duovero 4.1.15 jethro boot log

duovero-4.1.15-jethro-boot-log.txt

U-Boot SPL 2015.07-jumpnow (Dec 22 2015 - 17:03:39)
OMAP4430 ES2.3
reading u-boot.img
reading u-boot.img


U-Boot 2015.07-jumpnow (Dec 22 2015 - 17:03:39 -0500)

CPU  : OMAP4430 ES2.3
Board: duovero
I2C:   ready
DRAM:  1 GiB
MMC:   OMAP SD/MMC: 0
Using default environment

Net:   smc911x-0
Warning: smc911x-0 using MAC address from net device

Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
963 bytes read in 23 ms (40 KiB/s)
Importing environment from mmc0 ...
Running uenvcmd ...
55591 bytes read in 27 ms (2 MiB/s)
Loaded jumpnow-duovero-parlor.dtb
4534968 bytes read in 246 ms (17.6 MiB/s)
Kernel image @ 0x82000000 [ 0x000000 - 0x4532b8 ]
## Flattened Device Tree blob at 88000000
   Booting using the fdt blob at 0x88000000
   Loading Device Tree to 8ffef000, end 8ffff926 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.1.15-jumpnow (scott@octo) (gcc version 5.2.0 (GCC) ) #1 SMP Tue Dec 22 17:01:15 EST 2015
[    0.000000] CPU: ARMv7 Processor [411fc093] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: OMAP4430 Gumstix Duovero on Parlor
[    0.000000] cma: Reserved 16 MiB at 0xbe800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] OMAP4430 ES2.3
[    0.000000] PERCPU: Embedded 13 pages/cpu @eef97000 s22528 r8192 d22528 u53248
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260368
[    0.000000] Kernel command line: console=ttyO2,115200n8 consoleblank=0 root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1004264K/1047552K available (6006K kernel code, 643K rwdata, 2180K rodata, 404K init, 8201K bss, 26904K reserved, 16384K cma-reserved, 252928K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0806c30   (8188 kB)
[    0.000000]       .init : 0xc0807000 - 0xc086c000   ( 404 kB)
[    0.000000]       .data : 0xc086c000 - 0xc090cee8   ( 644 kB)
[    0.000000]        .bss : 0xc090cee8 - 0xc110f69c   (8202 kB)
[    0.000000] Running RCU self tests
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU lockdep checking is enabled.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] L2C: platform modifies aux control register: 0x0e070000 -> 0x3e470000
[    0.000000] L2C: DT/platform modifies aux control register: 0x0e070000 -> 0x3e470000
[    0.000000] L2C-310 erratum 727915 enabled
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[    0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB
[    0.000000] L2C-310: CACHE_ID 0x410000c4, AUX_CTRL 0x7e470000
[    0.000000] ti_dt_clocks_register: failed to lookup clock node dss_fck
[    0.000000] ti_dt_clocks_register: failed to lookup clock node dss_fck
[    0.000000] ti_dt_clocks_register: failed to lookup clock node div_ts_ck
[    0.000000] ti_dt_clocks_register: failed to lookup clock node bandgap_ts_fclk
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] clocksource 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65535999984741ns
[    0.000030] OMAP clocksource: 32k_counter at 32768 Hz
[    0.002227] Console: colour dummy device 80x30
[    0.002319] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.002319] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.002319] ... MAX_LOCK_DEPTH:          48
[    0.002349] ... MAX_LOCKDEP_KEYS:        8191
[    0.002349] ... CLASSHASH_SIZE:          4096
[    0.002349] ... MAX_LOCKDEP_ENTRIES:     32768
[    0.002349] ... MAX_LOCKDEP_CHAINS:      65536
[    0.002380] ... CHAINHASH_SIZE:          32768
[    0.002380]  memory used by lock dependency info: 5167 kB
[    0.002380]  per task-struct memory footprint: 1152 bytes
[    0.002410] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    0.070373] pid_max: default: 32768 minimum: 301
[    0.070892] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.070922] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.074127] CPU: Testing write buffer coherency: ok
[    0.075683] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.075805] Setting up static identity map for 0x80008280 - 0x800082f0
[    0.120361] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.121307] Brought up 2 CPUs
[    0.121337] SMP: Total of 2 processors activated (2393.70 BogoMIPS).
[    0.121337] CPU: All CPU(s) started in SVC mode.
[    0.125183] devtmpfs: initialized
[    0.187561] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.193572] omap_hwmod: l3_main_3 using broken dt data from ocp
[    0.199005] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.404510] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.407379] pinctrl core: initialized pinctrl subsystem
[    0.414154] NET: Registered protocol family 16
[    0.420562] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.450622] cpuidle: using governor ladder
[    0.480407] cpuidle: using governor menu
[    0.498352] OMAP GPIO hardware version 0.1
[    0.511108] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.541076] platform 4b501000.aes: Cannot lookup hwmod 'aes'
[    0.541717] platform 480a5000.des: Cannot lookup hwmod 'des'
[    0.550415] No ATAGs?
[    0.550537] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.550537] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.553863] OMAP DMA hardware revision 0.0
[    0.556060] ARM PMU: not yet supported on OMAP4430 due to missing CTI driver
[    0.649963] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver
[    0.651428] reg-fixed-voltage w2cbw0015_vmmc: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_w2cbw0015_pins, deferring probe
[    0.658935] SCSI subsystem initialized
[    0.659820] usbcore: registered new interface driver usbfs
[    0.660034] usbcore: registered new interface driver hub
[    0.660247] usbcore: registered new device driver usb
[    0.660888] usb_phy_generic hsusb1_phy: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_hsusb1phy_pins, deferring probe
[    0.663940] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_i2c1_pins, deferring probe
[    0.664062] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_i2c2_pins, deferring probe
[    0.664184] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_i2c3_pins, deferring probe
[    0.664276] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@100000/pinmux@40/pinmux_i2c4_pins, deferring probe
[    0.670776] Switched to clocksource 32k_counter
[    0.825012] NET: Registered protocol family 2
[    0.827514] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.827819] TCP bind hash table entries: 8192 (order: 6, 294912 bytes)
[    0.830780] TCP: Hash tables configured (established 8192 bind 8192)
[    0.831146] UDP hash table entries: 512 (order: 3, 40960 bytes)
[    0.831542] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes)
[    0.833038] NET: Registered protocol family 1
[    0.844696] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.850433] VFS: Disk quotas dquot_6.6.0
[    0.851043] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.854888] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.861206] bounce: pool size: 64 pages
[    0.861389] io scheduler noop registered
[    0.861419] io scheduler deadline registered
[    0.861480] io scheduler cfq registered (default)
[    0.869049] pinctrl-single 4a100040.pinmux: 203 pins at pa fc100040 size 406
[    0.869659] pinctrl-single 4a31e040.pinmux: 28 pins at pa fc31e040 size 56
[    0.872497] 58000000.dss supply vdda_video not found, using dummy regulator
[    0.873107] OMAP DSS rev 4.0
[    0.884826] omapfb omapfb: failed to connect default display
[    0.884857] omapfb omapfb: failed to init overlay connections
[    0.889953] omapfb omapfb: failed to setup omapfb
[    0.890624] pbias-regulator: probe of 4a1005a0.omap4_padconf_global:pbias_regulator failed with error -22
[    0.894012] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.901397] omap_uart 4806a000.serial: no wakeirq for uart0
[    0.902130] 4806a000.serial: ttyO0 at MMIO 0x4806a000 (irq = 226, base_baud = 3000000) is a OMAP UART0
[    0.904327] omap_uart 4806c000.serial: no wakeirq for uart1
[    0.904663] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 227, base_baud = 3000000) is a OMAP UART1
[    0.905914] omap_uart 48020000.serial: no wakeirq for uart2
[    0.906219] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 228, base_baud = 3000000) is a OMAP UART2
[    1.733947] console [ttyO2] enabled
[    1.739196] omap_uart 4806e000.serial: no wakeirq for uart3
[    1.745483] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 229, base_baud = 3000000) is a OMAP UART3
