Strong 1200 logs

00_OEM_bootlog

===================================================================
     		MT7621   stage1 code Mar 12 2015 14:43:30 (ASIC)
     		CPU=500000000 HZ BUS=166666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x31100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-800Mhz ===
PLL2 FB_DL: 0xa, 1/0 = 615/409 29000000
PLL4 FB_DL: 0xa, 1/0 = 565/459 29000000
PLL3 FB_DL: 0x15, 1/0 = 608/416 55000000
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
      --------------------------------------------------------------------------------
0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    1    1    1
000F:|    0    0    0    0    0    1    1    1    1    1    1    1    1    1    1    1
0010:|    1    1    1    1    1    1    1    1    1    1    1    1    0    0    0    0
0011:|    1    1    1    1    1    0    0    0    0    0    0    0    0    0    0    0
0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
DRAMC_DQSCTL1[0e0]=14000000
DRAMC_DQSGCTL[124]=80000000
rank 0 coarse = 16
rank 0 fine = 48
B:|    0    0    0    0    0    0    0    0    0    1    1    1    0    0    0    0
opt_dle value:10
DRAMC_DDR2CTL[07c]=C287222D
DRAMC_PADCTL4[0e4]=000022B3
DRAMC_DQIDLY1[210]=0E0E0B0D
DRAMC_DQIDLY2[214]=0A0C0A0C
DRAMC_DQIDLY3[218]=0E0B0C0A
DRAMC_DQIDLY4[21c]=0E0A0F0B
DRAMC_R0DELDLY[018]=00002C2C
==================================================================
		RX	DQS perbit delay software calibration 
==================================================================
1.0-15 bit dq delay value
==================================================================
bit|     0  1  2  3  4  5  6  7  8  9
--------------------------------------
0 |    11 10 13 13 11 10 11 10 9 11 
10 |    10 11 11 13 10 13 
--------------------------------------

==================================================================
2.dqs window
x=pass dqs delay value (min~max)center 
y=0-7bit DQ of every group
input delay:DQS0 =44 DQS1 = 44
==================================================================
bit	DQS0	 bit      DQS1
0  (1~84)42  8  (2~85)43
1  (1~86)43  9  (1~85)43
2  (1~85)43  10  (1~85)43
3  (1~86)43  11  (1~82)41
4  (1~86)43  12  (2~86)44
5  (1~87)44  13  (1~84)42
6  (1~85)43  14  (1~87)44
7  (1~88)44  15  (1~85)43
==================================================================
3.dq delay value last
==================================================================
bit|    0  1  2  3  4  5  6  7  8   9
--------------------------------------
0 |    13 11 14 14 12 10 12 10 10 12 
10 |    11 14 11 15 10 14 
==================================================================
==================================================================
     TX  perbyte calibration 
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000 
dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1 
dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2 
DQ loop=15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=15,  finish count=1 
dqs_perbyte_dly.last_dqdly_pass[1]=15,  finish count=2 
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,8)
DRAMC_DQODLY1[200]=88888888
DRAMC_DQODLY2[204]=88888888
20,data:88
[EMI] DRAMC calibration passed

===================================================================
     		MT7621   stage1 code done 
     		CPU=500000000 HZ BUS=166666666 HZ
===================================================================


U-Boot 1.1.3 (Aug 12 2015 - 14:27:48)

Board: Ralink APSoC DRAM:  128 MB
relocate_code Pointer at: 87fb8000

Config XHCI 40M PLL 
******************************
Software System Reset Occurred
******************************
flash manufacture id: c2, device id 20 18
find flash: MX25L12805D
============================================ 
Ralink UBoot Version: 4.3.0.0
-------------------------------------------- 
ASIC MT7621A SingleCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection 
DRAM_TYPE: DDR3 
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Aug 12 2015  Time:14:27:48
============================================ 
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768 

 ##### The CPU freq = 880 MHZ #### 
 estimate memory size =128 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 
 0 
   
3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   WR1201_8_128
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    7295340 Bytes =  7 MB
   Load Address: 80001000
   Entry Point:  8000f500
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000f500) ...
## Giving linux memsize in MB, 128

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (root@linux-qoyc) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1486 SMP Tue Nov 29 18:11:51 CST 2016

 The CPU feqenuce set to 880 MHz
GCMP present
CPU revision is: 0001992f (MIPS 1004Kc)
Software DMA cache coherency
Determined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
avail: cpu2 is not ready
avail: cpu3 is not ready
Detected 1 available secondary CPU(s)
PERCPU: Embedded 7 pages/cpu @81103000 s6464 r8192 d14016 u65536
pcpu-alloc: s6464 r8192 d14016 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS1,57600 root=/dev/ram0 rootfstype=squashfs,jffs2
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Writing ErrCtl register=00011580
Readback ErrCtl register=00011580
Memory: 118124k/131072k available (4723k kernel code, 12948k reserved, 1682k data, 5040k init, 0k highmem)
Hierarchical RCU implementation.
	Verbose stalled-CPUs detection is disabled.
NR_IRQS:128
Trying to install interrupt handler for IRQ24
Trying to install interrupt handler for IRQ25
Trying to install interrupt handler for IRQ22
Trying to install interrupt handler for IRQ9
Trying to install interrupt handler for IRQ10
Trying to install interrupt handler for IRQ11
Trying to install interrupt handler for IRQ12
Trying to install interrupt handler for IRQ13
Trying to install interrupt handler for IRQ14
Trying to install interrupt handler for IRQ16
Trying to install interrupt handler for IRQ17
Trying to install interrupt handler for IRQ18
Trying to install interrupt handler for IRQ19
Trying to install interrupt handler for IRQ20
Trying to install interrupt handler for IRQ21
Trying to install interrupt handler for IRQ23
Trying to install interrupt handler for IRQ26
Trying to install interrupt handler for IRQ27
Trying to install interrupt handler for IRQ28
Trying to install interrupt handler for IRQ15
Trying to install interrupt handler for IRQ8
Trying to install interrupt handler for IRQ29
Trying to install interrupt handler for IRQ30
Trying to install interrupt handler for IRQ31
console [ttyS1] enabled
Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
launch: starting cpu1
launch: cpu1 gone!
CPU revision is: 0001992f (MIPS 1004Kc)
Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
Brought up 2 CPUs
Synchronize counters across 2 CPUs: done.
NET: Registered protocol family 16
release PCIe RST: RALINK_RSTCTRL = 7000000
PCIE PHY initialize
***** Xtal 40MHz *****
start MT7621 PCIe register access
RALINK_RSTCTRL = 7000000
RALINK_CLKCFG1 = 77ffeff8

