/config_rover_gears.ini
Created Aug 12, 2018
This pretty much the config file I use for Rover's gears. I am always changing things, so this represents one state in time. Hopefully it serves as a starting point.
| # generated by Slic3r 1.2.9 on Sun Aug 12 17:25:09 2018 | |
| avoid_crossing_perimeters = 1 | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| bed_temperature = 80 | |
| before_layer_gcode = | |
| bottom_solid_layers = 0 | |
| bridge_acceleration = 0 | |
| bridge_fan_speed = 83 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 10 | |
| brim_width = 0 | |
| complete_objects = 0 | |
| cooling = 1 | |
| default_acceleration = 0 | |
| disable_fan_first_layers = 1 | |
| dont_support_bridges = 1 | |
| duplicate_distance = 6 | |
| end_gcode = G91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 X-20 Y-20 F4800 ;move Z up a bit and retract filament even more\nG1 X10 Y180 F3000 ; Feed the bed forward making removal easy.\nM84 ;steppers off\nM104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG90 ;absolute positioning\n | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 20 | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extruder_offset = 0x0 | |
| extrusion_axis = E | |
| extrusion_multiplier = 0.86 | |
| extrusion_width = 1.2 | |
| fan_always_on = 1 | |
| fan_below_layer_time = 60 | |
| filament_colour = #393BF7 | |
| filament_diameter = 1.74 | |
| fill_angle = 45 | |
| fill_density = 50% | |
| fill_pattern = rectilinear | |
| first_layer_acceleration = 0 | |
| first_layer_bed_temperature = 80 | |
| first_layer_extrusion_width = 0 | |
| first_layer_height = 0.6 | |
| first_layer_speed = 50% | |
| first_layer_temperature = 205 | |
| gap_fill_speed = 20 | |
| gcode_arcs = 0 | |
| gcode_comments = 0 | |
| gcode_flavor = reprap | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 55% | |
| infill_speed = 20 | |
| interface_shells = 0 | |
| layer_gcode = | |
| layer_height = 0.2 | |
| max_fan_speed = 100 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_fan_speed = 88 | |
| min_print_speed = 2 | |
| min_skirt_length = 0 | |
| notes = | |
| nozzle_diameter = 1.2 | |
| octoprint_apikey = | |
| octoprint_host = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 20 | |
| perimeters = 2 | |
| post_process = | |
| pressure_advance = 0 | |
| raft_layers = 0 | |
| resolution = 0 | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 1.2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| seam_position = nearest | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 0 | |
| slowdown_below_layer_time = 5 | |
| small_perimeter_speed = 10 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 10 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| start_gcode = M140 S80; Set bed to start heating and continue\nM104 S205 ; heat nozzle\nM190 S80 ;heat bed\nG21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F100 ;move the platform down 15mm\nG92 E0 ;zero the extruded length\nG1 F200 E3 ;extrude 3mm of feed stock\nG92 E0 ;zero the extruded length again\nG1 F90\n;Put printing message on LCD screen\nM117 Printing... | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 10 | |
| support_material_threshold = 60 | |
| temperature = 205 | |
| thin_walls = 1 | |
| threads = 2 | |
| toolchange_gcode = | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 80 | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| xy_size_compensation = 0 | |
| z_offset = 0 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment