Created
September 10, 2012 06:50
-
-
Save tomari/3689297 to your computer and use it in GitHub Desktop.
Four-DIMM PowerMac G5 (PowerMac7,3)
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| processor : 0 | |
| cpu : PPC970, altivec supported | |
| clock : 1800.000000MHz | |
| revision : 2.2 (pvr 0039 0202) | |
| processor : 1 | |
| cpu : PPC970, altivec supported | |
| clock : 1800.000000MHz | |
| revision : 2.2 (pvr 0039 0202) | |
| timebase : 33333333 | |
| platform : PowerMac | |
| model : PowerMac7,3 | |
| machine : PowerMac7,3 | |
| motherboard : PowerMac7,3 MacRISC4 Power Macintosh | |
| detected as : 336 (PowerMac G5) | |
| pmac flags : 00000000 | |
| L2 cache : 512K unified | |
| pmac-generation : NewWorld | |
| 0000:f0:0b.0 Host bridge: Apple Computer Inc. U3 AGP | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- | |
| Latency: 16, Cache Line Size: 32 bytes | |
| Capabilities: [80] AGP version 3.0 | |
| Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans+ 64bit+ FW+ AGP3+ Rate=x4,x8 | |
| Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit+ FW- Rate=<none> | |
| Kernel driver in use: agpgart-uninorth | |
| 0000:f0:10.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200 Ultra] (rev a1) (prog-if 00 [VGA controller]) | |
| Subsystem: nVidia Corporation Device 0010 | |
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 16 (1250ns min, 250ns max) | |
| Interrupt: pin A routed to IRQ 48 | |
| Region 0: Memory at 91000000 (32-bit, non-prefetchable) [size=16M] | |
| Region 1: Memory at 98000000 (32-bit, prefetchable) [size=128M] | |
| Expansion ROM at 90000000 [disabled] [size=128K] | |
| Capabilities: [60] Power Management version 2 | |
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) | |
| Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- | |
| Capabilities: [44] AGP version 3.0 | |
| Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 | |
| Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> | |
| Kernel driver in use: nvidiafb | |
| 0001:00:00.0 Host bridge: Apple Computer Inc. CPC945 HT Bridge | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 0 | |
| Capabilities: [40] HyperTransport: Host or Secondary Interface | |
| Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide- Slave- <EOCErr- DUL- | |
| Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- | |
| Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- | |
| Revision ID: 1.04 | |
| Link Frequency: 400MHz | |
| Link Error: <Prot- <Ovfl- <EOC- CTLTm- | |
| Link Frequency Capability: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- | |
| Feature Capability: IsocFC- LDTSTOP+ CRCTM+ ECTLT- 64bA- UIDRD- ExtRS+ UCnfE- | |
| Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- | |
| Prefetchable memory behind bridge Upper: 00-00 | |
| 0001:00:01.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge (prog-if 00 [Normal decode]) | |
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 0, Cache Line Size: 64 bytes | |
| Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 | |
| I/O behind bridge: 0000f000-00000fff | |
| Memory behind bridge: 80000000-800fffff | |
| Prefetchable memory behind bridge: 00000000-000fffff | |
| Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- | |
| BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- | |
| PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- | |
| Capabilities: [70] HyperTransport: Slave or Primary Interface | |
| Command: BaseUnitID=1 UnitCnt=5 MastHost- DefDir- DUL- | |
| Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- | |
| Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- | |
| Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- | |
| Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- | |
| Revision ID: 1.04 | |
| Link Frequency 0: 400MHz | |
| Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- | |
| Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- | |
| Feature Capability: IsocFC- LDTSTOP+ CRCTM+ ECTLT- 64bA- UIDRD- | |
| Link Frequency 1: 200MHz | |
| Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- | |
| Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- | |
| Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- | |
| Prefetchable memory behind bridge Upper: 00-00 | |
| Bus Number: 00 | |
| Capabilities: [90] HyperTransport: Interrupt Discovery and Configuration | |
| 0001:00:02.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge (prog-if 00 [Normal decode]) | |
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 0, Cache Line Size: 64 bytes | |
| Bus: primary=00, secondary=05, subordinate=05, sec-latency=32 | |
| I/O behind bridge: 0000f000-00000fff | |
| Memory behind bridge: 80700000-807fffff | |
| Prefetchable memory behind bridge: 00000000-000fffff | |
| Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- | |
| BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- | |
| PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- | |
| Capabilities: [70] HyperTransport: Revision ID: 1.04 | |
| 0001:00:03.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge (prog-if 00 [Normal decode]) | |
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 0, Cache Line Size: 64 bytes | |
| Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 | |
| I/O behind bridge: 0000f000-00000fff | |
| Memory behind bridge: 80100000-801fffff | |
| Prefetchable memory behind bridge: 00000000-000fffff | |
| Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- | |
| BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- | |
| PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- | |
| Capabilities: [70] HyperTransport: Revision ID: 1.04 | |
| 0001:00:04.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge (prog-if 00 [Normal decode]) | |
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 0, Cache Line Size: 64 bytes | |
| Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 | |
| I/O behind bridge: 0000f000-00000fff | |
| Memory behind bridge: 80200000-805fffff | |
| Prefetchable memory behind bridge: 00000000-000fffff | |
| Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- | |
| BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- | |
| PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- | |
| Capabilities: [70] HyperTransport: Revision ID: 1.04 | |
| 0001:00:05.0 PCI bridge: Apple Computer Inc. K2 HT-PCI Bridge (prog-if 00 [Normal decode]) | |
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 0, Cache Line Size: 64 bytes | |
| Bus: primary=00, secondary=04, subordinate=04, sec-latency=32 | |
| I/O behind bridge: 0000f000-00000fff | |
| Memory behind bridge: 80600000-806fffff | |
| Prefetchable memory behind bridge: 00000000-000fffff | |
| Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- | |
| BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- | |
| PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- | |
| Capabilities: [70] HyperTransport: Revision ID: 1.04 | |
| 0001:01:07.0 Unassigned class [ff00]: Apple Computer Inc. K2 KeyLargo Mac/IO (rev 60) | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 16, Cache Line Size: 64 bytes | |
| Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K] | |
| Kernel driver in use: macio | |
| 0001:01:08.0 USB controller: Apple Computer Inc. K2 KeyLargo USB (prog-if 10 [OHCI]) | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 16 (750ns min, 21500ns max), Cache Line Size: 64 bytes | |
| Interrupt: pin A routed to IRQ 27 | |
| Region 0: Memory at 80081000 (32-bit, non-prefetchable) [size=4K] | |
| Kernel driver in use: ohci_hcd | |
| 0001:01:09.0 USB controller: Apple Computer Inc. K2 KeyLargo USB (prog-if 10 [OHCI]) | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 16 (750ns min, 21500ns max), Cache Line Size: 64 bytes | |
| Interrupt: pin A routed to IRQ 28 | |
| Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=4K] | |
| Kernel driver in use: ohci_hcd | |
| 0001:02:0d.0 Unassigned class [ff00]: Apple Computer Inc. K2 ATA/100 | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 32, Cache Line Size: 32 bytes | |
| Interrupt: pin ? routed to IRQ 39 | |
| Region 0: Memory at 80104000 (32-bit, non-prefetchable) [size=16K] | |
| Kernel driver in use: ide-pmac | |
| 0001:02:0e.0 FireWire (IEEE 1394): Apple Computer Inc. K2 FireWire (prog-if 10 [OHCI]) | |
| Subsystem: Apple Computer Inc. Device 5811 | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 248 (3000ns min, 6000ns max), Cache Line Size: 64 bytes | |
| Interrupt: pin A routed to IRQ 40 | |
| Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=4K] | |
| Capabilities: [44] Power Management version 2 | |
| Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) | |
| Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ | |
| Kernel driver in use: firewire_ohci | |
| 0001:03:0f.0 Ethernet controller: Apple Computer Inc. K2 GMAC (Sun GEM) | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx- | |
| Latency: 16 (16000ns min, 16000ns max), Cache Line Size: 64 bytes | |
| Interrupt: pin A routed to IRQ 41 | |
| Region 0: Memory at 80400000 (32-bit, non-prefetchable) [size=2M] | |
| Expansion ROM at 80200000 [disabled] [size=1M] | |
| Kernel driver in use: gem | |
| 0001:04:0c.0 IDE interface: Broadcom K2 SATA (prog-if 8f [Master SecP SecO PriP PriO]) | |
| Subsystem: Broadcom K2 SATA | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 16 | |
| Interrupt: pin ? routed to IRQ 16 | |
| Region 0: I/O ports at <unassigned> [disabled] | |
| Region 1: I/O ports at <unassigned> [disabled] | |
| Region 2: I/O ports at <unassigned> [disabled] | |
| Region 3: I/O ports at <unassigned> [disabled] | |
| Region 4: I/O ports at <unassigned> [disabled] | |
| Region 5: Memory at 80600000 (32-bit, non-prefetchable) [size=8K] | |
| Kernel driver in use: sata_svw | |
| 0001:05:0b.0 USB controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI]) | |
| Subsystem: NEC Corporation Hama USB 2.0 CardBus | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes | |
| Interrupt: pin A routed to IRQ 63 | |
| Region 0: Memory at 80702000 (32-bit, non-prefetchable) [size=4K] | |
| Capabilities: [40] Power Management version 2 | |
| Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) | |
| Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- | |
| Kernel driver in use: ohci_hcd | |
| 0001:05:0b.1 USB controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI]) | |
| Subsystem: NEC Corporation Hama USB 2.0 CardBus | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes | |
| Interrupt: pin B routed to IRQ 63 | |
| Region 0: Memory at 80701000 (32-bit, non-prefetchable) [size=4K] | |
| Capabilities: [40] Power Management version 2 | |
| Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) | |
| Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- | |
| Kernel driver in use: ohci_hcd | |
| 0001:05:0b.2 USB controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI]) | |
| Subsystem: NEC Corporation USB 2.0 | |
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- | |
| Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- | |
| Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 64 bytes | |
| Interrupt: pin C routed to IRQ 63 | |
| Region 0: Memory at 80700000 (32-bit, non-prefetchable) [size=256] | |
| Capabilities: [40] Power Management version 2 | |
| Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) | |
| Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- | |
| Kernel driver in use: ehci_hcd | |
| Allocated 4096 bytes for 4 pacas at c00000000ffff000 | |
| DART table allocated at: c00000007f000000 | |
| Using PowerMac machine description | |
| Page orders: linear mapping = 24, virtual = 12, io = 12 | |
| Found U3 memory controller & host bridge @ 0xf8000000 revision: 0xb3 | |
| Mapped at 0xd000080080000000 | |
| Found a K2 mac-io controller, rev: 96, mapped at 0xd000080080041000 | |
| PowerMac motherboard: PowerMac G5 | |
| DART IOMMU initialized for U3 type chipset | |
| bootconsole [udbg0] enabled | |
| CPU maps initialized for 1 thread per core | |
| (thread shift is 0) | |
| Starting Linux PPC64 #1 SMP Mon Sep 10 14:50:50 IRKT 2012 | |
| ----------------------------------------------------- | |
| ppc64_pft_size = 0x0 | |
| physicalMemorySize = 0x100000000 | |
| htab_address = 0xc00000017c000000 | |
| htab_hash_mask = 0x7ffff | |
| ----------------------------------------------------- | |
| Linux version 3.4.9-gentoo (root@acapulco) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #1 SMP Mon Sep 10 14:50:50 IRKT 2012 | |
| [boot]0012 Setup Arch | |
| Found U3-AGP PCI host bridge. Firmware bus number: 240->255 | |
| PCI host bridge /pci@0,f0000000 ranges: | |
| MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 | |
| IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000 | |
| MEM 0x0000000090000000..0x000000009fffffff -> 0x0000000090000000 | |
| Can't get bus-range for /ht@0,f2000000, assume bus 0 | |
| Found U3-HT PCI host bridge. Firmware bus number: 0->239 | |
| PCI host bridge /ht@0,f2000000 (primary) ranges: | |
| via-pmu: Server Mode is disabled | |
| PMU driver v2 initialized for Core99, firmware: 0c | |
| nvram: Checking bank 0... | |
| nvram: gen0=996, gen1=997 | |
| nvram: Active bank is: 1 | |
| nvram: OF partition at 0x410 | |
| nvram: XP partition at 0x1020 | |
| nvram: NR partition at 0x1120 | |
| Top of RAM: 0x180000000, Total RAM: 0x100000000 | |
| Memory hole size: 2048MB | |
| Zone PFN ranges: | |
| DMA 0x00000000 -> 0x00180000 | |
| Normal empty | |
| Movable zone start PFN for each node | |
| Early memory PFN ranges | |
| 0: 0x00000000 -> 0x00080000 | |
| 0: 0x00100000 -> 0x00180000 | |
| On node 0 totalpages: 1048576 | |
| free_area_init_node: node 0, pgdat c00000000088c300, node_mem_map c000000000cbb000 | |
| DMA zone: 21504 pages used for memmap | |
| DMA zone: 0 pages reserved | |
| DMA zone: 1027072 pages, LIFO batch:31 | |
| [boot]0015 Setup Done | |
| PERCPU: Embedded 11 pages/cpu @c000000006100000 s15616 r0 d29440 u524288 | |
| pcpu-alloc: s15616 r0 d29440 u524288 alloc=1*1048576 | |
| pcpu-alloc: [0] 0 1 | |
| Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1027072 | |
| Kernel command line: root=/dev/sda4 ro | |
| PID hash table entries: 4096 (order: 3, 32768 bytes) | |
| Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) | |
| Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) | |
| Memory: 4009272k/4194304k available (8716k kernel code, 2282184k reserved, 1172k data, 500k bss, 300k init) | |
| SLUB: Genslabs=15, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 | |
| Hierarchical RCU implementation. | |
| NR_IRQS:512 nr_irqs:512 16 | |
| mpic: Resetting | |
| mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 2 CPUs | |
| mpic: ISU size: 120, shift: 7, mask: 7f | |
| mpic: Initializing for 120 sources | |
| mpic: Resetting | |
| mpic: Setting up MPIC " MPIC 2 " version 1.2 at f8040000, max 2 CPUs | |
| mpic: ISU size: 120, shift: 7, mask: 7f | |
| mpic: Initializing for 120 sources | |
| /u3@0,f8000000/mpic@f8040000: hooking up to IRQ 56 | |
| time_init: decrementer frequency = 33.333333 MHz | |
| time_init: processor frequency = 1800.000000 MHz | |
| clocksource: timebase mult[1e000005] shift[24] registered | |
| clockevent: decrementer mult[8888887] shift[32] cpu[0] | |
| Console: colour dummy device 80x25 | |
| console [tty0] enabled, bootconsole disabled | |
| pid_max: default: 32768 minimum: 301 | |
| Mount-cache hash table entries: 256 | |
| PowerMac SMP probe found 2 cpus | |
| KeyWest i2c @0xf8001003 irq 42 /u3@0,f8000000/i2c@f8001000 | |
| channel 0 bus <multibus> | |
| channel 1 bus <multibus> | |
| KeyWest i2c @0x80018000 irq 26 /ht@0,f2000000/pci@1/mac-io@7/i2c@18000 | |
| channel 0 bus <multibus> | |
| PMU i2c /ht@0,f2000000/pci@1/mac-io@7/via-pmu@16000/pmu-i2c | |
| channel 1 bus <multibus> | |
| channel 2 bus <multibus> | |
| Processor timebase sync using Cypress i2c clock | |
| mpic: requesting IPIs... | |
| PPC970/FX/MP performance monitor hardware support registered | |
| Brought up 2 CPUs | |
| NET: Registered protocol family 16 | |
| PCI: Probing PCI hardware | |
| PCI host bridge to bus 0000:f0 | |
| pci_bus 0000:f0: root bus resource [io 0x10000-0x80ffff] (bus address [0x0000-0x7fffff]) | |
| pci_bus 0000:f0: root bus resource [mem 0xf1000000-0xf1ffffff] | |
| pci_bus 0000:f0: root bus resource [mem 0x90000000-0x9fffffff] | |
| pci 0000:f0:0b.0: [106b:004b] type 00 class 0x060000 | |
| pci 0000:f0:10.0: [10de:0321] type 00 class 0x030000 | |
| pci 0000:f0:10.0: reg 10: [mem 0x91000000-0x91ffffff] | |
| pci 0000:f0:10.0: reg 14: [mem 0x98000000-0x9fffffff pref] | |
| pci 0000:f0:10.0: reg 30: [mem 0x90000000-0x9001ffff pref] | |
| IOMMU table initialized, virtual merging enabled | |
| PCI host bridge to bus 0001:00 | |
| pci_bus 0001:00: root bus resource [io 0x811000-0xc10fff] (bus address [0x0000-0x3fffff]) | |
| pci_bus 0001:00: root bus resource [mem 0xfa000000-0xffffffff] | |
| pci_bus 0001:00: root bus resource [mem 0x80000000-0x8fffffff] | |
| pci_bus 0001:00: root bus resource [mem 0xa0000000-0xefffffff] | |
| pci 0001:00:00.0: [106b:004a] type 00 class 0x060000 | |
| pci 0001:00:01.0: [106b:0045] type 01 class 0x060400 | |
| pci 0001:00:02.0: [106b:0046] type 01 class 0x060400 | |
| pci 0001:00:03.0: [106b:0047] type 01 class 0x060400 | |
| pci 0001:00:04.0: [106b:0048] type 01 class 0x060400 | |
| pci 0001:00:05.0: [106b:0049] type 01 class 0x060400 | |
| pci 0001:01:07.0: [106b:0041] type 00 class 0xff0000 | |
| pci 0001:01:07.0: reg 10: [mem 0x80000000-0x8007ffff] | |
| pci 0001:01:08.0: [106b:0040] type 00 class 0x0c0310 | |
| pci 0001:01:08.0: reg 10: [mem 0x80081000-0x80081fff] | |
| pci 0001:01:09.0: [106b:0040] type 00 class 0x0c0310 | |
| pci 0001:01:09.0: reg 10: [mem 0x80080000-0x80080fff] | |
| pci 0001:00:01.0: PCI bridge to [bus 01-01] | |
| pci 0001:00:01.0: bridge window [mem 0x80000000-0x800fffff] | |
| pci 0001:05:0b.0: [1033:0035] type 00 class 0x0c0310 | |
| pci 0001:05:0b.0: reg 10: [mem 0x80702000-0x80702fff] | |
| pci 0001:05:0b.0: supports D1 D2 | |
| pci 0001:05:0b.0: PME# supported from D0 D1 D2 D3hot D3cold | |
| pci 0001:05:0b.1: [1033:0035] type 00 class 0x0c0310 | |
| pci 0001:05:0b.1: reg 10: [mem 0x80701000-0x80701fff] | |
| pci 0001:05:0b.1: supports D1 D2 | |
| pci 0001:05:0b.1: PME# supported from D0 D1 D2 D3hot D3cold | |
| pci 0001:05:0b.2: [1033:00e0] type 00 class 0x0c0320 | |
| pci 0001:05:0b.2: reg 10: [mem 0x80700000-0x807000ff] | |
| pci 0001:05:0b.2: supports D1 D2 | |
| pci 0001:05:0b.2: PME# supported from D0 D1 D2 D3hot D3cold | |
| pci 0001:00:02.0: PCI bridge to [bus 05-05] | |
| pci 0001:00:02.0: bridge window [mem 0x80700000-0x807fffff] | |
| pci 0001:02:0d.0: [106b:0043] type 00 class 0xff0000 | |
| pci 0001:02:0d.0: reg 10: [mem 0x80104000-0x80107fff] | |
| pci 0001:02:0e.0: [106b:0042] type 00 class 0x0c0010 | |
| pci 0001:02:0e.0: reg 10: [mem 0x80100000-0x80100fff] | |
| pci 0001:02:0e.0: supports D1 D2 | |
| pci 0001:02:0e.0: PME# supported from D0 D1 D2 D3hot | |
| pci 0001:00:03.0: PCI bridge to [bus 02-02] | |
| pci 0001:00:03.0: bridge window [mem 0x80100000-0x801fffff] | |
| pci 0001:03:0f.0: [106b:004c] type 00 class 0x020000 | |
| pci 0001:03:0f.0: reg 10: [mem 0x80400000-0x805fffff] | |
| pci 0001:03:0f.0: reg 30: [mem 0x80200000-0x802fffff pref] | |
| pci 0001:00:04.0: PCI bridge to [bus 03-03] | |
| pci 0001:00:04.0: bridge window [mem 0x80200000-0x805fffff] | |
| pci 0001:04:0c.0: [1166:0240] type 00 class 0x01018f | |
| pci 0001:04:0c.0: reg 10: [io 0x811000-0x811007] | |
| pci 0001:04:0c.0: reg 14: [io 0x811000-0x811003] | |
| pci 0001:04:0c.0: reg 18: [io 0x811000-0x811007] | |
| pci 0001:04:0c.0: reg 1c: [io 0x811000-0x811003] | |
| pci 0001:04:0c.0: reg 20: [io 0x811000-0x81100f] | |
| pci 0001:04:0c.0: reg 24: [mem 0x80600000-0x80601fff] | |
| pci 0001:00:05.0: PCI bridge to [bus 04-04] | |
| pci 0001:00:05.0: bridge window [mem 0x80600000-0x806fffff] | |
| pci 0001:00:01.0: PCI bridge to [bus 01-01] | |
| pci 0001:00:01.0: bridge window [mem 0x80000000-0x800fffff] | |
| pci 0001:00:02.0: PCI bridge to [bus 05-05] | |
| pci 0001:00:02.0: bridge window [mem 0x80700000-0x807fffff] | |
| pci 0001:00:03.0: PCI bridge to [bus 02-02] | |
| pci 0001:00:03.0: bridge window [mem 0x80100000-0x801fffff] | |
| pci 0001:00:04.0: PCI bridge to [bus 03-03] | |
| pci 0001:00:04.0: bridge window [mem 0x80200000-0x805fffff] | |
| pci 0001:00:05.0: PCI bridge to [bus 04-04] | |
| pci 0001:00:05.0: bridge window [mem 0x80600000-0x806fffff] | |
| pci_bus 0000:f0: resource 4 [io 0x10000-0x80ffff] | |
| pci_bus 0000:f0: resource 5 [mem 0xf1000000-0xf1ffffff] | |
| pci_bus 0000:f0: resource 6 [mem 0x90000000-0x9fffffff] | |
| pci_bus 0001:00: resource 4 [io 0x811000-0xc10fff] | |
| pci_bus 0001:00: resource 5 [mem 0xfa000000-0xffffffff] | |
| pci_bus 0001:00: resource 6 [mem 0x80000000-0x8fffffff] | |
| pci_bus 0001:00: resource 7 [mem 0xa0000000-0xefffffff] | |
| pci_bus 0001:01: resource 1 [mem 0x80000000-0x800fffff] | |
| pci_bus 0001:05: resource 1 [mem 0x80700000-0x807fffff] | |
| pci_bus 0001:02: resource 1 [mem 0x80100000-0x801fffff] | |
| pci_bus 0001:03: resource 1 [mem 0x80200000-0x805fffff] | |
| pci_bus 0001:04: resource 1 [mem 0x80600000-0x806fffff] | |
| PCI: Probing PCI hardware done | |
| bio: create slab <bio-0> at 0 | |
| vgaarb: device added: PCI:0000:f0:10.0,decodes=io+mem,owns=mem,locks=none | |
| vgaarb: loaded | |
| vgaarb: bridge control possible 0000:f0:10.0 | |
| SCSI subsystem initialized | |
| libata version 3.00 loaded. | |
| usbcore: registered new interface driver usbfs | |
| usbcore: registered new interface driver hub | |
| usbcore: registered new device driver usb | |
| Advanced Linux Sound Architecture Driver Version 1.0.25. | |
| Switching to clocksource timebase | |
| NET: Registered protocol family 2 | |
| IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) | |
| TCP established hash table entries: 524288 (order: 11, 8388608 bytes) | |
| TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) | |
| TCP: Hash tables configured (established 524288 bind 65536) | |
| TCP: reno registered | |
| UDP hash table entries: 2048 (order: 4, 65536 bytes) | |
| UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) | |
| NET: Registered protocol family 1 | |
| RPC: Registered named UNIX socket transport module. | |
| RPC: Registered udp transport module. | |
| RPC: Registered tcp transport module. | |
| RPC: Registered tcp NFSv4.1 backchannel transport module. | |
| PCI: CLS mismatch (32 != 64), using 128 bytes | |
| pci 0001:01:08.0: enabling device (0000 -> 0002) | |
| pci 0001:01:09.0: enabling device (0000 -> 0002) | |
| pci 0001:05:0b.0: enabling device (0000 -> 0002) | |
| pci 0001:05:0b.1: enabling device (0000 -> 0002) | |
| pci 0001:05:0b.2: enabling device (0004 -> 0006) | |
| Registering G5 CPU frequency driver | |
| Frequency method: i2c/pfunc, Voltage method: i2c/pfunc | |
| Low: 1310 Mhz, High: 1800 Mhz, Cur: 1800 MHz | |
| HugeTLB registered 16 MB page size, pre-allocated 0 pages | |
| NFS: Registering the id_resolver key type | |
| Installing knfsd (copyright (C) 1996 okir@monad.swb.de). | |
| msgmni has been set to 7830 | |
| Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) | |
| io scheduler noop registered | |
| io scheduler deadline registered | |
| io scheduler cfq registered (default) | |
| Generic RTC Driver v1.07 | |
| Linux agpgart interface v0.103 | |
| agpgart-uninorth 0000:f0:0b.0: Apple U3 chipset | |
| agpgart-uninorth 0000:f0:0b.0: configuring for size idx: 64 | |
| agpgart-uninorth 0000:f0:0b.0: AGP aperture is 256M @ 0x0 | |
| nvidiafb: Device ID: 10de0321 | |
| nvidiafb: CRTC0 analog not found | |
| nvidiafb: CRTC1 analog not found | |
| i2c i2c-0: unable to read EDID block. | |
| i2c i2c-0: unable to read EDID block. | |
| i2c i2c-0: unable to read EDID block. | |
| nvidiafb: EDID found from BUS2 | |
| nvidiafb: CRTC 1 is currently programmed for DFP | |
| nvidiafb: Using DFP on CRTC 1 | |
| nvidiafb: Panel size is 1280 x 1024 | |
| nvidiafb: Panel is TMDS | |
| nvidiafb: Flat panel dithering disabled | |
| Attempt to iounmap early bolted mapping at 0xd0000800800c1000 | |
| Console: switching to colour frame buffer device 160x64 | |
| nvidiafb: PCI nVidia NV32 framebuffer (64MB @ 0x98000000) | |
| MacIO PCI driver attached to K2 chipset | |
| temperature temperature: PowerMac G5 Thermal control driver 1.3 | |
| Detected fan controls: | |
| 0: PWM fan, id 1, location: BACKSIDE,SYS CTRLR FAN | |
| 1: RPM fan, id 2, location: DRIVE BAY | |
| 2: PWM fan, id 2, location: SLOT,PCI FAN | |
| 3: RPM fan, id 3, location: CPU A INTAKE | |
| 4: RPM fan, id 4, location: CPU A EXHAUST | |
| 5: RPM fan, id 5, location: CPU B INTAKE | |
| 6: RPM fan, id 6, location: CPU B EXHAUST | |
| i2c i2c-0: therm_pm72: attach_adapter method is deprecated | |
| i2c i2c-0: Please use another way to instantiate your i2c_client | |
| i2c i2c-1: therm_pm72: attach_adapter method is deprecated | |
| i2c i2c-1: Please use another way to instantiate your i2c_client | |
| i2c i2c-2: therm_pm72: attach_adapter method is deprecated | |
| i2c i2c-2: Please use another way to instantiate your i2c_client | |
| i2c i2c-0: wf_smu_sat: attach_adapter method is deprecated | |
| i2c i2c-0: Please use another way to instantiate your i2c_client | |
| i2c i2c-1: wf_smu_sat: attach_adapter method is deprecated | |
| i2c i2c-1: Please use another way to instantiate your i2c_client | |
| i2c i2c-2: wf_smu_sat: attach_adapter method is deprecated | |
| i2c i2c-2: Please use another way to instantiate your i2c_client | |
| Uniform Multi-Platform E-IDE driver | |
| ide-pmac 0001:02:0d.0: enabling device (0014 -> 0016) | |
| ide-pmac: Found Apple K2 ATA-6 controller (PCI), bus ID 3, irq 39 | |
| Probing IDE interface ide0... | |
| hda: HL-DT-ST DVD-RW GWA-4082B, ATAPI CD/DVD-ROM drive | |
| hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 | |
| hda: UDMA/66 mode selected | |
| ide0 at 0xd00008008348a000-0xd00008008348a070,0xd00008008348a160 on irq 39 | |
| ide-gd driver 1.18 | |
| ide-cd driver 5.00 | |
| ide-cd: hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache | |
| cdrom: Uniform CD-ROM driver Revision: 3.20 | |
| sata_svw 0001:04:0c.0: version 2.3 | |
| scsi0 : sata_svw | |
| scsi1 : sata_svw | |
| scsi2 : sata_svw | |
| scsi3 : sata_svw | |
| ata1: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600000 irq 16 | |
| ata2: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600100 irq 16 | |
| ata3: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600200 irq 16 | |
| ata4: SATA max UDMA/133 mmio m8192@0x80600000 port 0x80600300 irq 16 | |
| sungem.c:v1.0 David S. Miller <davem@redhat.com> | |
| gem 0001:03:0f.0: eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0d:93:35:2f:b0 | |
| firewire_ohci 0001:02:0e.0: enabling device (0000 -> 0002) | |
| firewire_ohci 0001:02:0e.0: added OHCI v1.0 device as card 0, 8 IR + 8 IT contexts, quirks 0x0 | |
| ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| ehci_hcd 0001:05:0b.2: EHCI Host Controller | |
| ehci_hcd 0001:05:0b.2: new USB bus registered, assigned bus number 1 | |
| ehci_hcd 0001:05:0b.2: irq 63, io mem 0x80700000 | |
| ehci_hcd 0001:05:0b.2: USB 2.0 started, EHCI 1.00 | |
| hub 1-0:1.0: USB hub found | |
| hub 1-0:1.0: 5 ports detected | |
| ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| ohci_hcd 0001:01:08.0: OHCI Host Controller | |
| ohci_hcd 0001:01:08.0: new USB bus registered, assigned bus number 2 | |
| ohci_hcd 0001:01:08.0: irq 27, io mem 0x80081000 | |
| hub 2-0:1.0: USB hub found | |
| hub 2-0:1.0: 2 ports detected | |
| ohci_hcd 0001:01:09.0: OHCI Host Controller | |
| ohci_hcd 0001:01:09.0: new USB bus registered, assigned bus number 3 | |
| ohci_hcd 0001:01:09.0: irq 28, io mem 0x80080000 | |
| hub 3-0:1.0: USB hub found | |
| hub 3-0:1.0: 2 ports detected | |
| ohci_hcd 0001:05:0b.0: OHCI Host Controller | |
| ohci_hcd 0001:05:0b.0: new USB bus registered, assigned bus number 4 | |
| ohci_hcd 0001:05:0b.0: irq 63, io mem 0x80702000 | |
| ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) | |
| ata1.00: ATA-7: Maxtor 6Y080M0, YAR51HW0, max UDMA/133 | |
| ata1.00: 160086528 sectors, multi 0: LBA48 | |
| ata1.00: configured for UDMA/133 | |
| scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y080M0 YAR5 PQ: 0 ANSI: 5 | |
| hub 4-0:1.0: USB hub found | |
| hub 4-0:1.0: 3 ports detected | |
| ohci_hcd 0001:05:0b.1: OHCI Host Controller | |
| ohci_hcd 0001:05:0b.1: new USB bus registered, assigned bus number 5 | |
| sd 0:0:0:0: [sda] 160086528 512-byte logical blocks: (81.9 GB/76.3 GiB) | |
| hub 1-0:1.0: unable to enumerate USB device on port 1 | |
| sd 0:0:0:0: [sda] Write Protect is off | |
| sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 | |
| sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA | |
| ohci_hcd 0001:05:0b.1: irq 63, io mem 0x80701000 | |
| sd 0:0:0:0: Attached scsi generic sg0 type 0 | |
| sda: [mac] sda1 sda2 sda3 sda4 | |
| sd 0:0:0:0: [sda] Attached SCSI disk | |
| hub 1-0:1.0: unable to enumerate USB device on port 4 | |
| hub 5-0:1.0: USB hub found | |
| hub 5-0:1.0: 2 ports detected | |
| mousedev: PS/2 mouse device common for all mice | |
| i2c /dev entries driver | |
| i2c i2c-3: therm_pm72: attach_adapter method is deprecated | |
| i2c i2c-3: Please use another way to instantiate your i2c_client | |
| i2c i2c-3: wf_smu_sat: attach_adapter method is deprecated | |
| i2c i2c-3: Please use another way to instantiate your i2c_client | |
| PowerMac i2c bus pmu 2 registered | |
| i2c i2c-4: therm_pm72: attach_adapter method is deprecated | |
| i2c i2c-4: Please use another way to instantiate your i2c_client | |
| i2c i2c-4: wf_smu_sat: attach_adapter method is deprecated | |
| i2c i2c-4: Please use another way to instantiate your i2c_client | |
| PowerMac i2c bus pmu 1 registered | |
| i2c i2c-5: therm_pm72: attach_adapter method is deprecated | |
| i2c i2c-5: Please use another way to instantiate your i2c_client | |
| i2c i2c-5: wf_smu_sat: attach_adapter method is deprecated | |
| i2c i2c-5: Please use another way to instantiate your i2c_client | |
| PowerMac i2c bus mac-io 0 registered | |
| i2c i2c-6: therm_pm72: attach_adapter method is deprecated | |
| i2c i2c-6: Please use another way to instantiate your i2c_client | |
| i2c i2c-6: wf_smu_sat: attach_adapter method is deprecated | |
| i2c i2c-6: Please use another way to instantiate your i2c_client | |
| PowerMac i2c bus u3 1 registered | |
| i2c i2c-7: therm_pm72: attach_adapter method is deprecated | |
| i2c i2c-7: Please use another way to instantiate your i2c_client | |
| i2c i2c-7: wf_smu_sat: attach_adapter method is deprecated | |
| i2c i2c-7: Please use another way to instantiate your i2c_client | |
| PowerMac i2c bus u3 0 registered | |
| cpuidle: using governor ladder | |
| cpuidle: using governor menu | |
| FCU Initialized, RPM fan shift is 3 | |
| usbcore: registered new interface driver usbhid | |
| usbhid: USB HID core driver | |
| snd-powermac no longer handles any machines with a layout-id property in the device-tree, use snd-aoa. | |
| oprofile: using ppc64/970 performance monitoring. | |
| IPv4 over IPv4 tunneling driver | |
| TCP: cubic registered | |
| NET: Registered protocol family 10 | |
| IPv6 over IPv4 tunneling driver | |
| NET: Registered protocol family 17 | |
| Registering the dns_resolver key type | |
| input: PMU as /devices/virtual/input/input0 | |
| ALSA device list: | |
| No soundcards found. | |
| firewire_core 0001:02:0e.0: created device fw0: GUID 000d93fffe352fb0, S800 | |
| ata2: SATA link down (SStatus 4 SControl 300) | |
| usb 4-1: new low-speed USB device number 2 using ohci_hcd | |
| input: NOVATEK USB Keyboard as /devices/pci0001:00/0001:00:02.0/0001:05:0b.0/usb4/4-1/4-1:1.0/input/input1 | |
| generic-usb 0003:0603:00F2.0001: input: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0001:05:0b.0-1/input0 | |
| input: NOVATEK USB Keyboard as /devices/pci0001:00/0001:00:02.0/0001:05:0b.0/usb4/4-1/4-1:1.1/input/input2 | |
| generic-usb 0003:0603:00F2.0002: input,hiddev0: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0001:05:0b.0-1/input1 | |
| ata3: SATA link down (SStatus 4 SControl 300) | |
| usb 5-2: new low-speed USB device number 2 using ohci_hcd | |
| input: Logitech Optical USB Mouse as /devices/pci0001:00/0001:00:02.0/0001:05:0b.1/usb5/5-2/5-2:1.0/input/input3 | |
| generic-usb 0003:046D:C016.0003: input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0001:05:0b.1-2/input0 | |
| ata4: SATA link down (SStatus 4 SControl 300) | |
| EXT3-fs (sda4): error: couldn't mount because of unsupported optional features (240) | |
| EXT2-fs (sda4): error: couldn't mount because of unsupported optional features (240) | |
| EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null) | |
| VFS: Mounted root (ext4 filesystem) readonly on device 8:4. | |
| Freeing unused kernel memory: 300k freed | |
| udevd[1215]: starting version 171 | |
| snd-aoa-fabric-layout: Using PMF GPIOs | |
| i2c i2c-0: aoa_codec_tas: attach_adapter method is deprecated | |
| i2c i2c-0: Please use another way to instantiate your i2c_client | |
| i2c i2c-1: aoa_codec_tas: attach_adapter method is deprecated | |
| i2c i2c-1: Please use another way to instantiate your i2c_client | |
| i2c i2c-2: aoa_codec_tas: attach_adapter method is deprecated | |
| i2c i2c-2: Please use another way to instantiate your i2c_client | |
| i2c i2c-3: aoa_codec_tas: attach_adapter method is deprecated | |
| i2c i2c-3: Please use another way to instantiate your i2c_client | |
| i2c i2c-4: aoa_codec_tas: attach_adapter method is deprecated | |
| i2c i2c-4: Please use another way to instantiate your i2c_client | |
| i2c i2c-5: aoa_codec_tas: attach_adapter method is deprecated | |
| i2c i2c-5: Please use another way to instantiate your i2c_client | |
| snd-aoa-codec-tas: found 'deq' node | |
| snd-aoa-fabric-layout: can use this codec | |
| snd-aoa-codec-tas: tas found, addr 0x35 on /ht@0,f2000000/pci@1/mac-io@7/i2c@18000/deq@6a | |
| i2c i2c-6: aoa_codec_tas: attach_adapter method is deprecated | |
| i2c i2c-6: Please use another way to instantiate your i2c_client | |
| i2c i2c-7: aoa_codec_tas: attach_adapter method is deprecated | |
| i2c i2c-7: Please use another way to instantiate your i2c_client | |
| EXT4-fs (sda4): re-mounted. Opts: (null) | |
| Adding 524284k swap on /dev/sda3. Priority:-1 extents:1 across:524284k | |
| sungem_phy: PHY ID: 2062e0, addr: 1 | |
| gem 0001:03:0f.0: eth0: Found BCM5421-K2 PHY |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment