boot log of Sky SR101 router

output.log

HELO
CPUI
L1CI
HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LASY
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 1.0.38-112.37 for BCM96362 (32bit,SP,BE)
Build Date: Fri Jul 20 14:05:13 BST 2012 (nkumar@cheese)
Copyright (C) 2000-2011 Broadcom Corporation.

HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
Total Flash size: 16384K with 256 sectors
Chip ID: BCM6362B0, MIPS: 400MHz, DDR: 333MHz, Bus: 166MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.0.1:ffffff00  
Host IP address                   : 192.168.0.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-10)                   : Meerkat  
Number of MAC Addresses (1-32)    : 10  
Base MAC Address                  : <redacted>  
PSI Size (1-64) KBytes            : 40  
Enable Backup PSI [0|1]           : 0  
System Log Size (0-256) KBytes    : 0  
Main Thread Number [0|1]          : 0  
GPON Serial Number                : "BRCM12345678"  
GPON Password                     : "          "  
Device Pin                        : "12345670"  

Booting from only image (0xb8040000) ...

Found Signature!

SIGNATURE OK
Code Address: 0x80010000, Entry Address: 0x80324ac0
Decompression OK!
Entry at 0x80324ac0
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80324ac0
Linux version 3.4.11-rt19 (build@vm001738) (gcc version 4.6.2 (Buildroot 2011.11) ) #1 SMP PREEMPT Mon Apr 10 15:11:06 BST 2017

HS Serial flash device: S25FL128, id 0x0118 size 16384KB

macaddr - <redacted>

bootline = e=192.168.0.1:ffffff00 h=192.168.0.100 g= r=f f=vmlinux i=bcm963xx_fs_kernel d=1 p=0 ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿMeerkat 

szBoardId 0x8050ed88

szVoiceBoardId 0x8050eefc

ulNumMacAddrs 0xa

ulPsiSize 0x28

ulPsiSize 0x28

backupPsi 0x0

ulSyslogSize 0x0

Meerkat prom init

CPU revision is: 0002a070 (Broadcom BMIPS4350)

DSL SDRAM reserved: 0x100000

Determined physical RAM map:

 memory: 07f00000 @ 00000000 (usable)

Zone PFN ranges:

  DMA      0x00000000 -> 0x00001000

  Normal   0x00001000 -> 0x00007f00

Movable zone start PFN for each node

Early memory PFN ranges

    0: 0x00000000 -> 0x00007f00

On node 0 totalpages: 32512

free_area_init_node: node 0, pgdat 803bda70, node_mem_map 81000000

  DMA zone: 32 pages used for memmap

  DMA zone: 0 pages reserved

  DMA zone: 4064 pages, LIFO batch:0

  Normal zone: 222 pages used for memmap

  Normal zone: 28194 pages, LIFO batch:7

PERCPU: Embedded 7 pages/cpu @81103000 s5088 r8192 d15392 u32768

pcpu-alloc: s5088 r8192 d15392 u32768 alloc=8*4096

pcpu-alloc: [0] 0 [0] 1 

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32258

Kernel command line: ro noinitrd  irqaffinity=0

PID hash table entries: 512 (order: -1, 2048 bytes)

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

Memory: 123576k/130048k available (3206k kernel code, 6472k reserved, 562k data, 204k init, 0k highmem)

Preemptible hierarchical RCU implementation.

NR_IRQS:128

console [ttyS0] enabled

Calibrating delay loop... 397.31 BogoMIPS (lpj=198656)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

--Kernel Config--

  SMP=1

  PREEMPT=1

  DEBUG_SPINLOCK=0

  DEBUG_MUTEXES=0

Broadcom Logger v0.1 Apr 10 2017 15:09:55

CPU revision is: 0002a070 (Broadcom BMIPS4350)

Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

Brought up 2 CPUs

NET: Registered protocol family 16

Total Flash size: 16384K with 256 sectors

Flash split 255 : AuxFS[1638400]

registering PCI controller with io_map_base unset

registering PCI controller with io_map_base unset

bio: create slab <bio-0> at 0

PCI host bridge to bus 0000:00

pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]

pci_bus 0000:00: root bus resource [io  0x12000000-0x1200ffff]

pci 0000:00:00.0: [14e4:435f] type 00 class 0x028000

pci 0000:00:00.0: reg 10: [mem 0x10004000-0x10005fff]

PCI host bridge to bus 0000:01

pci_bus 0000:01: root bus resource [mem 0xa0000000-0xa0ffffff]

pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]

pci 0000:01:00.0: [14e4:6362] type 01 class 0x060400

pci 0000:01:00.0: PME# supported from D0 D3hot

pci 0000:01:00.0: PCI bridge to [bus 02-02]

bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated

bcmleg_spi bcmleg_spi.0: master is unqueued, this is deprecated

skbFreeTask created successfully

BLOG v3.0 Initialized

BLOG Rule v1.0 Initialized

Broadcom IQoS v0.1 Apr 10 2017 15:10:56 initialized

Broadcom GBPM v0.1 Apr 10 2017 15:10:57 initialized

NET: Registered protocol family 8

NET: Registered protocol family 20

nfc: nfc_init: NFC Core ver 0.1

NET: Registered protocol family 39

Switching to clocksource MIPS

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP: reno registered

UDP hash table entries: 128 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)

NET: Registered protocol family 1

PCI: CLS 64 bytes, default 16

bcm_tstamp initialized, (hpt_freq=200000000 2us_div=200 2ns_mult=5 2ns_shift=0)

squashfs: version 4.0 (2009/01/31) Phillip Lougher

jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

msgmni has been set to 241

io scheduler noop registered (default)

bcm963xx_mtd driver

File system address: 0xb8040100

Registered device mtd:rootfs dev0 Address=0xb8040100 Size=7790592

Registered device mtd:data dev1 Address=0xb8e60000 Size=1638400

PPP generic driver version 2.4.2

PPP BSD Compression module registered

PPP Deflate Compression module registered

NET: Registered protocol family 24

i2c /dev entries driver

Initalisg watchdog: WatchDogDefCount=2000000000 

brcmboard: brcm_board_init entry

kerSysScreenPciDevices: 0x14e4:0x435f:(slot 0) detected

kerSysScreenPciDevices: 0x14e4:0x6362:(slot 0) detected

SES: Button Interrupt 0x1 is enabled

SES: LED GPIO 0x8010 is enabled

Serial: BCM63XX driver $Revision: 3.00 $

Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)

ttyS0 at MMIO 0xb0000100 (irq = 11) is a BCM63XX

ttyS1 at MMIO 0xb0000120 (irq = 12) is a BCM63XX

Total # RxBds=2845

bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized


bcmPktDma_init: Broadcom Packet DMA Library initialized

bcmxtmrt: Broadcom BCM6362B0 ATM/PTM Network Device v0.3 Apr 10 2017 15:10:44

IPSEC SPU: SUCCEEDED 

GACT probability NOT on

Mirror/redirect action on

netem: version 1.3

u32 classifier

    input device check on

    Actions configured

xt_time: kernel timezone is -0000

TCP: cubic registered

Initializing XFRM netlink socket

NET: Registered protocol family 10

IPv6 over IPv4 tunneling driver

NET: Registered protocol family 17

NET: Registered protocol family 15

Initializing MCPD Module

Ebtables v2.0 registered

ebt_time registered

ebt_ftos registered

ebt_wmm_mark registered

8021q: 802.1Q VLAN Support v1.8

VFS: Mounted root (squashfs filesystem) readonly on device 31:0.

Freeing unused kernel memory: 204k freed


init started: BusyBox v1.17.2 (2017-04-10 15:12:32 BST)

starting pid 193, tty '': '/bin/sh -l -c "bcm_boot_launcher start"'
Mounting filesystems...
Configuring system...
Loading drivers and kernel modules... 

chipinfo: module license 'proprietary' taints kernel.

Disabling lock debugging due to kernel taint

brcmchipinfo: brcm_chipinfo_init entry

Broadcom Ingress QoS Module  Char Driver v0.1 Apr 10 2017 15:10:19 Registered<243>


Broadcom Ingress QoS ver 0.1 initialized

BPM: tot_mem_size=134217728B (128MB), buf_mem_size <15%> =20132655B (19MB), num of buffers=9986, buf size=2016

Broadcom BPM Module Char Driver v0.1 Apr 10 2017 15:10:10 Registered<244>

NBUFF v1.0 Initialized

Initialized fcache state

Broadcom Packet Flow Cache  Char Driver v2.2 Apr 10 2017 15:10:19 Registered<242>

Created Proc FS /procfs/fcache

Broadcom Packet Flow Cache registered with netdev chain

Broadcom Packet Flow Cache learning via BLOG enabled.

[FHW]  pktDbgLvl[0xc00c81d0]=0

[FHW]  fhw_construct: 

Initialized Fcache HW accelerator layer state

flwStatsThread created

Constructed Broadcom Packet Flow Cache v2.2 Apr 10 2017 15:10:19

chipId 0x636220B0

Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Apr 10 2017 15:10:10 Registered <241>

Enabling SMISBUS PHYS_FAP_BASE[0] is 0x14001000

FAP Soft Reset Done

4ke Reset Done

FAP Debug values at 0xa5d9fee0 0xa5d9fee0

fapGso_LoopBkThread created successfully

Allocated FAP0 SWQ_HOST2FAP_GSO_LOOPBACK_Q mem=a7970000 : 16384 bytes

Allocated FAP0 SWQ_FAP2HOST_GSO_LOOPBACK_Q mem=a7a40000 : 16384 bytes

GSO LOOPBACK Cached HOST2FAP Q INFO:

 Swq =b1015fb0 qStart=a7970000 qEnd=a7974000 msgSize=4 dqm=18 fapId=0

GSO LOOPBACK Cached FAP2HOST Q INFO:

 Swq =b1015f90 qStart=a7a40000 qEnd=a7a44000 msgSize=2 dqm=19 fapId=0

Allocated FAP0 TM SDRAM Queue Storage (a5db0f70) : 341376 bytes @ a5e00000

[NTC fapProto] fapReset  : Reset FAP Protocol layer

[FAP0] DSPRAM : stack <0x80004000><1536>, global <0x80004600><4008>, free <2648>, total<8192>

[FAP0] PSM : addr<0xE0010000>, used <24528>, free <8240>, total <32768>

[FAP0] DQM : availableMemory 14660 bytes, nextByteAddress 0xE0004600

[FAP0] Initializing FAP4KE GSO LOOPBACK on fapIdx=0 ...

[FAP0] SWQ: HOST2FAP_GSO_LOOPBACK 

[FAP0] >>>>------------------

[FAP0] swq =e0015fb0 msgSize =4 words , maxDepth=1024

[FAP0] qStart =a7970000 qEnd=a7974000

[FAP0] rdPtr =a7970000 wrPtr=a7970000 count=0

[FAP0]  processed =0 dropped =0 

[FAP0]  Associated DQM=18 dir HOST2FAP

[FAP0] ------------------<<<<

[FAP0] SWQ: FAP2HOST_GSO_LOOPBACK 

[FAP0] >>>>------------------

[FAP0] swq =e0015f90 msgSize =2 words , maxDepth=2048

[FAP0] qStart =a7a40000 qEnd=a7a44000

[FAP0] rdPtr =a7a40000 wrPtr=a7a40000 count=0

[FAP0]  processed =0 dropped =0 

[FAP0]  Associated DQM=19 dir FAP2HOST

[FAP0] ------------------<<<<

[FAP0] FAP4KE GSO LOOPBACK Init Done...

[FAP0] FAP BPM Initialized.

Broadcom Packet Flow Cache HW acceleration enabled.

fapDrv_construct: FAP0: pManagedMemory=b1010650. wastage 8 bytes

bcmPktDma_bind: FAP Driver binding successfull

[FAP0] FAP TM: ON

bcmxtmcfg: bcmxtmcfg_init entry

adsl: adsl_init entry

Broadcom BCM6362B0 Ethernet Network Device v0.1 Apr 10 2017 15:10:35

fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b1010650 bytes remaining 7000

ETH Init: Ch:0 - 200 tx BDs at 0xb1010650

fapDrv_psmAlloc: wastage 8 bytes

fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b1011910 bytes remaining 2184

ETH Init: Ch:0 - 600 rx BDs at 0xb1011910

[FAP0] enetRxChannel 0

ETH Init: Ch:1 - 1997 rx BDs at 0xa5c48000

dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered 

eth0: MAC Address: <redacted>

eth1: MAC Address: <redacted>

eth2: MAC Address: <redacted>

eth3: MAC Address: <redacted>

NComm TMS V6.80 Kernel Module loaded.

[NTC arl] arlEnable : Enabled ARL binding to FAP

Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Apr 10 2017 15:10:09 Registered <245>

_set_by_buildFS_-------------------Loading wl.ko (NON MESH)---------------------------
--SMP support

wl: dsl_tx_pkt_flush_len=338

wl: norm_wmark_tot=3643, pktc_wmark_tot=3643

Initializing WLCSM Module

wl 0000:00:00.0: setting latency timer to 64

wl: passivemode=1

wl0: creating kthread wl0-kthrd

wl0: creating timer kthread wl0-tmr-kthrd

wl: napimode=0

Neither SPROM nor OTP has valid image

wl:srom/otp not programmed, using main memory mapped srom info(wombo board)

wl:loading /etc/wlan/bcm6362_map.bin

srom rev:8

wl0: allocskbmode=1 currallocskbsz=512

+++++ Added gso loopback support for dev=wl0 <86ab7800>

wl0: Broadcom BCM435f 802.11 Wireless Controller 6.37.14.4803.cpe4.14L04.0-kdb

dgasp: kerSysRegisterDyingGaspHandler: wl0 registered 

Broadcom 802.1Q VLAN Interface, v0.1

PCIe: No device found - Powering down

Starting SWMDK...
Note: Loading 6300 MDK (default) driver for 6362 chip 
Switch MDK: num_switches = 1
Switch MDK: unit = 0; phy_pbmp = 0x3f; config_pbmp = 0x3f 
Switch MDK link poll thread: unit=0; phypbmp=0x3f config_pbmp=0x3f
AutoNeg is disabledand Speed has changed

AutoNeg is disabledand Speed has changed

applyiing SKY specifig config...
Success 
Saving kernel bootup messages for dumpsysinfo...
Starting CMS smd...

===== Release Version 3.50.2116.R 170410_1511 =====

Initializing CMS MDM in Hybrid98+181 mode
ssk:error:10.915:rcl_skyHealthMonitorCfgObject:256:object is not more used, please use SkyDiagn[   10.922000] DDR Self Refresh pwrsaving is enabled

[   10.928000] Energy Efficient Ethernet is disabled

[   10.933000] Adaptive Voltage Scaling is now enabled

ostics object 
[   10.941000] BcmPwrMngtEnableAvs: AVS_START, 0x8785c048

[   11.367000] ip_tables: (C) 2000-2006 Netfilter Core Team

[   11.647000] ip6_tables: (C) 2000-2006 Netfilter Core Team

[   12.011000] ADDRCONF(NETDEV_UP): br0: link is not ready

[   12.258000] Netfilter messages via NETLINK v0.30.

ssk:error:12.417:rcl_lanIpIntfObject:326:Turning off TX offload on br0 interface
sh: ethtool: not found
[   12.576000] nf_conntrack version 0.5.0 (1934 buckets, 7736 max)

[   13.854000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0

[   13.860000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.

RTNETLINK answers: No such file or directory
RTNETLINK answers: No such process
RTNETLINK answers: No such process
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such process
RTNETLINK answers: No such process
ip6tables: No chain/target/match by that name.
RTNETLINK answers: File exists
RTNETLINK answers: File exists
RTNETLINK answers: No such process
RTNETLINK answers: No such file or directory
RTNETLINK answers: File exists
RTNETLINK answers: File exists
Warning: never matched protocol: 51. use extension match instead.
[   17.392000] device eth0 entered promiscuous mode

[   17.437000] ADDRCONF(NETDEV_UP): eth0: link is not ready

[Jan 01 00:00:17] radvd: version 1.8 started
[Jan 01 00:00:17] radvd: Warning: AdvRDNSSLifetime <= 2*MaxRtrAdvInterval would allow stale DNS servers to be deleted faster
[Jan 01 00:00:17] radvd: no linklocal address configured for br0
[   18.091000] device eth1 entered promiscuous mode

[   18.121000] ADDRCONF(NETDEV_UP): eth1: link is not ready

[   18.469000] device eth2 entered promiscuous mode

[   18.499000] ADDRCONF(NETDEV_UP): eth2: link is not ready

[   18.859000] device eth3 entered promiscuous mode

[   18.888000] ADDRCONF(NETDEV_UP): eth3: link is not ready

[   19.210000] *** dslThread dslPid=970

[   19.213000] BcmAdsl_Initialize=0xC0236BF0, g_pFnNotifyCallback=0xC0262EA0

[   19.371000] pSdramPHY=0xA7FFFFF8, 0x15B790 0xDEADBEEF

[   19.376000] *** XfaceOffset: 0x21F90 => 0x21F90 ***

[   19.720000] *** PhySdramSize got adjusted: 0x90870 => 0xA693C ***

[   19.725000] AdslCoreSharedMemInit: shareMemSize=366237(366240)

[   19.738000] AdslCoreHwReset:  pLocSbSta=84de0000 bkupThreshold=1600

[   19.744000] AdslCoreHwReset:  AdslOemDataAddr = 0xA7F8526C

[   19.750000] DSL driver initialisation skyGetADSLRouterOEMSerialNumber returns [SR101 3.50.2116.R]

