OMRON LUNA-II and NetBSD/luna68k boot messages including ROM monitor and blandnew native bootloader

LUNA-II boot message

Diagnostic Start....(c) Copyright OMRON Corporation 1991
         All Rights Reserved
    ROM Version 1.11, 16 Megabytes RAM, 1 CPU
    Memory Check: 3Port passed, main skipped.
ROM mode
0>h
=============< HELP MESSAGE >=====================================
  h[H]----> Help
  k[K]----> Set Boot-file constant
  g[G]----> Load Binary file
  m[M]----> Load S-record file
  x[X]----> Program execution
  r[R]----> Register Display or Modify
  s[S]----> Display SCSI-Device Vendor name
  t[T]----> Trace-mode Set or Reset
  u[U]----> Control UART-Channel
  z[Z]----> Breakpoint Display or Set or Reset
  i[I]----> Disassemble memory
  o[O]----> Power Off
  j[J]----> Hard-Copy
  install-> useful command for install booting
  nvram---> System-parameter (in nvram) Display/Modify/Reset
  status--> Display cpu[s] status 
  >   ----> MMU ATC flush
  !   ----> Reset
  ?," ----> Memory Search
  wql ----> Memory Display or Modify
  *   ----> Change NVRAM clock status
=============< HELP MESSAGE >=====================================
0>hk
=============< HELP MESSAGE >=====================================
         ***** k[K] - Set Boot-file constant *****
This command is   ["K"]  Set constant of boot-file,
  	  ["K-"] Set default constant (initialize),
		  ["K+"] Change default constant.
  This Command is Dialog type.   Set items are following.
    ctlr -> Device-controller(dk, ft, sd, st, p0, p1)
             dk    --> Hard-Disk        ft    --> Floppy-Disk
             sd, st--> Streamer-Tape    p0, p1--> RS232c
            File-format is following
             dk    --> UNIX file-system ft, st--> TAR format
             sd    --> DD format        p0, p1--> S-Record
      id -> SPCnumber and SCSIid
            =Format=
              SCSIid<CR>
              SPCnumber-SCSIid<CR>
            =Example=
              4<CR>            <-- SPC=0, ID=4
              1-5<CR>          <-- SPC=1, ID=5
     par -> Partition-number
   fname -> File-name
     fno -> File-number
 =Format=
   K<CR>
   K-<CR>
   K+<CR>
=============< HELP MESSAGE >=====================================
0>k
ctlr: dk  
id: 0-6  1-6
par: a  d
fnam: boot  
0>hg
=============< HELP MESSAGE >=====================================
         ***** g[G] - Load Binary file *****
This command is
  Load binary-file from device specified by K-command.
  Device-controller is dk,ft,sd,st.
  If address is not specify, loading address is decided by
  entry address of file.
 =Format=
   addressG file<CR>,      addressG<CR>
   G file<CR>,             G<CR>
        "address" ---- Loading address.
        "file"    ---- File name.
 =Example=
   10000g /bin/unix<CR> ---- Load "/bin/unix" at 0x10000.
=============< HELP MESSAGE >=====================================
0>g
0>hx
=============< HELP MESSAGE >=====================================
         ***** x[X] - Program execution *****
This command is
  Execute program specified by address.
  If address is not specify, execute address is decided by
  entry address of file, or discontinue address of Breakpoint
  and Trace and Abort.
 =Format=
   addressX<CR>,          X<CR>
        "address" ---- Execution address.
 =Example=
   10000x<CR>        ---- Execute 0x10000.
=============< HELP MESSAGE >=====================================
0>x -a

>> NetBSD/luna68k boot, Revision 1.2 (Tue Jan 15 00:59:19 JST 2013)
>> (based on Stinger ver 0.0 [Phase-31])

