Skip to content

Instantly share code, notes, and snippets.

@svanheule

svanheule/dmesg-ath10-ct-5.8.log Secret

Last active August 27, 2020 12:41
Show Gist options
  • Star 0 You must be signed in to star a gist
  • Fork 0 You must be signed in to fork a gist
  • Save svanheule/33f43e2495581db7910e43682649f0b8 to your computer and use it in GitHub Desktop.
Save svanheule/33f43e2495581db7910e43682649f0b8 to your computer and use it in GitHub Desktop.
Download ZIP
qca9982 features
Raw
dmesg-ath10-ct-5.8.log
[ 35.352140] ath10k 5.7 driver, optimized for CT firmware, probing pci device: 0x40.
[ 35.374021] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 35.380810] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 37.520730] ath10k_pci 0000:00:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 37.530302] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 37.549100] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9980-fH-13-10af6a005 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,htt-mgt-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 44ae70f7
[ 37.639729] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 38.797650] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 38.805430] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
[ 38.881266] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 38.892580] ath10k_pci 0000:00:00.0: wmi print 'free: 31080 iram: 23332 sram: 9596'
[ 39.041368] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 39.225997] ath: EEPROM regdomain sanitized
[ 39.226007] ath: EEPROM regdomain: 0x64
[ 39.226011] ath: EEPROM indicates we should expect a direct regpair map
[ 39.226030] ath: Country alpha2 being used: 00
[ 39.226033] ath: Regpair used: 0x64
[ 39.299697] ath: EEPROM regdomain sanitized
[ 39.299707] ath: EEPROM regdomain: 0x64
[ 39.299711] ath: EEPROM indicates we should expect a direct regpair map
[ 39.299730] ath: Country alpha2 being used: 00
[ 39.299733] ath: Regpair used: 0x64
[ 55.830359] ath: EEPROM regdomain: 0x8038
[ 55.834553] ath: EEPROM indicates we should expect a country code
[ 55.840859] ath: doing EEPROM country->regdmn map search
[ 55.846354] ath: country maps to regdmn code: 0x37
[ 55.851308] ath: Country alpha2 being used: BE
[ 55.855903] ath: Regpair used: 0x37
[ 55.859517] ath: regdomain 0x8038 dynamically updated by user
[ 55.865527] ath: EEPROM regdomain: 0x8038
[ 55.869684] ath: EEPROM indicates we should expect a country code
[ 55.875982] ath: doing EEPROM country->regdmn map search
[ 55.881476] ath: country maps to regdmn code: 0x37
[ 55.886430] ath: Country alpha2 being used: BE
[ 55.891027] ath: Regpair used: 0x37
[ 55.894635] ath: regdomain 0x8038 dynamically updated by user
[ 60.754847] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 60.762660] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
[ 60.838358] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 60.852990] ath10k_pci 0000:00:00.0: wmi print 'free: 31080 iram: 23332 sram: 9596'
[ 61.245640] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 61.323030] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 123.917862] ath10k_pci 0000:00:00.0: mac flush null vif, drop 0 queues 0xffff
[ 124.186857] ath10k_pci 0000:00:00.0: failed to pull fw stats: -71
Raw
dmesg-ath10-ct.log
# dmesg | grep ath
[ 35.487918] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x40.
[ 35.495997] ath10k_mac_create, priv_size: 804 hw: (ptrval) hw->priv: (ptrval)
[ 35.525543] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 35.532321] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 37.662952] ath10k_pci 0000:00:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 37.672527] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 37.691307] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9980-fH-13-10af6a005 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,htt-mgt-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 44ae70f7
[ 37.782009] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 38.972946] ath10k_pci 0000:00:00.0: unsupported HTC service id: 1536
[ 38.983963] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 38.991754] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
[ 39.067577] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 39.078897] ath10k_pci 0000:00:00.0: wmi print 'free: 31080 iram: 23332 sram: 9596'
[ 39.339767] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1
[ 39.425930] ath: EEPROM regdomain sanitized
[ 39.425941] ath: EEPROM regdomain: 0x64
[ 39.425944] ath: EEPROM indicates we should expect a direct regpair map
[ 39.425962] ath: Country alpha2 being used: 00
[ 39.425965] ath: Regpair used: 0x64
[ 39.499657] ath: EEPROM regdomain sanitized
[ 39.499667] ath: EEPROM regdomain: 0x64
[ 39.499671] ath: EEPROM indicates we should expect a direct regpair map
[ 39.499690] ath: Country alpha2 being used: 00
[ 39.499693] ath: Regpair used: 0x64
[ 55.923672] ath: EEPROM regdomain: 0x8038
[ 55.927864] ath: EEPROM indicates we should expect a country code
[ 55.934172] ath: doing EEPROM country->regdmn map search
[ 55.939665] ath: country maps to regdmn code: 0x37
[ 55.944620] ath: Country alpha2 being used: BE
[ 55.949214] ath: Regpair used: 0x37
[ 55.952817] ath: regdomain 0x8038 dynamically updated by user
[ 55.958829] ath: EEPROM regdomain: 0x8038
[ 55.962985] ath: EEPROM indicates we should expect a country code
[ 55.969286] ath: doing EEPROM country->regdmn map search
[ 55.974777] ath: country maps to regdmn code: 0x37
[ 55.979731] ath: Country alpha2 being used: BE
[ 55.984328] ath: Regpair used: 0x37
[ 55.987940] ath: regdomain 0x8038 dynamically updated by user
[ 59.486793] ath10k_pci 0000:00:00.0: unsupported HTC service id: 1536
[ 59.493992] ath10k_pci 0000:00:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96
[ 59.501784] ath10k_pci 0000:00:00.0: msdu-desc: 2500 skid: 32
[ 59.577608] ath10k_pci 0000:00:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'
[ 59.588934] ath10k_pci 0000:00:00.0: wmi print 'free: 31080 iram: 23332 sram: 9596'
[ 59.937463] ath10k_pci 0000:00:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4
[ 60.126892] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 121.869954] ath10k_pci 0000:00:00.0: mac flush null vif, drop 0 queues 0xffff
[ 122.135823] ath10k_pci 0000:00:00.0: failed to pull fw stats: -71
Raw
dmesg-ath10k.log
# dmesg | grep ath
[ 35.657886] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 35.664672] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 37.742777] ath10k_pci 0000:00:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
[ 37.752344] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 37.769622] ath10k_pci 0000:00:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
[ 37.852100] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
[ 39.115853] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
[ 39.193917] ath: EEPROM regdomain sanitized
[ 39.193927] ath: EEPROM regdomain: 0x64
[ 39.193931] ath: EEPROM indicates we should expect a direct regpair map
[ 39.193949] ath: Country alpha2 being used: 00
[ 39.193951] ath: Regpair used: 0x64
[ 39.271623] ath: EEPROM regdomain sanitized
[ 39.271634] ath: EEPROM regdomain: 0x64
[ 39.271637] ath: EEPROM indicates we should expect a direct regpair map
[ 39.271656] ath: Country alpha2 being used: 00
[ 39.271659] ath: Regpair used: 0x64
[ 55.698268] ath: EEPROM regdomain: 0x8038
[ 55.702460] ath: EEPROM indicates we should expect a country code
[ 55.708763] ath: doing EEPROM country->regdmn map search
[ 55.714257] ath: country maps to regdmn code: 0x37
[ 55.719211] ath: Country alpha2 being used: BE
[ 55.723806] ath: Regpair used: 0x37
[ 55.727419] ath: regdomain 0x8038 dynamically updated by user
[ 55.733428] ath: EEPROM regdomain: 0x8038
[ 55.737586] ath: EEPROM indicates we should expect a country code
[ 55.743885] ath: doing EEPROM country->regdmn map search
[ 55.749378] ath: country maps to regdmn code: 0x37
[ 55.754332] ath: Country alpha2 being used: BE
[ 55.758929] ath: Regpair used: 0x37
[ 55.762541] ath: regdomain 0x8038 dynamically updated by user
Raw
iw-ath10-ct
Wiphy phy0
max # scan SSIDs: 16
max scan IEs length: 199 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* P2P-device
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
VHT Capabilities (0x339a79b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (20.0 dBm) (radar detection)
* 5280 MHz [56] (20.0 dBm) (radar detection)
* 5300 MHz [60] (20.0 dBm) (radar detection)
* 5320 MHz [64] (20.0 dBm) (radar detection)
* 5500 MHz [100] (26.0 dBm) (radar detection)
* 5520 MHz [104] (26.0 dBm) (radar detection)
* 5540 MHz [108] (26.0 dBm) (radar detection)
* 5560 MHz [112] (26.0 dBm) (radar detection)
* 5580 MHz [116] (26.0 dBm) (radar detection)
* 5600 MHz [120] (26.0 dBm) (radar detection)
* 5620 MHz [124] (26.0 dBm) (radar detection)
* 5640 MHz [128] (26.0 dBm) (radar detection)
* 5660 MHz [132] (26.0 dBm) (radar detection)
* 5680 MHz [136] (26.0 dBm) (radar detection)
* 5700 MHz [140] (26.0 dBm) (radar detection)
* 5720 MHz [144] (disabled)
* 5745 MHz [149] (13.0 dBm)
* 5765 MHz [153] (13.0 dBm)
* 5785 MHz [157] (13.0 dBm)
* 5805 MHz [161] (13.0 dBm)
* 5825 MHz [165] (13.0 dBm)
* 5845 MHz [169] (13.0 dBm)
* 5865 MHz [173] (13.0 dBm)
valid interface combinations:
* #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
Raw
iw-ath10k
Wiphy phy0
max # scan SSIDs: 16
max scan IEs length: 199 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* managed
* AP
* monitor
* mesh point
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
VHT Capabilities (0x339a79b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (20.0 dBm) (radar detection)
* 5280 MHz [56] (20.0 dBm) (radar detection)
* 5300 MHz [60] (20.0 dBm) (radar detection)
* 5320 MHz [64] (20.0 dBm) (radar detection)
* 5500 MHz [100] (26.0 dBm) (radar detection)
* 5520 MHz [104] (26.0 dBm) (radar detection)
* 5540 MHz [108] (26.0 dBm) (radar detection)
* 5560 MHz [112] (26.0 dBm) (radar detection)
* 5580 MHz [116] (26.0 dBm) (radar detection)
* 5600 MHz [120] (26.0 dBm) (radar detection)
* 5620 MHz [124] (26.0 dBm) (radar detection)
* 5640 MHz [128] (26.0 dBm) (radar detection)
* 5660 MHz [132] (26.0 dBm) (radar detection)
* 5680 MHz [136] (26.0 dBm) (radar detection)
* 5700 MHz [140] (26.0 dBm) (radar detection)
* 5720 MHz [144] (disabled)
* 5745 MHz [149] (13.0 dBm)
* 5765 MHz [153] (13.0 dBm)
* 5785 MHz [157] (13.0 dBm)
* 5805 MHz [161] (13.0 dBm)
* 5825 MHz [165] (13.0 dBm)
* 5845 MHz [169] (13.0 dBm)
* 5865 MHz [173] (13.0 dBm)
valid interface combinations:
* #{ managed } <= 1, #{ AP, mesh point } <= 16,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
Raw
iw-phy0-info.patch
--- iw-phy0-info.txt 2020-08-27 09:42:03.029563124 +0200
+++ iw-phy0-info-ct.txt 2020-08-27 09:28:24.744466491 +0200
@@ -1,10 +1,4 @@
-[ 35.657886] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
-[ 35.664672] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
-[ 37.742777] ath10k_pci 0000:00:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003b01ff sub 168c:0002
-[ 37.752344] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
-[ 37.769622] ath10k_pci 0000:00:00.0: firmware ver 10.4.1.00030-1 api 5 features no-p2p crc32 d2901e01
-[ 37.852100] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2
-[ 39.115853] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 512 raw 0 hwcrypto 1
+[ 37.387211] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9980-fH-13-10af6a005 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,htt-mgt-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 44ae70f7
Wiphy phy0
max # scan SSIDs: 16
@@ -21,10 +15,15 @@
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
+ * IBSS
* managed
* AP
+ * AP/VLAN
* monitor
* mesh point
+ * P2P-client
+ * P2P-GO
+ * P2P-device
Band 2:
Capabilities: 0x19ef
RX LDPC
@@ -100,7 +99,7 @@
* 5845 MHz [169] (13.0 dBm)
* 5865 MHz [173] (13.0 dBm)
valid interface combinations:
- * #{ managed } <= 1, #{ AP, mesh point } <= 16,
+ * #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
Raw
lspci
# lspci -nnvvk
00:00.0 Network controller [0280]: Qualcomm Atheros QCA9980/9990 802.11ac Wireless Network Adapter [168c:0040]
Subsystem: Qualcomm Atheros Device [168c:0002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 14
Region 0: Memory at 12000000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/32 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM not supported
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Not Supported, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCap2: Supported Link Speeds: 2.5-5GT/s, Crosslink- Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [148 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [158 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [160 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- L1_PM_Substates-
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
L1SubCtl2:
Kernel driver in use: ath10k_pci
lspci: Unable to load libkmod resources: error -12
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment