Created
May 28, 2017 14:35
-
-
Save u1735067/1740510b2664ca753df4c43cc9c54843 to your computer and use it in GitHub Desktop.
DNS-320LW Rev. A1 firmware v1.09b06 -- trying to debug the "can't boot unless has been in the fridge" temperature / thermal sensor issue -- I now know it's due to the Weltrend WT69P3 chip ; next step : try to UART connect this shit.
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| ** MARVELL BOARD: DB-88F6702A-BP LE | |
| U-Boot 1.1.4 (Mar 12 2012 - 16:23:48) Marvell version: 3.6.0.DNS-320L.01 | |
| U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 | |
| Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz | |
| SysClock = 400Mhz , TClock = 166Mhz | |
| DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 | |
| DRAM CS[0] base 0x00000000 size 256MB | |
| DRAM Total size 256MB 16bit width | |
| Addresses 8M - 0M are saved for the U-Boot usage. | |
| Mem malloc Initialization (8M - 7M): Done | |
| NAND:128 MB | |
| Flash: 0 kB | |
| CPU : Marvell Feroceon (Rev 1) | |
| Streaming disabled | |
| Write allocate disabled | |
| USB 0: host mode | |
| PEX 0: interface detected no Link. | |
| Net: egiga0 [PRIME] | |
| Hit any key to stop autoboot: 0 | |
| NAND read: device 0 offset 0x100000, size 0x300000 | |
| load addr .... =a00000 | |
| 3145728 bytes read: OK | |
| NAND read: device 0 offset 0x600000, size 0x300000 | |
| load addr .... =f00000 | |
| 3145728 bytes read: OK | |
| ## Booting image at 00a00000 ... | |
| Image Name: Linux-2.6.31.8 | |
| Created: 2012-08-22 8:55:08 UTC | |
| Image Type: ARM Linux Kernel Image (uncompressed) | |
| Data Size: 2630552 Bytes = 2.5 MB | |
| Load Address: 00008000 | |
| Entry Point: 00008000 | |
| Verifying Checksum ... OK | |
| OK | |
| ## Loading Ramdisk Image at 00f00000 ... | |
| Image Name: Ramdisk | |
| Created: 2017-01-11 9:45:21 UTC | |
| Image Type: ARM Linux RAMDisk Image (gzip compressed) | |
| Data Size: 1750374 Bytes = 1.7 MB | |
| Load Address: 00e00000 | |
| Entry Point: 00e00000 | |
| Verifying Checksum ... OK | |
| Starting kernel ... | |
| Uncompressing Linux......................................................................................................................................................................... done, booti | |
| ng the kernel. | |
| Linux version 2.6.31.8 (jack@swtest6) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #1 Wed Aug 22 16:55:05 CST 2012 | |
| CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 | |
| CPU: VIVT data cache, VIVT instruction cache | |
| Machine: Feroceon-KW | |
| Using UBoot passing parameters structure | |
| Memory policy: ECC disabled, Data cache writeback | |
| Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024 | |
| Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none | |
| PID hash table entries: 1024 (order: 10, 4096 bytes) | |
| Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | |
| Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | |
| Memory: 256MB = 256MB total | |
| Memory: 246272KB available (4960K code, 334K data, 136K init, 0K highmem) | |
| Hierarchical RCU implementation. | |
| NR_IRQS:128 | |
| Console: colour dummy device 80x30 | |
| Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120) | |
| Mount-cache hash table entries: 512 | |
| CPU: Testing write buffer coherency: ok | |
| NET: Registered protocol family 16 | |
| Feroceon L2: Enabling L2 | |
| Feroceon L2: Cache support initialised. | |
| CPU Interface | |
| ------------- | |
| SDRAM_CS0 ....base 00000000, size 256MB | |
| SDRAM_CS1 ....disable | |
| SDRAM_CS2 ....disable | |
| SDRAM_CS3 ....disable | |
| PEX0_MEM ....base e0000000, size 128MB | |
| PEX0_IO ....base f2000000, size 1MB | |
| PEX1_MEM ....no such | |
| PEX1_IO ....no such | |
| INTER_REGS ....base f1000000, size 1MB | |
| NFLASH_CS ....base fa000000, size 2MB | |
| SPI_CS ....base f4000000, size 16MB | |
| BOOT_ROM_CS ....no such | |
| DEV_BOOTCS ....no such | |
| CRYPT_ENG ....base f0000000, size 2MB | |
| Marvell Development Board (LSP Version KW_LSP_5.1.3_patch29)-- DB-88F6702A-BP Soc: 88F6702 A1 LE | |
| Detected Tclk 166666667 and SysClk 400000000 | |
| MV Buttons Device Load | |
| Marvell USB EHCI Host controller #0: c8040740 | |
| PEX0 interface detected no Link. | |
| PCI: bus0: Fast back to back transfers enabled | |
| mvPexLocalBusNumSet: ERR. Invalid PEX interface 1 | |
| bio: create slab <bio-0> at 0 | |
| SCSI subsystem initialized | |
| usbcore: registered new interface driver usbfs | |
| usbcore: registered new interface driver hub | |
| usbcore: registered new device driver usb | |
| NET: Registered protocol family 2 | |
| IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| TCP established hash table entries: 8192 (order: 4, 65536 bytes) | |
| TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
| TCP: Hash tables configured (established 8192 bind 8192) | |
| TCP reno registered | |
| NET: Registered protocol family 1 | |
| Trying to unpack rootfs image as initramfs... | |
| rootfs image is not initramfs (no cpio magic); looks like an initrd | |
| Freeing initrd memory: 1708K | |
| RTC has been updated!!! | |
| rtc mv_rtc: rtc core: registered kw-rtc as rtc0 | |
| RTC registered | |
| cpufreq: Init kirkwood cpufreq driver | |
| XOR registered 4 channels | |
| XOR 2nd invalidate WA enabled | |
| cesadev_init(c000ed5c) | |
| mvCesaInit: sessions=640, queue=64, pSram=f0000000 | |
| MV Buttons Driver Load | |
| VFS: Disk quotas dquot_6.5.2 | |
| Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) | |
| squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| Installing knfsd (copyright (C) 1996 okir@monad.swb.de). | |
| NTFS driver 2.1.29 [Flags: R/O]. | |
| JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. | |
| fuse init (API version 7.12) | |
| msgmni has been set to 484 | |
| alg: No test for cipher_null (cipher_null-generic) | |
| alg: No test for ecb(cipher_null) (ecb-cipher_null) | |
| alg: No test for digest_null (digest_null-generic) | |
| alg: No test for compress_null (compress_null-generic) | |
| alg: No test for lzma (lzma-generic) | |
| alg: No test for stdrng (krng) | |
| alg: No test for hmac(digest_null) (hmac(digest_null-generic)) | |
| Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) | |
| io scheduler noop registered | |
| io scheduler anticipatory registered (default) | |
| Initializing ths8200_init | |
| Initializing dove_adi9889_init | |
| Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled | |
| serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A | |
| console [ttyS0] enabled | |
| serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A | |
| brd: module loaded | |
| loop: module loaded | |
| Integrated Sata device found | |
| IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs | |
| scsi0 : Marvell SCSI to SATA adapter | |
| scsi1 : Marvell SCSI to SATA adapter | |
| Loading Marvell Ethernet Driver: | |
| o Cached descriptors in DRAM | |
| o DRAM SW cache-coherency | |
| o 2 Giga ports supported | |
| o Single RX Queue support - ETH_DEF_RXQ=0 | |
| o Single TX Queue support - ETH_DEF_TXQ=0 | |
| o TCP segmentation offload (TSO) supported | |
| o Large Receive offload (LRO) supported | |
| o Receive checksum offload supported | |
| o Transmit checksum offload supported | |
| o Network Fast Processing (Routing) supported - (Disabled) | |
| o Driver ERROR statistics enabled | |
| o Proc tool API enabled | |
| o SKB Reuse supported - (Disabled) | |
| o SKB Recycle supported - (Disabled) | |
| o Rx descripors: q0=128 | |
| o Tx descripors: q0=532 | |
| o Loading network interface(s): | |
| o register under mv88fx_eth platform | |
| o egiga0, ifindex = 2, GbE port = 0 | |
| Warning: Giga 1 is Powered Off | |
| mvFpRuleDb (c0ee4000): 2048 entries, 8192 bytes | |
| Counter=0, opIdx=6, overhead=16 | |
| Counter=1, opIdx=2, overhead=0 | |
| Counter=2, opIdx=1, overhead=18 | |
| Counter=3, opIdx=2, overhead=0 | |
| NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) | |
| Scanning device for bad blocks | |
| Using static partition definition | |
| Creating 7 MTD partitions on "nand_mtd": | |
| 0x000000000000-0x000000100000 : "u-boot" | |
| 0x000000100000-0x000000600000 : "uImage" | |
| 0x000000600000-0x000000b00000 : "ramdisk" | |
| 0x000000b00000-0x000006f00000 : "image" | |
| 0x000006f00000-0x000007900000 : "rescue firmware" | |
| 0x000007900000-0x000007e00000 : "config" | |
| 0x000007e00000-0x000008000000 : "my-dlink" | |
| ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| ehci_marvell ehci_marvell.70059: Marvell Orion EHCI | |
| ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 | |
| ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 | |
| ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 | |
| usb usb1: configuration #1 chosen from 1 choice | |
| hub 1-0:1.0: USB hub found | |
| hub 1-0:1.0: 1 port detected | |
| ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| uhci_hcd: USB Universal Host Controller Interface driver | |
| Initializing USB Mass Storage driver... | |
| usbcore: registered new interface driver usb-storage | |
| USB Mass Storage support registered. | |
| mice: PS/2 mouse device common for all mice | |
| i2c /dev entries driver | |
| md: linear personality registered for level -1 | |
| md: raid0 personality registered for level 0 | |
| md: raid1 personality registered for level 1 | |