Machine model   = LUNA-II
Physical Memory = 0x1000000  (16 MB)

sc0: async, parity, scsi id 7
sc0 at 0xe1000000, ipl 2
sd0: IBM DPES-31080 rev S31Q, 2118143 512 byte blocks
sd0 at sc0, slave 6
sc1: async, parity, scsi id 7
sc1 at 0xe1000040, ipl 2
sd2: MELCO DSC-G rev 1.00, 62533295 512 byte blocks
sd2 at sc1, slave 6
le0: Am7990 LANCE Ethernet, mem at 0x71010000
le0: Ethernet address = 00:00:0a:03:42:77
le0 at 0xf1000000

boot> boot sd(2,0)netbsd
Booting sd(2,0)netbsd
1811152+88304 [275552+155268]=0x2390b0
[ Kernel symbol table invalid! ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.0.1 (GENERIC)
LUNA-II (MC68040 CPU+MMU+FPU, 4k on-chip physical I/D caches)
total memory = 16384 KB
avail memory = 13396 KB
mainbus0 (root)
clock0 at mainbus0: ds1287a
le0 at mainbus0: address 00:00:0a:03:42:77
le0: 32 receive buffers, 8 transmit buffers
sio0 at mainbus0: uPD7201A
siotty0 at sio0 channel 0 (console)
ws0 at sio0 channel 1
wskbd0 at ws0 (mux ignored)
wsmouse0 at ws0 (mux ignored)
fb0 at mainbus0: 1280 x 1024, 1bpp
wsdisplay0 at fb0 (kbdmux ignored)
spc0 at mainbus0
scsibus0 at spc0: 8 targets, 8 luns per target
spc1 at mainbus0
scsibus1 at spc1: 8 targets, 8 luns per target
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 3 lun 0: <TEAC, FC-1     HGF  10, RV C> disk removable
sd0: 1440 KB, 80 cyl, 2 head, 18 sec, 512 bytes/sect x 2880 sectors
sd0: async, 8-bit transfers
sd1 at scsibus0 target 6 lun 0: <IBM, DPES-31080, S31Q> disk fixed
sd1: 1034 MB, 4903 cyl, 4 head, 108 sec, 512 bytes/sect x 2118144 sectors
sd1: async, 8-bit transfers
sd2 at scsibus1 target 6 lun 0: <MELCO, DSC-G, 1.00> disk fixed
sd2: 30533 MB, 62037 cyl, 16 head, 63 sec, 512 bytes/sect x 62533296 sectors
sd2: async, 8-bit transfers
boot device: sd0
sd0: no disk label
root device (default sd0a): sd2
dump device (default sd2b): 
file system (default generic): 
root on sd2a dumps on sd2b
root file system type: ffs
init path (default /sbin/init): 
init: trying /sbin/init
Tue Jan 15 04:40:19 JST 2013
Starting root file system check:
/dev/rsd2a: file system is clean; not checking
swapctl: adding /dev/sd2b as swap device at priority 0
Starting file system checks:
/dev/rsd1a: file system is clean; not checking
Setting tty flags.
Setting sysctl variables:
ddb.onpanic: 1 -> 0
Starting network.
Hostname: lunachild
Configuring network interfaces: le0.
Adding interface aliases:.
Building databases: dev, utmp, utmpx.
Starting syslogd.
Mounting all filesystems...
Clearing temporary files.
Updating fontconfig cache: done.
Creating a.out runtime link editor directory cache.
Checking quotas: done.
Setting securelevel: kern.securelevel: 0 -> 1
Starting virecover.
Checking for core dump...
savecore: no core dump
Starting local daemons:.
Updating motd.
Starting inetd.
Starting cron.
Tue Jan 15 04:41:57 JST 2013
Jan 15 04:42:00 lunachild getty[323]: /dev/ttyE0: Device not configured

NetBSD/luna68k (lunachild) (ttya)

login: root
Jan 15 05:04:10 lunachild login: ROOT LOGIN (root) on tty ttya
Last login: Mon Jan 14 17:53:31 2013 on ttyE0
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.0.1 (GENERIC)
Terminal type is vt100.
We recommend that you create a non-root account and use su(1) for root access.
lunachild#