T95_SerialBootOutput.txt

[194]HELLO! SBOOT is starting!
[197]sboot commit : d1e4f83e
[200]set pll start
[202]periph0 has been enabled
[205]set pll end
[207]unknow PMU
[209]unknow PMU
[211]PMU: AXP1530
[213]dram return write ok
[215]board init ok
[217]try to probe rtc region
[220]DRAM BOOT DRIVE INFO: V0.649
[223]the chip id is 0x5000
[226]chip id check OK
[230]DRAM_VCC set to 1500 mv
[233]DRAM CLK =600 MHZ
[235]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4)
[243]Actual DRAM SIZE =4096 M
[246]DRAM SIZE =4096 MBytes, para1 = 310b, para2 = 10000000, dram_tpr13 = 6041
[255]DRAM simple test OK.
[257]rtc standby flag is 0x0, super standby flag is 0x0
[263][mmc]: mmc driver ver 2021-10-12 13:56
[267][mmc]: b mmc 2 bias 0
[275][mmc]: Wrong media type 0x0, but host sdc2, try mmc first
[281][mmc]: ***Try MMC card 2***
[313]mmc_read_info 1138:region magic is not right, retry more time 0
[331]mmc_read_info 1138:region magic is not right, retry more time 0
[348]mmc_read_info 1138:region magic is not right, retry more time 0
[365]mmc_read_info 1138:region magic is not right, go err 0
[371]dump info registers:[373]
0x36ba4 : [375]0 [376]0 [376]0 [377]0 [378]
[378][mmc]: RMCA FAIL!
[380][mmc]: mmc read timing info fail
[384][mmc]: wrong freq 2 at spd md 2
[388][mmc]: force 25m
[391][mmc]: MMC 4.5
[393][mmc]: HSSDR52/SDR25 8 bit
[396][mmc]: 25000000 Hz
[398][mmc]: 29820 MB
[400][mmc]: ***SD/MMC 2 init OK!!!***
[518]read toc1 from emmc 32800 sector
[521]OLD version: 0.0
[523]NEW version: 0.0
[599]load rotpk hash
[663]load monitor-key hash
[665]load monitor hash
[870]load boot-key hash
[872]load boot hash
[938]load vbmeta-key hash
[940]load vbmeta hash
[1008]load recovery-key hash
[1011]load recovery hash
[1014]monitor entry=0x48000000
[1017]uboot entry=0x4a000000
[1020]optee entry=0x48600000
[1023]mmc not para
[1027]run out of boot0
NOTICE:  BL3-1: v1.0(debug):be96482
NOTICE:  BL3-1: Built : 18:32:32, 2021-04-21
NOTICE:  BL3-1 commit: 8
NOTICE:  cpuidle init version V1.0
NOTICE:  secure os exist
MESSAGE: [0x0] TEE-CORE: OP-TEE version: 5c40397e #1 Tue Feb  2 07:45:37 UTC 2021 arm
NOTICE:  BL3-1: Preparing for EL3 exit to normal world
NOTICE:  BL3-1: Next image address = 0x4a000000
NOTICE:  BL3-1: Next image spsr = 0x1d3


U-Boot 2018.05 (Jun 22 2022 - 11:19:57 +0800) Allwinner Technology

[01.119]CPU:   Allwinner Family
[01.122]Model: sun50iw9
I2C:   ready
[01.126]DRAM:  2 GiB
[01.129]Relocation Offset is: 75ec5000
[01.168]secure enable bit: 1
[01.171]pmu_axp152_probe pmic_bus_read fail
[01.175]PMU: AXP1530
[01.181]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=400Mhz
[01.189]drv_disp_init
[01.218]__clk_enable: clk is null.
[01.224]drv_disp_init finish
[01.227]gic: sec monitor mode
[01.254]flash init start
[01.256]workmode = 0,storage type = 2
[01.260]MMC:     2
[01.261]get mem for descripter OK !
[01.270]get sdc2 sdc_boot0_sup_1v8 fail.
[01.275]io is 1.8V

[01.310]rto or no error or software timeout,no need retry
[01.317]already at HSSDR52_SDR25 mode
[02.234]speed mode: HSSDR52/SDR25
[02.237]---400000Hz:
[02.239]--best 255
[02.241]---25000000Hz:
[02.243]--best 255
[02.245]---50000000Hz:
[02.247]--best 22
[02.249]already at HSSDR52_SDR25 mode
[02.252]already at HSSDR52_SDR25 mode
[02.256]sunxi flash init ok
[02.259]Loading Environment from SUNXI_FLASH... OK
secure storage read hdcpkey fail
[02.273]secure storage read hdcpkey fail with:-1
secure storage read widevine fail
[02.280]secure storage read widevine fail with:-1
[02.286]usb burn from boot
delay time 0
weak:otg_phy_config
[02.299]usb prepare ok
[03.102]overtime
[03.106]do_burn_from_boot usb : no usb exist
[03.110]boot_gui_init:start
FAT: Misaligned buffer address (bbe7e678)
32 bytes read in 4 ms (7.8 KiB/s)
[03.393]boot_gui_init:finish
[03.396]bmp_name=bootlogo.bmp
2764922 bytes read in 60 ms (43.9 MiB/s)
[03.477]get max-frequency ok 100000000 Hz
[03.481]1 1 1: 1 1 1
[03.483]delete mmc-hs400-1_8v from dtb
[03.486]delete mmc-hs200-1_8v from dtb
[03.490]delete mmc-ddr-1_8v from dtb
[03.493]get max-frequency ok 50000000 Hz
[03.506]update dts
** Unrecognized filesystem type **
[03.517]load file(ULI/factory/rootwait init.txt) error.
** Unrecognized filesystem type **
[03.531]load file(ULI/factory/snum.txt) error.
[03.535]name in map mac
** Unrecognized filesystem type **
[03.547]load file(ULI/factory/wifi_mac.txt) error.
** Unrecognized filesystem type **
[03.561]load file(ULI/factory/bt_mac.txt) error.
** Unrecognized filesystem type **
[03.575]load file(ULI/factory/selinux.txt) error.
** Unrecognized filesystem type **
[03.588]load file(ULI/factory/specialstr.txt) error.
[03.600]update part info
[03.624]update bootcmd
[03.626]No ethernet found.
Hit any key to stop autoboot:  0
[04.133]not supported key
[04.135]actual n size:1000, e:10001
[04.138]exptect n size:800, e:10001
show hash of file
9c 4f 9a 0a a2 d1 89 50 66 7d 92 6a 19 a1 ac 18
ff 0d 01 83 43 4f 99 3f e3 3c eb 1e 68 c1 3d 03

image vbmeta hash valid
[04.154]image_len not match, actual:19466240, expected:19234816
[04.159]bmp_name=red_warning.bmp
** Unable to read file red_warning.bmp **
[04.167]sunxi bmp info error : unable to open logo file red_warning.bmp
[34.176]mmc exit start
[34.211]mmc 2 exit ok