|
# current version: artillery_tft_fw_1.27.x_patch_9.2 |
|
#-------------------------------------------------------------------- |
|
# |
|
# DEFAULT CONFIG FILE FOR BigTreeTech TFT CONTROLLERS |
|
# |
|
#-------------------------------------------------------------------- |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Supported TFT Variants |
|
#-------------------------------------------------------------------- |
|
# |
|
# BIGTREE_TFT24_V1_1 / BIGTREE_TFT28_V1_0 / BIGTREE_TFT28_V3_0 |
|
# BIGTREE_TFT35_V1_0 / BIGTREE_TFT35_V1_1 / BIGTREE_TFT35_V1_2 |
|
# BIGTREE_TFT35_V2_0 / BIGTREE_TFT35_V3_0 / BIGTREE_TFT35_E3_V3_0 |
|
# BIGTREE_TFT35_B1_V3_0 / BIGTREE_TFT43_V3_0 / BIGTREE_TFT50_V3_0 |
|
# BIGTREE_TFT70_V3_0 |
|
# |
|
# BIGTREE_GD_TFT24_V1_1 / BIGTREE_GD_TFT35_V2_0 / BIGTREE_GD_TFT35_V3_0 |
|
# BIGTREE_GD_TFT35_E3_V3_0 / BIGTREE_GD_TFT35_B1_V3_0 / BIGTREE_GD_TFT43_V3_0 |
|
# BIGTREE_GD_TFT50_V3_0 / BIGTREE_GD_TFT70_V3_0 |
|
# |
|
# MKS_TFT28_V3_0 / MKS_TFT28_V4_0 / MKS_TFT28_NEW_GENIUS |
|
# MKS_TFT32_V1_3 / MKS_TFT32_V1_4 / MKS_TFT35_V1_0 |
|
# |
|
# Firmware source: https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Supported Marlin Firmware Versions |
|
#-------------------------------------------------------------------- |
|
# |
|
# Minimum Marlin firmware version: 2.1.1 |
|
# Distribution date: 2022-08-06 |
|
# Firmware source: https://github.com/MarlinFirmware/Marlin/releases |
|
# |
|
# To use all the features and functionalities supported by the TFT, |
|
# the following options must be enabled in Marlin firmware. |
|
# |
|
# General options which MUST be always activated: |
|
# EEPROM_SETTINGS (in Configuration.h) |
|
# BABYSTEPPING (in Configuration_adv.h) |
|
# AUTO_REPORT_TEMPERATURES (in Configuration_adv.h) |
|
# AUTO_REPORT_POSITION (in Configuration_adv.h) |
|
# M115_GEOMETRY_REPORT (in Configuration_adv.h) |
|
# M114_DETAIL (in Configuration_adv.h) |
|
# REPORT_FAN_CHANGE (in Configuration_adv.h) |
|
# |
|
# Options to support printing from onboard media: |
|
# SDSUPPORT (in Configuration.h) |
|
# LONG_FILENAME_HOST_SUPPORT (in Configuration_adv.h) |
|
# AUTO_REPORT_SD_STATUS (in Configuration_adv.h) |
|
# SDCARD_CONNECTION ONBOARD (in Configuration_adv.h) |
|
# |
|
# Options to support dialog with host: |
|
# EMERGENCY_PARSER (in Configuration_adv.h) |
|
# SERIAL_FLOAT_PRECISION 4 (in Configuration_adv.h) |
|
# HOST_ACTION_COMMANDS (in Configuration_adv.h) |
|
# HOST_PROMPT_SUPPORT (in Configuration_adv.h) |
|
# HOST_STATUS_NOTIFICATIONS (in Configuration_adv.h) |
|
# |
|
# Options to support M600 with host & (Un)Load menu: |
|
# Options to support dialog with host (as pre requisite) |
|
# NOZZLE_PARK_FEATURE (in Configuration.h) |
|
# ADVANCED_PAUSE_FEATURE (in Configuration_adv.h) |
|
# PARK_HEAD_ON_PAUSE (in Configuration_adv.h) |
|
# FILAMENT_LOAD_UNLOAD_GCODES (in Configuration_adv.h) |
|
# |
|
# Options to fully support Bed Leveling menu: |
|
# Z_MIN_PROBE_REPEATABILITY_TEST (in Configuration.h) |
|
# G26_MESH_VALIDATION (in Configuration.h) |
|
# Z_STEPPER_AUTO_ALIGN (in Configuration_adv.h) |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# General Settings |
|
#-------------------------------------------------------------------- |
|
|
|
#### Serial Ports (Primary and Supplementary) |
|
# Serial ports connected to devices such as Printer, ESP3D, OctoPrint and other Controllers. |
|
# In order to successfully establish a communication through a serial port, set a baudrate |
|
# matching the baudrate configured on the connected device. |
|
# Disable the serial port when it is not in use and/or not connected to a device (floating) to |
|
# avoid to receive and process wrong data due to possible electromagnetic interference (EMI). |
|
# |
|
# NOTES: |
|
# - Serial port P1 is the primary serial connection to the printer and cannot be disabled. |
|
# - A baudrate of 250000 works in most cases, but you can try a lower speed if you |
|
# commonly experience drop-outs during host printing. |
|
# You may try up to 1000000 to speed up SD file transfer. |
|
# |
|
# Format: [serial_port: P1:<baudrate> P2:<baudrate> P3:<baudrate> P4:<baudrate> |
|
# Target port: P1: Printer |
|
# P2: WIFI (e.g. ESP3D) |
|
# P3: UART 3 (e.g. OctoPrint) |
|
# P4: UART 4 |
|
# Value range: P1: [min: 1, max: 9] |
|
# P2: [min: 0, max: 9] |
|
# P3: [min: 0, max: 9] |
|
# P4: [min: 0, max: 9] |
|
# Options: [OFF (port disabled): 0, 2400: 1, 9600: 2, 19200: 3, 38400: 4, 57600: 5, 115200: 6, 250000: 7, 500000: 8, 1000000: 9] |
|
serial_port:P1:7 P2:0 P3:0 P4:0 |
|
|
|
#### Emulated M600 |
|
# The TFT intercepts the M600 G-code (filament change) and emulates the handling logic |
|
# otherwise provided by Marlin firmware. |
|
# |
|
# NOTE: Enable it in case Marlin firmware does not properly support M600 on the mainboard. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
emulated_m600:0 |
|
|
|
#### Emulated M109 And M190 |
|
# The TFT intercepts the blocking M109 and M190 G-codes (set target hotend and bed temperatures) |
|
# and converts them to the non-blocking M104 and M140 G-codes respectively. |
|
# |
|
# NOTE: Enable it so the TFT can still communicate with Marlin firmware even if the target |
|
# temperature is not reached yet. Otherwise the communication (TFT<->Marlin) will be |
|
# frozen until desired/set temperatures are obtained. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
emulated_m109_m190:1 |
|
|
|
#### Event LED |
|
# When printing from TFT SD card / TFT USB disk, the TFT periodically sets the printer's (neopixel) |
|
# LED color and TFT's knob LED color, if any, according to the current nozzle and bed temperatures. |
|
# |
|
# NOTE: If "emulated_m109_m190" is disabled (heating controlled by printer), the TFT cannot control the |
|
# printer's (neopixel) LED during heating. It will control only the TFT's knob LED, if any. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
event_led:1 |
|
|
|
#### G-code File Comment Parsing |
|
# The TFT parses and processes extra information provided by the slicer as comments in the G-code file. |
|
# If enabled, the current implementation parses and processes print time and print layer information |
|
# from the G-code file (nothing else). |
|
# If disabled, the "layer_disp_type" setting provided in "UI Settings" section becomes redundant. |
|
# |
|
# NOTE: Enable it in case the slicer (e.g. Cura) supports extra information. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
file_comment_parsing:1 |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# UI Settings |
|
#-------------------------------------------------------------------- |
|
|
|
#### Rotated UI |
|
# Rotate UI by 180 degrees. |
|
# Options: [disable: 0, enable: 1] |
|
rotated_ui:0 |
|
|
|
#### Touch Mode Language |
|
# Select the language to use on the LCD while in Touch Mode. |
|
# |
|
# NOTE: To add/flash a second language copy the required "language_xx.ini" file from |
|
# "Language Packs" folder to the SD root folder. |
|
# Then press the reset button to load/flash the copied language file. |
|
# |
|
# Options: [Primary Language (english): 0, Secondary Language: 1] |
|
language:0 |
|
|
|
#### Status Screen |
|
# Select the default home screen while in Touch Mode. |
|
# If enabled, the Status Screen menu will become the default home screen. |
|
# If disabled, the Main menu will become the default home screen. |
|
# |
|
# NOTE: Both the Status Screen and Main menus display the current temperature, fan and speeds. |
|
# Furthermore, the Status Screen menu provides the status area reporting the printer notifications. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
status_screen:1 |
|
|
|
#### Touch Mode Colors |
|
# Set colors used in Touch Mode. |
|
# |
|
# NOTE: Select an option from the provided list or set the color (RGB888 format) hex value directly |
|
# (start with "0x"), such as: Red: 0xFF0000, Green: 0x00FF00, Blue: 0x0000FF. |
|
# |
|
# Options: [ WHITE: 0, BLACK: 1, RED: 2, GREEN: 3, BLUE: 4, CYAN: 5, MAGENTA: 6, YELLOW: 7, |
|
# ORANGE: 8, PURPLE: 9, LIME: 10, BROWN: 11, DARKBLUE: 12, DARKGREEN: 13, GRAY: 14, DARKGRAY: 15] |
|
|
|
## Title background color |
|
title_background_color:1 |
|
|
|
## Menu background color |
|
menu_background_color:1 |
|
|
|
## Menu font color |
|
menu_font_color:0 |
|
|
|
## Reminder font color, such as: "No print attached", "Busy processing", etc. |
|
reminder_font_color:2 |
|
|
|
## Status (e.g. volume reminder, ABL probing point etc.) font color, such as: "Card inserted", "Card removed" |
|
status_font_color:5 |
|
|
|
## Background color for X Y Z position display in Status Screen menu |
|
status_xyz_bg_color:15 |
|
|
|
## List View border color |
|
list_border_color:15 |
|
|
|
## List View button background color |
|
list_button_bg_color:15 |
|
|
|
## Color used by the Mesh Editor menu for drawing the mesh with the minimum value in the grid |
|
mesh_min_color:7 |
|
|
|
## Color used by the Mesh Editor menu for drawing the mesh with the maximum value in the grid |
|
mesh_max_color:2 |
|
|
|
#### Terminal Text Color Scheme |
|
# Color scheme for displaying text in Terminal menu. |
|
# Options: [Material Dark: 0, Material Light: 1, High Contrast: 2] |
|
# Material Dark: Dark background with light font color and orange command font color. |
|
# Material Light: Light background with dark font color and orange command font color. |
|
# High Contrast: Black background with white font color and orange command font color. |
|
terminal_color_scheme:2 |
|
|
|
#### Notification Style For ACK Messages |
|
# Set the notification style to use for displaying the ACK messages which start with "echo:". |
|
# |
|
# NOTE: The OFF value is applied to any ACK message type (e.g. even to known echo ACK). |
|
# It means that any kind of ACK message is silently discarded. |
|
# |
|
# Options: [OFF: 0, POPUP: 1, TOAST: 2] |
|
# OFF: No notification. The message is ignored. |
|
# POPUP: Display a popup window for user confirmation. |
|
# TOAST: A non-blocking Toast notification is displayed for few seconds. No user interaction is needed. |
|
ack_notification:1 |
|
|
|
#### Files Sorting |
|
# Sort files and folders based on the selected option. |
|
# |
|
# NOTE: Only applicable for files in TFT SD card and TFT USB disk. |
|
# |
|
# Options: [Date Newest First: 0, Date Oldest First: 1, Name Ascending: 2, Name Descending: 3] |
|
files_sort_by:0 |
|
|
|
#### Files List Mode |
|
# Display files in list mode instead of icon mode. |
|
# Options: [disable: 0, enable: 1] |
|
files_list_mode:1 |
|
|
|
#### Filename Extension |
|
# Display fullname for files listed in List Mode / Icon Mode menu. |
|
# If disabled, any filename extension starting with ".g" or ".G" (e.g. ".g", ".gco", ".gcode" etc.) will be hidden. |
|
# Options: [disable: 0, enable: 1] |
|
filename_extension:1 |
|
|
|
#### Fan Speed In Percentage |
|
# Show fan speed in percentage. If disabled fan speed will be displayed as PWM values. |
|
# Options: [disable: 0, enable: 1] |
|
fan_speed_percentage:1 |
|
|
|
#### Persistent Temperature Info |
|
# Show persistent temperature info in all menus. |
|
# Options: [disable: 0, enable: 1] |
|
persistent_info:1 |
|
|
|
#### Temperature And Wait ACK In Terminal |
|
# Show "temperature" and "wait" ACK in Terminal menu. |
|
# Options: [disable: 0, enable: 1] |
|
terminal_ack:0 |
|
|
|
#### Notification M117 |
|
# If enabled, any notification received from Marlin through "//action:notification" is also |
|
# stored on the notification screen. The notification screen reporting the history of the |
|
# received notifications is displayed pressing on the notification bar. |
|
# |
|
# NOTE: Marlin notifications are also always displayed on the Status Screen menu. |
|
# Furthermore, they are also displayed on the notification bar as toast messages |
|
# in case the current menu is not the Status Screen menu. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
notification_m117:0 |
|
|
|
#### Progress Source |
|
# This sets the source of the progress calculation, G-code file advance based or time based. |
|
# In file mode it is a simple file progress, it tells you the percentage of the G-codes |
|
# executed. It doesn't reflect the amount of work done, only in a very few cases (ex. a 2D |
|
# shape expanded vertically like a cylinder, cube, etc). |
|
# Time based mode is very close to the real amount of work done, but it is still not perfect, |
|
# it relies on the estimate the slicer has done. It needs info from the slicer, the elapsed |
|
# time or the remaining time, if it's missing, the progress source defaults to file progress |
|
# mode. If no "M73 R" is present in the G-code file than it requires "file_comment_parsing" |
|
# to be enabled. |
|
# |
|
# NOTE: If "M73 P" is present in the G-code file than file or time based progress will be |
|
# overriden by that. |
|
# |
|
# Options: [File progress mode: 0, Time based progress: 1] |
|
prog_source:0 |
|
|
|
#### Progress Numeric Display Mode During Print |
|
# This sets the default display type for print progress numeric display. It can be changed during |
|
# print by pressing the hourglass icon. |
|
# At each click it will alter between the 3 variants. |
|
# |
|
# NOTE: Some slicers include time related info in the G-code files as comments. If the time info |
|
# is not added by the slicer, then a post processing plugin is needed that adds that info in |
|
# the G-code file (comment or M73 Rxx format). |
|
# If no remaining time info is present in the G-code file (comment or M73 Rxx), the display |
|
# defaults to option 0. |
|
# |
|
# Options: [Percentage & Elapsed time: 0, Percentage & Remaining time: 1, Elapsed time & Remaining time: 2] |
|
prog_disp_type:2 |
|
|
|
#### Current Layer Display Mode During Print |
|
# This sets the default display type for the printing layer. It can be changed during print by |
|
# pressing the nozzle icon. At each click it will alter between the 3 variants. |
|
# |
|
# NOTES: |
|
# - It requires "file_comment_parsing" to be enabled. |
|
# - This feature uses the layer number comments added by slicers at the starting of each layer. |
|
# - Some slicers may not include the total number of layers in the G-code file. In this case only |
|
# the current layer will be displayed. To display total number of layers, a comment should be |
|
# added at the beginning of the G-code file in the format "; Layer count: xx". |
|
# Separators can be " ", ":", "_" or "=". |
|
# - If the total number of layers exceeds 999, this information will not be displayed because |
|
# there is not enough space for both current and total layer number to be shown. |
|
# |
|
# - For PrusaSlicer, to enable this feature, following comment lines must be added in |
|
# Printer Settings -> Custom G-code section: |
|
# - In After layer change G-code section: |
|
# ";LAYER:[layer_num]" |
|
# - In Start G-code section: |
|
# ";LAYER_COUNT:[total_layer_count]" |
|
# |
|
# Options: [Layer height: 0, Layer number: 1, Both - height & number: 2] |
|
layer_disp_type:0 |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Marlin Mode Settings (only for TFT24 V1.1 & TFT28/TFT35/TFT43/TFT50/TFT70 V3.0) |
|
#-------------------------------------------------------------------- |
|
|
|
#### Default Mode |
|
# Set Marlin/Touch Mode as the default mode at startup. |
|
# |
|
# NOTE: Mode switching is possible only for Marlin Mode and Touch Mode by a long press of |
|
# 1.5 seconds on the display or holding down the encoder button for 1.5 seconds. |
|
# |
|
# Options: [Marlin Mode: 0, Touch Mode: 1, Blocked Marlin Mode: 2, Blocked Touch Mode: 3] |
|
default_mode:1 |
|
|
|
#### Serial Always ON |
|
# Keep UART (serial communication) alive in Marlin Mode. |
|
# Allows seamless OctoPrint UART connection to the TFT's UART/serial expansion port |
|
# no matter which mode the TFT is in. |
|
# Options: [disable: 0, enable: 1] |
|
serial_always_on:0 |
|
|
|
#### Marlin Mode Background & Font Colors |
|
# Set colors used in Marlin Mode. |
|
# |
|
# NOTE: Select an option from the provided list or set the color (RGB888 format) hex value directly |
|
# (start with "0x"), such as: Red: 0xFF0000, Green: 0x00FF00, Blue: 0x0000FF. |
|
# |
|
# Options: [ WHITE: 0, BLACK: 1, RED: 2, GREEN: 3, BLUE: 4, CYAN: 5, MAGENTA: 6, YELLOW: 7, |
|
# ORANGE: 8, PURPLE: 9, LIME: 10, BROWN: 11, DARKBLUE: 12, DARKGREEN: 13, GRAY: 14, DARKGRAY: 15] |
|
|
|
## Marlin Mode background color |
|
marlin_background_color:1 |
|
|
|
## Marlin Mode font color |
|
marlin_font_color:8 |
|
|
|
#### Fullscreen Marlin Mode |
|
# Run Marlin Mode in fullscreen. |
|
# |
|
# NOTE: Disable is recommended for TFT24. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
marlin_fullscreen:1 |
|
|
|
#### Show Marlin Mode Title |
|
# Show banner text at the top of the TFT in Marlin Mode. |
|
# Options: [disable: 0, enable: 1] |
|
marlin_show_title:1 |
|
|
|
#### Marlin Mode Title |
|
# Banner text displayed at the top of the TFT in Marlin Mode. |
|
# Value range: [min: 3, max: 20 characters] |
|
marlin_title:Marlin Mode |
|
|
|
#### Marlin Mode Type |
|
# Select Marlin Mode type. |
|
# Options: [128x64 Full Graphic LCD: 0, 20x4 Character LCD: 1] |
|
marlin_type:0 |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Printer / Machine Settings |
|
#-------------------------------------------------------------------- |
|
|
|
#### Hotend Count |
|
# Value range: [min: 0, max: 6] |
|
hotend_count:1 |
|
|
|
#### Heated Bed Support |
|
# Options: [disable: 0, enable: 1] |
|
heated_bed:1 |
|
|
|
#### Heated Chamber Support |
|
# The TFT will auto-detect if chamber heating is enabled in Marlin firmware. |
|
# Options: [disable: 0, enable: 1] |
|
heated_chamber:0 |
|
|
|
#### Extruder Count |
|
# Value range: [min: 0, max: 6] |
|
ext_count:1 |
|
|
|
#### Fan Count |
|
# Value range: [min: 1, max: 6] |
|
fan_count:1 |
|
|
|
#### Controller Fan Support |
|
# Enable/disable controller fan speed control for Active and Idle cooling if Marlin |
|
# firmware supports controller fan (M710). |
|
# Options: [disable: 0, enable: 1] |
|
controller_fan:0 |
|
|
|
#### Bed / Extruder / Chamber Maximum Temperatures |
|
# Format: [max_temp: T0:<max temp> T1:<max temp> T2:<max temp> T3:<max temp> T4:<max temp> T5:<max temp> BED:<max temp> CHAMBER:<max temp>] |
|
# Unit: [temperature in °C] |
|
# Value range: hotend: [min: 20, max: 1000] |
|
# bed: [min: 20, max: 400] |
|
# chamber: [min: 20, max: 200] |
|
max_temp:T0:275 T1:275 T2:275 T3:275 T4:275 T5:275 BED:150 CHAMBER:60 |
|
|
|
#### Cold Extrusion Minimum Temperature |
|
# Minimum temperature needed to extrude/retract. |
|
# Any extrusion/retraction below this temperature will be prevented. |
|
# Unit: [temperature in °C] |
|
# Value range: [min: 20, max: 1000] |
|
min_temp:180 |
|
|
|
#### Fan Maximum PWM Speed |
|
# Set minimum and maximum fan speed allowed by the printer for Cooling Fans & Controller Fan. |
|
# Cooling fans have index from F0 to F5. |
|
# Controller fan has index CtA and CtI (Active and Idle). It requires "controller_fan" to be enabled. |
|
# Format: [fan_max: F0:<max PWM> F1:<max PWM> F2:<max PWM> F3:<max PWM> F4:<max PWM> F5:<max PWM> CtA:<max PWM> CtI:<max PWM>] |
|
# Unit: [PWM] |
|
# Value range: [min: 25, max: 255] |
|
fan_max:F0:255 F1:255 F2:255 F3:255 F4:255 F5:255 CtA:255 CtI:255 |
|
|
|
#### Machine Size / Build Area |
|
# The TFT will auto-detect the machine size (min and max) in Marlin firmware (requires |
|
# enabling "M115_GEOMETRY_REPORT" in Configuration_adv.h in Marlin firmware). |
|
# Format: [size_min: X<minimum distance> Y<minimum distance> Z<minimum distance>] |
|
# [size_max: X<maximum distance> Y<maximum distance> Z<maximum distance>] |
|
# Unit: [distance in mm] |
|
# Value range: [min: -2000, max: 2000] |
|
size_min:X0 Y0 Z0 |
|
size_max:X230 Y220 Z250 |
|
|
|
#### X & Y Move Speeds/Feedrates |
|
# Move speeds used in Move menu to move X and Y axes. |
|
# Format: [move_speed: S<feedrate> N<feedrate> F<feedrate>] |
|
# Unit: [feedrate in mm/min] |
|
# Value range: [min: 10, max: 12000] |
|
xy_speed:S1000 N3000 F5000 |
|
|
|
#### Z Speeds/Feedrates |
|
# Move speeds used in Move menu to move Z axis. |
|
# Format: [move_speed: S<feedrate> N<feedrate> F<feedrate>] |
|
# Unit: [feedrate in mm/min] |
|
# Value range: [min: 10, max: 12000] |
|
z_speed:S500 N1000 F2000 |
|
|
|
#### Extruder Speeds/Feedrates |
|
# Speed settings used to extrude/retract. |
|
# Format: [ext_speed: S<feedrate> N<feedrate> F<feedrate>] |
|
# Unit: [feedrate in mm/min] |
|
# Value range: [min: 10, max: 12000] |
|
ext_speed:S60 N600 F1200 |
|
|
|
#### Auto Save/Load Bed Leveling Data |
|
# The TFT will auto-detect if Auto Bed Level is available. |
|
# Enable this will send "M500" after "G29" to store leveling value and send "M420 S1" |
|
# to enable leveling state after startup. |
|
# Options: [disable: 0, enable: 1] |
|
auto_load_leveling:1 |
|
|
|
#### Onboard / Printer Media Support |
|
# On Marlin firmware, the TFT will auto-detect onboard media. |
|
# Auto-detect is not available for other firmwares like Smoothieware. |
|
# Options: [disable: 0, enable: 1, auto-detect: 2] |
|
onboard_sd:2 |
|
|
|
#### M27 Printing Status Refresh Time |
|
# M27 printing status refresh time (this will be used if SD_AUTOREPORT is not detected by the TFT). |
|
# Unit: [time in seconds] |
|
# Value range: [min: 1, max: 100] |
|
M27_refresh_time:3 |
|
|
|
#### M27 Always Active |
|
# Keep polling M27 even if not printing (e.g. SD print not started from TFT). |
|
# Options: [disable: 0, enable: 1] |
|
M27_always_active:1 |
|
|
|
#### Long File Names Support |
|
# On Marlin firmware, the TFT will auto-detect Long File Name support. |
|
# Auto-detect is not available for other firmwares like Smoothieware. |
|
# Options: [disable: 0, enable: 1, auto-detect: 2] |
|
long_filename:2 |
|
|
|
#### Pause/Nozzle Park Settings |
|
# These settings are used when a print is paused or in any feature which requires moving/parking the nozzle |
|
# before performing a task like in (Un)Load or Extruder Tuning menus. |
|
|
|
## Pause Retract Length |
|
# Format: [pause_retract: R<retract length> P<resume purge length>] |
|
# Unit: [length in mm] |
|
# Value range: [min: 0.0, max: 20.0] |
|
pause_retract:R15.0 P16.0 |
|
|
|
## Pause XY Position |
|
# NOTES: |
|
# - It MUST BE a value >= 0 for a Cartesian printer. |
|
# - It MUST BE a value <= 0 for a Delta printer. |
|
# |
|
# Format: [pause_pos: X<position> Y<position>] |
|
# Unit: [position in mm] |
|
# Value range: [min: -2000.0, max: 2000.0] |
|
pause_pos:X10.0 Y10.0 |
|
|
|
## Pause Z Raise |
|
# Raise Z axis by this value relative to the current layer height. |
|
# Unit: [distance in mm] |
|
# Value range: [min: 0.0, max: 2000.0] |
|
pause_z_raise:10.0 |
|
|
|
## Pause Feed Rate |
|
# Feedrate to use when moving an axis when printing is paused. |
|
# Format: [pause_feedrate: XY<feedrate> Z<feedrate> E<feedrate>] |
|
# Unit: [feedrate in mm/min] |
|
# Value range: [min: 10, max: 12000] |
|
pause_feedrate:XY6000 Z6000 E600 |
|
|
|
#### Leveling Settings |
|
# These settings are used for leveling. |
|
|
|
## Leveling Edge Distance (Manual Leveling, Leveling Corner) |
|
# Inset distance from bed edges. This distance is added to minimum X & Y bed coordinates and |
|
# subtracted from maximum X & Y bed coordinates to calculate manual leveling points. |
|
# For Leveling Corner, the default distance is the maximum between this setting value and |
|
# the rounded probe offset X/Y values configured in Marlin firmware. |
|
# Unit: [distance in mm] |
|
# Value range: [min: 0, max: 2000] |
|
level_edge_distance:20 |
|
|
|
## Leveling Z Position (Manual Leveling, Leveling Corner, Mesh Leveling, Probe/Home Offset, Mesh Tuner) |
|
# For Manual Leveling and MBL, lower Z axis to this absolute position after reaching a leveling point. |
|
# For Probe/Home Offset and ABL in Mesh Tuner, raise Z axis by this relative position after reaching |
|
# a leveling point. |
|
# Unit: [position in mm] |
|
# Value range: [min: 0.0, max: 2000.0] |
|
level_z_pos:0.1 |
|
|
|
## Leveling Z Raise (Manual Leveling, Leveling Corner, Mesh Leveling) |
|
# Raise Z axis by this relative value before moving to another point during leveling/probing procedures. |
|
# Unit: [distance in mm] |
|
# Value range: [min: 0.0, max: 2000.0] |
|
level_z_raise:10.0 |
|
|
|
## Leveling Feed Rate (Manual Leveling, Leveling Corner, Mesh Leveling) |
|
# Feedrate to use when moving an axis during leveling/probing procedures. |
|
# Format: [level_feedrate: XY<feedrate> Z<feedrate>] |
|
# Unit: [feedrate in mm/min] |
|
# Value range: [min: 10, max: 12000] |
|
level_feedrate:XY6000 Z6000 |
|
|
|
#### Inverted Axes (Manual Leveling, Leveling Corner, Move, Probe Offset) |
|
# Used by Manual Leveling, Leveling Corner, Move and Probe Offset menus in order axis matches the actual axis movement. |
|
# |
|
# NOTE: The Y axis of different printer (move hotbed or move nozzle) move in different directions. |
|
# So Y axis leveling inversion can't follow up inverted_axis[Y_AXIS]. |
|
# We separate a single variable "LY" (Leveling Y axis) to deal with the Y axis leveling movement direction. |
|
# |
|
# Format: [X<option> Y<option> Z<option> LY<option>] |
|
# Options: [disable: 0, enable: 1] |
|
inverted_axis:X0 Y0 Z0 LY0 |
|
|
|
#### Probing For Z Offset (Probe Offset) |
|
# Used by the Probe Offset menu for the Z offset tuning process. |
|
# If enabled, after homing a probing in the center of the bed is performed and then the nozzle |
|
# is moved to the XY probing point. |
|
# If disabled, after homing the nozzle is moved directly to the XY homing point. This is useful |
|
# in case Marlin firmware is configured to use the probe for Z axis homing (e.g. |
|
# USE_PROBE_FOR_Z_HOMING enabled in Marlin firmware) to avoid a second probing after homing. |
|
# |
|
# NOTES: |
|
# - Enable it in case Marlin firmware is not configured to use the probe for Z axis homing |
|
# (e.g. USE_PROBE_FOR_Z_HOMING disabled in Marlin firmware) or the XY probing point set |
|
# for homing is not reachable by the nozzle (e.g. due to HW limitations/constraints or |
|
# printer specific configuration). |
|
# - Disable it (preferably) in case Marlin firmware is configured to use the probe for Z axis |
|
# homing (e.g. USE_PROBE_FOR_Z_HOMING enabled in Marlin firmware). |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
probing_z_offset:1 |
|
|
|
#### Probing Z Raise (Probe Offset, Mesh Editor) |
|
# Used by the Probe Offset / Mesh Editor menu for the Z offset / Z height tuning process. |
|
# Raise / drop Z axis by this relative value after homing (G28) before starting to probe a point. |
|
# |
|
# NOTES: |
|
# - It MUST BE a value >= 0 (e.g. 20) for a Cartesian printer to avoid crashing into the bed. |
|
# - It MUST BE a value <= 0 (e.g. -50) for a Delta printer to avoid crashing into the top of the tower. |
|
# |
|
# Unit: [distance in mm] |
|
# Value range: [min: -2000.0, max: 2000.0] |
|
probing_z_raise:20.0 |
|
|
|
#### Z Steppers Auto-Alignment (ABL) |
|
# It allows to align multiple Z stepper motors using a bed probe by probing one position per stepper. |
|
# Enable this setting to show an icon in ABL menu allowing to run G34 command (it requires |
|
# Z_STEPPER_AUTO_ALIGN enabled in Configuration_adv.h in Marlin firmware). |
|
# |
|
# NOTE: Only for Marlin printers with one stepper driver per Z stepper motor and no Z timing belt. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
z_steppers_alignment:0 |
|
|
|
#### TouchMI Settings (ABL) |
|
# Enable this option for displaying TouchMI sensor settings in ABL menu (Init, Z Offset, Save, Test). |
|
# Options: [disable: 0, enable: 1] |
|
touchmi_sensor:0 |
|
|
|
#### Preheat Temperatures |
|
# Format: [preheat_name_X:<name>] |
|
# [preheat_temp_X:T<hotend temp> B<bed temp>] |
|
# Unit: [temperature in °C] |
|
# Value range: name: [min: 3, max: 20 characters] |
|
# hotend temp: [min: 20, max: 1000] |
|
# bed temp: [min: 20, max: 400] |
|
preheat_name_1:PLA |
|
preheat_temp_1:T200 B60 |
|
|
|
preheat_name_2:PETG |
|
preheat_temp_2:T240 B70 |
|
|
|
preheat_name_3:ABS |
|
preheat_temp_3:T230 B90 |
|
|
|
preheat_name_4:WOOD |
|
preheat_temp_4:T170 B50 |
|
|
|
preheat_name_5:TPU |
|
preheat_temp_5:T220 B50 |
|
|
|
preheat_name_6:NYLON |
|
preheat_temp_6:T250 B90 |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Power Supply Settings (only if connected to TFT controller) |
|
#-------------------------------------------------------------------- |
|
|
|
#### Active HIGH Power Supply Logic |
|
# Used in case it is supported by the TFT. |
|
# The power supply uses this HIGH signal logic to stay ON. |
|
# The power supply uses the opposite of this logic to stay OFF. |
|
# Options: [disable: 0, enable: 1] |
|
ps_active_high:1 |
|
|
|
#### Power Supply Auto Shutdown Mode |
|
# Used in case it is supported by the TFT. |
|
# Enable power supply auto shutdown after a print is finished when hotend temperature drops below target value. |
|
# Options: [disable: 0, enable: 1, auto-detect: 2] |
|
ps_auto_shutdown:0 |
|
|
|
#### Power Supply Auto Shutdown Temperature |
|
# Maximum hotend temperature for automatic shutdown after printing, if automatic shutdown is enabled. |
|
# The printer will shutdown automatically if the hotend temperature is below this value. |
|
# If the hotend temperature is higher than this value the fans will be turned on to cooldown and it |
|
# will wait for the hotend temperature to drop below this value before shutting down automatically. |
|
# Unit: [temperature in °C] |
|
# Value range: [min: 20, max: 1000] |
|
ps_auto_shutdown_temp:50 |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Filament Runout Settings (only if connected to TFT controller) |
|
#-------------------------------------------------------------------- |
|
|
|
# NOTES for users having a filament sensor connected to the mainboard: |
|
# 1) Define "fil_runout:0" below to disable the sensor handling on the TFT. |
|
# 2) Configure the sensor in the firmware of your mainboard. |
|
# 3) Add M75 to "start_gcode" and M77 to "end_gcode" of the TFT (or your slicer). |
|
|
|
#### Filament Runout Sensor |
|
# Select the type of filament runout sensor and its default enabled/disabled state. |
|
# Options: [Normal Disabled: 0, Normal Enabled: 1, Smart Disabled: 2, Smart Enabled: 3] |
|
fil_runout:1 |
|
|
|
#### Inverted Filament Runout Sensor Logic |
|
# The sensor uses an inverted logic. |
|
# Disable it in case filament runout is triggered by a LOW signal. |
|
# Enable it in case filament runout is triggered by a HIGH signal. |
|
# Options: [disable: 0, enable: 1] |
|
fil_runout_inverted:0 |
|
|
|
#### NC (Normal Close) Filament Runout Sensor |
|
# The sensor is of type NC. |
|
# Options: [Normal Open: 0, Normal Close: 1] |
|
fil_runout_nc:1 |
|
|
|
#### Filament Runout Noise Threshold |
|
# Pause print when filament runout is detected at least for this time period. |
|
# Unit: [time in milliseconds] |
|
# Value range: [min: 10, max: 1800] |
|
fil_runout_noise_threshold:200 |
|
|
|
#### Smart Filament Runout Detection |
|
# Used in conjunction with an SFS (Smart Filament Sensor) based on an encoder disc that |
|
# toggles runout pin as filament moves. |
|
# Unit: [distance in mm] |
|
# Value range: [min: 1, max: 50] |
|
fil_runout_distance:7 |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Power Loss Recovery & BTT UPS Settings |
|
#-------------------------------------------------------------------- |
|
|
|
#### Power Loss Recovery Mode |
|
# Enable power loss recovery. |
|
# Disable to reduce the loss of TFT SD card or TFT USB disk. |
|
# Options: [disable: 0, enable: 1] |
|
pl_recovery:1 |
|
|
|
#### Power Loss Recovery Homing |
|
# Home before power loss recovery. |
|
# Options: [disable: 0, enable: 1] |
|
pl_recovery_home:0 |
|
|
|
#### Power Loss Recovery Z Raise |
|
# Raise Z axis on resume (on power loss with UPS). |
|
# Unit: [distance in mm] |
|
# Value range: [min: 0.0, max: 2000.0] |
|
pl_recovery_z_raise:10.0 |
|
|
|
#### BTT Mini UPS Support |
|
# Enable backup power/UPS to move Z axis on power loss. |
|
# Options: [disable: 0, enable: 1] |
|
btt_mini_ups:0 |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Other Device-Specific Settings |
|
#-------------------------------------------------------------------- |
|
|
|
#### Sounds / Buzzer |
|
# Set sound ON or OFF. |
|
# |
|
# NOTE: Error messages from printer will always play the error sound. |
|
# |
|
# Parameters: |
|
# touch_sound: Enable/disable this to control touch feedback sound. |
|
# toast_sound: Enable/disable this to control all toast notification sounds. |
|
# alert_sound: Enable/disable this to control all popup and alert sounds |
|
# like print finish alert, dialog sound etc. |
|
# heater_sound: Enable/disable this to control acoustic feedback when temperature |
|
# has reached the desired value on heaters (nozzle, bed, chamber). |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
touch_sound:1 |
|
toast_sound:1 |
|
alert_sound:1 |
|
heater_sound:1 |
|
|
|
#### LCD Brightness Levels (only for TFT28/TFT35/TFT43/TFT50/TFT70 V3.0) |
|
# Brightness levels for LCD. |
|
# Options: [OFF: 0, 5%: 1, 10%: 2, 20%: 3, 30%: 4, 40%: 5, 50%: 6, 60%: 7, 70%: 8, 80%: 9, 90%: 10, 100%: 11] |
|
|
|
## LCD brightness level |
|
lcd_brightness:11 |
|
|
|
## LCD brightness level when device is idle |
|
lcd_idle_brightness:5 |
|
|
|
#### LCD Idle Time (only for TFT28/TFT35/TFT43/TFT50/TFT70 V3.0) |
|
# The LCD screen will dim to idle brightness, if the display is not touched for the |
|
# period of the LCD idle time. |
|
# Options: [OFF: 0, 5sec: 1, 10sec: 2, 30sec: 3, 1min: 4, 2min: 5, 5min: 6, 10min: 7] |
|
lcd_idle_time:4 |
|
|
|
#### LCD Lock On Idle (only for TFT28/TFT35/TFT43/TFT50/TFT70 V3.0) |
|
# If enabled, when the LCD is idle (dimmed) then the first touch on the display will |
|
# simply restore the normal LCD brightness. The touch is then skipped, preventing to |
|
# trigger any undesired action due to the dimmed display. |
|
# |
|
# NOTE: The lock is always avoided if the LCD brightness is restored by the use of |
|
# rotary encoder instead of touching the display. |
|
# |
|
# Options: [disable: 0, enable: 1] |
|
lcd_lock_on_idle:0 |
|
|
|
#### LED Color |
|
# Printer's LED color used by some features such as Event LED and PID processes. |
|
# Format: [led_color: R:<component> G:<component> B:<component> W:<component> P:<component> I:<component> |
|
# Target component: R: Red |
|
# G: Green |
|
# B: Blue |
|
# W: White; NEOPIXEL or RGB(W) |
|
# P: Intensity; NEOPIXEL |
|
# I: Index; NEOPIXEL |
|
# Value range: [min: 0, max: 255] |
|
led_color:R:255 G:255 B:255 W:255 P:255 I:255 |
|
|
|
#### LED Always ON |
|
# Keep printers's LED on at startup and after Event LED and PID processes terminate. |
|
# The printer's LED color is configured in "led_color". |
|
# Options: [disable: 0, enable: 1] |
|
led_always_on:0 |
|
|
|
#### Knob LED Color (only for TFT28/TFT35_E3/TFT43/TFT50/TFT70 V3.0) |
|
# Knob LED color at startup. |
|
# Options: [OFF: 0, WHITE: 1, RED: 2, ORANGE: 3, YELLOW: 4, GREEN: 5, BLUE: 6, INDIGO: 7, VIOLET: 8] |
|
knob_led_color:0 |
|
|
|
#### Knob LED Idle State (only for TFT28/TFT35_E3/TFT43/TFT50/TFT70 V3.0) |
|
# If enabled, when the LCD is idle (dimmed) then the knob LED will be also switched off. |
|
# Options: [disable: 0, enable: 1] |
|
knob_led_idle:1 |
|
|
|
#### Knob LED Pixels (only for TFT28/TFT35_E3/TFT43/TFT50/TFT70 V3.0) |
|
# Set the number of LEDs in the strip connected to "Neopixel" port of TFT. |
|
# It shares the same signal line as "knob_led". 0 means the default number in TFT hardware. |
|
# Greater than 0 means the number of LEDs in the strip. |
|
# Value range: [min: 0, max: 200] |
|
neopixel_pixels:0 |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Custom G-code Commands |
|
#-------------------------------------------------------------------- |
|
|
|
#### Custom G-code Commands |
|
# Up to 15 custom G-code commands that will be available in the Custom menu. |
|
# |
|
# Usage: |
|
# - To enable a custom command, remove "#" at the beginning of custom commands label & G-code. |
|
# - To disable a custom command, add "#" at the beginning of custom commands label & G-code. |
|
# |
|
# NOTE: If the values are left blank then default name and G-code will be used. |
|
# |
|
# Value range: label: [min: 3, max: 75 characters] |
|
# G-code: [min: 3, max: 75 characters] |
|
custom_label_1:Present extruder |
|
custom_gcode_1:G90\nG0 F3000 X0 Y0 Z100\n |
|
custom_label_2:Present bed |
|
custom_gcode_2:G90\nG0 F3000 X0 Y210 Z100\n |
|
custom_label_3:Disable all steppers |
|
custom_gcode_3:M84\n |
|
#custom_label_4:custom4 |
|
#custom_gcode_4:M105\n |
|
#custom_label_5:custom5 |
|
#custom_gcode_5:M105\n |
|
#custom_label_6:custom6 |
|
#custom_gcode_6:M105\n |
|
#custom_label_7:custom7 |
|
#custom_gcode_7:M105\n |
|
#custom_label_8:custom8 |
|
#custom_gcode_8:M105\n |
|
#custom_label_9:custom9 |
|
#custom_gcode_9:M105\n |
|
#custom_label_10:custom10 |
|
#custom_gcode_10:M105\n |
|
#custom_label_11:custom11 |
|
#custom_gcode_11:M105\n |
|
#custom_label_12:custom12 |
|
#custom_gcode_12:M105\n |
|
#custom_label_13:custom13 |
|
#custom_gcode_13:M105\n |
|
#custom_label_14:custom14 |
|
#custom_gcode_14:M105\n |
|
#custom_label_15:custom15 |
|
#custom_gcode_15:M105\n |
|
|
|
|
|
#-------------------------------------------------------------------- |
|
# Start, End & Cancel G-code Commands |
|
#-------------------------------------------------------------------- |
|
|
|
# NOTES for users having a filament sensor connected to the mainboard: |
|
# 1) Enable the start/end G-code below. |
|
# 2) Add the following commands to the start/end G-code: |
|
# - start_gcode: M75\n |
|
# - end_gcode: M77\n |
|
|
|
#### Start G-code Status |
|
# Options: [disable: 0, enable: 1] |
|
start_gcode_enabled:0 |
|
|
|
#### End G-code Status |
|
# Options: [disable: 0, enable: 1] |
|
end_gcode_enabled:0 |
|
|
|
#### Cancel G-code Status |
|
# Options: [disable: 0, enable: 1] |
|
cancel_gcode_enabled:1 |
|
|
|
#### Start G-code |
|
# This G-code will run before starting a print if "start_gcode_enabled" is enabled. |
|
# Value range: [min: 3, max: 75 characters] |
|
start_gcode:G28 XY R20\n |
|
|
|
#### End G-code |
|
# This G-code will run after a print is completed if "end_gcode_enabled" is enabled. |
|
# Value range: [min: 3, max: 75 characters] |
|
# M104: turn off extruder; M140: turn off bed; M107: turn off print cooling fan; M18: disable steppers |
|
end_gcode:M104 S0\nM140 S0\nM107\nM18\n |
|
|
|
#### Cancel G-code |
|
# This G-code will run when a print is cancelled if "cancel_gcode_enabled" is enabled. |
|
# Value range: [min: 3, max: 75 characters] |
|
# M104: turn off extruder; M140: turn off bed; G28: raise & home; G0: present bed; M107: turn off print cooling fan; M18: disable steppers |
|
cancel_gcode:M104 S0\nM140 S0\nG28 X R10\nG0 F3000 Y200\nM107\nM18\n |
thank you for this :)