*************** MT7621 PCIe RC mode *************
PCIE2 no card, disable it(RST&CLK)
pcie_link status = 0x3
RALINK_RSTCTRL= 3000000
*** Configure Device number setting of Virtual PCI-PCI bridge ***
RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
PCIE0 enabled
PCIE1 enabled
interrupt enable status: 300000
Port 1 N_FTS = 1b105000
Port 0 N_FTS = 1b105000
config reg done
init_rt2880pci done
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x60400000-0x6040ffff] (PCI address [0x60400000-0x6040ffff]
pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
pci 0000:00:01.0: BAR 1: set to [mem 0x60410000-0x6041ffff] (PCI address [0x60410000-0x6041ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff 64bit] (PCI address [0x60200000-0x602fffff]
pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 02-02]
pci 0000:00:01.0:   bridge window [io  disabled]
pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60400000
res[1]->end = 6040ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
res[0]->start = 0
res[0]->end = 0
res[1]->start = 60410000
res[1]->end = 6041ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0, irq=0x4
res[0]->start = 60000000
res[0]->end = 600fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x2, slot = 0x1, irq=0x18
res[0]->start = 60200000
res[0]->end = 602fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay(lpj = 1167360)
Load Ralink Timer0 Module
Load Ralink Timer1 Module
Load Ralink Timer2 Module
fuse init (API version 7.15)
msgmni has been set to 230
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
lp: driver loaded but no devices found
set_gpio_type: id[23] type[0]
set_gpio_type: id[22] type[0]
set_gpio_type: id[25] type[1]

init_MTC_private_led OK
Ralink gpio driver initialized
Enable Ralink HS_DMA Controller Module 
reg_int_mask=0, INT_MASK= 10000 
HSDMA_init function 

phy_tx_ring0 = 0x07d48000, tx_ring0 = 0xa7d48000

phy_rx_ring0 = 0x07d49000, rx_ring0 = 0xa7d49000
TX_CTX_IDX0 = 0
TX_DTX_IDX0 = 0
RX_CRX_IDX0 = ff
RX_DRX_IDX0 = 0
HSDMA_GLO_CFG = 475
Enable Ralink GDMA Controller Module 
GDMA IP Version=3
spidrv_major = 217
i2cdrv_major = 218
spdif_mod_init: start SPDIF module
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
brd: module loaded
flash manufacture id: c2, device id 20 18
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000ff0000 : "Kernel"
0x000000ff0000-0x000001000000 : "Second_Config"
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880ad
Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288003
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
IMQ driver loaded successfully.
	Hooking IMQ before NAT on PREROUTING.
	Hooking IMQ after NAT on POSTROUTING.
usbcore: registered new interface driver catc
catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
usbcore: registered new interface driver asix
usbcore: registered new interface driver ax88179_178a
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
register rt2860


=== pAd = c0282000, size = 2173440 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0180000, csr_addr=0xc0180000!
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=3
NVM is efuse and the information is too less to bring up the interface
Force to use Flash mode
NVM is FLASH mode (pAd->flash_offset = 0x48000)
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai


=== pAd = c0602000, size = 2173440 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xc0500000, csr_addr=0xc0500000!
device_id =0x7662
==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=3
NVM is efuse and the information is too less to bring up the interface
Force to use Flash mode
NVM is FLASH mode (pAd->flash_offset = 0x40000)
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 0(0x00000000)
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1
xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
xhc_mtk xhc_mtk: xHCI Host Controller
xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1845 buckets, 7380 max)
matchsize=264
xt_time: kernel timezone is -0000
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
>>>wsc_negotiate_info_init:r[0]<<<
>>>private_domain_init:r[0]<<<
Warning: unable to open an initial console.
Freeing unused kernel memory: 5040k freed
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
     __   ___  _____  _____   _  _______ ______  _____  _   ___
    |  \ /   ||  ___||  __ \ | ||  __  ||__  __||  ___|| | /  /
    |   ^    || |__  | |  \ \| || |  | |  | |   | |__  | |/  /
    |  | |   ||  ___|| |  | || || |__| |  | |   |  ___||    \
    |  | |   || |___ | |__/ /| ||  __  |  | |   | |___ | |\  \
    |__| |___||_____||_____/ |_||_|  |_|  |_|   |_____||_| \__\

		        = Everyday Genius =
		            
Give root password for system maintenance
(or type Control-D for normal startup):

Have a lot of fun...

Password for 'admin' changed
>>>chpasswd_root<<<
iptables>>>PRIVATE_DOMAIN_IOCTL_SET g_sz_private_domain=strong.1200.wr<<<
 v1.4.10: 
The "nat" table is not intended for filtering, the use of DROP is therefore inhibited.


Try `iptables -h' or 'iptables --help' for more information.
>>>PRIVATE_DOMAIN_IOCTL_GET g_sz_private_domain=strong.1200.wr<<<
>>>kernel_private_domain = strong.1200.wr<<<
==>dnsProxyInit...
==>filterInit...
==>natFunctionInit...
==>firewallFunctionInit...
==>qosInit...
==>systoolServiceInit...
==>IPTVServiceInit...
==>staticRouteFunctionInit...
Raeth v3.1 (Tasklet)
phy_free_head is 0x5e00000!!!
phy_free_tail_phy is 0x5e01ff0!!!
txd_pool=a5e02000 phy_txd_pool=05E02000
ei_local->skb_free start address is 0x87ce9494.
free_txd: a5e02010, ei_local->cpu_ptr: 05E02000
 POOL  HEAD_PTR | DMA_PTR | CPU_PTR 
----------------+---------+--------
     0xa5e02000 0x05E02000 0x05E02000

phy_qrx_ring = 0x05df9000, qrx_ring = 0xa5df9000

phy_rx_ring0 = 0x05e04000, rx_ring0 = 0xa5e04000
change HW-TRAP to 0x17ccf
set LAN/WAN LLLLW
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x43288003
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
ra2880stop()...Done
Free TX/RX Ring Memory!
Raeth v3.1 (Tasklet)
phy_free_head is 0x5d30000!!!
phy_free_tail_phy is 0x5d31ff0!!!
txd_pool=a5d32000 phy_txd_pool=05D32000
ei_local->skb_free start address is 0x87ce9494.
free_txd: a5d32010, ei_local->cpu_ptr: 05D32000
 POOL  HEAD_PTR | DMA_PTR | CPU_PTR 
----------------+---------+--------
     0xa5d32000 0x05D32000 0x05D32000

phy_qrx_ring = 0x05d49000, qrx_ring = 0xa5d49000

phy_rx_ring0 = 0x05d34000, rx_ring0 = 0xa5d34000
change HW-TRAP to 0x17ccf
set LAN/WAN LLLLW
GMAC1_MAC_ADRH -- : 0x00000016
GMAC1_MAC_ADRL -- : 0xfbc6a38e
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
ifconfig: SIOCSIFHWADDR: Device or resource busy
device eth2 entered promiscuous mode
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, valudevice eth2.1 entered promiscuous mode
e=10002
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
br0: port 1(eth2.1) entering learning state
br0: port 1(eth2.1) entering learning state
Unable to open /etc/udhcpd.leases for reading

ReStart wireless Now
br0: port 1(eth2.1) entering forwarding state
ESW: Link Status Changed - Port0 Link UP
>>webdir[/etc_ro/web_root]
>>websDefaultPage[main.asp]
build time = 
20141115060606a
rom patch for E3 IC

platform = 
ALPS
hw/sw version = 
��
patch version = 

FW Version:0.0.00 Build:1
Build Time:201507311614____
fw for E3 IC
RX[0] DESC a6375000 size = 4096
RX[1] DESC a6376000 size = 4096
E2pAccessMode=0
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 14
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (171)
get_chl_grp:illegal channel (171)
drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2899 assert (ad->TxPower[choffset].Channel == 42)failed
Country Region from e2p = ffff
mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=2
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=13, low_temp_slope=16
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=-7, tc_upper_bound=5
mt76x2_get_external_lna_gain::LNA type=0x10, BLNAGain=0xffffff8e, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
2. Phy Mode = 14
3. Phy Mode = 14
andes_pci_fw_init
0x1300 = 00073200
AntCfgInit: primary/secondary ant 0/1
andes_load_cr:cr_type(2)
ChipStructAssign(): MT76x2 hook !
RTMPSetPhyMode: channel is out of range, use first channel=0 
MCS Set = ff ff 00 00 01
=====================================================
Channel 1 : Dirty = 33, ApCnt=10, Busy Time = 0, Skip Channel = FALSE
Channel 2 : Dirty = 4, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
Channel 3 : Dirty = 5, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
Channel 4 : Dirty = 34, ApCnt=3, Busy Time = 0, Skip Channel = FALSE
Channel 5 : Dirty = 35, ApCnt=1, Busy Time = 0, Skip Channel = FALSE
Channel 6 : Dirty = 34, ApCnt=4, Busy Time = 0, Skip Channel = FALSE
Channel 7 : Dirty = 5, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
Channel 8 : Dirty = 5, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
Channel 9 : Dirty = 4, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
Channel 10 : Dirty = 3, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
Channel 11 : Dirty = 31, ApCnt=2, Busy Time = 0, Skip Channel = FALSE
Channel 12 : Dirty = 2, ApCnt=0, Busy Time = 0, Skip Channel = TRUE
Channel 13 : Dirty = 31, ApCnt=3, Busy Time = 0, Skip Channel = TRUE
=====================================================
Rule 2 APCnt : minimum APCnt with  minimum interference(dirtiness: 30~32) ==> Select Channel 11
 Dirtiness = 31 ,  Min ApCnt = 2
mt76x2_bbp_adjust():rf_bw=1, ext_ch=3, PrimCh=11, HT-CentCh=9, VHT-CentCh=0
APStartUp(): AP Set CentralFreq at 9(Prim=11, HT-CentCh=9, VHT-CentCh=0, BBP_BW=1)
mt76x2_calibration(channel = 9)
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
Main bssid = 00:16:fb:c6:a3:8c
mt76x2_reinit_agc_gain:original agc_vga0 = 0x44, agc_vga1 = 0x44
mt76x2_reinit_agc_gain:updated agc_vga0 = 0x44, agc_vga1 = 0x44
mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x35, hi_lna1 = 0x35
mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x35, hi_lna1 = 0x35
original vga value(chain0) = 44
original vga value(chain1) = 44
<==== rt28xx_init, Status=0
get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=apcli
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
br0: port 2(ra0) entering learning state
build time = 
20141115060606a
rom patch for E3 IC