| device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com | |
| usbcore: registered new interface driver usbhid | |
| usbhid: v2.6:USB HID core driver | |
| TCP cubic registered | |
| NET: Registered protocol family 17 | |
| RPC: Registered udp transport module. | |
| RPC: Registered tcp transport module. | |
| rtc mv_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) | |
| md: Waiting for all devices to be available before autodetect | |
| md: If you don't use raid, use raid=noautodetect | |
| md: Autodetecting RAID arrays. | |
| md: Scanned 0 and added 0 devices. | |
| md: autorun ... | |
| md: ... autorun DONE. | |
| RAMDISK: gzip image found at block 0 | |
| VFS: Mounted root (ext2 filesystem) on device 1:0. | |
| Freeing init memory: 136K | |
| init started: BusyBox v1.20.2 (2016-01-27 17:36:49 CST) | |
| starting pid 536, tty '': '/etc/rc.sh' | |
| ** Mounting /etc/fstab | |
| umount: can't umount /proc: Invalid argument | |
| umount: can't umount /usr/local/modules: Invalid argument | |
| sh: can't open '/usr/sbin/pre_usb.sh' | |
| first good block is 0 | |
| image len = 40693760 , image checksum = f602740 | |
| umount: can't umount /usr/local/tmp: Invalid argument | |
| dump image checksum=f602740 | |
| mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules | |
| ln: /lib/./libnss_dns-2.8.so: File exists | |
| ln: /lib/./libnss_dns.so.2: File exists | |
| ln: /usr/sbin/./system_init: File exists | |
| hardware init | |
| GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1 | |
| mtd check v1.02.08062012 | |
| config mtd type is JFFS2 | |
| /usr/local/config free size is 4726784 | |
| ** copy config files | |
| usbcore: registered new interface driver usblp | |
| ** set loopback interface | |
| old firmware ver:20170111 | |
| new firmware ver:20170111 | |
| first good block is 0 | |
| mac1 = AC:F1:DF:10:xx:xx | |
| lan0:ifconfig egiga0 hw ether AC:F1:DF:10:xx:xx | |
| egiga0: mac address changed | |
| egiga0: started | |
| Support Mydlink | |
| NET: Registered protocol family 10 | |
| lo: Disabled Privacy Extensions | |
| ADDRCONF(NETDEV_UP): egiga0: link is not ready | |
| IPv6 over IPv4 tunneling driver | |
| sit0: Disabled Privacy Extensions | |
| ip6tnl0: Disabled Privacy Extensions | |
| IPv4 over IPv4 tunneling driver | |
| tunl0: Disabled Privacy Extensions | |
| net.ipv6.conf.default.accept_dad = 2 | |
| net.ipv6.conf.egiga0.accept_dad = 2 | |
| net.ipv6.conf.default.dad_transmits = 1 | |
| net.ipv6.conf.egiga0.dad_transmits = 1 | |
| net.ipv6.conf.default.forwarding = 0 | |
| net.ipv6.conf.default.accept_redirects = 1 | |
| *** execute rc.init.sh | |
| awk: /var/run/udhcpc0.pid: No such file or directory | |
| RTNETLINK answers: Cannot assign requested address | |
| route: SIOCDELRT: No such process | |
| killall: crond: no process killed | |
| rtc: RTC time = 2017/5/28 Sun 14:4:35 | |
| *** set Time Zone **** | |
| Sun May 28 14:04:35 CEST 2017 | |
| *** get Time from rtc and set it into system **** | |
| rtc: RTC time = 2017/5/28 Sun 14:4:36 | |
| Sun May 28 16:04:36 CEST 2017 | |
| *** Do not adjust RTC time *** | |
| Module IPC SERVER Version:(1.00.20090706) | |
| ads=0 | |
| created mail daemon thread 0 | |
| /usr/sbin/system_init: line 487: op_server: not found | |
| Starting system message bus | |
| Command: wget -T5 -t3 -q http://cfaj.freeshell.org/ipaddr.cgi -O /tmp/exip.0 | |
| LLTDIF= egiga0 | |
| Command: wget -T5 -t3 -q http://icanhazip.com/ -O /tmp/exip.1 | |
| Stop NFS Deamon.... | |
| Stop NFS mountd.... | |
| Unload Driver.... | |
| Stop Portmap. | |
| No NFS information . | |
| Stop NFS Server OVER. | |
| Start config the NFS needed file.... | |
| Config Over. | |
| No NFS information . | |
| Start portmap.... | |
| Load Driver . | |
| Start NFS Deamon . | |
| svc: failed to register lockdv1 RPC service (errno 97). | |
| NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory | |
| NFSD: unable to find recovery directory /var/lib/nfs/v4recovery | |
| NFSD: starting 90-second grace period | |
| Start NFS Server OVER . | |
| Command: wget -T5 -t3 -q http://ifconfig.me/ip -O /tmp/exip.2 | |
| Command: wget -T5 -t3 -q http://whatismyip.org/ -O /tmp/exip.3 | |
| Command: wget -T5 -t3 -q http://ifconfig.me/ip -O /tmp/exip.4 | |
| Command: wget -T5 -t3 -q http://checkip.dyndns.com:8245/ -O /tmp/exip.5 | |
| Illegal instruction | |
| enable ssh server | |
| cp: can't stat '/usr/local/config/Mydlink_Status.xml': No such file or directory | |
| mcu version 1.02 | |
| system daemon v1.03.20130707 | |
| killall: chk_hotplug: no process killed | |
| chk_io v1.03.20130502 | |
| killall: smbd: no process killed | |
| mfg_start version 1.00(2017-01-11) | |
| Sun May 28 16:05:13 2017 | |
| usb_dir [] | |
| cp: can't stat '/usr/local/config/mydlink_time.xml': No such file or directory | |
| 2017-05-28 16:05:12: (../../src/log.c.166) server started | |
| sh: you need to specify whom to kill | |
| killall: dcp: no process killed | |
| killall: signalc: no process killed | |
| killall: upnpc-ddns: no process killed | |
| LED_POWER_ON | |
| killall: tsa: no process killed | |
| opt.local stop ok. | |
| opt.local start ok. | |
| usb_dir [/] | |
| filename_mfg mfg_DNS_320LW | |
| check //mfg_DNS_320LW file | |
| open //mfg_DNS_320LW file failed | |
| Please press Enter to activate this console. | |
| starting pid 1957, tty '/dev/ttyS0': '/bin/login' | |
| Password of admin: | |
| BusyBox v1.20.2 (2016-01-27 17:36:49 CST) built-in shell (ash) | |
| Enter 'help' for a list of built-in commands. | |
| / # ls | |
| bin home lost+found opt sbin usr | |
| dev lib mnt proc sys var | |
| etc linuxrc mydlink root tmp | |
| / # | |
| / # htop | |
| -sh: htop: not found | |
| / # top | |
| Mem: 106548K used, 141868K free, 0K shrd, 8176K buff, 67836K cached | |
| CPU: 0.0% usr 0.0% sys 0.0% nic 100% idle 0.0% io 0.0% irq 0.0% sirq | |
| Load average: 0.03 0.21 0.12 1/64 3099 | |
| PID PPID USER STAT VSZ %VSZ CPU %CPU COMMAND | |
| 3099 1957 root R 2656 1.0 0 0.0 top | |
| 1902 1822 root S 19800 7.9 0 0.0 /usr/bin/php-cgi | |
| 2038 1902 root S 19800 7.9 0 0.0 /usr/bin/php-cgi | |
| 2039 1902 root S 19800 7.9 0 0.0 /usr/bin/php-cgi | |
| 1633 1 root S 11156 4.4 0 0.0 mail_daemon | |
| 1779 1 root S 8804 3.5 0 0.0 and | |
| 1822 1816 root S 6364 2.5 0 0.0 /usr/sbin/lighttpd -D -m /usr/ligh | |
| 1989 1 root S 5824 2.3 0 0.0 ddp | |
| 1778 1 root S 4904 1.9 0 0.0 /usr/sbin/sshd -f /etc/ssh/sshd_co | |
| 1816 1 root S 4380 1.7 0 0.0 /usr/sbin/lighttpd-angel -D -m /us | |
| 1921 1 root S 3080 1.2 0 0.0 /mydlink/signalc | |
| 1673 1 root S 2796 1.1 0 0.0 avahi-daemon: running [Taurus.loca | |
| 1957 1 root S 2732 1.0 0 0.0 -sh | |
| 1599 1 root S 2728 1.0 0 0.0 crond -L /dev/null | |
| 1 0 root S 2656 1.0 0 0.0 init | |
| 1922 1 root S 2656 1.0 0 0.0 {mydlink-watch-d} /bin/sh /mydlink | |
| 3096 1922 root S 2524 1.0 0 0.0 sleep 5 | |
| 1670 1 messageb S 2348 0.9 0 0.0 /usr/bin/dbus-daemon --system | |
| 1464 1 root S 2296 0.9 0 0.0 xmldb -n config | |
| 1844 1 root S 2064 0.8 0 0.0 system_daemon | |
| / # free | |
| total used free shared buffers | |
| Mem: 248416 106608 141808 0 8176 | |
| -/+ buffers: 98432 149984 | |
| Swap: 0 0 0 | |
| / # exit | |
| process '/bin/login' (pid 1957) exited. Scheduling for restart. | |
| Please press Enter to activate this console. | |
| starting pid 3147, tty '/dev/ttyS0': '/bin/login' | |
| Password of admin: | |
| BusyBox v1.20.2 (2016-01-27 17:36:49 CST) built-in shell (ash) | |
| Enter 'help' for a list of built-in commands. | |
| / # date | |
| Sun May 28 16:09:40 CEST 2017 | |
| / # reboot | |
| The system is going down NOW! | |
| Sent SIGTERM to all processes | |
| Block size total free used max | |
| ---------- ----- ----- ----- ----- | |
| 2^001 0 0 0 0 | |
| 2^002 0 0 0 0 | |
| 2^003 0 0 0 0 | |
| 2^004 0 0 0 0 | |
| 2^005 0 0 0 0 | |
| 2^006 0 0 0 0 | |
| 2^007 0 0 0 0 | |
| 2^008 0 0 0 0 | |
| 2^009 0 0 0 0 | |
| 2^010 0 0 0 0 | |
| 2^011 0 0 0 0 | |
| 2^012 0 0 0 0 | |
| 2^013 0 0 0 0 | |
| 2^014 0 0 0 0 | |
| 2^015 0 0 0 0 | |
| 2^016 0 0 0 0 | |
| 2^017 0 0 0 0 | |
| 2^018 0 0 0 0 | |
| 2^019 0 0 0 0 | |
| 2^020 0 0 0 0 | |
| 2^021 0 0 0 0 | |
| 2^022 0 0 0 0 | |
| 2^023 0 0 0 0 | |
| ------------------------------------------ | |
| total size : 0 bytes | |
| free size : 0 bytes | |
| used size : 0 bytes | |
| !!! Module IPC Terminated !!! | |
| !!! AND Server Terminated !!! | |
| 2017-05-28 16:09:44: (../../src/server.c.1512) server stopped by UID = 0 PID = 1 | |
| ../../src/lighttpd-angel.c.140: child (pid=1822) exited normally with exitcode: 0 | |
| Block size total free used max | |
| ---------- ----- ----- ----- ----- | |
| 2^001 0 0 0 0 | |
| 2^002 0 0 0 0 | |
| 2^003 192 192 0 188 | |
| 2^004 24 24 0 22 | |
| 2^005 56 56 0 56 | |
| 2^006 344 344 0 342 | |
| 2^007 0 0 0 0 | |
| 2^008 0 0 0 0 | |
| 2^009 0 0 0 0 | |
| 2^010 0 0 0 0 | |
| 2^011 8 8 0 1 | |
| 2^012 0 0 0 0 | |
| 2^013 0 0 0 0 | |
| 2^014 0 0 0 0 | |
| 2^015 0 0 0 0 | |
| 2^016 0 0 0 0 | |
| 2^017 0 0 0 0 | |
| 2^018 0 0 0 0 | |
| 2^019 0 0 0 0 | |
| 2^020 0 0 0 0 | |
| 2^021 0 0 0 0 | |
| 2^022 0 0 0 0 | |
| 2^023 0 0 0 0 | |
| ------------------------------------------ | |
| total size : 42112 bytes | |
| free size : 42112 bytes | |
| used size : 0 bytes | |
| Sent SIGKILL to all processes | |
| md: stopping all md devices. | |
| Restarting system. | |
| Reseting !! | |
| ** MARVELL BOARD: DB-88F6702A-BP LE | |
| U-Boot 1.1.4 (Mar 12 2012 - 16:23:48) Marvell version: 3.6.0.DNS-320L.01 | |
| U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00 | |
| Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz | |
| SysClock = 400Mhz , TClock = 166Mhz | |
| DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 | |
| DRAM CS[0] base 0x00000000 size 256MB | |
| DRAM Total size 256MB 16bit width | |
| Addresses 8M - 0M are saved for the U-Boot usage. | |
| Mem malloc Initialization (8M - 7M): Done | |
| NAND:128 MB | |
| Flash: 0 kB | |
| CPU : Marvell Feroceon (Rev 1) | |
| Streaming disabled | |
| Write allocate disabled | |
| USB 0: host mode | |
| PEX 0: interface detected no Link. | |
| Net: egiga0 [PRIME] | |
| Hit any key to stop autoboot: 0 | |
| NAND read: device 0 offset 0x100000, size 0x300000 | |
| load addr .... =a00000 | |
| 3145728 bytes read: OK | |
| NAND read: device 0 offset 0x600000, size 0x300000 | |
| load addr .... =f00000 | |
| 3145728 bytes read: OK | |
| ## Booting image at 00a00000 ... | |
| Image Name: Linux-2.6.31.8 | |
| Created: 2012-08-22 8:55:08 UTC | |
| Image Type: ARM Linux Kernel Image (uncompressed) | |
| Data Size: 2630552 Bytes = 2.5 MB | |
| Load Address: 00008000 | |
| Entry Point: 00008000 | |
| Verifying Checksum ... OK | |
| OK | |
| ## Loading Ramdisk Image at 00f00000 ... | |
| Image Name: Ramdisk | |
| Created: 2017-01-11 9:45:21 UTC | |
| Image Type: ARM Linux RAMDisk Image (gzip compressed) | |
| Data Size: 1750374 Bytes = 1.7 MB | |
| Load Address: 00e00000 | |
| Entry Point: 00e00000 | |
| Verifying Checksum ... OK | |
| Starting kernel ... | |
| Uncompressing Linux......................................................................................................................................................................... done, booti | |
| ng the kernel. | |
| Linux version 2.6.31.8 (jack@swtest6) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #1 Wed Aug 22 16:55:05 CST 2012 | |
| CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 | |
| CPU: VIVT data cache, VIVT instruction cache | |
| Machine: Feroceon-KW | |
| Using UBoot passing parameters structure | |
| Memory policy: ECC disabled, Data cache writeback | |
| Built 1 zonelists in Zone order, mobility grouping off. Total pages: 65024 | |
| Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none | |
| PID hash table entries: 1024 (order: 10, 4096 bytes) | |
| Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | |
| Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | |
| Memory: 256MB = 256MB total | |
| Memory: 246272KB available (4960K code, 334K data, 136K init, 0K highmem) | |
| Hierarchical RCU implementation. | |
| NR_IRQS:128 | |
| Console: colour dummy device 80x30 | |
| Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120) | |
| Mount-cache hash table entries: 512 | |
| CPU: Testing write buffer coherency: ok | |
| NET: Registered protocol family 16 | |
| Feroceon L2: Enabling L2 | |
| Feroceon L2: Cache support initialised. | |
| CPU Interface | |
| ------------- | |
| SDRAM_CS0 ....base 00000000, size 256MB | |
| SDRAM_CS1 ....disable | |
| SDRAM_CS2 ....disable | |
| SDRAM_CS3 ....disable | |
| PEX0_MEM ....base e0000000, size 128MB | |
| PEX0_IO ....base f2000000, size 1MB | |
| PEX1_MEM ....no such | |
| PEX1_IO ....no such | |
| INTER_REGS ....base f1000000, size 1MB | |
| NFLASH_CS ....base fa000000, size 2MB | |
| SPI_CS ....base f4000000, size 16MB | |
| BOOT_ROM_CS ....no such | |
| DEV_BOOTCS ....no such | |
| CRYPT_ENG ....base f0000000, size 2MB | |
| Marvell Development Board (LSP Version KW_LSP_5.1.3_patch29)-- DB-88F6702A-BP Soc: 88F6702 A1 LE | |
| Detected Tclk 166666667 and SysClk 400000000 | |
| MV Buttons Device Load | |
| Marvell USB EHCI Host controller #0: c8040740 | |
| PEX0 interface detected no Link. | |
| PCI: bus0: Fast back to back transfers enabled | |
| mvPexLocalBusNumSet: ERR. Invalid PEX interface 1 | |
| bio: create slab <bio-0> at 0 | |
| SCSI subsystem initialized | |
| usbcore: registered new interface driver usbfs | |
| usbcore: registered new interface driver hub | |
| usbcore: registered new device driver usb | |
| NET: Registered protocol family 2 | |
| IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | |
| TCP established hash table entries: 8192 (order: 4, 65536 bytes) | |
| TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | |
| TCP: Hash tables configured (established 8192 bind 8192) | |
| TCP reno registered | |
| NET: Registered protocol family 1 | |
| Trying to unpack rootfs image as initramfs... | |
| rootfs image is not initramfs (no cpio magic); looks like an initrd | |
| Freeing initrd memory: 1708K | |
| RTC has been updated!!! | |
| rtc mv_rtc: rtc core: registered kw-rtc as rtc0 | |
| RTC registered | |
| cpufreq: Init kirkwood cpufreq driver | |
| XOR registered 4 channels | |
| XOR 2nd invalidate WA enabled | |
| cesadev_init(c000ed5c) | |
| mvCesaInit: sessions=640, queue=64, pSram=f0000000 | |
| MV Buttons Driver Load | |
| VFS: Disk quotas dquot_6.5.2 | |
| Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) | |
| squashfs: version 4.0 (2009/01/31) Phillip Lougher | |
| Installing knfsd (copyright (C) 1996 okir@monad.swb.de). | |
| NTFS driver 2.1.29 [Flags: R/O]. | |
| JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. | |
| fuse init (API version 7.12) | |
| msgmni has been set to 484 | |
| alg: No test for cipher_null (cipher_null-generic) | |
| alg: No test for ecb(cipher_null) (ecb-cipher_null) | |
| alg: No test for digest_null (digest_null-generic) | |
| alg: No test for compress_null (compress_null-generic) | |
| alg: No test for lzma (lzma-generic) | |
| alg: No test for stdrng (krng) | |
| alg: No test for hmac(digest_null) (hmac(digest_null-generic)) | |
| Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) | |
| io scheduler noop registered | |
| io scheduler anticipatory registered (default) | |
| Initializing ths8200_init | |
| Initializing dove_adi9889_init | |
| Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled | |
| serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A | |
| console [ttyS0] enabled | |
| serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A | |
| brd: module loaded | |
| loop: module loaded | |
| Integrated Sata device found | |
| IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs | |
| scsi0 : Marvell SCSI to SATA adapter | |
| scsi1 : Marvell SCSI to SATA adapter | |
| Loading Marvell Ethernet Driver: | |
| o Cached descriptors in DRAM | |
| o DRAM SW cache-coherency | |
| o 2 Giga ports supported | |
| o Single RX Queue support - ETH_DEF_RXQ=0 | |
| o Single TX Queue support - ETH_DEF_TXQ=0 | |
| o TCP segmentation offload (TSO) supported | |
| o Large Receive offload (LRO) supported | |
| o Receive checksum offload supported | |
| o Transmit checksum offload supported | |
| o Network Fast Processing (Routing) supported - (Disabled) | |
| o Driver ERROR statistics enabled | |
| o Proc tool API enabled | |
| o SKB Reuse supported - (Disabled) | |
| o SKB Recycle supported - (Disabled) | |
| o Rx descripors: q0=128 | |
| o Tx descripors: q0=532 | |
| o Loading network interface(s): | |
| o register under mv88fx_eth platform | |
| o egiga0, ifindex = 2, GbE port = 0 | |
| Warning: Giga 1 is Powered Off | |
| mvFpRuleDb (c0ee4000): 2048 entries, 8192 bytes | |
| Counter=0, opIdx=6, overhead=16 | |
| Counter=1, opIdx=2, overhead=0 | |
| Counter=2, opIdx=1, overhead=18 | |
| Counter=3, opIdx=2, overhead=0 | |
| NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) | |
| Scanning device for bad blocks | |
| Using static partition definition | |
| Creating 7 MTD partitions on "nand_mtd": | |
| 0x000000000000-0x000000100000 : "u-boot" | |
| 0x000000100000-0x000000600000 : "uImage" | |
| 0x000000600000-0x000000b00000 : "ramdisk" | |
| 0x000000b00000-0x000006f00000 : "image" | |
| 0x000006f00000-0x000007900000 : "rescue firmware" | |
| 0x000007900000-0x000007e00000 : "config" | |
| 0x000007e00000-0x000008000000 : "my-dlink" | |
| ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver | |
| ehci_marvell ehci_marvell.70059: Marvell Orion EHCI | |
| ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 | |
| ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 | |
| ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 | |
| usb usb1: configuration #1 chosen from 1 choice | |
| hub 1-0:1.0: USB hub found | |
| hub 1-0:1.0: 1 port detected | |
| ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver | |
| uhci_hcd: USB Universal Host Controller Interface driver | |
| Initializing USB Mass Storage driver... | |
| usbcore: registered new interface driver usb-storage | |
| USB Mass Storage support registered. | |
| mice: PS/2 mouse device common for all mice | |
| i2c /dev entries driver | |
| md: linear personality registered for level -1 | |
| md: raid0 personality registered for level 0 | |
| md: raid1 personality registered for level 1 | |
| device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com | |
| usbcore: registered new interface driver usbhid | |
| usbhid: v2.6:USB HID core driver | |
| TCP cubic registered | |
| NET: Registered protocol family 17 | |
| RPC: Registered udp transport module. | |
| RPC: Registered tcp transport module. | |
| rtc mv_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) | |
| md: Waiting for all devices to be available before autodetect | |
| md: If you don't use raid, use raid=noautodetect | |
| md: Autodetecting RAID arrays. | |
| md: Scanned 0 and added 0 devices. | |
| md: autorun ... | |
| md: ... autorun DONE. | |
| RAMDISK: gzip image found at block 0 | |
| VFS: Mounted root (ext2 filesystem) on device 1:0. | |
| Freeing init memory: 136K | |
| init started: BusyBox v1.20.2 (2016-01-27 17:36:49 CST) | |
| starting pid 536, tty '': '/etc/rc.sh' | |
| ** Mounting /etc/fstab | |
| umount: can't umount /proc: Invalid argument | |
| umount: can't umount /usr/local/modules: Invalid argument | |
| sh: can't open '/usr/sbin/pre_usb.sh' | |
| first good block is 0 | |
| image len = 40693760 , image checksum = f602740 | |
| umount: can't umount /usr/local/tmp: Invalid argument | |
| dump image checksum=f602740 | |
| mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules | |
| ln: /lib/./libnss_dns-2.8.so: File exists | |
| ln: /lib/./libnss_dns.so.2: File exists | |
| ln: /usr/sbin/./system_init: File exists | |
| hardware init | |
| GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1 | |
| mtd check v1.02.08062012 | |
| config mtd type is JFFS2 | |
| /usr/local/config free size is 4722688 | |
| ** copy config files | |
| usbcore: registered new interface driver usblp | |
| ** set loopback interface | |
| old firmware ver:20170111 | |
| new firmware ver:20170111 | |
| first good block is 0 | |
| mac1 = AC:F1:DF:10:xx:xx | |
| lan0:ifconfig egiga0 hw ether AC:F1:DF:10:xx:xx | |
| egiga0: mac address changed | |
| egiga0: started | |
| Support Mydlink | |
| NET: Registered protocol family 10 | |
| lo: Disabled Privacy Extensions | |
| ADDRCONF(NETDEV_UP): egiga0: link is not ready | |
| IPv6 over IPv4 tunneling driver | |
| sit0: Disabled Privacy Extensions | |
| ip6tnl0: Disabled Privacy Extensions | |
| IPv4 over IPv4 tunneling driver | |
| tunl0: Disabled Privacy Extensions | |
| net.ipv6.conf.default.accept_dad = 2 | |
| net.ipv6.conf.egiga0.accept_dad = 2 | |
| net.ipv6.conf.default.dad_transmits = 1 | |
| net.ipv6.conf.egiga0.dad_transmits = 1 | |
| net.ipv6.conf.default.forwarding = 0 | |
| net.ipv6.conf.default.accept_redirects = 1 | |
| *** execute rc.init.sh | |
| awk: /var/run/udhcpc0.pid: No such file or directory | |
| RTNETLINK answers: Cannot assign requested address | |
| route: SIOCDELRT: No such process | |
| killall: crond: no process killed | |
| rtc: RTC time = 2017/5/28 Sun 14:10:33 | |
| *** set Time Zone **** | |
| Sun May 28 14:10:33 CEST 2017 | |
| *** get Time from rtc and set it into system **** | |
| rtc: RTC time = 2017/5/28 Sun 14:10:34 | |
| Sun May 28 16:10:34 CEST 2017 | |
| *** Do not adjust RTC time *** | |
| Module IPC SERVER Version:(1.00.20090706) | |
| ads=0 | |
| created mail daemon thread 0 | |
| /usr/sbin/system_init: line 487: op_server: not found | |
| Starting system message bus | |
| Command: wget -T5 -t3 -q http://cfaj.freeshell.org/ipaddr.cgi -O /tmp/exip.0 | |
| LLTDIF= egiga0 | |
| Command: wget -T5 -t3 -q http://icanhazip.com/ -O /tmp/exip.1 | |
| Stop NFS Deamon.... | |
| Stop NFS mountd.... | |
| Unload Driver.... | |
| Stop Portmap. | |
| No NFS information . | |
| Stop NFS Server OVER. | |
| Start config the NFS needed file.... | |
| Config Over. | |
| No NFS information . | |
| Start portmap.... | |
| Load Driver . | |
| Start NFS Deamon . | |
| svc: failed to register lockdv1 RPC service (errno 97). | |
| NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory | |
| NFSD: unable to find recovery directory /var/lib/nfs/v4recovery | |
| NFSD: starting 90-second grace period | |
| Start NFS Server OVER . | |
| Command: wget -T5 -t3 -q http://ifconfig.me/ip -O /tmp/exip.2 | |
| Command: wget -T5 -t3 -q http://whatismyip.org/ -O /tmp/exip.3 | |
| Command: wget -T5 -t3 -q http://ifconfig.me/ip -O /tmp/exip.4 | |
| Command: wget -T5 -t3 -q http://checkip.dyndns.com:8245/ -O /tmp/exip.5 | |
| Illegal instruction | |
| enable ssh server | |
| cp: can't stat '/usr/local/config/Mydlink_Status.xml': No such file or directory | |
| mcu version 1.02 | |
| system daemon v1.03.20130707 | |
| killall: chk_hotplug: no process killed | |
| chk_io v1.03.20130502 | |
| killall: smbd: no process killed | |
| mfg_start version 1.00(2017-01-11) | |
| Sun May 28 16:12:00 2017 | |
| usb_dir [] | |
| cp: can't stat '/usr/local/config/mydlink_time.xml': No such file or directory | |
| 2017-05-28 16:11:58: (../../src/log.c.166) server started | |
| sh: you need to specify whom to kill | |
| killall: dcp: no process killed | |
| killall: signalc: no process killed | |
| killall: upnpc-ddns: no process killed | |
| starting pid 1919, tty '/dev/ttyS0': '/bin/login' | |
| Password of admin: killall: tsa: no process killed | |
| opt.local stop ok. | |
| opt.local start ok. | |
| usb_dir [/] | |
| filename_mfg mfg_DNS_320LW | |
| check //mfg_DNS_320LW file | |
| open //mfg_DNS_320LW file failed | |
| LED_POWER_ON | |
| Login incorrect | |
| Password of admin: | |
| BusyBox v1.20.2 (2016-01-27 17:36:49 CST) built-in shell (ash) | |
| Enter 'help' for a list of built-in commands. | |
| / # | |
| / # | |
| / # | |
| / # | |
| / # | |
| / # reboot | |
| The system is going down NOW! | |
| Sent SIGTERM to all processes | |
| Block size total free used max | |
| ---------- ----- ----- ----- ----- | |
| 2^001 0 0 0 0 | |
| 2^002 0 0 0 0 | |
| 2^003 0 0 0 0 | |
| 2^004 0 0 0 0 | |
| 2^005 0 0 0 0 | |
| 2^006 0 0 0 0 | |
| 2^007 0 0 0 0 | |
| 2^008 0 0 0 0 | |
| 2^009 0 0 0 0 | |
| 2^010 0 0 0 0 | |
| 2^011 0 0 0 0 | |
| 2^012 0 0 0 0 | |
| 2^013 0 0 0 0 | |
| 2^014 0 0 0 0 | |
| 2^015 0 0 0 0 | |
| 2^016 0 0 0 0 | |
| 2^017 0 0 0 0 | |
| 2^018 0 0 0 0 | |
| 2^019 0 0 0 0 | |
| 2^020 0 0 0 0 | |
| 2^021 0 0 0 0 | |
| 2^022 0 0 0 0 | |
| 2^023 0 0 0 0 | |
| ------------------------------------------ | |
| total size : 0 bytes | |
| free size : 0 bytes | |
| used size : 0 bytes | |
| !!! Module IPC Terminated !!! | |
| !!! AND Server Terminated !!! | |
| 2017-05-28 16:12:30: (../../src/server.c.1512) server stopped by UID = 0 PID = 1 | |
| ../../src/lighttpd-angel.c.140: child (pid=1822) exited normally with exitcode: 0 | |
| Block size total free used max | |
| ---------- ----- ----- ----- ----- | |
| 2^001 0 0 0 0 | |
| 2^002 0 0 0 0 | |
| 2^003 192 192 0 187 | |
| 2^004 24 24 0 22 | |
| 2^005 56 56 0 56 | |
| 2^006 344 344 0 342 | |
| 2^007 0 0 0 0 | |
| 2^008 0 0 0 0 | |
| 2^009 0 0 0 0 | |
| 2^010 0 0 0 0 | |
| 2^011 8 8 0 1 | |
| 2^012 0 0 0 0 | |
| 2^013 0 0 0 0 | |
| 2^014 0 0 0 0 | |
| 2^015 0 0 0 0 | |
| 2^016 0 0 0 0 | |
| 2^017 0 0 0 0 | |
| 2^018 0 0 0 0 | |
| 2^019 0 0 0 0 | |
| 2^020 0 0 0 0 | |
| 2^021 0 0 0 0 | |
| 2^022 0 0 0 0 | |
| 2^023 0 0 0 0 | |
| ------------------------------------------ | |
| total size : 42112 bytes | |
| free size : 42112 bytes | |
| used size : 0 bytes | |
| Sent SIGKILL to all processes | |
| md: stopping all md devices. | |
| Restarting system. | |
| Reseting !! | |
| -> Not rebooting, now hot enough for the stupid Weltrend WT69P3 chip to prohibit the main CPU to boot (I suppose) .. |
Did you have success with debugging this?
I had no time for this yet :(
And I don't know how I'd solder the WT69P3 chip UART (or whatever it is ?), because the holes are really thin and I don't have the adapted equipment. I'm not even sure the holes are wired.
Also tried to solder the serial port. Reading the boot output worked, but stopping by pressing keys didn't (I am suspecting, that my soldering joint wasn't good).
You mean stopping uboot ? I haven't tried this (and I know this can be disabled, I don't know about this one).
I had some difficulties with soldering too, too weak soldering iron (15W ..), could only solder RX & TX, I got GND from the fan connector :]
As for the blue blinking issue, it didn't even output anything on the serial port when it blinked and didn't boot.
Then I put the sole board into the oven, 220°C for 20 minutes and the problem is gone! :)
I'm not sure what you mean here ? Blinking + no boot & no output => thermal sensor issue right ?
So you managed to fix it by ~resoldering in oven, is that it ?
Btw there's no notifications for Gists, so you can continue by email (or just ping to keep this public) if you want.
Then I put the sole board into the oven, 220°C for 20 minutes and the problem is gone! :)
Did this solved the thermal sensor issue?
Did this solved the thermal sensor issue?
It seems from the message, my attempt with this was however a failure (not hot enough? Not enough time? I've never done this before), but I just saw that this thread is giving useful advises: http://forums.dlink.com/index.php?topic=55647.15
Also, https://pop.fsck.pl/hardware/dns-320l.html gives more informations on the Weltrend WT69P3 (I'm still hoping to play with it one day).
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Did you have success with debugging this? I have bought one of those second hand, found that it had the problem, worked around it by putting it into the fridge.
Also tried to solder the serial port. Reading the boot output worked, but stopping by pressing keys didn't (I am suspecting, that my soldering joint wasn't good). As for the blue blinking issue, it didn't even output anything on the serial port when it blinked and didn't boot.
Then I put the sole board into the oven, 220°C for 20 minutes and the problem is gone! :)