[    1.788879] brd: module loaded
[    1.811614] loop: module loaded
[    1.818115] mtdoops: mtd device (mtddev=name/number) must be supplied
[    1.848937] libphy: smsc911x-mdio: probed
[    1.853576] smsc911x 2c000000.ethernet eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=2c000000.etherne:01, irq=-1)
[    1.865753] smsc911x 2c000000.ethernet eth0: MAC Address: 00:15:c9:28:f5:f3
[    1.874786] usbcore: registered new interface driver asix
[    1.880676] usbcore: registered new interface driver ax88179_178a
[    1.887176] usbcore: registered new interface driver cdc_ether
[    1.893524] usbcore: registered new interface driver smsc95xx
[    1.899719] usbcore: registered new interface driver net1080
[    1.905792] usbcore: registered new interface driver cdc_subset
[    1.912170] usbcore: registered new interface driver zaurus
[    1.918243] usbcore: registered new interface driver cdc_ncm
[    1.925201] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.932067] ehci-omap: OMAP-EHCI Host Controller driver
[    1.938232] ehci-omap 4a064c00.ehci: Can't get PHY device for port 0: -517
[    1.945861] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.952392] ohci-omap3: OHCI OMAP3 driver
[    1.957275] ohci-omap3 4a064800.ohci: OHCI Host Controller
[    1.963897] ohci-omap3 4a064800.ohci: new USB bus registered, assigned bus number 1
[    1.972778] ohci-omap3 4a064800.ohci: irq 331, io mem 0x4a064800
[    2.053497] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    2.060638] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.068145] usb usb1: Product: OHCI Host Controller
[    2.073272] usb usb1: Manufacturer: Linux 4.1.15-jumpnow ohci_hcd
[    2.079620] usb usb1: SerialNumber: 4a064800.ohci
[    2.089630] hub 1-0:1.0: USB hub found
[    2.094085] hub 1-0:1.0: 3 ports detected
[    2.103088] usbcore: registered new interface driver cdc_wdm
[    2.109283] usbcore: registered new interface driver usb-storage
[    2.115814] usbcore: registered new interface driver usbtest
[    2.123260] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver
[    2.129302] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 2
[    2.138275] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    2.145416] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.152984] usb usb2: Product: MUSB HDRC host driver
[    2.158142] usb usb2: Manufacturer: Linux 4.1.15-jumpnow musb-hcd
[    2.164550] usb usb2: SerialNumber: musb-hdrc.0.auto
[    2.171905] hub 2-0:1.0: USB hub found
[    2.176147] hub 2-0:1.0: 1 port detected
[    2.245300] mousedev: PS/2 mouse device common for all mice
[    2.255157] i2c /dev entries driver
[    2.264129] omap_wdt: OMAP Watchdog Timer Rev 0x00: initial timeout 60 sec
[    2.275878] omap_hsmmc 4809c000.mmc: unable to get vmmc regulator -517
[    2.284332] omap_hsmmc 480d5000.mmc: unable to get vmmc regulator -517
[    2.294219] ledtrig-cpu: registered to indicate activity on CPUs
[    2.301391] usbcore: registered new interface driver usbhid
[    2.307220] usbhid: USB HID core driver
[    2.313415] oprofile: no performance counters
[    2.319519] oprofile: using timer interrupt.
[    2.325042] Initializing XFRM netlink socket
[    2.329711] NET: Registered protocol family 17
[    2.334716] NET: Registered protocol family 15
[    2.340148] Key type dns_resolver registered
[    2.345001] twl: not initialized
[    2.348358] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660
[    2.356750] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660
[    2.365142] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660
[    2.373535] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660
[    2.381927] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660
[    2.390258] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1375000 Vs max 1316660
[    2.398651] twl6030_uv_to_vsel:OUT OF RANGE! non mapped vsel for 1410000 Vs max 1316660
[    2.407043] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu
[    2.414245] omap2_set_init_voltage: unable to set vdd_mpu
[    2.419891] omap2_set_init_voltage: unable to find boot up OPP for vdd_core
[    2.427185] omap2_set_init_voltage: unable to set vdd_core
[    2.432952] omap2_set_init_voltage: unable to find boot up OPP for vdd_iva
[    2.440124] omap2_set_init_voltage: unable to set vdd_iva
[    2.448760] Power Management for TI OMAP4+ devices.
[    2.453887] OMAP4 PM: u-boot >= v2012.07 is required for full PM support
[    2.461303] ThumbEE CPU extension supported.
[    2.461303] Registering SWP/SWPB emulation handler
[    2.472290] SmartReflex Class3 initialized
[    2.500762] hw-breakpoint: Failed to enable monitor mode on CPU 0.
[    2.510742] hw-breakpoint: CPU 0 failed to disable vector catch
[    2.562438] hsusb1_phy supply vcc not found, using dummy regulator
[    2.575683] Skipping twl internal clock init and using bootloader value (unknown osc rate)
[    2.603820] twl 0-0048: PIH (irq 333) nested IRQs
[    2.612762] twl_rtc 48070000.i2c:twl@48:rtc: Power up reset detected.
[    2.621490] twl_rtc 48070000.i2c:twl@48:rtc: Enabling TWL-RTC
[    2.634460] twl_rtc 48070000.i2c:twl@48:rtc: rtc core: registered 48070000.i2c:twl@48 as rtc0
[    2.678039] twl6030_usb 48070000.i2c:twl@48:usb-comparator: Initialized TWL6030 USB module
[    2.690155] twl6040 0-004b: clk32k is not handled
[    2.714996] omap_i2c 48070000.i2c: bus 0 rev0.10 at 400 kHz
[    2.724548] omap_i2c 48072000.i2c: bus 1 rev0.10 at 400 kHz
[    2.733276] omap_i2c 48060000.i2c: bus 2 rev0.10 at 100 kHz
[    2.741638] omap_i2c 48350000.i2c: bus 3 rev0.10 at 400 kHz
[    2.760681] omapdss HDMICORE error: timeout reading edid
[    2.790679] Console: switching to colour frame buffer device 80x30
[    2.811309] omapfb omapfb: using display 'hdmi' mode 640x480
[    2.831390] ehci-omap 4a064c00.ehci: EHCI Host Controller
[    2.837402] ehci-omap 4a064c00.ehci: new USB bus registered, assigned bus number 3
[    2.845977] ehci-omap 4a064c00.ehci: irq 332, io mem 0x4a064c00
[    2.870666] ehci-omap 4a064c00.ehci: USB 2.0 started, EHCI 1.00
[    2.878295] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    2.885467] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.893035] usb usb3: Product: EHCI Host Controller
[    2.898162] usb usb3: Manufacturer: Linux 4.1.15-jumpnow ehci_hcd
[    2.904541] usb usb3: SerialNumber: 4a064c00.ehci
[    2.913909] hub 3-0:1.0: USB hub found
[    2.918518] hub 3-0:1.0: 3 ports detected
[    3.025451] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[    3.037841] twl_rtc 48070000.i2c:twl@48:rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[    3.047790] sr_init: No PMIC hook to init smartreflex
[    3.053405] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
[    3.062438] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
[    3.071228] smartreflex smartreflex.2: omap_sr_probe: SmartReflex driver initialized
[    3.089202] mmc0: host does not support reading read-only switch, assuming write-enable
[    3.101867] mmc0: new high speed SDHC card at address e624
[    3.111846] mmcblk0: mmc0:e624 SU08G 7.40 GiB
[    3.124359]  mmcblk0: p1 p2
[    3.130310] VUSB: disabling
[    3.134399] VANA: disabling
[    3.187194] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    3.195831] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    3.208129] devtmpfs: mounted
[    3.211975] Freeing unused kernel memory: 404K (c0807000 - c086c000)
INIT: version 2.88 booting
Starting udev
starting version 225
[    4.656524] random: systemd-udevd urandom read with 19 bits of entropy available
[    7.008209] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
Tue Dec 22 22:32:02 UTC 2015
INIT: Entering runlevel: 5
Configuring network interfaces... [   10.381103] smsc911x 2c000000.ethernet eth0: SMSC911x/921x identified at 0xf0190000, IRQ: 71
udhcpc (v1.23.2) started
Sending discover...
Sending discover...
Sending select for 192.168.10.112...
Lease of 192.168.10.112 obtained, lease time 43200
/etc/udhcpc.d/50default: Adding DNS 192.168.10.2
done.
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd
  generating ssh RSA key...
  generating ssh ECDSA key...
  generating ssh DSA key...
  generating ssh ED25519 key...
done.
Starting ntpd: done
Starting syslogd/klogd: done

Poky (Yocto Project Reference Distro) 2.0 duovero /dev/ttyO2

duovero login: [  105.580902] random: nonblocking pool is initialized

Poky (Yocto Project Reference Distro) 2.0 duovero /dev/ttyO2

duovero login: root
root@duovero:~#