platform = 
ALPS
hw/sw version = 
��
patch version = 

FW Version:0.0.00 Build:1
Build Time:201507311614____
fw for E3 IC
RX[0] DESC a6130000 size = 4096
RX[1] DESC a6131000 size = 4096
E2pAccessMode=0
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Not Equal!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 49
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (167)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (169)
get_chl_grp:illegal channel (171)
get_chl_grp:illegal channel (171)
drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2899 assert (ad->TxPower[choffset].Channel == 42)failed
Country Region from e2p = ffff
mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=0
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=13, low_temp_slope=16
mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=-7, tc_upper_bound=5
mt76x2_get_external_lna_gain::LNA type=0x0, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c
2. Phy Mode = 49
3. Phy Mode = 49
andes_pci_fw_init
0x1300 = 00073200
AntCfgInit: primary/secondary ant 0/1
andes_load_cr:cr_type(2)
ChipStructAssign(): MT76x2 hook !
RTMPSetPhyMode: channel is out of range, use first channel=0 
MCS Set = ff ff 00 00 00
br0: port 2(ra0) entering forwarding state
=====================================================
Channel 36 : Dirty = 32, ApCnt=1, Busy Time = 0, Skip Channel = FALSE
Channel 40 : Dirty = 2, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
Channel 44 : Dirty = 32, ApCnt=1, Busy Time = 0, Skip Channel = FALSE
Channel 48 : Dirty = 2, ApCnt=0, Busy Time = 0, Skip Channel = FALSE
=====================================================
Rule 2 APCnt : minimum APCnt with  minimum interference(dirtiness: 30~32) ==> Select Channel 36
 Dirtiness = 32 ,  Min ApCnt = 1
mt76x2_bbp_adjust():rf_bw=0, ext_ch=0, PrimCh=36, HT-CentCh=36, VHT-CentCh=42
APStartUp(): AP Set CentralFreq at 36(Prim=36, HT-CentCh=36, VHT-CentCh=42, BBP_BW=0)
mt76x2_calibration(channel = 36)
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
Main bssid = 00:16:fb:c6:b3:8c
mt76x2_reinit_agc_gain:original agc_vga0 = 0x4a, agc_vga1 = 0x4a
mt76x2_reinit_agc_gain:updated agc_vga0 = 0x4a, agc_vga1 = 0x4a
mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33
mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33
original vga value(chain0) = 4a
original vga value(chain1) = 4a
<==== rt28xx_init, Status=0
get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
RTMPDrvOpen(1):Check if PDMA is idle!
RTMPDrvOpen(2):Check if PDMA is idle!
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
device rai0 entered promiscuous mode
br0: port 3(rai0) entering learning state
br0: port 3(rai0) entering learning state

wirelessAp force reset bw
Interface doesn't accept private ioctl...
set (8BE2): Invalid argument
set_ed_chk_proc(): ed_chk=0
@@@ ed_monitor_exit : ===>
@@@ ed_monitor_exit : <===
set_ed_chk_proc(): ed_chk=1
@@@ ed_monitor_init : ===>
@@@ ed_monitor_init : <===
>>>WSC_NEGOTIATE_INFO_REG_PID program_pid=1371<<<
br0: port 3(rai0) entering forwarding state
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
parsing error file /etc/miniupnpd.config line 14 : friendly_name=Dual Band Gigabit Router 1200


create rclPrivateTimer OK

Feb  8 00:00:13 miniupnpd[1686]: HTTP listening on port 5500
Feb  8 00:00:13 miniupnpd[1686]: Listening for NAT-PMP traffic on port 5351
insmod: usbcore.ko: module not found
insmod: ehci-hcd.ko: module not found
insmod: ohci-hcd.ko: module not found
insmod: xhci-hcd.ko: module not found
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
MTK MSDC device init.
msdc0 -> ops_get_cd return<0> <- msdc_ops_get_cd() : L<2317> PID<kworker/u:1><0x1a>
mtk-sd: MediaTek MT6575 MSDC Driver
usbcore: registered new interface driver usblp


Wireless reset gain value... 

ra0       mac:
[0x2320]:18360af8  
ra0       mac:
[0x2324]:18360af8  


Wireless reset gain value... 

ra0       mac:
[0x2320]:18360af8  
ra0       mac:
[0x2324]:18360af8  


Wireless reset gain value... 

ra0       mac:
[0x2320]:18360af8  
ra0       mac:
[0x2324]:18360af8  


Wireless reset gain value... 

ra0       mac:
[0x2320]:18360af8  
ra0       mac:
[0x2324]:18360af8  

dts

/dts-v1/;

#include "mt7621.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
	compatible = "strong,wr1200", "mediatek,mt7621-soc";
	model = "Strong 1200";

	aliases {
		led-boot = &led_power;
		led-failsafe = &led_power;
		led-running = &led_power;
		led-upgrade = &led_power;
	};

	memory@0 {
		device_type = "memory";
		reg = <0x0 0x8000000>;
	};

	chosen {
		bootargs = "console=ttyS0,57600";
	};

	gpio-leds {
		compatible = "gpio-leds";

		led_power: power {
			label = "wr1200:green:power";
			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
		};

		usb {
			label = "wr1200:green:usb";
			gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
			trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>;
			linux,default-trigger = "usbport";
		};

		data {
			label = "wr1200:green:data";
			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
		};
	};

	gpio-keys-polled {
		compatible = "gpio-keys-polled";
		poll-interval = <20>;

		reset {
			label = "reset";
			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_RESTART>;
		};
	};

