Skip to content

Instantly share code, notes, and snippets.

@shibajee

shibajee/Netgear JWNR2010v5

Last active July 6, 2020 20:51
Show Gist options
  • Star 1 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save shibajee/8fb5bd3fd422a8957a3de3f7352eed45 to your computer and use it in GitHub Desktop.
Save shibajee/8fb5bd3fd422a8957a3de3f7352eed45 to your computer and use it in GitHub Desktop.
Download ZIP
Raw
Netgear JWNR2010v5
U-Boot 1.1.3 (Feb 26 2014 - 12:49:16)
Board: Ralink APSoC DRAM: 32 MB
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 16 c2 20 (2016c220)
find flash: MX25L3205D
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 256 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 32 MBytes
Flash component: SPI Flash
Date:Feb 26 2014 Time:12:49:16
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
Press Ctrl+C to Enter the Main loop...
******************************************
Uboot StandAlone Entry
****************************************** 0
******************************************
Uboot StandAlone Entry
******************************************
Enter NMRP_main
Flash Sector Number : 64.
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
NMRP_FLASH_SIZE_buffer --> a1000000.
NMRP:LISTENING
### No NMRP Server found ###
******************************************
Uboot StandAlone Entry
******************************************
Flash Sector Number : 64.
***************************************************
Sercomm Boot Version 4.00.0
***************************************************
Entering Firmware : Everything is OK.
3: System Boot system code via Flash.
## Booting image at bc020000 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1274125 Bytes = 1.2 MB
Load Address: 80000000
Entry Point: 8000c2f0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (root@localhost.localdomain) (gcc version 3.4.2) #219 Wed A ug 21 13:39:21 CST 2019
The CPU feqenuce set to 580 MHz
MIPS CPU sleep mode enabled.
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
PCIE: PLL power down for MT7620N
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock2 console=ttyS0
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00048008
Readback ErrCtl register=00048008
Memory: 27704k/32768k available (3837k kernel code, 5064k reserved, 543k data, 1 64k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:80431cf8, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 5ab11d
RALINK_GPIOMODE = 58b11d
PPLL_CFG1=0x4010000
MT7620 PPLL unlock
bio: create slab <bio-0> at 0
vgaarb: loaded
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.15)
msgmni has been set to 54
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
spidrv_major = 217
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : c2 20 16 c2 20 (2016c220)
MX25L3205D(c2 2016c220) (4096 Kbytes)
mtd .name = raspi, .size = 0x00400000 (0M) .erasesize = 0x00000004 (0K) .numeras eregions = 65536
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000000020000 : "Bootloader"
0x000000020000-0x000000160000 : "Kernel"
0x000000160000-0x0000003c0000 : "Rootfs"
0x0000003c0000-0x0000003e0000 : "Chinese UI"
0x0000003e0000-0x0000003f0000 : "SC Nvram"
0x0000003f0000-0x000000400000 : "WiFi Data"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288022
Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocate d, mtu = 1500!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288095
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== pAd = c0045000, size = 947464 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.6_edcca_monitor_20131222
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (432 buckets, 1728 max)
nf_conntrack_rtsp v0.6.21 loading
GRE over IPv4 demultiplexor driver
gre: can't add protocol
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
L2TP IP encapsulation support (L2TPv3)
L2TP netlink interface
L2TP ethernet pseudowire support (L2TPv3)
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 164k freed
init started: BusyBox v1.12.1 (2019-08-21 13:36:11 CST)
starting pid 31, tty '': '/usr/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
=System Architecture Department=
led_pb_api: module license 'Sercomm' taints kernel.
Disabling lock debugging due to kernel taint
Register LED ID <70>
Register LED ID <40>
Register LED ID <90>
Register LED ID <20>
Register LED ID <10>
Register LED ID <11>
Register LED ID <12>
Register LED ID <13>
netfilter dnshj choose interested dns queries module loaded !
init common module successful
insert firewall block module success
fake source dos protect modules is inserted
netfilter PSD and TCP/UDP Echo/Chargen Attack loaded
netfilter tcp syn flood module loaded
netfilter clamp total session for one src ip module loaded
netfilter other dos module loaded
insmod finish
Raeth v3.0 (Tasklet,SkbRecycle)
phy_tx_ring = 0x01635000, tx_ring = 0xa1635000
phy_rx_ring0 = 0x01636000, rx_ring0 = 0xa1636000
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43288095
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
device eth2.1 entered promiscuous mode
device eth2 entered promiscuous mode
[rc debug]/usr/sbin/rc init
[SYSTEM]echo "Configure 6855 ESW port base vlan mtk"
Configure 6855 ESW port base vlan mtk
[SYSTEM]switch reg w 2004 ff0003
switch reg write offset=2004, value=ff0003
[SYSTEM]switch reg w 2104 ff0003
switch reg write offset=2104, value=ff0003
[SYSTEM]switch reg w 2204 ff0003
switch reg write offset=2204, value=ff0003
[SYSTEM]switch reg w 2304 ff0003
switch reg write offset=2304, value=ff0003
[SYSTEM]switch reg w 2404 ff0003
switch reg write offset=2404, value=ff0003
[SYSTEM]switch reg w 2504 ff0003
switch reg write offset=2504, value=ff0003
[SYSTEM]switch reg w 2010 810000c0
switch reg write offset=2010, value=810000c0
[SYSTEM]switch reg w 2110 810000c0
switch reg write offset=2110, value=810000c0
[SYSTEM]switch reg w 2210 810000c0
switch reg write offset=2210, value=810000c0
[SYSTEM]switch reg w 2310 810000c0
switch reg write offset=2310, value=810000c0
[SYSTEM]switch reg w 2410 810000c0
switch reg write offset=2410, value=810000c0
[SYSTEM]switch reg w 2510 810000c0
switch reg write offset=2510, value=810000c0
[SYSTEM]switch reg w 2610 81000000
switch reg write offset=2610, value=81000000
[SYSTEM]switch reg w 2710 81000000
switch reg write offset=2710, value=81000000
[SYSTEM]switch reg w 2604 20ff0003
switch reg write offset=2604, value=20ff0003
[SYSTEM]switch reg w 2704 20ff0003
switch reg write offset=2704, value=20ff0003
[SYSTEM]switch reg w 2610 81000000
switch reg write offset=2610, value=81000000
[SYSTEM]switch reg w 2014 10001
switch reg write offset=2014, value=10001
[SYSTEM]switch reg w 2114 10001
switch reg write offset=2114, value=10001
[SYSTEM]switch reg w 2214 10001
switch reg write offset=2214, value=10001
[SYSTEM]switch reg w 2314 10001
swbr0: port 1(eth2.1) entering learning state
itbr0: port 1(eth2.1) entering learning state
ch reg write offset=2314, value=10001
[SYSTEM]switcdevice eth2 left promiscuous mode
h regbr0: port 1(eth2.1) entering learning state
w 2414 10002
switch reg write offset=2414, value=10002
[SYSTEM]switch reg w 2514 10001
device eth2 entered promiscuous mode10001
eeer0: port 1(eth2.1) entering learning state
2mbr0: port 1(eth2.1) entering learning state
[SYSTEM]switch vlan set 0 1 11110111
[SYSTEM]switch vlan set 1 2 00001011
[SYSTEM]switch clear
[SYSTEM]/sbin/ifconfig br0 down hw ether 2C:30:33:1D:81:28 up
[SYSTEM]/sbin/ifconfig eth2.1 down
[SYSTEM]/sbin/ifconfig eth2.1 hw etswitch register base addr to 0xb0117014
her 2C:30:33:1D:81:28
[SYSTEM]/sbin/ifwrite offset 0x0, value 0xe0000c
config eth2.1 up
[SYSTEM]reg s 0xb0117014
switch register base addr to 0xb0000000
[SYSTEM]reg w 0 0xe0000c
[SYSTEM]regwrite offset 0x60, value 0x18379d
s 0xb0000000
[SYSTEM]reg w 60 0x18379d
[rc.c::n300_special_region_check():405] MAC = 2C:30:33:1D:81:28
[rc.c::n300_special_region_check():406] Region = 00:00:00:02
RC: wifi_init()
rules = <>, timeout = 20
[rc debug]/usr/sbin/rc wlan restart
ap_name=wlan action=restart
[rc.c::rc_action():859] rc_action before add wlan - restart
rc action <wlan @ restart> before file_lock.
rc action <wlan @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wlan.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add wlan - restart
[rc.c::rc_stop():801] Calling Stop function of wlan
[SYSTEM]/usr/bin/killall rt2860apd
killall: rt2860apd: no process killed
[SYSTEM]/usr/bin/killall rtinicapd
killall: rtinicapd: no process killed
[SYSTEM]/sbin/ifconfig wds0 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wds0
interface wds0 does not exist!
[SYSTEM]/sbin/ifconfig wdsi0 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wdsi0
interface wdsi0 does not exist!
[SYSTEM]/sbin/ifconfig wds1 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wds1
interface wds1 does not exist!
[SYSTEM]/sbin/ifconfig wdsi1 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wdsi1
interface wdsi1 does not exist!
[SYSTEM]/sbin/ifconfig wds2 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wds2
interface wds2 does not exist!
[SYSTEM]/sbin/ifconfig wdsi2 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wdsi2
interface wdsi2 does not exist!
[SYSTEM]/sbin/ifconfig wds3 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wds3
interface wds3 does not exist!
[SYSTEM]/sbin/ifconfig wdsi3 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wdsi3
interface wdsi3 does not exist!
[SYSTEM]/sbin/ifconfig ra1 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/ifconfig rai1 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/ifconfig ra2 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/ifconfig rai2 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/ifconfig ra3 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/ifconfig rai3 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/ifconfiCan't find DB for id==41
g ra0 down
[SYSTEM]/sbin/iwpriv rai0 set RadioOCan't find DB for id==42
n=1
rai0 no private ioctls.
[SYSTEM]/sbCan't find DB for id==45
in/ifconfig rai0 down
ifconfig: SIOCGIFFLAGS: No such device
killall: nas: no process killed
killall: eapd: no process killed
killall: wps_monitor: no process killed
killall: wps_ap: no process killed
killall: wps_det: no process killed
Can't find DB for id==45
Can't find DB for id==61
Can't find DB for id==62
Can't find DB for id==63
Can't find DB for id==64
Can't find DB for id==65
Can't find DB for id==66
Can't find DB for id==67
Can't find DB for id==68
killall: wps_det: no process killed
[rc.c::rc_stardevice ra0 entered promiscuous mode
t(device ra0 left promiscuous mode
):762] Calling Start function of wlan
can't add ra0 to bridge br0: Invalid argument
[SYSTEM]mkdir -p /etc/Wireless/RT2860
sh: /usr/sbin/wsc_daemon: not found
CHIP: 7620 - current MAC: 2C:30:33:1D:81:28
Assign MAC: 2C:30:33:1D:81:28
no update!
[SYSTEM]echo 1 > /tmp/wifi_mac_set
[SYSTEM]cp -af /etc_ro/Wireless/RT2860AP/CE_22_5dbi_sku /etc_ro/Wireless/RT2860A P/SingleSKU.dat
X DESC a1ec3000 size = 2048
32m[SYSTEM]/sbin/ifconfig RTMP_TimerListAdd: add timer obj c00eda30!
raRTMP_TimerListAdd: add timer obj c00a7138!
0 RTMP_TimerListAdd: add timer obj c00a9984!
upRTMP_TimerListAdd: add timer obj c00a9a44!
TMP_TimerListAdd: add timer obj c00a9b04!
0mRTMP_TimerListAdd: add timer obj c00a9bc4!
RTMP_TimerListAdd: add timer obj c00a9c84!
RTMP_TimerListAdd: add timer obj c00a9d44!
RTMP_TimerListAdd: add timer obj c00a9e04!
RTMP_TimerListAdd: add timer obj c00a9ec4!
RTMP_TimerListAdd: add timer obj c00a9f84!
RTMP_TimerListAdd: add timer obj c00aa044!
RTMP_TimerListAdd: add timer obj c00aa104!
RTMP_TimerListAdd: add timer obj c00aa1c4!
RTMP_TimerListAdd: add timer obj c00aa284!
RTMP_TimerListAdd: add timer obj c00aa344!
RTMP_TimerListAdd: add timer obj c00aa404!
RTMP_TimerListAdd: add timer obj c00aa4c4!
RTMP_TimerListAdd: add timer obj c00a710c!
RTMP_TimerListAdd: add timer obj c00a9958!
RTMP_TimerListAdd: add timer obj c00a9a18!
RTMP_TimerListAdd: add timer obj c00a9ad8!
RTMP_TimerListAdd: add timer obj c00a9b98!
RTMP_TimerListAdd: add timer obj c00a9c58!
RTMP_TimerListAdd: add timer obj c00a9d18!
RTMP_TimerListAdd: add timer obj c00a9dd8!
RTMP_TimerListAdd: add timer obj c00a9e98!
RTMP_TimerListAdd: add timer obj c00a9f58!
RTMP_TimerListAdd: add timer obj c00aa018!
RTMP_TimerListAdd: add timer obj c00aa0d8!
RTMP_TimerListAdd: add timer obj c00aa198!
RTMP_TimerListAdd: add timer obj c00aa258!
RTMP_TimerListAdd: add timer obj c00aa318!
RTMP_TimerListAdd: add timer obj c00aa3d8!
RTMP_TimerListAdd: add timer obj c00aa498!
RTMP_TimerListAdd: add timer obj c00a70e0!
RTMP_TimerListAdd: add timer obj c00a99b0!
RTMP_TimerListAdd: add timer obj c00a9a70!
RTMP_TimerListAdd: add timer obj c00a9b30!
RTMP_TimerListAdd: add timer obj c00a9bf0!
RTMP_TimerListAdd: add timer obj c00a9cb0!
RTMP_TimerListAdd: add timer obj c00a9d70!
RTMP_TimerListAdd: add timer obj c00a9e30!
RTMP_TimerListAdd: add timer obj c00a9ef0!
RTMP_TimerListAdd: add timer obj c00a9fb0!
RTMP_TimerListAdd: add timer obj c00aa070!
RTMP_TimerListAdd: add timer obj c00aa130!
RTMP_TimerListAdd: add timer obj c00aa1f0!
RTMP_TimerListAdd: add timer obj c00aa2b0!
RTMP_TimerListAdd: add timer obj c00aa370!
RTMP_TimerListAdd: add timer obj c00aa430!
RTMP_TimerListAdd: add timer obj c00aa4f0!
RTMP_TimerListAdd: add timer obj c004e1a8!
RTMP_TimerListAdd: add timer obj c004dd9c!
RTMP_TimerListAdd: add timer obj c004e178!
RTMP_TimerListAdd: add timer obj c004e520!
RTMP_TimerListAdd: add timer obj c004e270!
RTMP_TimerListAdd: add timer obj c004e2a0!
RTMP_TimerListAdd: add timer obj c004e460!
RTMP_TimerListAdd: add timer obj c004e490!
RTMP_TimerListAdd: add timer obj c00513e0!
RTMP_TimerListAdd: add timer obj c0050fd4!
RTMP_TimerListAdd: add timer obj c00513b0!
RTMP_TimerListAdd: add timer obj c0051758!
RTMP_TimerListAdd: add timer obj c00514a8!
RTMP_TimerListAdd: add timer obj c00514d8!
RTMP_TimerListAdd: add timer obj c0051698!
RTMP_TimerListAdd: add timer obj c00516c8!
RTMP_TimerListAdd: add timer obj c0054618!
RTMP_TimerListAdd: add timer obj c005420c!
RTMP_TimerListAdd: add timer obj c00545e8!
RTMP_TimerListAdd: add timer obj c0054990!
RTMP_TimerListAdd: add timer obj c00546e0!
RTMP_TimerListAdd: add timer obj c0054710!
RTMP_TimerListAdd: add timer obj c00548d0!
RTMP_TimerListAdd: add timer obj c0054900!
RTMP_TimerListAdd: add timer obj c0057850!
RTMP_TimerListAdd: add timer obj c0057444!
RTMP_TimerListAdd: add timer obj c0057820!
RTMP_TimerListAdd: add timer obj c0057bc8!
RTMP_TimerListAdd: add timer obj c0057918!
RTMP_TimerListAdd: add timer obj c0057948!
RTMP_TimerListAdd: add timer obj c0057b08!
RTMP_TimerListAdd: add timer obj c0057b38!
RTMP_TimerListAdd: add timer obj c005aa88!
RTMP_TimerListAdd: add timer obj c005a67c!
RTMP_TimerListAdd: add timer obj c005aa58!
RTMP_TimerListAdd: add timer obj c005ae00!
RTMP_TimerListAdd: add timer obj c005ab50!
RTMP_TimerListAdd: add timer obj c005ab80!
RTMP_TimerListAdd: add timer obj c005ad40!
RTMP_TimerListAdd: add timer obj c005ad70!
RTMP_TimerListAdd: add timer obj c005dcc0!
RTMP_TimerListAdd: add timer obj c005d8b4!
RTMP_TimerListAdd: add timer obj c005dc90!
RTMP_TimerListAdd: add timer obj c005e038!
RTMP_TimerListAdd: add timer obj c005dd88!
RTMP_TimerListAdd: add timer obj c005ddb8!
RTMP_TimerListAdd: add timer obj c005df78!
RTMP_TimerListAdd: add timer obj c005dfa8!
RTMP_TimerListAdd: add timer obj c0060ef8!
RTMP_TimerListAdd: add timer obj c0060aec!
RTMP_TimerListAdd: add timer obj c0060ec8!
RTMP_TimerListAdd: add timer obj c0061270!
RTMP_TimerListAdd: add timer obj c0060fc0!
RTMP_TimerListAdd: add timer obj c0060ff0!
RTMP_TimerListAdd: add timer obj c00611b0!
RTMP_TimerListAdd: add timer obj c00611e0!
RTMP_TimerListAdd: add timer obj c0064130!
RTMP_TimerListAdd: add timer obj c0063d24!
RTMP_TimerListAdd: add timer obj c0064100!
RTMP_TimerListAdd: add timer obj c00644a8!
RTMP_TimerListAdd: add timer obj c00641f8!
RTMP_TimerListAdd: add timer obj c0064228!
RTMP_TimerListAdd: add timer obj c00643e8!
RTMP_TimerListAdd: add timer obj c0064418!
RTMP_TimerListAdd: add timer obj c00a953c!
RTMP_TimerListAdd: add timer obj c00a9130!
RTMP_TimerListAdd: add timer obj c00a950c!
RTMP_TimerListAdd: add timer obj c00a98b4!
RTMP_TimerListAdd: add timer obj c00a9604!
RTMP_TimerListAdd: add timer obj c00a9634!
RTMP_TimerListAdd: add timer obj c00a956c!
RTMP_TimerListAdd: add timer obj c00a959c!
RTMP_TimerListAdd: add timer obj c00a95cc!
RTMP_TimerListAdd: add timer obj c00c439c!
RTMP_TimerListAdd: add timer obj c00c44b8!
RTMP_TimerListAdd: add timer obj c00c43c8!
RTMP_TimerListAdd: add timer obj c00ab66c!
RTMP_TimerListAdd: add timer obj c004b668!
RTMP_TimerListAdd: add timer obj c004e8a0!
RTMP_TimerListAdd: add timer obj c0051ad8!
RTMP_TimerListAdd: add timer obj c0054d10!
RTMP_TimerListAdd: add timer obj c0057f48!
RTMP_TimerListAdd: add timer obj c005b180!
RTMP_TimerListAdd: add timer obj c005e3b8!
RTMP_TimerListAdd: add timer obj c00615f0!
RTMP_TimerListAdd: add timer obj c00ab380!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
start ch = 1, ch->num = 13
18 18 18 18
22 22 22 22 22 22 22 22
22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22
24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0x20
E2PROM: 40 MW Power Delta= -2
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj c004b264!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = -1, D2 = 7, CalCode = 19 !!!
RT6352_Temperature_Init : BBPR49 = 0xffffffff
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5
Current Temperature from BBP_R49=0xfffffff4
RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127
RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
*** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -1 -1 -1 -128 -1 -1
- -1 - -1 -1 -1 -1 -1 -1 -1, offset=-11, tuning=0
RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -12 -12 -12 -128 -12 -12 - -12 - -12 -12 -12 -12 -12 -12 -12, offset=-11, tuning=0
mp_temperature=0x00, step = +7
E2PROM: G Tssi[-7 .. +7] = -128 -12 -12 -12 -128 -12 -12 - -12 - -12 -12 -12 -12 -12 -12 -12, offset=-11, tuning=0
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= 0, phase=3d)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 0, phase=3d)
TX IQ Calibration Done!
internal ALC is not enabled in NVM !
bAutoTxAgcG = 0
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
RTMP_TimerListAdd: add timer obj c00abc24!
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
Main bssid = 2c:30:33:1d:81:28
<==== rt28xx_init, Status=0
0x1300 = 00064380
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
[SYSTEM]/bin/led_app on 40
[libscm_wl.c::GenerateUUID():112]
GUI ASCII string: 38833092-3092-1883-82d5-2c30331d8128
[libscm_wl.c::GenerateUUID():113]
GUI HEX string: 388330923092188382d52c30331d8128
[SYSTEM]/usr/bin/killall miniupnpd_wsc
killall: miniupnpd_wsc: no process killed
[SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh
[SYSTEM]/bin/sh -x /var/ralink_ap_start.sh
+ iwpriv ra0 set WscConfMode=0
+ iwpriv rai0 set WscConfMode=0
+ iwpriv ra0 set WscSetupLock=0
+ iwpriv rai0 set WscSetupLock=0
+ route add -host 239.25Can't find DB for id==42
5.255.250 dev br0
+ iwpriv ra0 set WscConfMode=7
+ miniupnpd_wscCan't find DB for id==45
-m 1 -I ra0 -P /var/run/miniupnpd.ra0 -i eth2.2 -a 192.168.1.1 -n 7777 -u 38833 092-3092-1883-82d5-2c30331d8128
/var/ralink_ap_start.sh: line 10: miniupnpd_wsc: not found
[SYSTEM]/bin/cp /proc/uptime /tmp/wlan_uptime
[SYSTEM]/bin/led_app on 42
[SYSTEM]/usr/sbin/led_app on 45
unlink running file </var/run/rc.wlan.run>
=============rc start
[rc debug]/usr/sbin/rc start
ap_name=(null) action=start
[rc.c::rc_start():762] Calling Start function of lan
rc action <lan @ start> before file_lock.
rc action <lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.lan.run
rc action < unlock = 3> after file_lock.
[SYSTEM]/usr/sbin/brctl setfd br0 1
[SYSTEM]/sbin/ifconfig br0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1 .255
[SYSTEM]/usr/sbin/brctl stp br0 off
sh: cannot create /proc/http_file/getLanIp: nonexistent directory
unlink running file </var/run/rc.lan.run>
[rc.c::rc_start():762] Calling Start function of printk
rc action <printk @ start> before file_lock.
rc action <printk @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.printk.run
rc action < unlock = 3> after file_lock.
[SYSTEM]/bin/echo 1 4 1 7 > /proc/sys/kernel/printk
unlink running file </var/run/rc.printk.run>
[rc.c::rc_start():762] Calling Start function of timezone
rc action <timezone @ start> before file_lock.
rc action <timezone @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.timezone.run
rc action < unlock = 3> after file_lock.
[SYSTEM]/bin/echo GMT+0 > /etc/TZ
unlink running file </var/run/rc.timezone.run>
[rc.c::rc_start():762] Calling Start function of syslogd
rc action <syslogd @ start> before file_lock.
rc action <syslogd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
rc action < unlock = 3> after file_lock.
[SYSTEM]/sbin/syslogd -f /etc/syslog.conf
unlink running file </var/run/rc.syslogd.run>
[rc.c::rc_start():762] Calling Start function of httpd
rc action <httpd @ start> before file_lock.
rc action <httpd @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run
rc action < unlock = 5> after file_lock.
[sc_language.c::create_language_file():396] Create link files for <English>
[sc_language.c::decompress_language():176] Try to decompress MTD </dev/mtdblock3 >
rmmod: ipt_REJECT: No such file or directory
[rc debug]/bin/rc firewall restart
ap_name=firewall action=restart
[rc.c::rc_action():859] rc_action before add firewall - restart
rc action <firewall @ restart> before file_lock.
rc action <firewall @ restart lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
rc action < unlock = 5> after file_lock.
[rc.c::rc_action():867] rc_action after add firewall - restart
unlink running file </var/run/rc.firewall.run>
[rc.c::rc_action():859] rc_action before add firewall - restart
rc action <firewall @ restart> before file_lock.
rc action <firewall @ restart lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
rc action < unlock = 5> after file_lock.
[rc.c::rc_action():867] rc_action after add firewall - restart
[rc.c::rc_stop():801] Calling Stop function of firewall
[SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent director y
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent dire ctory
[rc.c::rc_start():762] Calling Start function of firewall
[SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd &
[rc debug]/usr/sbin/rc syslogd create
ap_name=syslogd action=create
[rc.c::rc_action():859] rc_action before add syslogd - create
rc action <syslogd @ create> before file_lock.
rc action <syslogd @ create lock = 6> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
rc action < unlock = 6> after file_lock.
[rc.c::rc_action():867] rc_action after add syslogd - create
[rc.c::rc_create():843] Calling Create function of syslogd
unlink running file </var/run/rc.syslogd.run>
[SYSTEM]/bin/echo switch=on > /proc/net/spi_enable
[SYSTEM]/bin/echo clear > /proc/net/firewall_block
[SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src
[SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan
[SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config
[SYSTEM]/bin/echo wan_if=eth2.2 > /proc/net/spi_enable
[SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable
fw_pt
[SYSTEM]/bin/echo "enable_ipmac=0" > /proc/arp_protect_enable
sh: cannot create /proc/arp_protect_enable: nonexistent directory
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]/bin/echo GMT+0 > /etc/TZ
[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory
unlink running file </var/run/rc.firewall.run>
[SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR JWNR2010v5" -c '**.cgi' -t 300&
[SYSTEM]/bin/ln -sf /www/style/top_netgear.css /tmp/top.css
[SYSTEM]/bin/ln -sf /www/style/basic_netgear.css /tmp/basic.css
[SYSTEM]/bin/ln -sf /www/style/advanced_netgear.css /tmp/advanced.css
[SYSTEM]/bin/ln -sf /www/style/top_style_netgear.css /tmp/top_style.css
[SYSTEM]/bin/ln -sf /www/style/hijack_style_netgear.css /tmp/hijack_style.css
[basic/httpd_cfg.c::start_remote_httpd():69] not enable two httpd
unlink running file </var/run/rc.httpd.run>
[rc.c::rc_start():762] Calling Start function of remote_httpd
rc action <remote_httpd @ start> before file_lock.
rc action <remote_httpd @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.remote_httpd.run
rc action < unlock = 5> after file_lock.
[basic/httpd_cfg.c::start_remote_httpd():69] not enable two httpd
unlink running file </var/run/rc.remote_httpd.run>
[rc.c::rc_start():762] Calling Start function of dhcpd
rc action <dhcpd @ start> before file_lock.
rc action <dhcpd @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run
rc action < unlock = 5> after file_lock.
killall: udhcpd: no process killed
unlink running file </var/run/rc.dhcpd.run>
[rc.c::rc_start():762] Calling Start function of ntp
rc action <ntp @ start> before file_lock.
rc action <ntp @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ntp.run
rc action < unlock = 5> after file_lock.
[SYSTEM]/usr/sbin/netgear_ntp -z GMT+0&
unlink running file </var/run/rc.ntp.run>
[rc.c::rc_start():762] Calling Start function of hw_nat
rc action <hw_nat @ start> before file_lock.
rc action <hw_nat @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.hw_nat.run
rc action < unlock = 5> after file_lock.
[SYSTEM]/bin/insmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko
insmod: can't read '/lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko': No suc h file or directory
unlink running file </var/run/rc.hw_nat.run>
[rc.c::rc_start():762] Calling Start function of route
rc action <route @ start> before file_lock.
rc action <route @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
rc action < unlock = 5> after file_lock.
unlink running file </var/run/rc.route.run>
[rc.c::rc_start():762] Calling Start function of ripd
rc action <ripd @ start> before file_lock.
rc action <ripd @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ripd.run
rc action < unlock = 5> after file_lock.
unlink running file </var/run/rc.ripd.run>
[rc.c::rc_start():762] Calling Start function of dnrd
rc action <dnrd @ start> before file_lock.
rc action <dnrd @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
rc action < unlock = 5> after file_lock.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192. 168.1.1:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192. 168.1.1
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
killall: dnrd: no process killed
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192. 168.1.1
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192. 168.1.1
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192 .168.1.1:80
[SYSTEM]dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.com &
unlink running file </var/run/rc.dnrd.run>
[rc.c::rc_start():762] Calling Start function of lltd
rc action <lltd @ start> before file_lock.
rc action <lltd @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.lltd.run
rc action < unlock = 5> after file_lock.
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only t he /etc/dnrd/master file or use -m off.
unlink running file </var/run/rc.lltd.run>
[rc.c::rc_start():762] Calling Start function of wlan
rc action <wlan @ start> before file_lock.
rc action <wlan @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wlan.run
rc action < unlock = 5> after file_lock.
[SYSTEM]mkdir -p /etc/Wireless/RT2860
sh: /usr/sbin/wsc_daemon: not found
[SYSTEM]cp -af /etc_ro/Wireless/RT2860AP/CE_22_5dbi_sku /etc_ro/Wireless/RT2860A P/SingleSKU.dat
[SYSTEM]/sbin/ifconfig ra0 up
[SYSTEM]/bin/led_app on 40
[libscm_wl.c::GenerateUUID():112]
GUI ASCII string: 38833092-3092-1883-9b56-2c30331d8128
[libscm_wl.c::GenerateUUID():113]
GUI HEX string: 38833092309218839b562c30331d8128
[SYSTEM]/usr/bin/killall miniupnpd_wsc
killall: miniupnpd_wsc: no process killed
[SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh
[SYSTEM]/bin/sh -x /var/ralink_ap_start.sh
+ iwpriv ra0 set WscConfMode=0
+ iwpriv rai0 set WscConfMode=0
+ iwpriv ra0 set WscSetupLock=0
+ iwpriv rai0 set WscSetupLock=0
+ route add -host 239.255.255.250 dev br0
+ iwpriv ra0 set WscConfMode=7
+ miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -i eth2.2 -a 192.168.1.1 - n 7777 -u 38833092-3092-1883-9b56-2c30331d8128
/var/ralink_ap_start.sh: line 10: miniupnpd_wsc: not found
[SYSTEM]/bin/cp /proc/uptime /tmp/wlan_uptime
[SYSTEM]/bin/led_app on 42
[SYSTEM]/usr/sbin/led_app on 45
unlink running file </var/run/rc.wlan.run>
[rc.c::rc_start():762] Calling Start function of debug_mode
rc action <debug_mode @ start> before file_lock.
rc action <debug_mode @ start lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.debug_mode.run
rc action < unlock = 5> after file_lock.
unlink running file </var/run/rc.debug_mode.run>
[rc.c::rc_start():762] Calling Start function of wifi_isolation
rc action <wifi_isolation @ start> before file_lock.
rc action <wifi_isolation @ start lock = 6> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run
rc action < unlock = 6> after file_lock.
[SYSTEM]/bin/echo "lan_ip=192.168.1.1" > /proc/wifi_isolation
sh: cannot create /proc/wifi_isolation: nonexistent directory
[SYSTEM]/bin/echo "lan_netmask=255.255.255.0" > /proc/wifi_isolation
sh: cannot create /proc/wifi_isolation: nonexistent directory
unlink running file </var/run/rc.wifi_isolation.run>
=============rc finish
[flash.c::sc_check_remotescfgmgrmagic():788] buf:ff, ff, ff, ff
[flash.c::sc_check_remotescfgmgrmagic():790] magic:31, 3e, c5, 8d
scfgmgr for local
PID USER VSZ STAT COMMAND
1 root 1528 S init
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW [kworker/u:0]
6 root 0 SW< [khelper]
7 root 0 SW [sync_supers]
8 root 0 SW [bdi-default]
9 root 0 SW< [kblockd]
10 root 0 SW [kswapd0]
11 root 0 SW< [crypto]
16 root 0 SW [mtdblock0]
17 root 0 SW [mtdblock1]
18 root 0 SW [mtdblock2]
19 root 0 SW [mtdblock3]
20 root 0 SW [mtdblock4]
21 root 0 SW [mtdblock5]
22 root 0 SW [kworker/u:1]
29 root 0 SW [kworker/0:1]
31 root 1528 S /bin/sh /usr/etc/rcS
100 root 1112 S /sbin/klogd
102 root 808 S /usr/sbin/cmd_agent_ap
345 root 0 SW [RtmpCmdQTask]
346 root 0 SW [RtmpWscTask]
399 root 1172 S /sbin/syslogd -f /etc/syslog.conf
830 root 1176 S /usr/sbin/mini_httpd -d /www -r NETGEAR JWNR2010v5 -c
845 root 940 S /usr/sbin/udhcpd /etc/udhcpd.conf
849 root 820 S /usr/sbin/netgear_ntp -z GMT+0
1386 root 1628 S dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.co
1388 root 1216 S /usr/bin/lld2 br0
1434 root 828 S telnetenabled 192.168.1.1 2C30331D8128 Gearguy Geardo
1443 root 1676 S /usr/sbin/scfgmgr
1444 root 1528 R /bin/ps
[rc debug]/usr/sbin/rc upnp start
ap_name=upnp action=start
[rc.c::rc_action():859] rc_action before add upnp - start
rc action <upnp @ start> before file_lock.
rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add upnp - start
unlink running file </var/run/rc.upnp.run>
[rc.c::rc_action():859] rc_action before add upnp - start
rc action <upnp @ start> before file_lock.
rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add upnp - start
unlink running file </var/run/rc.upnp.run>
can't find this application
[rc.c::rc_action():859] rc_action before add upnp - start
rc action <upnp @ start> before file_lock.
rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add upnp - start
[rc.c::rc_start():762] Calling Start function of upnp
[SYSTEM]route add -net 239.0.0.0 netmask 255.0.0.0 br0
[SYSTEM]/usr/sbin/miniupnpd -i eth2.2 -a 192.168.1.1 -p 56688 -U -t 1800 -T 4 -u 824ff22b-8c7d-41c5-a131-2c30331d8128
unlink running file </var/run/rc.upnp.run>
route: SIOCADDRT: File exists
/usr/etc/rcS: line 176: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
/usr/etc/rcS: line 177: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwardi ng: nonexistent directory
/usr/etc/rcS: line 181: cannot create /proc/sys/net/ipv4/conf/eth1/rp_filter: no nexistent directory
[rc debug]usr/sbin/rc wan start
[SYSTEM]/usr/sbin/brctl delif br0 eth2.2
[rc debug]/usr/sbin/rc reset_lan start
ap_name=reset_lan action=start
[rc.c::rc_action():859] rc_action before add reset_lan - start
rc action <reset_lan @ start> before file_lock.
rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
device eth2.2 is not a slave of br0
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add reset_lan - start
unlink running file </var/run/rc.reset_lan.run>
[rc.c::rc_action():859] rc_action before add reset_lan - start
rc action <reset_lan @ start> before file_lock.
rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
[SYSTEM]/usr/bin/killall netgear_ntp
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add reset_lan - start
unlink running file </var/run/rc.reset_lan.run>
can't find this application
[rc.c::rc_action():859] rc_action before add reset_lan - start
rc action <reset_lan @ start> before file_lock.
rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add reset_lan - start
[rc.c::rc_start():762] Calling Start function of reset_lan
[SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd
killall: ripd: no process killed
killall: zebra: no process killed
killall: ripd: no process killed
killall: zebra: no process killed
[SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING
[SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth2.2 -j MASQUERADE
[SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth2.2 -d ! (null) -j DROP
sh: syntax error: "(" unexpected
[SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down
[SYSTEM]/usr/bin/killall pppd
killall: pppd: no process killed
[SYSTEM]/usr/bin/killall openl2tpd
killall: openl2tpd: no process killed
[SYSTEM]/usr/bin/killall udhcpc
killall: udhcpc: no process killed
[SYSTEM]/usr/bin/killall pppoe-relay
killall: pppoe-relay: no process killed
[SYSTEM]/sbin/ifconfig eth2.2 0.0.0.0 >/dev/null 2>&1
[SYSTEM]/sbin/ifconfig eth2.2 down
[SYSTEM]/sbin/ifconfig eth2.2 hw ether 2C:30:33:1d:81:29
[SYSTEM]/sbin/ifconfig eth2.2 up
[SYSTEM]/sbin/ifconfig eth2.2 mtu 1500
[wan/wan.c::start_wan():1337] wan_mode is <dhcpc>
[SYSTEM]/bin/insmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko
insmod: can't read '/lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko': No suc h file or directory
[SYSTEM]/usr/sbin/udhcpc -i eth2.2 -s /etc/udhcpc.script -H "JWNR2010v5" &
unlink running file </var/run/rc.reset_lan.run>
PID USER VSZ STAT COMMAND
1 root 1528 S init
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW [kworker/u:0]
6 root 0 SW< [khelper]
7 root 0 SW [sync_supers]
8 root 0 SW [bdi-default]
9 root 0 SW< [kblockd]
10 root 0 SW [kswapd0]
11 root 0 SW< [crypto]
16 root 0 SW [mtdblock0]
17 root 0 SW [mtdblock1]
18 root 0 SW [mtdblock2]
19 root 0 SW [mtdblock3]
20 root 0 SW [mtdblock4]
21 rooCan't find DB for id==30
t 0 SW [mtdblock5]
22 root 0 SW [kworker/u:1]
29 root 0 SW [kworker/0:1]
31 root 1528 S /bin/sh /usr/etc/rcS
100 root 1112 S /sbin/klogd
102 root 808 S /usr/sbin/cmd_agent_ap
345 root 0 SW [RtmpCmdQTask]
346 root 0 SW [RtmpWscTask]
399 root 1172 S /sbin/syslogd -f /etc/syslog.conf
830 root 1176 S /usr/sbin/mini_httpd -d /www -r NETGEAR JWNR2010v5 -c
845 root 940 S /usr/sbin/udhcpd /etc/udhcpd.conf
1386 root 1628 S dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.co
1388 root 1216 S /usr/bin/lld2 br0
1434 root 828 S telnetenabled 192.168.1.1 2C30331D8128 Gearguy Geardo
1443 root 1676 S /usr/sbin/scfgmgr
1457 root 2012 S /usr/sbin/miniupnpd -i eth2.2 -a 192.168.1.1 -p 56688
1458 root 828 S /usr/sbin/crond
1459 root 1924 S /usr/sbin/multi_pb_app
1482 root 816 S /usr/sbin/cmd_agent
1715 root 852 S /usr/sbin/udhcpc -i eth2.2 -s /etc/udhcpc.script -H J
1721 root 1528 R /bin/sh /usr/etc/rcS
1722 root 1528 R /bin/ps
/usr/etc/rcS: line 219: /usr/sbin/led_test: not found
starting pid 1725, tty '/dev/ttyS1': '/bin/sh'
# cable_down_once
[rc debug]/usr/sbin/rc down_manage stop
ap_name=down_manage action=stop
[rc.c::rc_action():859] rc_action before add down_manage - stop
rc action <down_manage @ stop> before file_lock.
rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add down_manage - stop
unlink running file </var/run/rc.down_manage.run>
[rc.c::rc_action():859] rc_action before add down_manage - stop
rc action <down_manage @ stop> before file_lock.
rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
==================
interface=eth2.2
PATH=/bin:/sbin:/usr/sbin:/usr/bin
HOME=/
route_related_options_del_file=/tmp/dhcpc_route_related_options_del
==================
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add down_manage - stop
unlink running file </var/run/rc.down_manage.run>
can't find this application
[rc.c::rc_action():859] rc_action before add down_manage - stop
rc action <down_manage @ stop> before file_lock.
rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
rm: cannot remove '/tmp/wan_uptime': No such file or directory
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():867] rc_action after add down_manage - stop
unlink running file </var/run/r_route_related_options_del
[rc debug]/usr/sbin/rc route restart
ap_name=route action=restart
[rc.c::rc_action():859] rc_action before add route - restart
rc action <route @ restart> before file_lock.
rc action <route @ restart lock = 5> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
rc action < unlock = 5> after file_lock.
[rc.c::rc_action():867] rc_action after add route - restart
[rc.c::rc_stop():801] Calling Stop function of route
[rc.c::rc_start():762] Calling Start function of route
unlink running file </var/run/rc.route.run>
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment