Bus Pirate 5 fail

buspirate5.txt

ci-buspirate5-main-d721092.zip

id.txt

HiZ> i

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditio
ns: (1) this device may not cause harmful interference, and (2) this device must accept any interferen
ce received, including interference that may cause undesired operation.


Bus Pirate 5 REV10
Firmware v0.1.0 (commit unknown)
RP2040 with 264KB RAM, 128Mbit FLASH
S/N: 244B38D3012961E4
https://BusPirate.com/
Storage:   0.10GB (FAT16 File System)

Configuration file: Loaded
Available modes: HiZ 1-WIRE UART I2C SPI 2WIRE LED
Active mode: HiZ ()=()
Display format: Auto

selftest.txt

SELF TEST STARTING
DISABLE IRQ: OK
ADC SUBSYSTEM: VUSB  5.12V OK
FLASH STORAGE: OK
PSU ENABLE: OK
VREG==VOUT:  3390 = 3385 OK
BIO FLOAT TEST (SHOULD BE 0/<0.30V)
BIO0 FLOAT: 0/0.06V OK
BIO1 FLOAT: 0/0.06V OK
BIO2 FLOAT: 0/0.05V OK
BIO3 FLOAT: 0/0.07V OK
BIO4 FLOAT: 0/0.06V OK
BIO5 FLOAT: 0/0.06V OK
BIO6 FLOAT: 0/0.07V OK
BIO7 FLOAT: 0/0.08V OK
BIO HIGH TEST (SHOULD BE >3.00V)
BIO0 HIGH: 3.38V OK
BIO1 HIGH: 3.38V OK
BIO2 HIGH: 3.38V OK
BIO3 HIGH: 3.39V OK
BIO4 HIGH: 3.38V OK
BIO5 HIGH: 3.38V OK
BIO6 HIGH: 3.38V OK
BIO7 HIGH: 3.38V OK
BIO LOW TEST (SHOULD BE <0.30V)
BIO0 LOW: 0.05V OK
BIO1 LOW: 0.04V OK
BIO2 LOW: 0.05V OK
BIO3 LOW: 0.04V OK
BIO4 LOW: 0.04V OK
BIO5 LOW: 0.05V OK
BIO6 LOW: 0.04V OK
BIO7 LOW: 0.05V OK
BIO PULL-UP HIGH TEST (SHOULD BE 1/>3.00V)
BIO0 PU-HIGH: 1/3.34V OK
BIO1 PU-HIGH: 1/3.35V OK
BIO2 PU-HIGH: 1/3.32V OK
BIO3 PU-HIGH: 1/3.36V OK
BIO4 PU-HIGH: 1/3.38V OK
BIO5 PU-HIGH: 1/3.35V OK
BIO6 PU-HIGH: 1/3.32V OK
BIO7 PU-HIGH: 1/3.32V OK
BIO PULL-UP LOW TEST (SHOULD BE <0.30V)
BIO0 PU-LOW: 0.15V OK
BIO1 PU-LOW: 0.15V OK
BIO2 PU-LOW: 0.16V OK
BIO3 PU-LOW: 0.16V OK
BIO4 PU-LOW: 0.15V OK
BIO5 PU-LOW: 0.15V OK
BIO6 PU-LOW: 0.15V OK
BIO7 PU-LOW: 0.16V OK
CURRENT OVERRIDE: PPSU CODE 1, ERROR!
CURRENT LIMIT TEST: PPSU CODE 0, ADC: 2061, ERROR!
PPSU CODE 0, ADC: 2061, ERROR!
PPSU CODE 0, ADC: 2062, ERROR!
PPSU CODE 0, ADC: 2062, ERROR!
PPSU CODE 0, ADC: 2061, ERROR!
PUSH BUTTON TO COMPLETE: OK

ERRORS: 2
FAIL! :(

winbond.txt

SPI> flash read -f flash1.bin
Flash device manufacturer ID 0xEF, type ID 0x30, capacity ID 0x13
Error: SFDP signature error. It must be 0x50444653 'SFDP'
Warning: Read SFDP parameter header information failed. The SPI_FLASH does not support JEDEC SFDP.
Found a Winbond W25X40CL flash chip (524288 bytes)
Flash device reset success
Dumping to flash1.bin...
[o o o o o o o o o o ]
Dump OK

SPI> ls
        80 bpspi.bp
         0 flash1.bin
0 dirs, 2 files