};

&spi0 {
	status = "okay";

	m25p80@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <10000000>;
		m25p,chunked-io = <32>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "Bootloader";
				reg = <0x0 0x30000>;
				read-only;
			};

			partition@30000 {
				label = "Config";
				reg = <0x30000 0x10000>;
				read-only;
			};

			factory: partition@40000 {
				label = "Factory";
				reg = <0x40000 0x10000>;
				read-only;
			};

			partition@50000 {
				label = "firmware";
				reg = <0x50000 0xfa0000>;
			};

			partition@FF0000 {
				label = "Second_Config";
				reg = <0xFF0000 0x10000>;
				read-only;
			};

		};
	};
};

&ethernet {
	mtd-mac-address = <&factory 0x00000004>;
	mediatek,portmap = "llllw";
};

&sdhci {
	status = "okay";
};

&pcie {
	status = "okay";
};

&pcie0 {
	mt76@0,0 {
		reg = <0x0000 0 0 0 0>;
		mediatek,mtd-eeprom = <&factory 0x8000>;
		ieee80211-freq-limit = <5000000 6000000>;
	};
};

&pcie1 {
	mt76@0,0 {
		reg = <0x0000 0 0 0 0>;
		mediatek,mtd-eeprom = <&factory 0x0000>;
		ieee80211-freq-limit = <2400000 2500000>;
	};
};

&pinctrl {
	state_default: pinctrl0 {
		gpio {
			ralink,group = "i2c", "uart2", "uart3", "rgmii2";
			ralink,function = "gpio";
		};
	};
};

Openwrt without NAND

## Booting image at bc050000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.74
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3219611 Bytes =  3.1 MB
   Load Address: 80001000
   Entry Point:  80001000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 128

Starting kernel ...

[    0.000000] Linux version 4.14.74 (vk496@vk496-pc) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r8222-6ef1c978ba)) #0 SMP Mon Oct 8 08:03:23 2018
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Strong 1200
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2} total 2
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu @8110e000 s26192 r8192 d22960 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00011586
[    0.000000] Readback ErrCtl register=00011586
[    0.000000] Memory: 122388K/131072K available (4362K kernel code, 221K rwdata, 972K rodata, 1536K init, 241K bss, 8684K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 256
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000011] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015503] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.087800] pid_max: default: 32768 minimum: 301
[    0.097104] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110119] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.125818] Hierarchical SRCU implementation.
[    0.135121] smp: Bringing up secondary CPUs ...
[    0.145171] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.145180] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.145192] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.145340] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.204569] Synchronize counters for CPU 1: done.
[    0.264246] smp: Brought up 1 node, 2 CPUs
[    0.275635] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.295109] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.307363] pinctrl core: initialized pinctrl subsystem
[    0.319237] NET: Registered protocol family 16
[    0.332778] rt2880-pinmux pinctrl: error claiming hogs: -22
[    0.343765] rt2880-pinmux pinctrl: could not claim hogs: -22
[    0.355039] rt2880-pinmux: probe of pinctrl failed with error -22
[    0.386622] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.397952] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.409230] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    0.424702] clocksource: Switched to clocksource GIC
[    0.436448] NET: Registered protocol family 2
[    0.445774] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.459516] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.472130] TCP: Hash tables configured (established 1024 bind 1024)
[    0.484850] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.496366] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.509020] NET: Registered protocol family 1
[    1.914613] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    1.926004] Crashlog allocated RAM at address 0x3f00000
[    1.936500] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    1.958426] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.969938] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.993350] io scheduler noop registered
[    2.001170] io scheduler deadline registered (default)
[    2.012204] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    2.026434] console [ttyS0] disabled
[    2.033450] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 14, base_baud = 3125000) is a 16550A
[    2.051518] console [ttyS0] enabled
[    2.051518] console [ttyS0] enabled
[    2.065231] bootconsole [early0] disabled
[    2.065231] bootconsole [early0] disabled
[    2.082455] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.096168] libphy: Fixed MDIO Bus: probed
[    2.176446] mtk_soc_eth 1e100000.ethernet: generated random MAC address 9a:db:4b:7f:ef:5b
[    2.192922] libphy: mdio: probed
[    3.611031] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[    3.623653] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 16
[    3.643172] NET: Registered protocol family 10
[    3.653477] Segment Routing with IPv6
[    3.660900] NET: Registered protocol family 17
[    3.669800] 8021q: 802.1Q VLAN Support v1.8
[    3.680971] hctosys: unable to open rtc device (rtc0)
[    3.698903] Freeing unused kernel memory: 1536K
[    3.707960] This architecture does not have kernel memory protection.
[    3.730544] init: Console is alive
[    3.737688] init: - watchdog -
[    3.755639] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.774050] mtk_soc_eth 1e100000.ethernet eth0: port 0 link up
[    3.790832] usbcore: registered new interface driver usbfs
[    3.801943] usbcore: registered new interface driver hub
[    3.812692] usbcore: registered new device driver usb
[    3.833083] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[    3.850495] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[    3.868210] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    3.878837] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    3.904938] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x00210010
[    3.921859] xhci-mtk 1e1c0000.xhci: irq 15, io mem 0x1e1c0000
[    3.934327] random: fast init done
[    3.934393] hub 1-0:1.0: USB hub found
[    3.934484] hub 1-0:1.0: 2 ports detected
[    3.935292] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    3.935328] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    3.935355] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0  SuperSpeed
[    3.935539] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.936482] hub 2-0:1.0: USB hub found
[    3.936559] hub 2-0:1.0: 1 port detected
[    3.938939] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.055060] init: - preinit -
[    4.215120] mtk_soc_eth 1e100000.ethernet: PPE started
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.349856] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[    7.371702] procd: - early -
[    7.377683] procd: - watchdog -
[    8.004808] procd: - watchdog -
[    8.011377] procd: - ubus -
[    8.022159] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.075243] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.088278] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.101787] procd: - init -
Please press Enter to activate this console.
[    8.239496] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.255833] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.276106] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.293119] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    8.340837] xt_time: kernel timezone is -0000
[    8.355976] PPP generic driver version 2.4.2
[    8.366526] NET: Registered protocol family 24
[    8.378095] kmodloader: done loading kernel modules from /etc/modules.d/*
[    9.471008] urandom_read: 5 callbacks suppressed
[    9.471022] random: jshn: uninitialized urandom read (4 bytes read)
[    9.544038] random: jshn: uninitialized urandom read (4 bytes read)
[   12.489233] mtk_soc_eth 1e100000.ethernet: PPE started
[   12.539003] br-lan: port 1(eth0.1) entered blocking state
[   12.549811] br-lan: port 1(eth0.1) entered disabled state
[   12.561172] device eth0.1 entered promiscuous mode
[   12.570748] device eth0 entered promiscuous mode
[   12.593473] br-lan: port 1(eth0.1) entered blocking state
[   12.604276] br-lan: port 1(eth0.1) entered forwarding state
[   12.615768] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   13.515126] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.29.3 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r8278-b134b3299c
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------

openwrt_bootlog.txt

Starting kernel ...

[    0.000000] Linux version 4.14.74 (vk496@vk496-pc) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r8222-6ef1c978ba)) #0 SMP Thu Oct 4 22:44:55 2018
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Strong 1200
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2} total 2
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu @81110000 s26192 r8192 d22960 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00011586
[    0.000000] Readback ErrCtl register=00011586
[    0.000000] Memory: 123560K/131072K available (4428K kernel code, 231K rwdata, 988K rodata, 228K init, 276K bss, 7512K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 256
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000011] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015513] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.087814] pid_max: default: 32768 minimum: 301
[    0.097121] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110136] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.125898] Hierarchical SRCU implementation.
[    0.135212] smp: Bringing up secondary CPUs ...
[    0.145278] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.145287] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.145300] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.145458] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.204655] Synchronize counters for CPU 1: done.
[    0.264336] smp: Brought up 1 node, 2 CPUs
[    0.276125] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.295610] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.307863] pinctrl core: initialized pinctrl subsystem
[    0.319735] NET: Registered protocol family 16
[    0.341115] pull PCIe RST: RALINK_RSTCTRL = 0
[    0.650056] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.660121] ***** Xtal 40MHz *****
[    0.666850] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.677059] Port 0 N_FTS = 1b102800
[    0.683957] Port 1 N_FTS = 1b102800
[    0.690884] Port 2 N_FTS = 1b102800
[    1.849138] PCIE2 no card, disable it(RST&CLK)
[    1.857826]  -> 21007f2
[    1.862648] PCIE0 enabled
[    1.867844] PCIE1 enabled
[    1.873031] PCI host bridge /pcie@1e140000 ranges:
[    1.882555]  MEM 0x0000000060000000..0x000000006fffffff
[    1.892910]   IO 0x000000001e160000..0x000000001e16ffff
[    1.903274] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[    1.930889] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.942306] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.953555] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.966315] PCI host bridge to bus 0000:00
[    1.974359] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.988033] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    1.999747] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.013229] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.029936] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.045762] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    2.063204] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.076269] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.090056] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    2.103182] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.117016] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.130491] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.144830] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    2.158315] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[    2.172650] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[    2.186134] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[    2.199627] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.214135] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[    2.228470] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.238301] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.251805] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.266151] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[    2.280664] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
[    2.294993] pci 0000:00:01.0: PCI bridge to [bus 02]
[    2.304829] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    2.318321] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    2.334366] clocksource: Switched to clocksource GIC
[    2.345905] NET: Registered protocol family 2
[    2.355550] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.369317] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    2.381912] TCP: Hash tables configured (established 1024 bind 1024)
[    2.394654] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    2.406176] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    2.418834] NET: Registered protocol family 1
[    2.664319] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    2.675601] Crashlog allocated RAM at address 0x3f00000
[    2.686228] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    2.707917] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.719479] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.743186] io scheduler noop registered
[    2.750912] io scheduler deadline registered (default)
[    2.761567] gpio-export gpio_export: 1 gpio(s) exported
[    2.772839] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    2.787093] console [ttyS0] disabled
[    2.794118] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 14, base_baud = 3125000) is a 16550A
[    2.812117] console [ttyS0] enabled
[    2.812117] console [ttyS0] enabled
[    2.825876] bootconsole [early0] disabled
[    2.825876] bootconsole [early0] disabled
[    2.842559] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.855661] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[    2.869705] Enable NFI Clock
[    2.884913] # MTK NAND # : Use HW ECC
[   62.854331] INFO: rcu_sched self-detected stall on CPU
[   62.864562] 	0-...: (5999 ticks this GP) idle=6fe/140000000000001/0 softirq=26/26 fqs=2999 
[   62.881161] 	 (t=6000 jiffies g=-289 c=-290 q=146)
[   62.890689] NMI backtrace for cpu 0
[   62.897621] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.74 #0
[   62.909558] Stack : 00000000 80560000 00000000 8006f6cc 80580000 80528520 00000000 00000000
[   62.926185]         804f49c8 87c09d44 87c3037c 805608a7 804efaf8 00000001 87c09ce8 532616ab
[   62.942811]         00000000 00000000 805c0000 00003268 00000000 0000009e 00000007 00000000
[   62.959436]         00000000 80560000 000db255 00000000 00000000 00000000 80580000 00000000
[   62.976061]         805662a0 8055e0ac 000000e0 80560000 00000003 80287210 00000000 805c0000
[   62.992687]         ...
[   62.997544] Call Trace:
[   63.002432] [<80010680>] show_stack+0x58/0x100
[   63.011278] [<80435a9c>] dump_stack+0x9c/0xe0
[   63.019955] [<8043c944>] nmi_cpu_backtrace+0xe4/0x108
[   63.029996] [<8043ca30>] nmi_trigger_cpumask_backtrace+0xc8/0x168
[   63.042121] [<80083fb8>] rcu_dump_cpu_stacks+0xc4/0x13c
[   63.052507] [<80083414>] rcu_check_callbacks+0x310/0x814
[   63.063077] [<80086998>] update_process_times+0x34/0x7c
[   63.073486] [<8009757c>] tick_handle_periodic+0x34/0xd0
[   63.083893] [<80307040>] gic_compare_interrupt+0x70/0x80
[   63.094459] [<80076e30>] handle_percpu_devid_irq+0xbc/0x1a8
[   63.105559] [<800711a0>] generic_handle_irq+0x40/0x58
[   63.115628] [<8023be5c>] gic_handle_local_int+0x9c/0xe8
[   63.126013] [<8023c01c>] gic_irq_dispatch+0x10/0x20
[   63.135709] [<800711a0>] generic_handle_irq+0x40/0x58
[   63.145765] [<80452d3c>] do_IRQ+0x1c/0x2c
[   63.153730] [<8023afec>] plat_irq_dispatch+0xfc/0x138
[   63.163770] [<8000b5e8>] except_vec_vi_end+0xb8/0xc4
[   63.173650] [<802c8910>] mtk_nand_command_bp+0x34c/0x454
[   63.184211] [<802c9bec>] mtk_nand_probe+0x2b4/0xa64
[   63.193936] [<80297548>] platform_drv_probe+0x40/0x84
[   63.203977] [<80295a48>] really_probe+0x140/0x2b8
[   63.213326] [<80295c64>] __driver_attach+0xa4/0xdc
[   63.222848] [<80293afc>] bus_for_each_dev+0x5c/0xbc
[   63.232543] [<80294fb8>] bus_add_driver+0xf8/0x218
[   63.242065] [<80296530>] driver_register+0xac/0xfc
[   63.251586] [<80005650>] do_one_initcall+0xd0/0x1a0
[   63.261287] [<80587d78>] kernel_init_freeable+0x168/0x228
[   63.272035] [<8044cdbc>] kernel_init+0x10/0x10c
[   63.281039] [<8000b0d8>] ret_from_kernel_thread+0x14/0x1c

openwrt_bootlog2.txt

Starting kernel ...

[    0.000000] Linux version 4.14.74 (vk496@vk496-pc) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r8222-6ef1c978ba)) #0 SMP Mon Oct 8 08:03:23 2018
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Strong 1200
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2} total 2
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu @81110000 s26192 r8192 d22960 u57344
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00011580
[    0.000000] Readback ErrCtl register=00011580
[    0.000000] Memory: 123660K/131072K available (4367K kernel code, 216K rwdata, 972K rodata, 256K init, 241K bss, 7412K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 256
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000011] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015505] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.087798] pid_max: default: 32768 minimum: 301
[    0.097106] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110119] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.125833] Hierarchical SRCU implementation.
[    0.135135] smp: Bringing up secondary CPUs ...
[    0.145197] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.145206] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.145218] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.145369] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.204574] Synchronize counters for CPU 1: done.
[    0.264250] smp: Brought up 1 node, 2 CPUs
[    0.276051] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.295528] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.307772] pinctrl core: initialized pinctrl subsystem
[    0.319629] NET: Registered protocol family 16
[    0.341357] pull PCIe RST: RALINK_RSTCTRL = 0
[    0.650271] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.660334] ***** Xtal 40MHz *****
[    0.667065] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.677274] Port 0 N_FTS = 1b105000
[    0.684171] Port 1 N_FTS = 1b105000
[    0.691098] Port 2 N_FTS = 1b102800
[    1.849295] PCIE2 no card, disable it(RST&CLK)
[    1.857982]  -> 21007f2
[    1.862805] PCIE0 enabled
[    1.867999] PCIE1 enabled
[    1.873185] PCI host bridge /pcie@1e140000 ranges:
[    1.882710]  MEM 0x0000000060000000..0x000000006fffffff
[    1.893066]   IO 0x000000001e160000..0x000000001e16ffff
[    1.903429] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[    1.930710] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.942087] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.953407] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.966149] PCI host bridge to bus 0000:00
[    1.974192] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.987872] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    1.999580] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.013053] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.031330] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.044398] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.058186] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    2.071307] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.085133] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.098618] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.112957] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    2.126436] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref]
[    2.140779] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
[    2.154258] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
[    2.167749] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.182260] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[    2.196588] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.206428] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.219917] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.234268] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit]
[    2.248785] pci 0000:02:00.0: BAR 6: assigned [mem 0x60300000-0x6030ffff pref]
[    2.263118] pci 0000:00:01.0: PCI bridge to [bus 02]
[    2.272949] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    2.286445] pci 0000:00:01.0:   bridge window [mem 0x60300000-0x603fffff pref]
[    2.302809] clocksource: Switched to clocksource GIC
[    2.314281] NET: Registered protocol family 2
[    2.323920] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.337676] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    2.350280] TCP: Hash tables configured (established 1024 bind 1024)
[    2.363004] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    2.374523] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    2.387179] NET: Registered protocol family 1
[    2.632751] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    2.644043] Crashlog allocated RAM at address 0x3f00000
[    2.654527] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    2.676679] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.688192] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.711561] io scheduler noop registered
[    2.719381] io scheduler deadline registered (default)
[    2.730594] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    2.744775] console [ttyS0] disabled
[    2.751788] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 14, base_baud = 3125000) is a 16550A
[    2.769851] console [ttyS0] enabled
[    2.769851] console [ttyS0] enabled
[    2.783562] bootconsole [early0] disabled
[    2.783562] bootconsole [early0] disabled
[    2.800809] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.814339] spi-mt7621 1e000b00.spi: sys_freq: 50000000
[    2.825912] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    2.836058] 5 fixed-partitions partitions found on MTD device spi0.0
[    2.848702] Creating 5 MTD partitions on "spi0.0":
[    2.858249] 0x000000000000-0x000000030000 : "Bootloader"
[    2.870083] 0x000000030000-0x000000040000 : "Config"
[    2.881157] 0x000000040000-0x000000050000 : "Factory"
[    2.892408] 0x000000050000-0x000000ff0000 : "firmware"
[    2.905907] random: fast init done
[    2.940002] 2 uimage-fw partitions found on MTD device firmware
[    2.951806] 0x000000050000-0x0000002146fc : "kernel"
[    2.963022] 0x0000002146fc-0x000000ff0000 : "rootfs"
[    2.974055] mtd: device 5 (rootfs) set to be root filesystem
[    2.985475] 1 squashfs-split partitions found on MTD device rootfs
[    2.997805] 0x0000004d0000-0x000000ff0000 : "rootfs_data"
[    3.009731] 0x000000ff0000-0x000001000000 : "Second_Config"
[    3.022838] libphy: Fixed MDIO Bus: probed
[    3.094853] libphy: mdio: probed
[    4.501780] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[    4.514390] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 17
[    4.534042] NET: Registered protocol family 10
[    4.544409] Segment Routing with IPv6
[    4.551773] NET: Registered protocol family 17
[    4.560680] 8021q: 802.1Q VLAN Support v1.8
[    4.572023] hctosys: unable to open rtc device (rtc0)
[    4.588739] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    4.603677] Freeing unused kernel memory: 256K
[    4.612526] This architecture does not have kernel memory protection.
[    5.065323] random: crng init done
[    5.266873] init: Console is alive
[    5.274002] init: - watchdog -
[    6.287903] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.422051] usbcore: registered new interface driver usbfs
[    6.433171] usbcore: registered new interface driver hub
[    6.443923] usbcore: registered new device driver usb
[    6.463167] SCSI subsystem initialized
[    6.482084] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[    6.499440] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[    6.517135] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    6.527755] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    6.553055] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x00210010
[    6.570006] xhci-mtk 1e1c0000.xhci: irq 16, io mem 0x1e1c0000
[    6.582646] hub 1-0:1.0: USB hub found
[    6.590261] hub 1-0:1.0: 2 ports detected
[    6.598915] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    6.609603] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    6.624563] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0  SuperSpeed
[    6.637601] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    6.654722] hub 2-0:1.0: USB hub found
[    6.662250] hub 2-0:1.0: 1 port detected
[    6.676263] usbcore: registered new interface driver usb-storage
[    6.688618] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.723235] init: - preinit -
[    7.212334] mtk_soc_eth 1e100000.ethernet eth0: port 2 link up
[    7.571267] mtk_soc_eth 1e100000.ethernet: PPE started
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   10.800233] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   10.831335] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.920922] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[   10.943437] procd: - early -
[   10.949274] procd: - watchdog -
[   11.632993] procd: - watchdog -
[   11.639566] procd: - ubus -
[   11.725203] procd: - init -
Please press Enter to activate this console.
[   11.987057] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.012603] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.034042] Loading modules backported from Linux version v4.19-rc5-0-g6bf4ca7fbc85
[   12.049365] Backport generated by backports.git v4.19-rc5-1-0-g05571dcd
[   12.064876] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.082436] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   12.136540] xt_time: kernel timezone is -0000
[   12.199806] bus=0x1, slot = 0x0, irq=0xff
[   12.208175] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[   12.873525] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[   12.889548] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[   12.900532] mt76x2e 0000:01:00.0: Build: 1
[   12.908722] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[   12.942814] mt76x2e 0000:01:00.0: Firmware running!
[   12.959116] bus=0x2, slot = 0x1, irq=0xff
[   12.967477] mt76x2e 0000:02:00.0: ASIC revision: 76020044
[   13.632850] mt76x2e 0000:02:00.0: ROM patch already applied
[   13.644943] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
[   13.655946] mt76x2e 0000:02:00.0: Build: 1
[   13.664131] mt76x2e 0000:02:00.0: Build Time: 201507311614____
[   13.692816] mt76x2e 0000:02:00.0: Firmware running!
[   13.716092] PPP generic driver version 2.4.2
[   13.727277] NET: Registered protocol family 24
[   13.740525] kmodloader: done loading kernel modules from /etc/modules.d/*
[   18.930411] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   18.962905] jffs2_build_filesystem(): unlocking the mtd device... 
[   18.962922] done.
[   18.979064] jffs2_build_filesystem(): erasing all blocks after the end marker... 
[   20.836846] mtk_soc_eth 1e100000.ethernet: PPE started
[   20.941506] br-lan: port 1(eth0.1) entered blocking state
[   20.952417] br-lan: port 1(eth0.1) entered disabled state
[   20.963807] device eth0.1 entered promiscuous mode
[   20.973427] device eth0 entered promiscuous mode
[   21.024983] br-lan: port 1(eth0.1) entered blocking state
[   21.035771] br-lan: port 1(eth0.1) entered forwarding state
[   21.047163] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   21.873345] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready