BLE400 custom board file

custom_board.h

#ifndef BLE400_H
#define BLE400_H

// LEDs definitions for BLE400
#define LEDS_NUMBER    5

#define LED_START      18
#define LED_1          18
#define LED_2          19
#define LED_3          20
#define LED_4          21
#define LED_5          22
#define LED_STOP       22

#define LEDS_LIST { LED_1, LED_2, LED_3, LED_4, LED_5 }

#define BSP_LED_0      LED_1
#define BSP_LED_1      LED_2
#define BSP_LED_2      LED_3
#define BSP_LED_3      LED_4
#define BSP_LED_4      LED_5

#define BSP_LED_0_MASK (1<<BSP_LED_0)
#define BSP_LED_1_MASK (1<<BSP_LED_1)
#define BSP_LED_2_MASK (1<<BSP_LED_2)
#define BSP_LED_3_MASK (1<<BSP_LED_3)
#define BSP_LED_4_MASK (1<<BSP_LED_4)

#define LEDS_MASK      (BSP_LED_0_MASK | BSP_LED_1_MASK | BSP_LED_2_MASK | BSP_LED_3_MASK | BSP_LED_4_MASK)
/* all LEDs are lit when GPIO is low */
#define LEDS_INV_MASK  LEDS_MASK

#define BUTTONS_NUMBER 2

#define BUTTON_START   16
#define BUTTON_1       16
#define BUTTON_2       17
#define BUTTON_STOP    17
#define BUTTON_PULL    NRF_GPIO_PIN_PULLUP

#define BUTTONS_LIST { BUTTON_1, BUTTON_2 }

#define BSP_BUTTON_0   BUTTON_1
#define BSP_BUTTON_1   BUTTON_2

#define BSP_BUTTON_0_MASK (1<<BSP_BUTTON_0)
#define BSP_BUTTON_1_MASK (1<<BSP_BUTTON_1)

#define BUTTONS_MASK   0x001E0000

#define RX_PIN_NUMBER  9
#define TX_PIN_NUMBER  11
#define CTS_PIN_NUMBER 8
#define RTS_PIN_NUMBER 10
#define HWFC           true

#define SPIS_MISO_PIN   28  // SPI MISO signal.
#define SPIS_CSN_PIN    12  // SPI CSN signal.
#define SPIS_MOSI_PIN   25  // SPI MOSI signal.
#define SPIS_SCK_PIN    29  // SPI SCK signal.

#define SPIM0_SCK_PIN   29  // SPI clock GPIO pin number.
#define SPIM0_MOSI_PIN  25  // SPI Master Out Slave In GPIO pin number.
#define SPIM0_MISO_PIN  28  // SPI Master In Slave Out GPIO pin number.
#define SPIM0_SS_PIN    12  // SPI Slave Select GPIO pin number.

#define SPIM1_SCK_PIN   2   // SPI clock GPIO pin number.
#define SPIM1_MOSI_PIN  3   // SPI Master Out Slave In GPIO pin number.
#define SPIM1_MISO_PIN  4   // SPI Master In Slave Out GPIO pin number.
#define SPIM1_SS_PIN    5   // SPI Slave Select GPIO pin number.

#define SPIM2_SCK_PIN   12  // SPI clock GPIO pin number.
#define SPIM2_MOSI_PIN  13  // SPI Master Out Slave In GPIO pin number.
#define SPIM2_MISO_PIN  14  // SPI Master In Slave Out GPIO pin number.
#define SPIM2_SS_PIN    15  // SPI Slave Select GPIO pin number.

// serialization APPLICATION board - temp. setup for running serialized MEMU tests
#define SER_APP_RX_PIN              31    // UART RX pin number.
#define SER_APP_TX_PIN              30    // UART TX pin number.
#define SER_APP_CTS_PIN             28    // UART Clear To Send pin number.
#define SER_APP_RTS_PIN             29    // UART Request To Send pin number.

#define SER_APP_SPIM0_SCK_PIN        2     // SPI clock GPIO pin number.
#define SER_APP_SPIM0_MOSI_PIN       4     // SPI Master Out Slave In GPIO pin number
#define SER_APP_SPIM0_MISO_PIN       3     // SPI Master In Slave Out GPIO pin number
#define SER_APP_SPIM0_SS_PIN        31     // SPI Slave Select GPIO pin number
#define SER_APP_SPIM0_RDY_PIN       29     // SPI READY GPIO pin number
#define SER_APP_SPIM0_REQ_PIN       30     // SPI REQUEST GPIO pin number

// serialization CONNECTIVITY board
#define SER_CON_RX_PIN              13    // UART RX pin number.
#define SER_CON_TX_PIN              12    // UART TX pin number.
#define SER_CON_CTS_PIN             14    // UART Clear To Send pin number. Not used if HWFC is set to false.
#define SER_CON_RTS_PIN             15    // UART Request To Send pin number. Not used if HWFC is set to false.

#define SER_CON_SPIS_SCK_PIN        29    // SPI SCK signal.
#define SER_CON_SPIS_MOSI_PIN       25    // SPI MOSI signal.
#define SER_CON_SPIS_MISO_PIN       28    // SPI MISO signal.
#define SER_CON_SPIS_CSN_PIN        12    // SPI CSN signal.
#define SER_CON_SPIS_RDY_PIN        14    // SPI READY GPIO pin number.
#define SER_CON_SPIS_REQ_PIN        13    // SPI REQUEST GPIO pin number.

#define SER_CONN_CHIP_RESET_PIN     27    // Pin used to reset connectivity chip

// Arduino board mappings
#define ARDUINO_SCL_PIN             27    // SCL signal pin
#define ARDUINO_SDA_PIN             26    // SDA signal pin
#define ARDUINO_AREF_PIN            2     // Aref pin
#define ARDUINO_13_PIN              25    // Digital pin 13
#define ARDUINO_12_PIN              24    // Digital pin 12
#define ARDUINO_11_PIN              23    // Digital pin 11
#define ARDUINO_10_PIN              22    // Digital pin 10
#define ARDUINO_9_PIN               20    // Digital pin 9
#define ARDUINO_8_PIN               19    // Digital pin 8

#define ARDUINO_7_PIN               18    // Digital pin 7
#define ARDUINO_6_PIN               17    // Digital pin 6
#define ARDUINO_5_PIN               16    // Digital pin 5
#define ARDUINO_4_PIN               15    // Digital pin 4
#define ARDUINO_3_PIN               14    // Digital pin 3
#define ARDUINO_2_PIN               13    // Digital pin 2
#define ARDUINO_1_PIN               12    // Digital pin 1
#define ARDUINO_0_PIN               11    // Digital pin 0

#define ARDUINO_A0_PIN              3     // Analog channel 0
#define ARDUINO_A1_PIN              4     // Analog channel 1
#define ARDUINO_A2_PIN              28    // Analog channel 2
#define ARDUINO_A3_PIN              29    // Analog channel 3
#define ARDUINO_A4_PIN              30    // Analog channel 4
#define ARDUINO_A5_PIN              31    // Analog channel 5

// Low frequency clock source to be used by the SoftDevice
#define NRF_CLOCK_LFCLKSRC      NRF_CLOCK_LFCLKSRC_XTAL_20_PPM

#endif // BLE400_H