Better boot.txt

U-Boot 1.1.4--LSDK-10.2.85 (Sep  3 2014 - 16:45:27)

EAP1018A1-FLF-FW - Scorpion 1.0

DRAM:  128 MB

cpu_pll_cfg: 0x21480  cpu_pll_dither: 0x3c103f
CFG_PLL_FREQ: 0x2  CFG_HZ: 360000000
CPU Clock: 720MHz    DDR Clock: 680MHz

Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
flash-2 size 16MB, sector count = 256
Flash: 16 *2 MB


U-Boot 1.1.4--LSDK-10.2.85 (Sep  3 2014 - 16:45:27)

EAP1018A1-FLF-FW - Scorpion 1.0

DRAM:

U-Boot 1.1.4--LSDK-10.2.85 (Sep  3 2014 - 16:45:27)

EAP1018A1-FLF-FW - Scorpion 1.0

DRAM:  128 MB

cpu_pll_cfg: 0x21480  cpu_pll_dither: 0x3c103f
CFG_PLL_FREQ: 0x2  CFG_HZ: 360000000
CPU Clock: 720MHz    DDR Clock: 680MHz

Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
flash-2 size 16MB, sector count = 256
Flash: 16 *2 MB
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0x1
Fetching MAC Address from 0x87fedb6c
ath_gmac_enet_initialize: reset mask:c02200
Scorpion  ----> 8035 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:11:74:ed:20:3f
ATHR_AUTONEG_ADVERT:1DE1
ATHR_1000BASET_CONTROL:200
ATHR_PHY_CONTROL:3100
ATHRSF1_PHY: Port 5, Neg Success
ATHRSF1_PHY: unit 0 phy addr 5 eth0 up
eth0
Setting 0x18116290 to 0x1020214f
Hit any key to stop autoboot:  0
multiboot=1
Trying eth0
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.1.100; our IP address is 192.168.1.1
Filename 'c65_atnboot.bin'.
Load address: 0x81000000
Loading: T #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###########################
done
Bytes transferred = 3464544 (34dd60 hex)

## Checking Image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.121
   Created:      2019-05-31  19:01:33 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3464480 Bytes =  3.3 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
## Booting image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.121
   Created:      2019-05-31  19:01:33 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3464480 Bytes =  3.3 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x81000040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[    0.000000] Linux version 4.14.121 (osboxes@osboxes) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10114-a1210f8888)) #0 Fri May 31 19:01:33 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[    0.000000] MIPS: machine is AirTight C-65
[    0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 117744K/131072K available (3790K kernel code, 145K rwdata, 912K rodata, 6664K init, 204K bss, 13328K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 51
[    0.000000] CPU clock: 720.000 MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[    0.000007] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[    0.008288] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[    0.074976] pid_max: default: 32768 minimum: 301
[    0.080054] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.087086] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.097722] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.108214] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.114758] pinctrl core: initialized pinctrl subsystem
[    0.121023] NET: Registered protocol family 16
[    0.131163] PCI host bridge /ahb/apb/pcie-controller@180c0000 ranges:
[    0.138024]  MEM 0x0000000010000000..0x0000000011ffffff
[    0.143604]   IO 0x0000000000000000..0x0000000000000000
[    0.161478] PCI host bridge to bus 0000:00
[    0.165875] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.173185] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.179116] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.186331] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.195171] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    0.202963] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[    0.212520] clocksource: Switched to clocksource MIPS
[    0.218695] NET: Registered protocol family 2
[    0.223965] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.231384] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.238187] TCP: Hash tables configured (established 1024 bind 1024)
[    0.245050] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.251269] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.258153] NET: Registered protocol family 1
[    0.352081] Crashlog allocated RAM at address 0x3f00000
[    0.358625] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.369321] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.375553] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.437103] io scheduler noop registered
[    0.441275] io scheduler deadline registered (default)
[    0.448480] pinctrl-single 1804002c.pinmux: 544 pins at pa b804002c size 68
[    0.456741] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.464085] console [ttyS0] disabled
[    0.467917] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 2500000) is a 16550A
[    0.477120] console [ttyS0] enabled
[    0.477120] console [ttyS0] enabled
[    0.484540] bootconsole [early0] disabled
[    0.484540] bootconsole [early0] disabled
[    0.497605] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    0.502802] 5 fixed-partitions partitions found on MTD device spi0.0
[    0.509240] Creating 5 MTD partitions on "spi0.0":
[    0.514119] 0x000000000000-0x000000040000 : "u-boot"
[    0.519774] 0x000000040000-0x000000060000 : "uboot-env"
[    0.525706] 0x000000060000-0x000000260000 : "kernel"
[    0.531350] 0x000000260000-0x000000ff0000 : "rootfs"
[    0.536993] mtd: device 3 (rootfs) set to be root filesystem
[    0.542812] mtdsplit: no squashfs found in "rootfs"
[    0.547780] 0x000000ff0000-0x000001000000 : "art"
[    0.554008] libphy: Fixed MDIO Bus: probed
[    0.560062] ag71xx 19000000.eth: invalid MAC address, using random address
[    0.904200] libphy: ag71xx_mdio: probed
[    1.023014] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:05 [uid=004dd072, driver=Atheros 8035 ethernet]
[    1.033766] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: rgmii
[    1.040247] ag71xx 1a000000.eth: invalid MAC address, using random address
[    1.384188] libphy: ag71xx_mdio: probed
[    1.403858] ag71xx 1a000000.eth: connected to PHY at mdio-bus.1:01 [uid=00000000, driver=Generic PHY]
[    1.413725] eth1: Atheros AG71xx at 0xba000000, irq 5, mode: sgmii
[    1.421258] NET: Registered protocol family 10
[    1.428948] Segment Routing with IPv6
[    1.432783] NET: Registered protocol family 17
[    1.437327] 8021q: 802.1Q VLAN Support v1.8
[    1.462968] Freeing unused kernel memory: 6664K
[    1.467568] This architecture does not have kernel memory protection.
[    1.484576] init: Console is alive
[    1.488186] init: - watchdog -
[    1.506588] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    1.515145] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    1.523863] init: - preinit -
[    1.677996] random: jshn: uninitialized urandom read (4 bytes read)
[    1.727124] random: jshn: uninitialized urandom read (4 bytes read)
[    1.748623] random: jshn: uninitialized urandom read (4 bytes read)
[    1.872851] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    3.632518] random: fast init done
[    4.990248] procd: - early -
[    4.993783] procd: - watchdog -
[    5.532597] procd: - watchdog -
[    5.535984] procd: - ubus -
[    5.544026] urandom_read: 3 callbacks suppressed
[    5.544032] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.589019] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.595835] random: ubusd: uninitialized urandom read (4 bytes read)
[    5.603076] procd: - init -
Please press Enter to activate this console.
[    5.747391] kmodloader: loading kernel modules from /etc/modules.d/*
[    5.758511] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    5.770107] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7
[    5.777819] Backport generated by backports.git v4.19.32-1-0-g1c4f7569
[    5.786709] ip_tables: (C) 2000-2006 Netfilter Core Team
[    5.798344] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    5.847410] xt_time: kernel timezone is -0000
[    5.894326] PPP generic driver version 2.4.2
[    5.900601] NET: Registered protocol family 24
[    5.958517] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=13
[    5.999983] kmodloader: done loading kernel modules from /etc/modules.d/*
[   24.195356] eth0: link up (1000Mbps/Full duplex)
[   24.200434] br-lan: port 1(eth0) entered blocking state
[   24.205786] br-lan: port 1(eth0) entered disabled state
[   24.211318] device eth0 entered promiscuous mode
[   24.229610] br-lan: port 1(eth0) entered blocking state
[   24.234948] br-lan: port 1(eth0) entered forwarding state
[   24.240544] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   24.307903] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   25.232541] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  130.622556] random: crng init done
[  130.626019] random: 1 urandom warning(s) missed due to ratelimiting



BusyBox v1.30.1 () built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r10114-a1210f8888
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#