[   19.759000] ***BcmDiagsMgrRegisterClient: 0 ***

[   19.764000] dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered 

[   19.771000] fapDrv_psmAlloc: fapIdx=0, size: 1600, offset=b1012be0 bytes remaining 584

[   19.779000] XTM Init: 200 rx BDs at 0xb1012be0

[   19.783000] fapDrv_psmAlloc: fapIdx=0, size: 128, offset=b1013220 bytes remaining 456

[   19.791000] XTM Init: 16 rx BDs at 0xb1013220

ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
RTNETLINK answers: No such process
RTNETLINK answers: No such file or directory
RTNETLINK answers: File exists
RTNETLINK answers: File exists
device wl0 is not a slave of br0
[   21.203000] device wl0 entered promiscuous mode

[   21.268000] br0: port 5(wl0) entered forwarding state

[   21.272000] br0: port 5(wl0) entered forwarding state

[   21.280000] ADDRCONF(NETDEV_CHANGE): br0: link becomes ready

[   21.430000] monitor task is initialized pid= 382 


starting pid 1104, tty '': '-/bin/sh -l -c consoled'

WAN mode: AUTO ADSL/Ethenet Discovery
RTNETLINK answers: No such process
RTNETLINK answers: No such file or directory
RTNETLINK answers: File exists
RTNETLINK answers: File exists
STATRTING Device Monitor 
BCM96362 Broadband Router
tr143EchoCfgServer:error:23.866:setupConfig:162:failed to get lock, ret=9809
tr143EchoCfgServer:error:23.866:main:410:setupConfig error ret=-1
Setting SO_REUSEADDR...OK.
 MUlticase Member ship added 
devicemonitor:error:23.978:main:850:Message type 10000250 received
devicemonitor:error:23.979:main:850:Message type 100007c0 received
devicemonitor:error:23.980:main:850:Message type 100007c0 received
devicemonitor:error:23.980:main:850:Message type 100007c0 received
devicemonitor:error:23.980:main:850:Message type 100007c0 received
WLmngr Daemon is running
wlevt is ready for new msg...
fus:error:24.296:getDeviceInfo:1392:Model Name ===[SR101-16]
fus:error:24.298:main:843:=========== FUS started ==============
fus:error:24.298:main:857:====>>> FUS action changed from 'Undefined' to 'FUS_ACTION_EXIT'
1097:error:24.852:main:1242:FUS is exiting
tr69c:error:25.202:updateTr69cCfgInfo_igd:1028:could not build full path to (null)
tr69c:error:25.203:oalTms_parseXSIDateTime:37:Invalid input arguments. Exit oalTms_parseXSIDateTime
tr69c:error:25.203:updateTr69cCfgInfo_igd:1127:Invalid periodic Timebase in datamodel
killall: hspotap: no process killed
killall: bsd: no process killed
[   27.958000] br0: port 5(wl0) entered disabled state

acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x100b
wlmngr:error:32.295:wlmngr_startWsc:1265: WPS##########	 Setting wps_device_pin to 83409509
[   33.440000] br0: port 5(wl0) entered forwarding state

[   33.445000] br0: port 5(wl0) entered forwarding state

[Jan 01 00:00:33] radvd: interface br0 seems to have come back up, trying to reinitialize
[Jan 01 00:00:33] radvd: attempting to reread config file
[Jan 01 00:00:33] radvd: Warning: AdvRDNSSLifetime <= 2*MaxRtrAdvInterval would allow stale DNS servers to be deleted faster
[Jan 01 00:00:33] radvd: resuming normal operation
[Jan 01 00:00:33] radvd: Unable to open prefix conf file. error: No such file or directory
[Jan 01 00:00:33] radvd: Failed to get updated prefix info details
[Jan 01 00:00:33] radvd: received RA from fe80::7e4c:a5ff:fe85:1d60
Setting SSID: <redacted>
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
[   34.212000] br0: port 5(wl0) entered disabled state

[   34.238000] device wl0 left promiscuous mode

[   34.242000] br0: port 5(wl0) entered disabled state

[   34.423000] device wl0 entered promiscuous mode

[   34.455000] br0: port 5(wl0) entered forwarding state

[   34.459000] br0: port 5(wl0) entered forwarding state

[Jan 01 00:00:49] radvd: received RA from fe80::7e4c:a5ff:fe85:1d60
[Jan 01 00:01:05] radvd: received RA from fe80::7e4c:a5ff:fe85:1d60
[Jan 01 00:01:21] radvd: received RA from fe80::7e4c:a5ff:fe85:1d60
[Jan 01 00:05:29] radvd: received RA from fe80::7e4c:a5ff:fe85:1d60