285]: fatal: unable to use my own hostname
/etc/rc.d/postfix exited with code 1
Starting inetd.
Starting cron.
The following components reported failures:
/etc/rc.d/postfix
See /var/run/rc.log for more information.
Sat Oct 6 08:39:28 UTC 2012
NetBSD/evbarm (Amnesiac) (console)
login: root
Oct 6 08:39:30 login: ROOT LOGIN (root) on tty console
Last login: Sat Oct 6 08:40:13 2012 on console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.99.49 (NITROGEN6X) #381: Tue Jul 29 04:27:05 JST 2014
Welcome to NetBSD!
Terminal type is vt100.
We recommend that you create a non-root account and use su(1) for root access.
# uname -a
NetBSD 6.99.49 NetBSD 6.99.49 (NITROGEN6X) #381: Tue Jul 29 04:27:05 JST 2014 ryo@phenomena:/src/cvs/NetBSD/sys/arch/evbarm/compile/NITROGEN6X evbarm
#
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment